Professional Documents
Culture Documents
SL450 Dual Purpose Swivel Parts List
SL450 Dual Purpose Swivel Parts List
00
SL450 DUAL PURPOSE SWIVEL
PARTS LIST
SL001-TC
HONG HUA
I
I. SL001.00 SL450 DUAL PURPOSE SWIVEL GENERAL DRAWING
SL001.00 SL450 DUAL PURPOSE SWIVEL
1
2
SN Drawing No. Description Qty.
1 SL001.01 Bail ring 1
2 SL001.02 Screw plug: 2" 1
3 SL001.03.00 Gooseneck assembly 1
4 GB898-88 Stud bolt: AGM24-M24×65 24
5 GB6170-86 Nut: M24 24
6 GB93-87 Washer: 24 30
7 SL001.04 Upper cover 1
8 SL001.05.00 Packing device 1
9 SL001.06 Rubber umbrella 1
10 SL001.07 Upper liner 1
11 GB9877.1-88 Spring seal ring: B220×260×18 2
12 SL001.08 Distance ring 1
13 SL001.09 Snap ring for hole 1
14 GB297-94 32040 Bearing: 200×310×70 1
15 SL001.10 Adjusting gasket 1
16 GB5783-86 Bolt: M12×40 12
17 GB93-87 Washer: 12 12
18 SL001.11.00 Buffer device 3
19 GB5781-86 Bolt: M20×60 6
20 GB93-87 Washer: 20 6
21 GB97.1-85 Washer: 20 6
22 SL001.12 Gear ring: m=5 z=110 1
23 SL001.13 Central tube 1
24 GB67-85 Screw: M4×8 4
25 SL001.14 Mark plate 1
26 91754Q4 Bearing: 270×550×130 1
27 SL001.15 Housing 1
28 SL001.16 O-ring: 560×8.6 1
29 GB70-85 Screw: M24×65 6
30 GB283-94 NU1048 Bearing: 240×360×56 1
31 SL001.17 Bottom cover 1
32 SL001.18 Screw plug 1
33 SL001.19 Screw plug: M12×1.25 1
34 SL001.20 Rubber washer: 12×20 δ2 1
35 GB9877.1-88 Spring seal ring: B250×290×18 3
36 SL001.21 Distance ring 1
3
37 SL001.22 Clamp cover 1
38 GB70-85 Screw: M16×30 6
39 GB93-87 Washer: 16 6
40 SL001.23 Lower liner 1
41 SL001.24 O-ring: 155×8.6 1
42 SL001.25 Connector 1
43 SL001.26 Thread protector 1
44 GB1152-89 Oil cup: M10×1 1
45 SL001.27 Tube: 48×4 1
46 GB3289.37-82 Adjustable joint: Rc1 1/2" 1
47 SL001.28.00 Tube: 1 1/2" 1
48 GB812-88 Nut: M24×1.5 1
49 SL001.29 Connector 1
50 SL001.30.00 Connecting pipe 1
51 SL001.31.00 Connecting pipe 1
52 GB897-88 Stud bolt: AM16×65 2
53 GB897-88 Stud blot: AM16×100 3
54 GB6170-86 Nut: M16 5
55 SL001.32.00 Pneumatic motor and drive system 1
56 SL001.33 Inner connector 1
57 GB/T3452.1-92 O-ring: 120×5.3 1
58 SL001.34 Nut 1
59 SL001.35 O-ring: 165×8.6 1
60 SL001.36 Screw plug: 4" 1
61 SL001.37.00 Air system 1
62 SL001.38 Limiting board 1
63 GB3289.2-82 90°elbow: Rc1 1/2" 2
64 GB3289.26-82 Inner connector: R 1 1/2" 1
65 SL001.39.00 Oil level gauge 1
66 SL001.40 Limiting board 1
67 SL001.41 Spacer: 90×80 δ20 2
68 SL001.42 Bail pin 2
69 GB893.1-86 Retainer: 130 2
70 SL001.43 Dust cap: SR3×30 5
71 SL001.44.00 Sand break guard 1
4
II. PARTS DRAWING
1. SL001.03.00 Gooseneck assembly
5
2. SL001.05.00 Packing device
6
SN Drawing No. Description Qty.
