Professional Documents
Culture Documents
POWER INPUT
AC Power
76
(2.99) M: 85 – 264 V AC (Operational voltage range 85 – 264 V,
47 – 66 Hz)
124
(4.88)
[3] OPTIONS
mm (inch) blank: none
/Q: With options (specify the specification)
MODEL: M2LR-[1][2]-M[3]
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
ORDERING INFORMATION /C01: Silicone coating
• Code number: M2LR-[1][2]-M[3] /C02: Polyurethane coating
Specify a code from below for each [1] through [3]. /C03: Rubber coating
(e.g. M2LR-4Z1-M/Q) TERMINAL SCREW MATERIAL
• Temperature range (e.g. 0 – 100°C) /S01: Stainless steel
• Output range (e.g. 4 – 20 mA DC)
• Specify the specification for option code /Q
(e.g. /C01/S01)
RELATED PRODUCTS
• PC configurator software (model: M2LRCFG)
Downloadable at M-System’s web site.
[1] INPUT RTD (2- or 3-wire) A dedicated cable is required to connect the module to the
1: JPt 100 (JIS'89) PC. Please refer to the internet software download site or
(Usable range: -200 to +500°C, -328 to +932°F; min.span: 20°C, 36°F) the users manual for the PC configurator for applicable
3: Pt 100 (JIS'89) cable types.
(Usable range: -200 to +650°C, -328 to +1202°F; min.span: 20°C, 36°F)
4: Pt 100 (JIS'97, IEC)
(Usable range: -200 to +850°C, -328 to +1562°F; min.span: 20°C, 36°F)
GENERAL SPECIFICATIONS
Construction: Plug-in
5: Pt 50 Ω (JIS'81)
Connection: M3 screw terminals (torque 0.8 N·m)
(Usable range: -200 to +649°C, -328 to +1200°F; min.span: 20°C, 36°F)
Housing material: Flame-resistant resin (black)
7: Pt 1000
Isolation: Input to output to power
(Usable range: -200 to +850°C, -328 to +1562°F; min.span: 20°C, 36°F)
Overrange output: Approx. -15 to +115 %
9: Cu 10 @25°C
Zero adjustment: -15 to +15 % (front)
(Usable range: -50 to +250°C, -58 to +482°F; min.span: 20°C, 36°F)
Span adjustment: 85 to 115 % (front)
(Consult M-System for users’ tables.)
Burnout protection: Upscale, downscale or no burnout
(Input range are fully programmable out of the range
selectable with DIP switches
specified when ordering by setting up the DIP switch and
Status indicator LED: Tri-color (green/amber/red) LED;
using ‘One-Step-Cal’ Calibration. PC Configurator is also
Flashing patterns indicate operation status of the
LED3 (LD3)
1 2 3 4 5 6 7 8
ON
Configurator Jack
OFF
MODE Button
SW2
UP Button 1 2 3 4
ON SW1
DOWN Button
OFF
For detailed information on the configuration and calibration, refer to the instruction manual.
DIN RAIL
35mm wide 4 1
8 5
2–4.2x5
(.17x.20)
70.5 (2.78)
59 (2.32)
72 (2.83)
MTG HOLE
6 (.24) deep
8–M3 12 9
SCREW 14 13
STATUS CONTROL SW
2.5V DIP SW Isolation
RTD
Digital Output
A 5 Computation Driver
9 +
OUTPUT
Low Drift
B 1 12 –
Amplifier
B 8 13 U
2.5kΩ POWER
14 V
CONFIGURATOR JACK 4
Base Socket
Fixing Screw
■ PACKAGE INCLUDES:
Signal conditioner (body + base socket)....................... (1)
Connection
■ MODEL NO. Diagram
Confirm Model No. marking on the product to be exactly Specifications
what you ordered.
■ INSTRUCTION MANUAL
This manual describes necessary points of caution when INSTALLATION
you use this product, including installation, connection and
Loosen the fixing screw at the front of the unit in order to
basic maintenance procedures.
separate the body from the base socket.
The M2LR is programmable using the PC configurator soft-
ware. For detailed information on the PC configuration, re-
■ DIN RAIL MOUNTING
fer to the M2LRCFG instruction manual. The M2LRCFG
Set the base socket so that
PC Configurator Software is downloadable at M-System’s
its DIN rail adaptor is at
web site: http://www.m-system.co.jp.
the bottom. Position the
upper hook at the rear side DIN Rail
of base socket on the DIN 35mm wide
POINTS OF CAUTION rail and push in the lower.
■ POWER INPUT RATING & OPERATIONAL RANGE When removing the socket,
• Locate the power input rating marked on the product and push down the DIN rail
confirm its operational range as indicated below: adaptor utilizing a minus
85 – 264V AC rating: 85 – 264V, 47 – 66 Hz, approx. 4 – 6VA screwdriver and pull.
