Professional Documents
Culture Documents
SECTION
WARNING CHIME SYSTEM
WCS B
E
CONTENTS
HOW TO USE THIS MANUAL ...................... 3 SEAT BELT REMINDER WARNING CHIME : F
System Description ..................................................16
APPLICATION NOTICE ...................................... 3
Information ................................................................ 3 LIGHT REMINDER WARNING CHIME .....................17
G
LIGHT REMINDER WARNING CHIME : System
PRECAUTION ............................................... 4 Diagram ...................................................................18
LIGHT REMINDER WARNING CHIME : System
PRECAUTIONS ................................................... 4 Description ...............................................................18 H
WCS-1
COMMON ITEM : CONSULT-III Function (BCM - DTC/CIRCUIT DIAGNOSIS ........................ 82
COMMON ITEM) .................................................... 32
POWER SUPPLY AND GROUND CIRCUIT ..... 82
BUZZER .................................................................... 33
BUZZER : CONSULT Function (BCM - BUZZER)... 33 COMBINATION METER ............................................ 82
COMBINATION METER : Diagnosis Procedure ..... 82
DIAGNOSIS SYSTEM (BCM) (WITHOUT IN-
TELLIGENT KEY SYSTEM) .............................. 35 METER BUZZER CIRCUIT ............................... 83
Component Function Check ................................... 83
COMMON ITEM ........................................................ 35 Diagnosis Procedure .............................................. 83
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) .................................................... 35 PARKING BRAKE SWITCH SIGNAL CIR-
CUIT ................................................................... 84
BUZZER .................................................................... 35 Diagnosis Procedure ............................................... 84
BUZZER : CONSULT Function (BCM - BUZZER)... 36 Component Inspection ............................................ 84
ECU DIAGNOSIS INFORMATION .............. 37 SYMPTOM DIAGNOSIS ............................ 85
COMBINATION METER .................................... 37 THE PARKING BRAKE RELEASE WARNING
Reference Value ..................................................... 37 CONTINUES SOUNDING, OR DOES NOT
Fail-Safe ................................................................. 56
SOUND .............................................................. 85
DTC Index .............................................................. 59
Description .............................................................. 85
BCM (BODY CONTROL MODULE) .................. 60 Diagnosis Procedure ............................................... 85
List of ECU Reference ............................................ 60
THE SEAT BELT REMINDER WARNING
WIRING DIAGRAM ..................................... 61 CONTINUES SOUNDING, OR DOES NOT
SOUND .............................................................. 86
WARNING CHIME SYSTEM ............................. 61 Description .............................................................. 86
Diagnosis Procedure ............................................... 86
TYPE A ...................................................................... 61
TYPE A : Wiring Diagram ....................................... 61 THE LIGHT REMINDER WARNING DOES
TYPE B ...................................................................... 66
NOT SOUND ...................................................... 88
Description .............................................................. 88
TYPE B : Wiring Diagram ....................................... 66
Diagnosis Procedure ............................................... 88
TYPE C ...................................................................... 72
TYPE C : Wiring Diagram ....................................... 72 THE KEY WARNING DOES NOT SOUND
(WITHOUT INTELLIGENT KEY) ....................... 89
TYPE D ...................................................................... 78 Description .............................................................. 89
TYPE D : Wiring Diagram ....................................... 78 Diagnosis Procedure ............................................... 89
WCS-2
APPLICATION NOTICE
< HOW TO USE THIS MANUAL >
HOW TO USE THIS MANUAL A
APPLICATION NOTICE
Information INFOID:0000000006882266
B
• In this manual, “Idling Stop System” is referred to as “Stop / Start System”.
• Both “VDC” and “ESP” are used in this manual. These indicate the same system.
• Check destination to use the service information in this section. C
WCS
WCS-3
PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
EXCEPT FOR EUROPE
EXCEPT FOR EUROPE : Precaution for Supplemental Restraint System (SRS) "AIR
BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000006844453
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
FOR EUROPE
FOR EUROPE : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and
"SEAT BELT PRE-TENSIONER" INFOID:0000000006844454
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
The vehicle may be equipped with a passenger air bag deactivation switch. Because no rear seat exists where
a rear-facing child restraint can be placed, the switch is designed to turn off the passenger air bag so that a
rear-facing child restraint can be used in the front passenger seat. The switch is located in the center of the
instrument panel, near the ashtray. When the switch is turned to the ON position, the passenger air bag is
enabled and could inflate for certain types of collision. When the switch is turned to the OFF position, the pas-
senger air bag is disabled and will not inflate. A passenger air bag OFF indicator on the instrument panel lights
up when the passenger air bag is switched OFF. The driver air bag always remains enabled and is not affected
by the passenger air bag deactivation switch.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
WCS-4
PRECAUTIONS
< PRECAUTION >
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag A
Module, see the “SRS AIR BAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
B
ness connectors.
• The vehicle may be equipped with a passenger air bag deactivation switch which can be operated by
the customer. When the passenger air bag is switched OFF, the passenger air bag is disabled and
will not inflate. When the passenger air bag is switched ON, the passenger air bag is enabled and C
could inflate for certain types of collision. After SRS maintenance or repair, make sure the passenger
air bag deactivation switch is in the same position (ON or OFF) as when the vehicle arrived for ser-
vice. D
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation. E
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly F
causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
G
WCS
WCS-5
COMPONENT PARTS
< SYSTEM DESCRIPTION >
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location INFOID:0000000005887662
JSNIA3822ZZ
WCS-6
COMPONENT PARTS
< SYSTEM DESCRIPTION >
Component Description INFOID:0000000005887663
Unit Description
Receives a buzzer output signal from the BCM with CAN communication line and sounds the B
buzzer.
MODELS WITH ABS [EXCEPT FOR EUROPE AND AUSTRALIA]
• Controls the following with the vehicle speed signal received from ABS actuator and electric
unit (control unit) via CAN communication and the signals from switches. C
- Parking brake release warning chime
A/T MODELS WITHOUT ABS
• Controls the following with the vehicle speed signal received from TCM via CAN communica-
tion and the signals from switches.
D
- Parking brake release warning chime
M/T MODELS WITHOUT ABS
Combination meter • Controls the following with the vehicle speed sensor signal received from vehicle speed sen- E
sor and the signals from switches.
- Parking brake release warning chime
FOR EUROPE AND AUSTRALIA
• Controls the following with the vehicle speed signal received from ABS actuator and electric F
unit (control unit) via CAN communication and the signals from switches.
- Parking brake release warning chime
- Seat belt reminder warning chime
HR12DDR G
• Controls the following with the engine speed signal, stop/start readiness signal and stop/start
indicator signal received from ECM via CAN communication and the signals from switches.
- Stop/start system reminder warning chime
H
Based on the signals received from various units and switches, transmits the buzzer output sig-
BCM
nal to the combination meter via CAN communication.
ABS actuator and electric unit
(control unit) (Models with ABS)
Transmits the vehicle speed signal to the combination meter via CAN communication. I
WCS-7
COMPONENT PARTS
< SYSTEM DESCRIPTION >
Combination Meter INFOID:0000000005887664
The buzzer (1) for the warning chime system is integrated in the
combination meter.
JSNIA2928ZZ
WCS-8
SYSTEM
< SYSTEM DESCRIPTION >
SYSTEM
A
WARNING CHIME SYSTEM
WARNING CHIME SYSTEM : System Diagram INFOID:0000000005887665
B
I
JSNIA4426GB
COMBINATION METER
The combination meter sounds the alarm buzzer installed in the combination meter when receiving the buzzer K
output signal transmitted from each unit.
BCM
BCM receives signals from various units and transmits a buzzer output signal to the combination meter via L
CAN communication if it judges that the warning buzzer should be activated.
