Professional Documents
Culture Documents
EQUIPMENT LIST
ROTORCRAFT
ODA-240087-CE
Document Number:
005-01095-41 Rev. 6
CONFIDENTIAL
This drawing and the specifications contained herein are the property of Garmin International, Inc., or its subsidiaries and may
not be reproduced or used in whole or in part as the basis for manufacture or sale of products without written permission.
Table of Tables
Table 2-1: GMC 605H Mode Controller ....................................................................................... 2
Table 2-2: GFS 83 Force Servos................................................................................................. 2
Table 2-3: Collective Position Sensor ......................................................................................... 2
Table 2-4: Switches ..................................................................................................................... 2
Table 2-5: Mechanical Components ............................................................................................ 3
Table 2-6: GFS 83 Force Servo .................................................................................................. 4
Table 2-7: Mechanical Components ............................................................................................ 4
Table 2-8: Switches ..................................................................................................................... 4
Table 2-9: GFC 600H Loader Image ........................................................................................... 5
Table 2-10: GFC 600H BELL 505 Required Software ................................................................ 5
Table 2-11: GIFD (Legacy) Loader Images ................................................................................. 6
Table 2-12: GIFD (NXi v23.00) Loader Images........................................................................... 6
Table 2-13: GIFD (NXi v24.00) Loader Images........................................................................... 6
Table 2-14: ADAHRS Sensors Required Software .................................................................... 7
Page ii
1. INTRODUCTION
1.1 Purpose
This document provides a list of required and optional equipment for the GFC 600H Bell 505 STC,
SR01961WI.
Page 1
2. EQUIPMENT LIST
Page 2
Table 2-5: Mechanical Components
Page 3
2.1.2 Optional Equipment
The equipment approved for the optional installation of the yaw control is shown in this section.
Table 2-6: GFS 83 Force Servo
Catalog Mod Status
Description Part Number Qty
Part Number Revision
GFS 83 Servo, Clutchless High Torque, Servo 011-03367-14 010-01243-14 1 None
Connector Kit, GFS 83 (size 19) 011-03504-10 -- 1 A
Page 4
2.1.3 GFC 600H Required Software
Table 2-9: GFC 600H Loader Image
Description Software P/N Version
Software Loader Image, GFC 600H, Bell 505 006-B4031-00 403100
After loading software, the software loader image version number is shown in the lower right corner of
the GMC 605H start-up page as V403100.
Table 2-10: GFC 600H BELL 505 Required Software
Page 5
SYS 006-B1911-0D 2.05.1
GAIN 006-D8916-00 2.00
YAW MON BBL* 006-B1911-BF 2.03
RGN* 006-D4893-04 2.01
GFS 83,
Refer to Table KEY* 006-D7259-K0 2.00
Yaw Servo
2-6 SYS 006-B1911-0D 2.05.1
(If Installed)
GAIN 006-D8916-00 2.00
YAW CTL BBL* 006-B1911-BF 2.03
RGN* 006-D4893-04 2.01
KEY* 006-D7259-K0 2.00
*Software not loaded by the GFC 600H Loader Image
To interface the GFC 600H system with the Garmin Integrated Flight Deck (GIFD), a system option
loader card is required. Depending on the Bell TC approved software loader card, a specific option
loader card will be required. The GFC option loader card required for a given TC approved loader card is
shown with the appropriate TC loader card. The Bell 505 G1000H Legacy system must use the Bell TC
(R00008RD) approved software loader shown in Table 2-11 in accordance with the Bell Technical
Bulletin 505-TB-20-23, Garmin G1000H Software 006-B2472-02, Introduction of, prior to using the
G1000 (Legacy) GFC 600H STC Option Loader Card in Table 2-11.
Table 2-11: GIFD (Legacy) Loader Images
Description Software P/N
SW, G1000, Bell 505 v3.00 006-B2472-02
SW, G1000, Bell 505 GFC600H STC 006-B3859-00
The Bell 505 G1000H NXi system with release v23.00 must use the Bell TC (R00008RD) approved
software loader shown in Table 2-12. The Bell 505 G1000H NXi system with v23.00 must use the G1000
(NXi v23.00) GFC 600H STC Option Loader Card in Table 2-12 to load the required GSU 75H ADAHRS
software in Table 2-14.
Table 2-12: GIFD (NXi v23.00) Loader Images
Description Software P/N
SW, G1000 NXi, Bell 505 v23.00 006-B2472-23
SW, G1000 NXi, Bell 505 GFC600H STC 006-B4126-00
The Bell 505 G1000H NXi system with release v24.00 must use the Bell TC (R00008RD) approved
software loader shown in Table 2-13 in accordance with the Bell Information Letter IL-505-22-19. The
Bell 505 G1000H NXi system must use the G1000 (NXi v24.00) GFC 600H STC Option Loader Card in
Table 2-13.
Table 2-13: GIFD (NXi v24.00) Loader Images
Description Software P/N
SW, G1000 NXi, Bell 505 v24.00 006-B2472-24
SW, G1000 NXi, Bell 505 GFC600H STC, SW24 006-B4126-01
Page 6
The required software versions for the pre-existing GSU 75H ADAHRS sensors are shown in Table 2-14.
Verification of loaded software part numbers and versions for the LRUs listed in Table 2-14 is performed
on the GIFD GDU.
Table 2-14: ADAHRS Sensors Required Software
Page 7