1 SL001.05.01 Upper packing box pressure cover 1
2 SL001.05.02 Upper packing box 1
3 GB/T3452.1-92 O seal ring: 122×5.3 1
4 SL001.05.03 Upper gland 1
5 SL001.05.04 Mud packing 5
6 SL001.05.05 Upper bushing ring 1
7 SL001.05.06 Mud pipe 1
8 SL001.05.07 Spring ring 1
9 SL001.05.08 Lower bushing ring 1
10 SL001.05.09 Spacer 1
11 GB1152-89 Oil cup: M10×1 1
12 SL001.05.10 Lower packing box 1
13 SL001.05.11 Spacer 2
14 SL001.05.12 Lower O seal pressure sleeve 1
15 GB/T3452.1-92 O seal ring: 109×5.3 1
16 GB75-85 Screw: M10×12 1
17 SL001.05.13 Lower Packing Gland 1
7
3. SL001.30.00 Connecting tube
8
SN Drawing No. Description Qty.
1 SL001.30.01 Joint 2
2 SL001.30.02 Nut: M24×1.5 2
3 SL001.30.03 Connector core: M12×1.5 2
4 SL001.30.04 Nut: M12×1.25 2
5 A layer of steel braided hose: φ10-150×1m 1
9
4. SL001.31.00 Connecting tube
10
SN Drawing No. Description Qty.
1 SL001.31.01 Joint 1
2 SL001.30.02 Nut: M24×1.5 2
3 SL001.30.03 Connector core: M12×1.5 2
4 SL001.30.04 Nut: M12×1.25 2
5 A layer of steel braided hose: φ10-150×1m 1
11
5. SL001.32.00 Pneumatic motor and drive system
12
SN Drawing No. Description Qty.
1 FMS-20 type Pneumatic motor 1
2 GB3289-82 Inner connector: Rc2 1
3 GB3289-82 90°elbow: Rc2 1
4 GB5780-86 Bolt: M16×35 4
5 GB93-87 Washer: 16 4
6 SL001.32.01 Support 1
7 SL001.32.02 Small gear 1
8 GB894.1-86 retainer: 28 1
9 7010C GB/T292-94 Bearing: 50×80×16 1
10 GB/T3452.1-92 O-ring: 10.6×2.65 3
11 SL001.32.03 Separating plate 1
12 SL001.32.04 Felt ring: 5×50×62 1
13 51120 GB/T301-95 Bearing: 100×135×25 1
14 SL001.32.05 Connecting sleeve outer 1
15 SL001.32.06 Outside friction discⅠ 1
16 SL001.32.07 Outside friction disc Ⅱ 1
17 SL001.32.08 Outside friction discⅢ 1
18 SL001.32.09 Outside friction disc Ⅳ 1
19 SL001.32.10 Outside friction disc Ⅴ 1
20 SL001.32.11 Internal friction disc Ⅰ 2
21 SL001.32.12 Internal friction disc Ⅱ 2
22 SL001.32.13 Internal friction disc Ⅲ 2
23 SL001.32.14 Inner connecting sleeve 1
24 SL001.32.15 Sleeve 1
25 GB893.1-86 Retainer ring: 75 1
26 6009 GB/T276-94 Bearing: 45×75×16 1
27 SL001.32.16 Spring 10
28 51118 GB/T301-95 Bearing: 90×120×22 1
29 SL001.32.17 Spring seat 1
30 SL001.32.18 Plug 1
31 SL001.32.19 Clutch shell 1
32 SL001.32.20 O-ring: 175×8.6 1
33 GB/T3452.1-92 O-ring: 180×3.55 1
34 SL001.32.21 Clamp ring 1
35 SL001.32.22 Piston 1
36 GB/T3452.1-92 O-ring: 100×5.3 1
13
37 SL001.32.23 Cover 1
38 GB893.1-86 Retainer ring: 90 1
39 NU2210EGB/T283-94 Bearing: 50×90×23 1
40 SL001.32.24 Gear shaft: m=5 z=12 1
41 GB5783-86 Bolt: M12×30 8
42 SL001.32.25 Pin 2
43 SL001.32.26 Adjusting gasket 1
44 GB1096-90 Flat key: 14×28 1
45 SL001.32.27 Retainer ring: 60 1
46 GB32.1-88 Bolt: M8×16 2
47 SL001.32.28 Iron wire: φ1×100 1
48 GB70-85 Screw: M12×25 8
49 GB93-87 Washer: 12 20
50 GB1096-90 Flat key: 14×36 1
51 SL001.32.29 Gear: m=3 z=53 1
52 SL001.32.30 Round nut: M48×1.5 1
53 GB858-88 Washer: 48 1
54 GB893.1-86 Retainer ring: 72 1
55 NU207EGB/T283-84 Bearing: 35×72×17 1
56 SL001.28.03 Tube: 48×4 1
57 GB898-88 Bolt: M12×30 4
58 GB6170-86 Nut: M12 4
59 GB5780-86 Bolt: M12×110 2
60 Air collector 1
61 SL001.32.31 Connector: 10-R1/4 2
62 GB/T3452.1-92 O-ring: 53×3.55 4
14
6. SL001.37.00 Air system
15
SN Drawing No. Description Qty.