WARNING CHIME FUNCTION LIST
M
Warning functions Out line Warning judgment unit Refer to
WCS-14,
"PARKING WCS
The warning chime sounds when the ignition
BRAKE RE-
switch is in ON position with the parking brake
Parking brake release warning chime Combination meter LEASE WARN-
in operation and the vehicle speed 7 km/h (4.3
ING CHIME :
MPH) or more. O
System De-
scription"
Combination meter WCS-16,
(Models for Europe and "SEAT BELT P
The warning chime sounds when vehicle
Seat belt reminder warning chime (Mod- Australia) REMINDER
speeds reach 15 km/h (9.3 MPH) or more with
els for Europe, Australia and Hong WARNING
the ignition switch ON and the driver unbuck-
Kong) CHIME : Sys-
led. BCM (For Hong Kong) tem Descrip-
tion"
WCS-9
SYSTEM
< SYSTEM DESCRIPTION >
Warning functions Out line Warning judgment unit Refer to
WCS-18,
"LIGHT RE-
The warning chime sounds when the ignition
MINDER
switch is in OFF or ACC position with the com-
Light reminder warning chime BCM WARNING
bination switch (lighting switch) in the 1st or
CHIME : Sys-
2nd position and the driver side door open.
tem Descrip-
tion"
WCS-19,
"FRONT FOG
The warning chime sounds when the ignition
LIGHT RE-
Front fog light reminder warning chime switch is turned to OFF position from ON po-
MINDER
(With Auto light system and front fog sition, with combination switch (lighting BCM
WARNING
lamp system models) switch) is in AUTO position and the front fog
CHIME : Sys-
lamp switch in ON position.
tem Descrip-
tion"
WCS-20, "KEY
The warning chime sounds when the ignition WARNING
Key warning chime (Without intelligent
switch is in OFF or ACC position with the key BCM CHIME : Sys-
key system models)
inserted and the driver side door open. tem Descrip-
tion"
WCS-22, "RE-
The reverse warning chime sounds when the VERSE WARN-
Reverse warning chime (For Hong
ignition switch is in ON position with the selec- BCM ING CHIME :
Kong)
tor lever in R position. System De-
scription"
• The warning chime sounds when the driver WCS-25,
side door is open while the stop/start indica- "STOP/START
tor lamp blinks at a high speed. (CVT mod- SYSTEM RE-
Stop/start system reminder warning els) MINDER
Combination meter
chime (HR12DDR) • The warning chime sounds when the driver WARNING
side door is open or the driver seat belt un- CHIME : Sys-
fastened while the stop/start indicator lamp tem Description
blinks at a high speed. (M/T models) (M/T models)"
Function Specifications
Speedometer (A/T or CVT models)
Reset to zero by suspending communication.
Tachometer
When suspending communication, changes to nighttime
Illumination control
mode.
Current fuel consumption 0 km/h is displayed.
Average fuel consumption • When reception time of an abnormal signal is 2 sec-
onds or less, the last received datum is used for cal-
Trip computer culation to indicate the result.
Distance to empty • When reception time of an abnormal signal is more
Information dis- than 2 seconds, the last result calculated during nor-
play mal condition is indicated.
An indicated value is maintained at communications
Odo/trip meter
blackout.
Shift position indicator The indicator turns OFF by suspending communication.
Engine start operation indicator The indicator turns OFF by suspending communication.
Buzzer The buzzer turns off by suspending communication.
WCS-10
SYSTEM
< SYSTEM DESCRIPTION >
Function Specifications
A
ABS warning lamp
EPS warning lamp
Brake warning lamp (With ABS) B
Malfunction indicator (MI) (yellow) or Malfunction indica- The lamp turns ON by suspending communication.
tor lamp (MIL) (yellow)
ESP OFF indicator lamp C
SLIP indicator lamp
High water temperature warning lamp
D
High beam indicator lamp
Turn signal indicator lamp
Front fog lamp indicator lamp E
Rear fog lamp indicator lamp
Warning lamp/in- Door warning lamp
dicator lamp
Shift P warning lamp F
Key warning lamp
Oil pressure warning lamp
The lamp turns OFF by suspending communication. G
Stop/start indicator lamp
SPORT indicator lamp
OD OFF indicator lamp H
Glow indicator lamp
Malfunction indicator (MI) (Red)
I
Water-in-fuel-filter warning lamp
CRUISE indicator lamp
Speed limiter indicator lamp J
SET indicator lamp
Function Specifications
L
Speedometer
Reset to zero by suspending communication.
Tachometer
When suspending communication, changes to nighttime M
Illumination control
mode.
WCS
WCS-11
SYSTEM
< SYSTEM DESCRIPTION >
Function Specifications
Current fuel consumption • When reception time of an abnormal signal is 2 sec-
onds or less, the last received datum is used for cal-
Average fuel consumption
culation to indicate the result.
Average vehicle speed • When reception time of an abnormal signal is more
Trip computer than 2 seconds, the last result calculated during nor-
Distance to empty mal condition is indicated.
An indicated value is maintained at communications
Travel distance
blackout.
Door open warning
Interrupt indica-
Light reminder warning The indicator turns OFF by suspending communication.
tion
Seat belt reminder warning
An indicated value is maintained at communications
Accumulated time
blackout.
Current saved fuel consumption An indicated value is maintained at communications
(Except for HR12DDR) blackout.
• When reception time of an abnormal signal is 2 sec-
onds or less, the last received datum is used for cal-
Information dis- CO2 saved information culation to indicate the result.
play (HR12DDR) • When reception time of an abnormal signal is more
Idling stop dis- than 2 seconds, the last result calculated during nor-
play (with stop/ mal condition is indicated.
start system)
Engine stop guidance (HR12DDR)
Stop/start system off message
(HR12DDR) • When reception time of an abnormal signal is 2 sec-
onds or less, the last received datum is used to indi-
Stop/start system fault information cate the result.
(HR12DDR) • When reception time of an abnormal signal is more
Precautions on stop/start system in- than 2 seconds, the indicator turns OFF.
formation
(HR12DDR)
Parking sensor The indicator turns OFF by suspending communication.
Parking space measurement The indicator turns OFF by suspending communication.
An indicated value is maintained at communications
Odo/trip meter
blackout.
Shift position indicator The indicator turns OFF by suspending communication.
Engine start operation indicator The indicator turns OFF by suspending communication.
Buzzer The buzzer turns off by suspending communication.
WCS-12
SYSTEM
< SYSTEM DESCRIPTION >
Function Specifications
A
ABS warning lamp
EPS warning lamp
Brake warning lamp B
Malfunction indicator (MI) (yellow) or Malfunction indica- The lamp turns ON by suspending communication.
tor lamp (MIL) (yellow)
ESP OFF indicator lamp C
SLIP indicator lamp
High water temperature warning lamp
D
Low water temperature indicator lamp
High beam indicator lamp
Warning lamp/in- Turn signal indicator lamp
dicator lamp
E
Front fog lamp indicator lamp
Rear fog lamp indicator lamp
Shift P warning lamp F
The lamp turns OFF by suspending communication.
Key warning lamp
Oil pressure warning lamp
G
Stop/start indicator lamp
SPORT indicator lamp
OD OFF indicator lamp H
CRUISE indicator lamp
Speed limiter indicator lamp
I
PARKING BRAKE RELEASE WARNING CHIME
PARKING BRAKE RELEASE WARNING CHIME : System Diagram INFOID:0000000005887672
J
JSNIA2422GB
JSNIA2931GB
WCS-13
SYSTEM
< SYSTEM DESCRIPTION >
M/T MODELS
JSNIA2932GB
Operation conditions
Ignition switch ON
Parking brake During the operation (parking brake switch ON)
Vehicle speed Approximately 7 km/h (4.3 MPH) or more
Cancel conditions
Ignition switch OFF
Parking brake Release condition (parking brake switch OFF)
Vehicle speed Approximately 3 km/h (1.9 MPH) or less
SIGNAL PATH
Combination meter sounds integrated buzzer when it judges that parking brake release warning chime is nec-
essary from signals below.
MODELS WITH ABS
Vehicle speed signal ABS actuator and electric unit (control unit) Combination meter
M/T MODELS
WCS-14
SYSTEM
< SYSTEM DESCRIPTION >
Signal name Signal path
A
Parking brake switch signal Parking brake switch Combination meter
TIMING CHART
C
JSNIA2428GB
H
SOUND SPECIFICATION
K
JSNIA3091GB
WCS
JSNIA3824GB
P
WCS-15
SYSTEM
< SYSTEM DESCRIPTION >
FOR HONG KONG
JSNIA3118GB
Operation conditions
Ignition switch ON
Driver seat belt Unfastened [seat belt buckle switch (driver side) ON]
Vehicle speed 15 km/h (9.3 MPH) or more
Operation conditions
Ignition switch OFF
Driver seat belt Fastened [seat belt buckle switch (driver side) OFF]
90 seconds after the start of warning sound
SIGNAL PATH
For Europe and Australia
Combination meter sounds integrated buzzer when it judges that seat belt reminder warning chime is neces-
sary from signals below.
Vehicle speed signal ABS actuator and electric unit (control unit) Combination meter
Vehicle speed signal ABS actuator and electric unit (control unit) BCM
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.
WCS-16
SYSTEM
< SYSTEM DESCRIPTION >
JSNIA3825GB
SOUND SPECIFICATION H
K
JSNIA2594GB
WCS
JPNIA1772GB
O
LIGHT REMINDER WARNING CHIME
WCS-17
SYSTEM
< SYSTEM DESCRIPTION >
LIGHT REMINDER WARNING CHIME : System Diagram INFOID:0000000005887668
JSNIA2421GB
Operation conditions
Ignition switch OFF or ACC position
Combination switch (Lighting
1st or 2nd position
switch)
Driver door Open [front door switch (driver side) ON]
Cancel conditions
Ignition switch ON
Combination switch (Lighting
OFF
switch)
Driver door Close [front door switch (driver side) OFF]
SIGNAL PATH
1. BCM requires warning chime output to combination meter when it judges light reminder warning chime is
necessary from signals below.
Driver door switch signal Front door switch (driver side) BCM
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.
