Professional Documents
Culture Documents
DM100 Module
DM100 Module
DM-100
Installation manual
DM100.doc
V1110
Delem
Preface
This manual contains information necessary for installation of Delem DM-100 modules on a
pressbrake control system. It is meant for service people who are authorised for service and
installation of the machine.
Limited guarantee
• The equipment is supplied by Delem without safety features. The machine manufacturer has
to ensure a safe environment.
• This equipment must be installed and used in accordance with Delem's specifications. The
guarantee on the equipment is invalidated in the event of improper installation and/or use of
this equipment.
• The General Terms and Conditions of Delivery of Delem shall apply to this product. These
conditions are available from Delem on request.
• This manual does not entitle you to any rights. Delem reserves the right to change this
manual without prior warning.
• All rights reserved. The copyright is held by Delem. No part of this publication may be
copied or reproduced without written permission from Delem BV.
V1110, 2
Delem
Table of contents
V1110, 3
Delem
1. General information
1.1. Introduction
Front-end - max. 8
Control - max. 30m
DAonWindows
HSB-link Terminator R
DM DM DM DM
module module module module
Figure 1.a
V1110, 4
Delem
The following environment specification values are valid for all DM-modules:
For ventilation purposes, the module should have a free air space of 50 mm above and below the
mounted module and 10 mm on each side.
50 mm
DM-module
10 mm 10 mm
50 mm
V1110, 5
Delem
2. Connector specifications
2.1. Introduction
programmable I/O
digital I/O
digital I/O
Status
Analog B
display
Valve
Encoder 1
power supply
24V DC
Analog A Encoder 2
HSB
Encoder 3
HSB
Figure 2.a
Not all connectors are available on each module. For each connector is mentioned on which
modules it is implemented. See also chapter 3.
This chapter will focus on the specification of all available connectors.
See also drawing 9084-502 for an overview of the DM-100 series. This drawing is included in
the back of this manual.
V1110, 6
Delem
The ‘power’ connector is meant for the power supply for the module only.
The I/O systems (valve, analog and digital I/O) have their own power supply connectors. It is
recommended to connect the I/O systems to a different power supply.
power power
supply supply
module I/O
24V
power
0V
V1110, 7
Delem
not on DM-101
Figure 2.b
The use of I/O pins depends on the application and machine settings. For the purpose of all
assigned I/O signals we refer to the Delem machine parameter manual.
Notes:
• The sum of all output currents of the module shall not exceed 8A.
• All digital outputs are short-circuit proof.
• Shielding of I/O cables should be connected to the available M3 ground plug on the front of
the module.
Pins 1 - 8
Pins 9 - 16
V1110, 8
Delem
Programmable Digital In-/Outputs (8x):
Pins 17 - 24
V1110, 9
Delem
2.4. Valve
An example of the required wiring for direct valve control is given in drawing number 8576-
101.
The position feedback from the valve transducers (LVDT) is connected to connector Analog B.
V1110, 10
Delem
If no direct valve control is implemented but external valve amplifiers are used instead, the
valve connection block is not used. All analog signals for the valve amplifiers run through
connector Analog B. See section 2.6 for more information about this connector.
Analogue outputs:
Analogue inputs:
Shielding of cables should be connected to the available M3 ground plug on the front of the
module.
V1110, 11
Delem
2.5. Analog A
V1110, 12
Delem
2.6. Analog B
V1110, 13
Delem
Specifications for Analog I/O
Notes:
• Used power supply depends on transducer specifications (+/-12V or 24V).
• If necessary, shielding of cables can be connected to the available M3 ground plug on the
front of the module.
V1110, 14
Delem
2.7. Encoders
Notes:
• In case of 12VSE encoder, connect pins 6, 7, 8 and 9 with eachother.
• If necessary, shielding of cables can be connected to the available M3 ground plug on the
front of the module.
V1110, 15
Delem
The total length of the bus (the sum of all connections between modules) may not exceed 30
metres.
Maximal eight modules may be connected to one HSB-bus.
