Professional Documents
Culture Documents
Technical Publication: Direction 5271109-100 Revision 1 GE Healthcare Definium AMX 700 RJ45 Connector Upgrade
Technical Publication: Direction 5271109-100 Revision 1 GE Healthcare Definium AMX 700 RJ45 Connector Upgrade
gehealthcare.com
Technical
Publication
Direction 5271109-100
Revision 1
GE Healthcare
Definium AMX 700 RJ45 Connector Upgrade
Page 2
GE HEALTHCARE DEFINIUM AMX 700 RJ45 CONNECTOR UPGRADE
REVISION 1 DIRECTION 5271109-100
Revision History
Parts Description
5269080 AMX 700 RJ45 Kit
5271109-100 Definium AMX 700 RJ45 Upgrade (this document)
Figure 1
3.) Remove the Tether from the front bulkhead by pulling the Tether to the right until it is clear of
the front bulkhead.
Page 5
GE HEALTHCARE DEFINIUM AMX 700 RJ45 CONNECTOR UPGRADE
REVISION 1 DIRECTION 5271109-100
4.) Remove the Internal Ethernet Connection from the front bulkhead by depressing the thumb clip
and gently pulling the cable out of the receptacle. See Figure 2.
Figure 2
5.) Remove Nut "E" using a 3/8" nut driver. See Figure 2.
6.) Remove Screw "F" Qty 2 (See Figure 1) using a 5/32" allen wrench.
7.) Remove Bolt "B" Qty 2 (See Figure 1) using a 5/16" nut driver.
8.) Remove Nut "D" Qty 2 (See Figure 2) and Screw "A" Qty 2 (See Figure 1) using a 7/32" nut
driver and a Phillips screwdriver.
9.) Once Nut "D" Qty 2 and Screw "A" Qty 2 are removed, remove the Internal USB Cable from
the Front Bulkhead. See Figure 2.
10.) Remove the old Front Bulkhead from the assembly. See Figure 3.
Figure 3
Page 6
GE HEALTHCARE DEFINIUM AMX 700 RJ45 CONNECTOR UPGRADE
REVISION 1 DIRECTION 5271109-100
Figure 4
3.) Install the Internal USB Cable by inserting Screw "A" Qty 2 (See Figure 5) into the Front
Bulkhead and through the Internal USB Cable’s screw holes.
Figure 5
4.) Install Nut "D" Qty 2 (See Figure 4) onto Screw "A" Qty 2 (See Figure 5) with a 7/32" nut driver.
Page 7
GE HEALTHCARE DEFINIUM AMX 700 RJ45 CONNECTOR UPGRADE
REVISION 1 DIRECTION 5271109-100
5.) Install the Internal Ethernet Connection by sliding the end of the Internal Ethernet Connection
into the receptacle on the RJ connector housing. See Figure 4.
6.) Install Bolt "B" Qty 2 using a 5/16" nut driver. See Figure 5.
7.) Install Screw "F" Qty 2 using a 5/32" allen wrench. Make sure to first put the screws through
the cord guide then into the Front Bulkhead assembly. See Figure 5.
Figure 6
8.) Place the Tether Retainer Bracket on Screw "F" as shown in Figure 6.
9.) Install Nut "E" Qty 2 on Screw "F" Qty 2 using a 3/8" nut driver. See Figure 6.
10.) Slide the Tether into the slot in the Front Bulkhead. Make sure that the side of the Front
Bulkhead slides into the groove on the Tether. See Figure 7.
Figure 7
11.) Rotate the Tether Retainer Bracket up until it secures the Tether.
Page 8
GE HEALTHCARE DEFINIUM AMX 700 RJ45 CONNECTOR UPGRADE
REVISION 1 DIRECTION 5271109-100
12.) Install Screw "C" (See Figure 8) into Hole "G" (See Figure 7) using a Phillips screwdriver.
Figure 8
Figure 9
Page 9
GE HEALTHCARE DEFINIUM AMX 700 RJ45 CONNECTOR UPGRADE
REVISION 1 DIRECTION 5271109-100
Page 10
GE HEALTHCARE
34