WCS-18
SYSTEM
< SYSTEM DESCRIPTION >
TIMING CHART
A
JSNIA2426GB F
FRONT FOG LIGHT REMINDER WARNING CHIME
FRONT FOG LIGHT REMINDER WARNING CHIME : System Diagram INFOID:0000000006834487
G
JSNIA3117GB
J
K
WARNING CHIME OPERATION CONDITIONS
Warning chime sounds during 2 seconds when the ignition switch is in LOCK, OFF or ACC position, if all of
below operation conditions is met. L
Operation conditions
Ignition switch ON position M
Combination switch (Lighting AUTO position and front fog lamp switch ON
switch) position
WCS
SIGNAL PATH
1. BCM requires warning chime output to combination meter when it judges front fog light reminder warning
chime is necessary from signals below.
O
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.
WCS-19
SYSTEM
< SYSTEM DESCRIPTION >
TIMING CHART
JSNIA3110GB
JSNIA2425GB
Operation conditions
Ignition switch OFF or ACC position
Key switch ON (state that inserted key in key cylinder)
Driver door Open [front door switch (driver side) ON]
Cancel conditions
Ignition switch ON
Key switch OFF (state that removed key from key cylinder)
Driver door Close [front door switch (driver side) OFF]
SIGNAL PATH
WCS-20
SYSTEM
< SYSTEM DESCRIPTION >
1. BCM requires warning chime output to combination meter when it judges key warning chime is necessary
from signals below. A
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
D
nal) from BCM.
TIMING CHART F
K
JSNIA2429GB
SOUND SPECIFICATION
L
WCS
JSNIA3092GB
O
REVERSE WARNING CHIME
WCS-21
SYSTEM
< SYSTEM DESCRIPTION >
REVERSE WARNING CHIME : System Diagram INFOID:0000000006845135
JSNIA3827GB
Operation conditions
Ignition switch ON
Shift position “R” position
Cancel conditions
Ignition switch OFF
Shift position Other than “R” position
SIGNAL PATH
1. BCM requires warning chime output to combination meter when it judges reverse warning chime is neces-
sary from signals below.
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.
WCS-22
SYSTEM
< SYSTEM DESCRIPTION >
TIMING CHART
A
E
JSNIA3826GB
SOUND SPECIFICATION
F
JPNIA1773GB
I
STOP/START SYSTEM REMINDER WARNING CHIME
STOP/START SYSTEM REMINDER WARNING CHIME : System Diagram INFOID:0000000007274956
WCS
JSNIA4427GB O
WCS-23
SYSTEM
< SYSTEM DESCRIPTION >
Operation conditions
Ignition switch ON
Stop/start system ON
Stop/start indicator
Blink (high speed)
lamp
Driver door Open [front door switch (driver side) ON]
Operation conditions
Ignition switch OFF
Stop/start system OFF
SIGNAL PATH
Combination meter sounds integrated buzzer when it judges that stop/start system reminder warning chime is
necessary from signals below.
Driver door switch signal Front door switch (driver side) BCM Combination meter
TIMING CHART
JSNIA4419GB
WCS-24
SYSTEM
< SYSTEM DESCRIPTION >
SOUND SPECIFICATION
A
JSNIA4429GB
D
STOP/START SYSTEM REMINDER WARNING CHIME : System Description (M/T
models) INFOID:0000000007274957
E
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled.
F
Operation conditions
Ignition switch ON
Stop/start system ON G
Stop/start indicator
Blink (high speed)
lamp
Driver seat belt unfastened or driver door is open.
H
Operation conditions
Ignition switch OFF J
Stop/start system OFF
SIGNAL PATH K
Combination meter sounds integrated buzzer when it judges that stop/start system reminder warning chime is
necessary from signals below.
L
Signal name Signal path
Ignition switch signal —
M
Driver door switch signal Front door switch (driver side) BCM Combination meter
WCS-25
SYSTEM
< SYSTEM DESCRIPTION >
TIMING CHART
JSNIA4432GB
SOUND SPECIFICATION
JSNIA4431GB
WCS-26
DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (COMBINATION METER)
A
CONSULT Function INFOID:0000000006844455
APPLICATION ITEMS B
CONSULT can perform the following diagnosis modes via CAN communication and the combination meter.
MAIN
Display item [Unit] Description
SIGNALS
G
• Value of vehicle speed signal received from ABS actuator and electric unit (con-
trol unit) via CAN communication. (Models with ABS)
NOTE:
655.35 is displayed when the malfunction signal is received. H
SPEED METER • Value of vehicle speed signal received from TCM via CAN communication. (A/
X
[km/h] T models without ABS)
NOTE:
655.35 is displayed when the malfunction signal is received. I
• Value of vehicle speed sensor signal received from vehicle speed sensor. (M/T
models)
Vehicle speed signal value transmitted to other units via CAN communication. J
SPEED OUTPUT
X NOTE:
[km/h]
655.35 is displayed when the malfunction signal is received.
ODO OUTPUT K
Odometer signal value transmitted to other units via CAN communication.
[km/h or mph]
Value of the engine speed signal received from ECM via CAN communication.
TACHO METER
X NOTE:
[rpm] L
8191.875 is displayed when the malfunction signal is received.
FUEL METER
X Fuel level indicated on combination meter.
[L]
M
Value of engine coolant temperature signal is received from ECM via CAN com-
W TEMP METER munication.
X
[°C] NOTE:
215 is displayed when the malfunction signal is input. WCS
INSTANT FUEL
Value of current fuel consumption calculated by combination meter.
[km/L]
ABS W/L Status of ABS warning lamp detected from ABS warning lamp signal is received O
[On/Off] from ABS actuator and electric unit (control unit) via CAN communication.
Status of ESP OFF indicator lamp detected from ESP OFF indicator lamp signal
VDC/TCS IND
is received from ABS actuator and electric unit (control unit) via CAN communica-
[On/Off] P
tion.
SLIP IND Status of SLIP indicator lamp detected from SLIP indicator lamp signal is received
[On/Off] from ABS actuator and electric unit (control unit) via CAN communication.
WCS-27
DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >
MAIN
Display item [Unit] Description
SIGNALS
Status of brake warning lamp detected from brake warning lamp signal is received
from ABS actuator and electric unit (control unit) via CAN communication.
BRAKE W/L
NOTE:
[On/Off]
Displays “Off” if the brake warning lamp is illuminated when the valve check starts,
the parking brake switch is turned ON or the brake fluid level switch is turned ON.
DOOR W/L Status of door warning detected from door switch signal received from BCM via
[On/Off] CAN communication.
HI-BEAM IND Status of high beam indicator lamp detected from high beam request signal is re-
[On/Off] ceived from BCM via CAN communication.
TURN IND Status of turn indicator lamp detected from turn indicator signal is received from
[On/Off] BCM via CAN communication.
FR FOG IND Status of front fog lamp indicator lamp detected from front fog light request signal
[On/Off] is received from BCM via CAN communication.
RR FOG IND Status of rear fog lamp indicator lamp detected from rear fog lamp status signal is
[On/Off] received from BCM via CAN communication.
• Status of oil pressure warning lamp detected from oil pressure switch signal is
received from BCM via CAN communication. (Except for Europe with stop/start
OIL W/L system)
[On/Off] • Status of oil pressure warning lamp detected from oil pressure warning lamp
signal is received from ECM via CAN communication. (For Europe with stop/
start system)
MIL Status of malfunction indicator lamp (yellow) detected from malfunctioning indica-
[On/Off] tor lamp signal is received from ECM via CAN communication.
GLOW IND Status of glow indicator lamp detected from glow indicator lamp signal is received
[On/Off] from ECM via CAN communication.
C-ENG2 W/L Status of malfunction indicator lamp (red) detected from malfunction indicator
[On/Off] lamp signal is received from ECM via CAN communication.
• Status of CRUISE indicator and CRUISE indicator lamp detected from ASCD
status signal is received from ECM via CAN communication. (With dot matrix
CRUISE IND
information display)
[On/Off]
• Status of CRUISE indicator lamp detected from ASCD status signal is received
from ECM via CAN communication. (With segment information display)
• Status of SET indicator detected from ASCD status signal or speed limiter op-
eration signal are received from ECM via CAN communication. (With dot matrix
SET IND information display)
[On/Off] • Status of SET indicator lamp detected from ASCD status signal or speed limiter
operation signal are received from ECM via CAN communication. (With seg-
ment information display)
O/D OFF IND Status of OD OFF indicator lamp detected from OD OFF indicator lamp signal is
[On/Off] received from TCM via CAN communication.
SPORT IND Status of SPORT indicator detected from sport mode switch signal is received
[On/Off] from CVT shift selector.
FUEL W/L
Low-fuel warning status detected by the identified fuel level.
[On/Off]
KEY G/Y W/L Status of KEY warning lamp (Green/Yellow) detected from KEY warning lamp sig-
[On/Off] nal is received from BCM via CAN communication.
EPS W/L Status of EPS warning lamp detected from EPS warning lamp signal is received
[On/Off] from EPS control unit via CAN communication.
e-4WD W/L
This item is displayed, but cannot be monitored.
[Off]
DPF W/L
This item is displayed, but cannot be monitored.