The HSB line must be closed with a termination resistor of 120 ohm.
Front-end - max. 8
Control - max. 30m
DAonWindows
HSB-link Terminator R
DM DM DM DM
module module module module
Figure 2.c
V1110, 16
Delem
3. The modules
3.1. Introduction
In this chapter all DM-100 modules are mentioned with their appearance and features.
Connector specifications are listed in chapter 2.
The following table gives an overview of the modules and available connectors.
V1110, 17
Delem
3.2. DM-103VA
The DM-103VA is designed for synchronised control of a Y-axis and one servo axis (the X-
axis).
programmable I/O
I/O
I/O
Status
Analog B
display
Valve
connections
Encoder 1
24V DC
Analog A Encoder 2
HSB
Encoder 3
HSB
Figure 3.a
For a wiring example of the module, reference is made to the following drawing:
• 8576-101 example connections DM-103VA
V1110, 18
Delem
3.3. DM-102VA
programmable I/O
I/O
I/O
Status
Analog B
display
Valve
connections
Encoder 1
24V DC
Analog A Encoder 2
HSB
HSB
Figure 3.b
For wiring example of the module, reference is made to the following drawing:
• 8562-101 example connections DM-102VA
V1110, 19
Delem
3.4. DM-102
The DM-102 can control 2 axes. It is designed for control of two servo or AC axes.
programmable I/O
I/O
I/O
Status
display
Encoder 1
24V DC
Analog A Encoder 2
HSB
HSB
Figure 3.c
For wiring example of the module, reference is made to the following drawing:
• 8562-109 example connections DM-102
V1110, 20
Delem
3.5. DM-101
The DM-101 can control 1 axis. It is designed for control of a servo or AC axis.
I/O
Status
display
Encoder 1
24V DC
Analog A
HSB
HSB
Figure 3.d
For example wiring of the module, reference is made to the following drawing:
• 8575-101 example connections DM-101
V1110, 21
Delem
3.6. DM-104
The DM-104 is an I/O expansion module. It does not control any axis.
Programmable I/O
I/O I/O
Status
display
24V DC
Analog A
HSB
HSB
Figure 3.e
For example wiring of the module, reference is made to the following drawing:
• 8577-101 example connections DM-104
V1110, 22
Delem
4.1. DM identification
Every module must be installed with and identified via the connected front-end control. The
identification takes place via the machine parameters menu.
Note: The connected modules must get their power supply within 1 second after switching
on the main box for correct communication and initialising.
In the first two columns, you must choose the module type and the ID number of the correct
module. In the two following columns, the version numbers of hardware and software of the
module are shown.
The last four columns are reserved for the axes names. This is described in the following
sections.
V1110, 23
Delem
4.2. DM-103VA
Since the DM-103VA is meant for Y-axis control, it will normally be configured as shown
above: Y-X-CROWN. Whether or not crowning is configured depends on the application.
If necessary, an FD axis could be added. Then the configuration would be Y-X-CROWN-FD.
Consider the number of available outputs.
The DM-103VA is not suitable to drive three servo/AC axes, for instance X1-X2-R.
4.3. DM-102VA
Since the DM-102VA is meant for Y-axis control, it will normally be configured as shown
above: Y-CROWN. The X-axis will have to be configured on a separate module.
It is possible to add an FD axis to this configuration if required.
4.4. DM-102
The DM-102 can drive two separate servo/AC axes. In the first column the left part of the
module is assigned, in the second column the right part. This is repeated for the third and the
fourth column. The configuration shown above is correct.
If column 1 and 2 are already assigned to two servo/AC axes, column 3 and 4 can no longer be
assigned to additional axes of that type. But it would be allowed to program two servo axes and
one digital axis on a module. Let’s look at some examples:
V1110, 24
Delem
Correct. When the digital axis (FD or ID) is installed, the control will issue a warning that there
is already an axis installed on the relevant module segment, but you are allowed to accept the
definition.