1 SL001.37.01.00 Frame 1
2 SL001.37.02 Right-angle joint 1
3 2+2 Gear air switch 1
4 GB3289-82 Inner joint: Rc1/4 1
5 GB3289-82 90°elbow: R1/4" 1
6 SL001.37.03 Joint: 1/4" M24×1.5 7
7 SL001.30.02 Nut: M24×1.5 10
8 SL001.30.03 Connector core: M12×1.25 10
9 SL001.30.04 Nut: M12×1.25 10
10 A layer of steel braided hose: φ10-150×32 m 1
11 A layer of steel braided tube: φ10-150×0.35m 1
12 A layer of steel braided tube: φ10-150×3.5m 1
13 A layer of steel braided tube: φ10-150×15m 1
14 SL001.37.04 Tube: R1/4×125 1
15 GB3289-82 T-joint: Rc1/4 1
16 SL001.37.05 Mark plate 1
17 GB67-85 Screw: M8×12-Q 4
18 GB93-87 Washer: 8 12
19 SL001.37.06 Board 1
20 SL001.37.07 Mark plate 1
21 GB/T5781-86 Bolt: M6×12 6
22 GB93-87 Washer: 6 6
23 Air rubber hose insertion cloth: φ45-10×18M 1
24 SL001.37.08 Dual pipe clamp 12
25 SL001.37.09 Dual pipe clamp 10
26 GB/T5781-86 Bolt: M8×30-Q 33
27 GB41-86 Nut: M8 45
28 SL001.37.10 Connector body 1
29 GB/T3452.1-92 O-ring: 13.2×1.8 1
30 QF23JQ-L40 Two-position three-way pneumatic valve: G1 1/2" 1
31 SL001.37.11 Pipe: φ48×4 2
32 QIU-40-SI Oil sprayer 1
33 QSL-40 Water and air separator 1
34 SL001.37.12 Pipe: R1 1/2"×70 5
35 J11T-16 Cut-off valve: Dg40 (1 1/2") 1
36 Air rubber hose insertion cloth: φ45-10×10m 1
16
37 Throat clamp: NO.3 12
38 SL001.27 Pipe: φ48×4 3
39 GB3289-82 90°elbow: Rc1 1/2" 2
40 SL001.37.13 U bolt: M8 2
41 SL001.37.14 U bolt: M16 4
42 GB97.1-85 Washer: 16 10
43 GB93-87 Washer: 16 10
44 GB41-86 Nut: M16 10
45 SL001.37.15 Baseplate 1
46 SL001.37.16.00 Connecting board 1
47 Air rubber hose insertion cloth: φ45-10×16m 1
48 A layer of steel braided hose: φ10-150×18m 1
49 Angle steel: 36×36×4 1
50 Angle steel: 36×36×4 1
51 GB3289.28-82 Internal & external screw: R3/4×Rc1/4 1
52 GB3289.14-82 Reducer tee: Rc1 1/2×1 1/2×3/4 1
53 JB/ZQ4492-86 Single pipe clamp: 48 2
54 Support 2
55 GB5781-86 Bolt: M8×20 8
17
7. SL001.39.00 Oil level gauge
18