[Off]
FILTER W/L Status of water-in-fuel-filter warning lamp detected from water-in-fuel-filter warn-
[On/Off] ing lamp signal is received from ECM via CAN communication.
WCS-28
DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >
MAIN
Display item [Unit] Description
SIGNALS A
• Displays status of Intelligent Key system warning judged from meter display sig-
nal received from BCM with CAN communication line. (With dot matrix informa-
LCD
tion display) B
[B&P N, B&P I, C&P N, C&P I, LK
• Status of engine start operation indicator, shift P warning lamp and KEY warning
WN, ROTAT, SFT P, NO KY, ID NG,
lamp, detected from engine start operation indicator signal, shift P warning lamp
BATT]
signal and KEY warning lamp signal are received from BCM via CAN commu-
nication. (With segment information display) C
SHIFT IND Status of shift position, detected from shift position signal received from TCM via
[P, R, N, D, 2, 1] CAN communication.
O/D OFF SW D
Status of overdrive control switch.
[On/Off]
REAR DEF SW
Status of defogger switch.
[On/Off] E
COMP F/B SIG A/C compressor activation condition that ECM judges according to the engine
[On/Off] coolant temperature and the acceleration degree.
PKB SW
Status of parking brake switch.
F
[On/Off]
BUCKLE SW
Status of seat belt buckle switch (driver side).
[On/Off] G
BRAKE SW
Status of stop lamp switch.
[On/Off]
BRAKE OIL SW H
Status of brake fluid level switch.
[On/Off]
ENTER SW
[On/Off] Status of (ENTER) switch.
I
SELECT SW
[On/Off] Status of (SELECT) switch.
PASS BUCKLE SW J
This item is displayed, but cannot be monitored.
[Off]
DISTANCE
Value of distance to empty calculated by combination meter.
[km]
K
Ambient temperature value converted from ambient sensor signal received from
ambient sensor.
OUTSIDE TEMP NOTE:
[C° or F°] This may not match with the temperature value indicated on the information dis- L
play. (Because the information display value is a corrected value from the ambient
sensor input value.)
FUEL LOW SIG Status of fuel level low warning signal to output to AV control unit via CAN com- M
[On/Off] munication.
Buzzer status (in the combination meter) is detected from the buzzer output signal
BUZZER
X received from each unit via CAN communication and the warning output condition
[On/Off]
of the combination meter.
WCS
Blinking status of ASCD or speed limiter set vehicle speed that is judged by the
ASCD SPD BLNK
ASCD status signal and speed limiter operation signal received from ECM via
[On/Off] O
CAN communication.
ASCD STATUS Display status of ASCD and speed limiter status display judged by the ASCD sta-
[Off, ASCD, CRUISE, SL ON, SL tus signal and speed limiter operation signal received from ECM via CAN commu-
SET] nication. P
ASCD or speed limiter set vehicle speed value that is judged by the ASCD status
ASCD REQ SPD
signal and speed limiter operation signal received from ECM via CAN communi-
[km/h or mph/Off]
cation.
AT STOP START IND Status of Stop/Start indicator lamp signal received from ECM via CAN communi-
[On, Off, BLINK1, BLINK2] cation.
WCS-29
DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >
MAIN
Display item [Unit] Description
SIGNALS
AT STOP START STS
Status of stop/start readiness signal received from ECM via CAN communication.
[On/Off]
AT STOP START SW
Status of Stop/Start indicator lamp.
[On/Off]
NOTE:
Some items are not available according to vehicle specification.
SPECIAL FUNCTION
Special menu
W/L ON HISTORY
• Stores histories when warning/indicator lamp is turned on.
• “W/L ON HISTORY” indicates the “TIME” when the warning/ indicator lamp is turned on.
• The “TIME” above is:
- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine
and waiting for 30 seconds.
- 1 - 39: The number of times the engine was restarted after the 0 condition.
- NO W/L ON HISTORY: Stores NO (0) turning on history of warning/indicator lamp.
NOTE:
• W/L ON HISTORY is not stored for approximately 30 seconds after the engine starts.
• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets
low.
Display Item
WCS-30
DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >
Display item Description
A
AIR PRES W/L This item is displayed, but cannot be monitored.
KEY G/Y W/L Lighting history of KEY warning lamp (Green/Yellow).
KEY R W/L This item is displayed, but cannot be monitored. B
KEY KNOB W/L This item is displayed, but cannot be monitored.
EPS W/L Lighting history of EPS warning lamp.
e-4WD W/L This item is displayed, but cannot be monitored. C
AFS OFF IND This item is displayed, but cannot be monitored.
4WAS/RAS W/L This item is displayed, but cannot be monitored.
D
DDS W/L This item is displayed, but cannot be monitored.
SYS FAIL W/L This item is displayed, but cannot be monitored.
SFT POSI W/L This item is displayed, but cannot be monitored. E
HV BAT W/L This item is displayed, but cannot be monitored.
HEV BRAKE W/L This item is displayed, but cannot be monitored.
F
SFT OPER W/L This item is displayed, but cannot be monitored.
LANE KEEP W/L This item is displayed, but cannot be monitored.
CHAGE W/L This item is displayed, but cannot be monitored. G
OIL LEV LOW This item is displayed, but cannot be monitored.
DPF W/L This item is displayed, but cannot be monitored.
H
TRAILER IND This item is displayed, but cannot be monitored.
RUN FLAT W/L This item is displayed, but cannot be monitored.
E-SUS W/L This item is displayed, but cannot be monitored. I
LAUNCH CNT W/L This item is displayed, but cannot be monitored.
BRAKE PAD W/L This item is displayed, but cannot be monitored.
J
WCS
WCS-31
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000005887677
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × × ×
Automatic air conditioner AIR CONDITONER × ×
• Intelligent Key system
INTELLIGENT KEY × × ×
• Engine start system
Combination switch COMB SW ×
Body control system BCM ×
NATS IMMU × × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Back door TRUNK ×
Vehicle security system THEFT ALM × × ×
— RETAINED PWR* ×
Signal buffer system SIGNAL BUFFER × ×
WCS-32
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION >
BUZZER WCS
O
APPLICATION ITEMS
DATA MONITOR
WCS-33
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION >
Display item
Description
[Unit]
PUSH SW
Status of push-button ignition switch judged by BCM.
[On/Off]
UNLK SEN-DR
Status of unlock sensor judged by BCM.
[On/Off]
VEH SPEED 1
Value of vehicle speed signal received from combination meter with CAN communication line.
[km/h]
TAIL LAMP SW
Status of lighting switch judged by BCM using the combination switch readout function.
[On/Off]
FR FOG SW
Status of front fog lamp switch judged by BCM using the combination switch readout function.
[On/Off]
DOOR SW-DR
Status of driver side door switch judged by BCM.
[On/Off]
CDL LOCK SW
Status of door lock unlock switch judged by BCM.
[On/Off]
ACTIVE TEST
Display item
Description
[Unit]
KEY REMINDER WARN The key warning chime operation can be checked by operating the relevant function (On/Off).
The seat belt reminder warning chime operation can be checked by operating the relevant function (On/
SEAT BELT WARN TEST
Off). (For Hong Kong)
LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off).
The reverse warning chime operation can be checked by operating the relevant function (On/Off). (For
REVERSE WARNING
Hong Kong)
WCS-34
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
A
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000006033917
B
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
C
Diagnosis mode Function Description
Work Support Changes the setting for each system function.
D
Self Diagnostic Result Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor Monitors the reception status of CAN communication viewed from BCM.
Data Monitor The BCM input/output signals are displayed. E
Active Test The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification The BCM part number is displayed.
• Read and save the vehicle specification. F
Configuration
• Write the vehicle specification when replacing BCM.
SYSTEM APPLICATION
G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item H
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
I
Door lock DOOR LOCK × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × × J
Interior room lamp control INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
K
• *1: For models without theft warning alarm this mode is not used.
• *2: This item is displayed, but is not used.
BUZZER
WCS-35
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION >
BUZZER : CONSULT Function (BCM - BUZZER) INFOID:0000000006033918
APPLICATION ITEMS
DATA MONITOR
Display item
Description
[Unit]
IGN ON SW
Status of ignition switch judged by BCM.
[On/Off]
KEY ON SW
Status of key switch judged by BCM.
[On/Off]
DOOR SW-DR
Status of driver side door switch judged by BCM.
[km/h]
REVERSE SW CAN
This item is displayed, but cannot be monitored.
[On/Off]
TAIL LAMP SW
Status of lighting switch judged by BCM using the combination switch readout function.
[On/Off]
FR FOG SW
Status of front fog lamp switch judged by BCM using the combination switch readout function.
[On/Off]
BUCKLE SW Status of seatbelt buckle switch (driver side) received from combination meter with CAN communica-
[On/Off] tion line.
VEHICLE SPEED
Value of vehicle speed signal received from combination meter with CAN communication line.
[km/h]
ACTIVE TEST
Display item
Description
[Unit]
IGN KEY WARN ALM The key warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off).