Spring Loaded
■ GENERAL PRECAUTIONS ■ WALL MOUNTING
DIN Rail Adaptor
• Before you remove the unit from its base socket or mount Refer to “EXTERNAL DI-
it, turn off the power supply and input signal for safety. MENSIONS.”
■ ENVIRONMENT
• Indoor use TERMINAL CONNECTIONS
• When heavy dust or metal particles are present in the air,
Connect the unit as in the diagram below.
install the unit inside proper housing with sufficient ven-
tilation.
• Do not install the unit where it is subjected to continuous RTD
A 5 9 +
vibration. Do not subject the unit to physical impact. OUTPUT
• Environmental temperature must be within -5 to +55°C B 1 12 –
(23 to 131°F) with relative humidity within 30 to 90% RH
B 8 13 U
in order to ensure adequate life span and operation. POWER
• Be sure that the ventilation slits are not covered with ca- CONFIGURATOR JACK 14 V
bles, etc.
■ WIRING
• Do not install cables (power supply, input and output)
close to noise sources (relay drive cable, high frequency
line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■ AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
EM-5057-A Rev.2 P. / 6
EXTERNAL VIEWS
■ FRONT VIEW ■ SIDE VIEW
LED1 (LD1)
LED3 (LD3)
1 2 3 4 5 6 7 8
ON
Configurator Jack
OFF
MODE Button
SW2
UP Button 1 2 3 4
ON SW1
DOWN Button
OFF
EM-5057-A Rev.2 P. / 6
B 1 12
B 8 13
AC Power Source
14
EM-5057-A Rev.2 P. / 6
POWER ON
LD3
DOWN R Red LED Blink
G
■ ZERO & SPAN ADJUSTMENTS Note 1: Calibration steps can be skipped when not needed
After the transmitter is installed and operational, fine zero by repeating pushing MODE buttons.
and span tuning can be performed as explained below. Both Note 2: There is no stated order of setting 0% and 100%
zero and span are adjustable within ±15%. levels or no limitation of entering values for multiple times
1) Run Mode: Confirm that the LD1 green light is blink- within one step of Calibration Mode. Signal level is stored
ing. each time the respective UP or DOWN button is pressed.
2) Fine Zero Calibration Mode: Press MODE button for 1
or 2 seconds until the LD1 red light is ON and the LD2
green light is blinking.
3) Use UP (increase) and DOWN (decrease) buttons to ad-
just the output to 0%.
4) Fine Span Calibration Mode: Push MODE button and
confirm that the LD3 green light instead of LD2 is blink-
ing.
5) Use UP (increase) and DOWN (decrease) buttons to ad-
just the output to 100%.
6) Run Mode: Push MODE button and confirm that only the
LD1 green light is blinking.
EM-5057-A Rev.2 P. / 6
G Green LED ON
ERROR MODE
LD1 LD1
Parameter Error Output Saturated in PC Configuration Mode
A G
LD2
Error occurred when reading parameters from the LD2
The output is below -15% or above +115%.
internal memory. Turn the power suppy off and on.
LD3 If the error still exists, reset the parameters to default LD3
and program the unit again. A
LD1 LD1
Communication Error Output Saturated in DIP SW Configuration Mode
*1 G
LD2
Internal CPU’s communication error. LD2
The output is below -15% or above +115%.
A
LD3 *1. LD1 may be one of the G G A . LD3
A
LD1 LD1
AD Conversion Error Burnout in PC Configuration Mode
*1 G
LD2
Internal AD conversion error. LD2
R
LD3 *1. LD1 may be one of the G G A . LD3
R
LD1 LD1
DIP SW Error Burnout in DIP SW Configuration Mode
R G
LD2
DIP SW configuration is inappropriate. LD2
R Check the DIP SW setting referring to Tables 2 – 10. R
LD3 LD3
R
EM-5057-A Rev.2 P. / 6
DIN RAIL
35mm wide 4 1
8 5
2–4.2x5
(.17x.20)
70.5 (2.78)
59 (2.32)
72 (2.83)
MTG HOLE
6 (.24) deep
8–M3 12 9
SCREW 14 13
4 (.16)
114 (4.49) [4 (.16)] 23 (.91)
M-SYSTEM WARRANTY
M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such
product was originally purchased if such product has been used under normal operating conditions and properly maintained, M-System’s sole liability, and purchaser’s exclusive
remedies, under this warranty are, at M-System’s option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this
warranty. To submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original
sales invoice.
THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR
SPECIAL DAMAGES OF ANY KIND WHATSOEVER.
M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: info@m-system.co.jp
EM-5057-A Rev.2 P. / 6