WCS-36
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
ECU DIAGNOSIS INFORMATION A
COMBINATION METER
Reference Value INFOID:0000000006844461
B
WCS-37
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Monitor Item Condition Value/Status
WCS-38
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Monitor Item Condition Value/Status
A
Ignition switch
Engine start operation indicator ON B&P N
LOCK or ACC
Ignition switch
Engine start operation indicator ON B&P I B
ON
Ignition switch
Engine start operation indicator ON C&P N
LOCK or ACC
Ignition switch C
Engine start operation indicator ON C&P I
ON
Ignition switch
ACC warning display LK WN
ON D
LCD
Ignition switch
Steering lock information display ROTAT
LOCK
Ignition switch E
Shift P warning lamp ON SFT P
LOCK
Ignition switch
KEY warning lamp blinking NO KY
ON F
Ignition switch
Key ID warning display ID NG
LOCK
Ignition switch G
Intelligent Key low battery warning display BATT
LOCK
Shift position indicator P display P
Shift position indicator R display R H
WCS-39
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Monitor Item Condition Value/Status
Input value of ambient sensor signal.
Ignition switch NOTE:
OUTSIDE TEMP —
ON This may not match the indicated value
on the information display.
JPNIA0968GB
WCS-40
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No. A
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
B
Ignition
1
Ground Battery power supply Input switch — Battery voltage
(R)
OFF
C
Ignition
3
Ground Ignition signal Input switch — Battery voltage
(GR)
ON
D
Ignition
4 26 E
Fuel level sensor signal Input switch —
(W) (GR)
ON
JSNIA2927ZZ
F
G
Speedometer operated
[When vehicle speed is ap-
prox. 20 km/h (12.5 MPH)]
H
JSNIA3084ZZ
JSNIA3085ZZ
K
Speedometer operated L
[When vehicle speed is ap-
prox. 60 km/h (37.5 MPH)]
M
JSNIA3086ZZ
8
— CAN-H — — — —
(L) WCS
10
— CAN-L — — — —
(P)
Ignition O
12 A/C auto amp. connection
Ground Input switch — 5V
(L) recognition signal
ON
WCS-41
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
14 Ignition
Engine coolant tempera- PKID0590E
(BR)*1 Ground Output switch
ture signal
(G)*2 ON
SKIB3651J
*3
15 — — — — — —
(GR)
Ignition
21
Ground Ground — switch — 0V
(B)
ON
Ignition
22
Ground Ground — switch — 0V
(B)
ON
Ignition
24 Ambient sensor signal
Ground — switch — 0V
(Y) ground
ON
Ignition 0 – 4.8 V
27 Changes depending to am-
Ground Ambient sensor signal Input switch Output voltage varies with ambi-
(R) bient temperature.
ON ent temperature
While pressing the over-
Ignition drive control or SPORT 0V
28 Overdrive control/SPORT
Ground Input switch mode switch.
(P) mode switch signal
ON
Other than the above 12 V
WCS-42
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value A
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition Charge warning lamp ON 2V B
35
Ground Alternator signal Input switch
(Y) Charge warning lamp OFF 12 V
ON
Terminal No.
Description H
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition
I
1
Ground Battery power supply Input switch — Battery voltage
(R)
OFF
Ignition Brake pedal is depressed 0V J
2
Ground Stop lamp switch signal Input switch
(LG) Other than the above Battery voltage
OFF
Ignition K
3
Ground Ignition signal Input switch — Battery voltage
(GR)
ON
Ignition
4 26
Fuel level sensor signal Input switch —
(W) (GR) M
ON
JSNIA2927ZZ
WCS
WCS-43
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Speedometer operated
[When vehicle speed is ap-
prox. 20 km/h (12.5 MPH)]
JSNIA3084ZZ
JSNIA3085ZZ
Speedometer operated
[When vehicle speed is ap-
prox. 60 km/h (37.5 MPH)]
JSNIA3086ZZ
8
— CAN-H — — — —
(L)
10
— CAN-L — — — —
(P)
Ignition
12 A/C auto amp. connection
Ground Input switch — 5V
(L) recognition signal
ON
Passenger air bag OFF in-
Ignition 3V
13 Passenger air bag OFF in- dicator lamp ON
Ground Input switch
(LG) dicator signal Passenger air bag OFF in-
ON 0V
dicator lamp OFF
14 Ignition
Engine coolant tempera- PKID0590E
(G)*1 Ground Output switch
ture signal
(BR)*2 ON
SKIB3651J
*3
15 — — — — — —
(GR)
WCS-44
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value A
Condition
Input/ (Approx.)
+ – Signal name
Output
NOTE: B
The maximum voltage varies de-
pending on the specification
(destination unit).
C
Ignition Speedometer operated
16 Vehicle speed signal
Ground Input switch [When vehicle speed is ap-
(L/B) (2-pulse)
ON prox. 40 km/h (25 MPH)]
D
JSNIA0015GB
E
NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit). F
17 Ignition Speedometer operated
Vehicle speed signal
(SB)*4 Ground Input switch [When vehicle speed is ap-
(8-pulse)
(P)*5 ON prox. 40 km/h (25 MPH)]
G
JSNIA0012GB H
18*3 — — — — — —
(G)
When all of below condi-
I
tions are met
• When driver door closed
• Tail lamps OFF condition J
[Refer to EXL-18,
"PARKING, LICENSE
PLATE AND TAIL LAMP
SYSTEM : System De-
9V
K
scription" (TYPE1) or
EXL-151, "PARKING, LI-
CENSE PLATE AND
TAIL LAMP SYSTEM : L
System Description"
(TYPE2). To identify ve-
hicle type, refer to EXL-7,
Ignition "Information".] M
19
Ground Step lamp control signal Input switch
(BR) When any of below condi-
ON
tions is met At the beginning of lighting
• When driver door opened WCS
• Tail lamps ON condition
[Refer to EXL-18,
"PARKING, LICENSE
PLATE AND TAIL LAMP O
SYSTEM : System De-
scription" (TYPE1) or JSNIA3812GB
EXL-151, "PARKING, LI- NOTE:
CENSE PLATE AND
P
(A) becomes shorter (average
TAIL LAMP SYSTEM : voltage decreases) with in-
System Description" creased luminance, and the volt-
(TYPE2). To identify ve- age becomes 0 V at maximum
hicle type, refer to EXL-7, luminance.
"Information".]
WCS-45
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Tail lamps OFF condition
Refer to EXL-18, "PARK-
ING, LICENSE PLATE AND
TAIL LAMP SYSTEM : Sys-
tem Description" (TYPE1)
or EXL-151, "PARKING, LI- 9V
CENSE PLATE AND TAIL
LAMP SYSTEM : System
Description" (TYPE2). To
identify vehicle type, refer
to EXL-7, "Information".
Ignition At the beginning of lighting
20
Ground Console lamp control signal Input switch
(SB) Tail lamps ON condition
ON
Refer to EXL-18, "PARK-
ING, LICENSE PLATE AND
TAIL LAMP SYSTEM : Sys-
tem Description" (TYPE1)
or EXL-151, "PARKING, LI-
CENSE PLATE AND TAIL JSNIA3812GB
WCS-46
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value A
Condition
Input/ (Approx.)
+ – Signal name
Output
When driver seat belt is fas- B
34 Ignition 12 V
Seat belt buckle switch sig- tened.
(BG)*1 Ground Input switch
nal (driver side) When driver seat belt is un-
(V)*2 ON 0V
fastened. C
Ignition Charge warning lamp ON 2V
35
Ground Alternator signal Input switch
(Y) Charge warning lamp OFF 12 V
ON D
Ignition Brake fluid level is normal 12 V
36 Brake fluid level switch sig-
Ground Input switch Brake fluid level is less than
(LG) nal 0V
ON low level E
Ignition Parking brake applied. 0V
37
Ground Parking brake switch signal Input switch
(SB) Parking brake released. 12 V
ON
F
G
Steering right
H
SKIB3827E
J
Steering left
K
SKIB3828E
WCS
WCS-47
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Steering right
SKIB3827E
Steering left
SKIB3828E
Ignition
40 Steering angle sensor sig- Steering wheel in neutral
Ground Input switch
(V) nal 3 position
ON
SKIB3829E
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition
1
Ground Battery power supply Input switch — Battery voltage
(R)
OFF
Ignition Brake pedal is depressed 0V
2
Ground Stop lamp switch signal Input switch
(LG) Other than the above Battery voltage
OFF
Ignition
3
Ground Ignition signal Input switch — Battery voltage
(GR)
ON
WCS-48
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value A
Condition
Input/ (Approx.)
+ – Signal name
Output
B
Ignition
4 26 C
Fuel level sensor signal Input switch —
(W) (GR)
ON
JSNIA2927ZZ D
Stop/start OFF switch indi-
Ignition 0V
7 Stop/start OFF switch indi- cator ON
Ground Input switch E
(L) cator signal Stop/start OFF switch indi-
ON 12 V
cator OFF
8
— CAN-H — — — —
(L) F
Ignition DEF switch ON 0V
9
Ground DEF position signal Input switch
(V) DEF switch OFF 12 V
ON G
10
— CAN-L — — — —
(P)
14 L
Ignition
*1 Engine coolant tempera- PKID0590E
(G) Ground Output switch
ture signal
(BR)*2 ON
M
Engine idling [Approximate-
ly 80°C (176°F)]
WCS
SKIB3651J
15*3 O
— — — — — —
(GR)
WCS-49
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit).
17 Ignition Speedometer operated
Vehicle speed signal
(SB)*4 Ground Input switch [When vehicle speed is ap-
(8-pulse)
(P)*5 ON prox. 40 km/h (25 MPH)]
JSNIA0012GB
18*3 — — — — — —
(G)
When all of below condi-
tions are met
• When driver door closed
• Tail lamps OFF condition
[Refer to EXL-18,
"PARKING, LICENSE
PLATE AND TAIL LAMP
SYSTEM : System De-
9V
scription" (TYPE1) or
EXL-151, "PARKING, LI-
CENSE PLATE AND
TAIL LAMP SYSTEM :
System Description"
(TYPE2). To identify ve-
hicle type, refer to EXL-7,
Ignition "Information".]
19
Ground Step lamp control signal Input switch
(BR) When any of below condi-
ON
tions is met At the beginning of lighting
• When driver door opened
• Tail lamps ON condition
[Refer to EXL-18,
"PARKING, LICENSE
PLATE AND TAIL LAMP
SYSTEM : System De-
scription" (TYPE1) or JSNIA3812GB
EXL-151, "PARKING, LI- NOTE:
CENSE PLATE AND (A) becomes shorter (average
TAIL LAMP SYSTEM : voltage decreases) with in-
System Description" creased luminance, and the volt-
(TYPE2). To identify ve- age becomes 0 V at maximum
hicle type, refer to EXL-7, luminance.
"Information".]
WCS-50
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value A
Condition
Input/ (Approx.)
+ – Signal name
Output
Tail lamps OFF condition B
Refer to EXL-18, "PARK-
ING, LICENSE PLATE AND
TAIL LAMP SYSTEM : Sys-
tem Description" (TYPE1)
C
or EXL-151, "PARKING, LI- 9V
CENSE PLATE AND TAIL
LAMP SYSTEM : System D
Description" (TYPE2). To
identify vehicle type, refer
to EXL-7, "Information".
Ignition At the beginning of lighting E
20
Ground Console lamp control signal Input switch
(SB) Tail lamps ON condition
ON
Refer to EXL-18, "PARK-
ING, LICENSE PLATE AND F
TAIL LAMP SYSTEM : Sys-
tem Description" (TYPE1)
or EXL-151, "PARKING, LI-
G
CENSE PLATE AND TAIL JSNIA3812GB
22
Ignition J
Ground Ground — switch — 0V
(B)
ON
Ignition K
24
Ground Ambient sensor ground — switch — 0V
(Y)
ON
Ignition 0 – 4.8 V
27 Changes depending to am- L
Ground Ambient sensor signal Input switch Output voltage varies with ambi-
(R) bient temperature.
ON ent temperature
WCS-51
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
When driver seat belt is fas-
Ignition 12 V
34 Seat belt buckle switch sig- tened.
Ground Input switch
(V) nal (driver side) When driver seat belt is un-
ON 0V
fastened.
Ignition Charge warning lamp ON 2V
35
Ground Alternator signal Input switch
(Y) Charge warning lamp OFF 12 V
ON
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition
1
Ground Battery power supply Input switch — Battery voltage
(R)
OFF
Ignition Brake pedal is depressed 0V
2
Ground Stop lamp switch signal Input switch
(LG) Other than the above Battery voltage
OFF
Ignition
3
Ground Ignition signal Input switch — Battery voltage
(GR)
ON
Ignition
4 26
Fuel level sensor signal Input switch —
(W) (GR)
ON
JSNIA2927ZZ
WCS-52
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value A
Condition
Input/ (Approx.)
+ – Signal name
Output
B
Speedometer operated
[When vehicle speed is ap- C
prox. 20 km/h (12.5 MPH)]
JSNIA3084ZZ D
E
Ignition Speedometer operated
6 25 Vehicle speed sensor sig-
Input switch [When vehicle speed is ap-
(L) (B) nal
ON prox. 40 km/h (25 MPH)]
F
JSNIA3085ZZ
Speedometer operated
[When vehicle speed is ap-
prox. 60 km/h (37.5 MPH)]
H
JSNIA3086ZZ
I
Stop/start OFF switch indi-
Ignition 0V
7 Stop/start OFF switch indi- cator ON
Ground Input switch
(L) cator signal Stop/start OFF switch indi-
ON 12 V J
cator OFF
8
— CAN-H — — — —
(L)
K
Ignition DEF switch ON 0V
9
Ground DEF position signal Input switch
(V) DEF switch OFF 12 V
ON
10
L
— CAN-L — — — —
(P)
Ignition
12 A/C auto amp. connection M
Ground Input switch — 5V
(L) recognition signal
ON
Passenger air bag OFF in-
Ignition 3V
13 Passenger air bag OFF in- dicator lamp ON WCS
Ground Input switch
(LG) dicator signal Passenger air bag OFF in-
ON 0V
dicator lamp OFF
O
WCS-53
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
14 Ignition
Engine coolant tempera- PKID0590E
(G)*1 Ground Output switch
ture signal
(BR)*2 ON
SKIB3651J
*3
15 — — — — — —
(GR)
NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit).
Ignition Speedometer operated
17 Vehicle speed signal
Ground Input switch [When vehicle speed is ap-
(SB) (8-pulse)
ON prox. 40 km/h (25 MPH)]
JSNIA0012GB
18*3 — — — — — —
(G)
WCS-54
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value A
Condition
Input/ (Approx.)
+ – Signal name
Output
When all of below condi- B
tions are met
• When driver door closed
• Tail lamps OFF condition
[Refer to EXL-18,
C
"PARKING, LICENSE
PLATE AND TAIL LAMP
SYSTEM : System De- D
9V
scription" (TYPE1) or
EXL-151, "PARKING, LI-
CENSE PLATE AND
TAIL LAMP SYSTEM : E
System Description"
(TYPE2). To identify ve-
hicle type, refer to EXL-7,
Ignition "Information".] F
19
Ground Step lamp control signal Input switch
(BR) When any of below condi-
ON
tions is met At the beginning of lighting
• When driver door opened G
• Tail lamps ON condition
[Refer to EXL-18,
"PARKING, LICENSE
PLATE AND TAIL LAMP H
SYSTEM : System De-
scription" (TYPE1) or JSNIA3812GB
EXL-151, "PARKING, LI- NOTE:
CENSE PLATE AND (A) becomes shorter (average
I
TAIL LAMP SYSTEM : voltage decreases) with in-
System Description" creased luminance, and the volt-
(TYPE2). To identify ve- age becomes 0 V at maximum
hicle type, refer to EXL-7,
J
luminance.
"Information".]
Tail lamps OFF condition
Refer to EXL-18, "PARK- K
ING, LICENSE PLATE AND
TAIL LAMP SYSTEM : Sys-
tem Description" (TYPE1)
or EXL-151, "PARKING, LI- 9V L
CENSE PLATE AND TAIL
LAMP SYSTEM : System
Description" (TYPE2). To
M
identify vehicle type, refer
to EXL-7, "Information".
Ignition At the beginning of lighting
20 WCS
Ground Console lamp control signal Input switch
(SB) Tail lamps ON condition
ON
Refer to EXL-18, "PARK-
ING, LICENSE PLATE AND
TAIL LAMP SYSTEM : Sys- O
tem Description" (TYPE1)
or EXL-151, "PARKING, LI-
CENSE PLATE AND TAIL JSNIA3812GB
WCS-55
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition
21
Ground Ground — switch — 0V
(B)
ON
Ignition
22
Ground Ground — switch — 0V
(B)
ON
Ignition
24
Ground Ambient sensor ground — switch — 0V
(Y)
ON
Ignition 0 – 4.8 V
27 Changes depending to am-
Ground Ambient sensor signal Input switch Output voltage varies with ambi-
(R) bient temperature.
ON ent temperature
While pressing the over-
Ignition drive control or SPORT 0V
28 Overdrive control/SPORT
Ground Input switch mode switch.
(P) mode switch signal
ON
Other than the above 12 V
WCS-56
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Function Specifications A
Speedometer (A/T or CVT models)
Reset to zero by suspending communication.
Tachometer
When suspending communication, changes to nighttime
B
Illumination control
mode.
Current fuel consumption 0 km/h is displayed.
C
Average fuel consumption • When reception time of an abnormal signal is 2 sec-
onds or less, the last received datum is used for cal-
Trip computer culation to indicate the result.
Distance to empty • When reception time of an abnormal signal is more D
Information dis- than 2 seconds, the last result calculated during nor-
play mal condition is indicated.
An indicated value is maintained at communications
Odo/trip meter E
blackout.
Shift position indicator The indicator turns OFF by suspending communication.
Engine start operation indicator The indicator turns OFF by suspending communication. F
Buzzer The buzzer turns off by suspending communication.
ABS warning lamp
EPS warning lamp G
Brake warning lamp (With ABS)
Malfunction indicator (MI) (yellow) or Malfunction indica- The lamp turns ON by suspending communication.
H
tor lamp (MIL) (yellow)
ESP OFF indicator lamp
SLIP indicator lamp I
High water temperature warning lamp
High beam indicator lamp
Turn signal indicator lamp J
Front fog lamp indicator lamp
Rear fog lamp indicator lamp
K
Warning lamp/in- Door warning lamp
dicator lamp
Shift P warning lamp
Key warning lamp L
Oil pressure warning lamp
The lamp turns OFF by suspending communication.
Stop/start indicator lamp
M
SPORT indicator lamp
OD OFF indicator lamp
Glow indicator lamp WCS
Malfunction indicator (MI) (Red)
Water-in-fuel-filter warning lamp
O
CRUISE indicator lamp
Speed limiter indicator lamp
SET indicator lamp P
WITH DOT MATRIX INFORMATION DISPLAY
The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.
Function Specifications
Speedometer
Reset to zero by suspending communication.
Tachometer
WCS-57
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Function Specifications
When suspending communication, changes to nighttime
Illumination control
mode.
Current fuel consumption • When reception time of an abnormal signal is 2 sec-
onds or less, the last received datum is used for cal-
Average fuel consumption
culation to indicate the result.
Average vehicle speed • When reception time of an abnormal signal is more
Trip computer than 2 seconds, the last result calculated during nor-
Distance to empty mal condition is indicated.
An indicated value is maintained at communications
Travel distance
blackout.
Door open warning
Interrupt indica-
Light reminder warning The indicator turns OFF by suspending communication.
tion
Seat belt reminder warning
An indicated value is maintained at communications
Accumulated time
blackout.
Current saved fuel consumption An indicated value is maintained at communications
(Except for HR12DDR) blackout.
• When reception time of an abnormal signal is 2 sec-
onds or less, the last received datum is used for cal-
Information dis- CO2 saved information culation to indicate the result.
play (HR12DDR) • When reception time of an abnormal signal is more
Idling stop dis- than 2 seconds, the last result calculated during nor-
play (with stop/ mal condition is indicated.
start system)
Engine stop guidance (HR12DDR)
Stop/start system off message
(HR12DDR) • When reception time of an abnormal signal is 2 sec-
onds or less, the last received datum is used to indi-
Stop/start system fault information cate the result.
(HR12DDR) • When reception time of an abnormal signal is more
Precautions on stop/start system in- than 2 seconds, the indicator turns OFF.
formation
(HR12DDR)
Parking sensor The indicator turns OFF by suspending communication.
Parking space measurement The indicator turns OFF by suspending communication.
An indicated value is maintained at communications
Odo/trip meter
blackout.
Shift position indicator The indicator turns OFF by suspending communication.
Engine start operation indicator The indicator turns OFF by suspending communication.
Buzzer The buzzer turns off by suspending communication.
WCS-58
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Function Specifications
A
ABS warning lamp
EPS warning lamp
Brake warning lamp B
Malfunction indicator (MI) (yellow) or Malfunction indica- The lamp turns ON by suspending communication.
tor lamp (MIL) (yellow)
ESP OFF indicator lamp C
SLIP indicator lamp
High water temperature warning lamp
D
Low water temperature indicator lamp
High beam indicator lamp
Warning lamp/in- Turn signal indicator lamp
dicator lamp
E
Front fog lamp indicator lamp
Rear fog lamp indicator lamp
Shift P warning lamp F
The lamp turns OFF by suspending communication.
Key warning lamp
Oil pressure warning lamp
G
Stop/start indicator lamp
SPORT indicator lamp
OD OFF indicator lamp H
CRUISE indicator lamp
Speed limiter indicator lamp
I
DTC Index INFOID:0000000006844463
J
Display contents of CONSULT Diagnostic item is detected when... Refer to
MWI-118,
CAN COMM CIRCUIT When combination meter is not transmitting or receiving CAN communication signal
"Diagnosis
[U1000] for 2 seconds or more. K
Procedure"
MWI-119,
CONTROL UNIT (CAN) When detecting error during the initial diagnosis of the CAN controller of combina-
"Diagnosis
[U1010] tion meter. L
Procedure"
• The abnormal vehicle speed signal is input from the ABS actuator and electric unit
MWI-120,
VEHICLE SPEED (control unit) for 2 seconds or more. (Models with ABS)
"Diagnosis
[B2205] • The abnormal vehicle speed signal is input from the TCM for 2 seconds or more.
Procedure"
M
(A/T models without ABS or CVT models without ABS)
MWI-121,
ENGINE SPEED If ECM continuously transmits abnormal engine speed signals for 2 seconds or
"Diagnosis WCS
[B2267] more.
Procedure"
MWI-122,
WATER TEMP If ECM continuously transmits abnormal engine coolant temperature signals for 60
"Diagnosis
[B2268] seconds or more. O
Procedure"
WCS-59
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
BCM (BODY CONTROL MODULE)
List of ECU Reference INFOID:0000000005887684
ECU Reference
WCS-60
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
WIRING DIAGRAM A
WARNING CHIME SYSTEM
TYPE A
B
TYPE A : Wiring Diagram INFOID:0000000006109673
NOTE: C
To identify destination of TYPE A, TYPE B, TYPE C and TYPE D, refer to MWI-4, "Information".
WCS
JCNWM4855GB
WCS-61
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
JCNWM4856GB
WCS-62
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
WCS
JCNWA3903GB
WCS-63
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
JCNWM4858GB
WCS-64
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
WCS
JCNWM4859GB
WCS-65
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
JCNWM4860GB
TYPE B
TYPE B : Wiring Diagram INFOID:0000000006882245
NOTE:
WCS-66
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
To identify destination of TYPE A, TYPE B, TYPE C and TYPE D, refer to MWI-4, "Information".
A
WCS
JCNWM5298GB
WCS-67
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
JCNWM5299GB
WCS-68
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
WCS
JCNWA3905GB
WCS-69
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
JCNWM5301GB
WCS-70
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
WCS
JCNWM5302GB
WCS-71
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
JCNWM5303GB
TYPE C
TYPE C : Wiring Diagram INFOID:0000000007195568
NOTE:
WCS-72
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
To identify destination of TYPE A, TYPE B, TYPE C and TYPE D, refer to MWI-4, "Information".
A
WCS
JCNWA4211GB
WCS-73
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
JCNWA4212GB
WCS-74
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
WCS
JCNWA4213GB
WCS-75
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
JCNWA4214GB
WCS-76
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
WCS
JCNWA4215GB
WCS-77
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
JCNWA4216GB
TYPE D
TYPE D : Wiring Diagram INFOID:0000000007479449
For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not
described in wiring diagram), refer to GI-12, "Connector Information".
NOTE:
WCS-78
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
To identify destination of TYPE A, TYPE B, TYPE C and TYPE D, refer to MWI-4, "Information".
A
WCS
JRNWC0693GB
WCS-79
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000005887687
OVERALL SEQUENCE
JSNIA4485GB
DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
>> GO TO 2.
2.CHECK SYMPTOM
• Check the symptom based on the information obtained from the customer.
• Check if any other malfunctions are present.
>> GO TO 3.
3.CHECK CONSULT SELF-DIAGNOSIS RESULTS
1. Connect CONSULT and perform self-diagnosis. Refer to WCS-59, "DTC Index".
WCS-80
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
2. When DTC is detected, follow the instructions below:
- Record DTC and Freeze Frame Data. A
Are self-diagnosis results normal?
YES >> GO TO 4.
NO >> GO TO 5. B
4.NARROW DOWN MALFUNCTIONING PARTS BY SYMPTOM DIAGNOSIS
Perform symptom diagnosis and narrow down the malfunctioning parts.
C
>> GO TO 5.
5.REPAIR OR REPLACE MALFUNCTIONING PARTS D
Repair or replace malfunctioning parts.
NOTE:
If DTC is displayed, erase DTC after repairing or replacing malfunctioning parts. E
>> GO TO 6.
F
6.FINAL CHECK
Check that the warning buzzer in the combination meter operates normally.
Does it operate normally? G
YES >> INSPECTION END
NO >> GO TO 1.
H
WCS
WCS-81
POWER SUPPLY AND GROUND CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
COMBINATION METER
COMBINATION METER : Diagnosis Procedure INFOID:0000000005904800
1.CHECK FUSE
Check for blown fuses.
Terminals
(+) (−) Voltage
Ignition switch position
Combination meter (Approx.)
Connector Terminal
Ground
1 OFF
M34 Battery voltage
3 ON
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check harness between combination meter and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between combination meter harness connector and ground.
Combination meter
Continuity
Connector Terminal
Ground
21
M34 Existed
22
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
WCS-82
METER BUZZER CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
METER BUZZER CIRCUIT
A
Component Function Check INFOID:0000000005887689
Select the “Data Monitor” for the “METER/M&A” and check the “BUZZER” monitor value.
E
BUZZER
Under the condition of buzzer input : On
Except above : Off
F
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-155, "Removal and Installation".
NO >> Replace BCM. Refer to BCS-199, "Removal and Installation" (with Intelligent Key system) or G
BCS-338, "Removal and Installation" (without Intelligent Key system).
Diagnosis Procedure INFOID:0000000005887690
H
1.CHECK POWER SUPPLY OF COMBINATION METER
Check power supply of combination meter. Refer to WCS-82, "COMBINATION METER : Diagnosis Proce-
dure". I
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair power supply circuit of combination meter. J
WCS
WCS-83
PARKING BRAKE SWITCH SIGNAL CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
PARKING BRAKE SWITCH SIGNAL CIRCUIT
Diagnosis Procedure INFOID:0000000005887691
(+) (−)
Voltage
Combination meter Condition
(Approx.)
Connector Terminal
Ground
Ignition When parking brake is applied 0V
M34 37
switch ON When parking brake is released 12 V
Is the inspection result normal?
YES >> INSPECTION END
NO >> GO TO 2.
2.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector and parking brake switch connector.
3. Check continuity between combination meter harness connector and parking brake switch harness con-
nector.
Terminals
Combination meter Parking brake switch Continuity
Connector Terminal Connector Terminal
M34 37 M11 1 Existed
4. Check continuity between combination meter harness connector and ground.
Terminals
Combination meter Continuity
Connector Terminal Ground
M34 37 Not existed
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
Component Inspection INFOID:0000000005887692
WCS-84
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS A
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
B
Description INFOID:0000000005887693
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is C
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
D
Diagnosis Procedure INFOID:0000000005887694
Perform check for the parking brake switch signal circuit. Refer to WCS-84, "Diagnosis Procedure".
Is the inspection result normal? I
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK PARKING BRAKE SWITCH J
Perform a unit check for the parking brake switch. Refer to WCS-84, "Component Inspection".
Is the inspection result normal?
K
YES >> Replace combination meter. Refer to MWI-155, "Removal and Installation"
NO >> Replace parking brake switch. Refer to PB-3, "Exploded View".
WCS
WCS-85
THE SEAT BELT REMINDER WARNING CONTINUES SOUNDING, OR DOES
NOT SOUND
< SYMPTOM DIAGNOSIS >
THE SEAT BELT REMINDER WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
Description INFOID:0000000006847426
WCS-86
THE SEAT BELT REMINDER WARNING CONTINUES SOUNDING, OR DOES
NOT SOUND
< SYMPTOM DIAGNOSIS >
WCS
WCS-87
THE LIGHT REMINDER WARNING DOES NOT SOUND
< SYMPTOM DIAGNOSIS >
THE LIGHT REMINDER WARNING DOES NOT SOUND
Description INFOID:0000000005887695
Light reminder warning chime does not sound even though headlamp is illuminated.
Diagnosis Procedure INFOID:0000000005887696
WCS-88
THE KEY WARNING DOES NOT SOUND (WITHOUT INTELLIGENT KEY)
< SYMPTOM DIAGNOSIS >
THE KEY WARNING DOES NOT SOUND (WITHOUT INTELLIGENT KEY)
A
Description INFOID:0000000005887699
The key warning chime does not sound, when all of the following conditions are fulfilled. B
• Key inserted into the key cylinder (key switch signal ON).
• Ignition switch is in ACC or OFF (ignition switch signal OFF).
• Driver side door is open (driver side door switch ON)
C
Diagnosis Procedure INFOID:0000000005887700
WCS
WCS-89
THE STOP/START SYSTEM REMINDER WARNING CHIME CONTINUES
SOUNDING, OR DOES NOT SOUND
< SYMPTOM DIAGNOSIS >
THE STOP/START SYSTEM REMINDER WARNING CHIME CONTINUES
SOUNDING, OR DOES NOT SOUND
Description INFOID:0000000007274998
CVT MODELS
1.CHECK STOP/START SYSTEM FUNCTION
Perform check for stop/start system function. Refer to EC3-1366, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace malfunctioning parts.
2.CHECK STOP/START INDICATOR SIGNAL CIRCUIT
Perform check for stop/start indicator signal circuit. Refer to EC3-1350, "Component Function Check".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace malfunctioning parts.
3.CHECK DRIVER SIDE DOOR SWITCH SIGNAL CIRCUIT
Perform the check for the driver side door switch signal circuit. Refer to DLK-114, "Diagnosis Procedure"
(TYPE 1), DLK-284, "Diagnosis Procedure" (TYPE 2), DLK-455, "Diagnosis Procedure" (TYPE 3), DLK-677,
"Diagnosis Procedure" (TYPE 4), DLK-832, "Diagnosis Procedure" (TYPE 5) or DLK-973, "Diagnosis Proce-
dure" (TYPE 6).
NOTE:
To identify vehicle type, refer to DLK-24, "Information".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair harness or connector.
4.CHECK DRIVER SIDE DOOR SWITCH
Perform a unit check for the driver side door switch. Refer to DLK-119, "Component Inspection" (TYPE 1),
DLK-290, "Component Inspection" (TYPE 2), DLK-458, "Component Inspection" (TYPE 3), DLK-680, "Com-
ponent Inspection" (TYPE 4), DLK-835, "Component Inspection" (TYPE 5) or DLK-976, "Component Inspec-
tion" (TYPE 6).
NOTE:
To identify vehicle type, refer to DLK-24, "Information".
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with intelligent models) or BCS-
338, "Removal and Installation" (without intelligent models).
NO >> Replace driver side door switch. Refer to DLK-233, "Removal and Installation" (TYPE 1), DLK-
378, "Removal and Installation" (TYPE 2), DLK-570, "Removal and Installation" (TYPE 3), DLK-
780, "Removal and Installation" (TYPE 4), DLK-925, "Removal and Installation" (TYPE 5) or DLK-
1057, "Removal and Installation" (TYPE 6). To identify vehicle type, refer to DLK-24, "Informa-
tion".
M/T MODELS
1.CHECK STOP/START SYSTEM FUNCTION
Perform check for stop/start system function. Refer to EC3-1366, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace malfunctioning parts.
WCS-90
THE STOP/START SYSTEM REMINDER WARNING CHIME CONTINUES
SOUNDING, OR DOES NOT SOUND
< SYMPTOM DIAGNOSIS >
2.CHECK STOP/START INDICATOR SIGNAL CIRCUIT A
Perform check for stop/start indicator signal circuit. Refer to EC3-1350, "Component Function Check".
Is the inspection result normal?
YES >> GO TO 3. B
NO >> Repair or replace malfunctioning parts.
3.CHECK SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT (DRIVER SIDE)
C
Perform check for seat belt buckle switch (driver side) circuit. Refer to MWI-133, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 4. D
NO >> Repair harness or connector.
4.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
Perform check for seat belt buckle switch (driver side). Refer to MWI-135, "Component Inspection". E
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace seat belt buckle (driver side). Refer to SB-12, "SEAT BELT BUCKLE : Removal and F
Installation".
5.CHECK DRIVER SIDE DOOR SWITCH SIGNAL CIRCUIT
G
Perform the check for the driver side door switch signal circuit. Refer to DLK-114, "Diagnosis Procedure"
(TYPE 1), DLK-284, "Diagnosis Procedure" (TYPE 2), DLK-455, "Diagnosis Procedure" (TYPE 3), DLK-677,
"Diagnosis Procedure" (TYPE 4), DLK-832, "Diagnosis Procedure" (TYPE 5) or DLK-973, "Diagnosis Proce-
dure" (TYPE 6). H
NOTE:
To identify vehicle type, refer to DLK-24, "Information".
Is the inspection result normal? I
YES >> GO TO 6.
NO >> Repair harness or connector.
6.CHECK DRIVER SIDE DOOR SWITCH J
Perform a unit check for the driver side door switch. Refer to DLK-119, "Component Inspection" (TYPE 1),
DLK-290, "Component Inspection" (TYPE 2), DLK-458, "Component Inspection" (TYPE 3), DLK-680, "Com-
ponent Inspection" (TYPE 4), DLK-835, "Component Inspection" (TYPE 5) or DLK-976, "Component Inspec- K
tion" (TYPE 6).
NOTE:
To identify vehicle type, refer to DLK-24, "Information". L
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-198, "Removal and Installation" (with intelligent models) or BCS-
338, "Removal and Installation" (without intelligent models). M
NO >> Replace driver side door switch. Refer to DLK-233, "Removal and Installation" (TYPE 1), DLK-
378, "Removal and Installation" (TYPE 2), DLK-570, "Removal and Installation" (TYPE 3), DLK-
780, "Removal and Installation" (TYPE 4), DLK-925, "Removal and Installation" (TYPE 5) or DLK- WCS
1057, "Removal and Installation" (TYPE 6). To identify vehicle type, refer to DLK-24, "Informa-
tion".
WCS-91