If one segment must drive an AC axis and a digital axis, you should check your sequencer to
prevent I/O conflicts between the two axes.
Incorrect. A DM-102 consists of two segments, each of which can drive one positioning axis
(servo or AC). If you try to configure this, the control will issue the same warning. In this case it
should not be accepted.
Incorrect. This is an attempt to assign two positioning axes to the left module segment.
V1110, 25
Delem
4.5. DM-101
The DM-101 is meant for control of one servo/AC axis, so the configuration shown above is
correct. If necessary, an FD axis can be added.
4.6. DM-104
.
The DM-104 is meant to expand the number of digital inputs and outputs. In the configuration
IO1, IO2, IO3 or IO4 should be configured
V1110, 26
Delem
The DM-100 module contains a 7-segment display that can show error and status codes.
- the module hardware initialisation (‘bootrom’): the decimal point is lit continuously
- the module software: the decimal point is off
- the diagnostic program: the decimal point is flashing
If a problem occurs and the display shows a character, write it down. Then check the following
table for an explanation of the message code. If an error persists, write down the number of the
error and contact Delem. Refer to the module type, the module software version and the error
number.
Bootrom messages:
Msg Description
A. - Assert (fatal error: switch module off/on)
V1110, 27
Delem
u. - Software update in progress.
b. - Boot start.
L. - VaLidate application.
P. - Start aPplication.
Software messages:
Message Description
A - Assert (fatal error: switch module off/on)
150?: ??????
1501.Tracking error margin exceeded
V1110, 28
Delem
2024. Encoder signal error on encoder 2.
2025. Overcurrent detected on valve outputs.
2028. Encoder signal error on encoder 3.
2029. Encoder signal error on encoder 4.
208?:FDC errors
2082. Error downloading deflection compensation table.
The ‘?’ can be any digit. If the error persists, write down the number of the error
and contact Delem. Refer to the module type, the module software version and
the error number.
- - Module started
V1110, 29
Delem
8/. - Diagnostic mode entered
V1110, 30
24V 24V 24V 24V 24V 24V 24V 24V 24V 24V 24V 24V 24V
1 1 9 17 1 9 17 1 9 17 1 9 17
2 2 10 18 2 10 18 2 10 18 2 10 18
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
3 3 11 19 3 11 19 3 11 19 3 11 19
4 4 12 20 4 12 20 4 12 20 4 12 20
5 5 13 21 5 13 21 5 13 21 5 13 21
IN / OUT
IN / OUT
IN / OUT
IN / OUT
6 6 14 22 6 14 22 6 14 22 6 14 22
IN
IN
IN
IN
IN
IN
IN
IN
IN
7 7 15 23 7 15 23 7 15 23 7 15 23
8 8 16 24 8 16 24 8 16 24 8 16 24
0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V
STATUS
STATUS
STATUS
STATUS
STATUS
ANALOG B
ANALOG B
VALVE
VALVE
T T T T T
ENCODER 1
ENCODER 1
ENCODER 1
ENCODER 1
POWER
POWER
POWER
POWER
POWER
ANALOG A
ANALOG A
ANALOG A
ANALOG A
ANALOG A
ENCODER 2
ENCODER 2
ENCODER 2
DM-101
DM-103VA
DM-102
DM-104
DM-102VA
HSB
HSB
HSB
HSB
HSB
ENCODER 3
Delem
Delem
Delem
Delem
Delem
Note Redrawn Date
Luchthavenweg 42, 5657 EB
DM-101 DM-102 DM-102VA DM-103VA DM-104 Description Eindhoven, the NETHERLANDS
50.00
Clearance
Side clearance
24V 24V 24V 24V 24V 24V
1 9 17 1 9 17
2 10 18 2 10 18
OUT
OUT
OUT
OUT
3 11 19 3 11 19
4 12 20 4 12 20
5 13 21 5 13 21
IN / OUT
IN / OUT
6 14 22 6 14 22
IN
IN
IN
IN
7 15 23 7 15 23
8 16 24 8 16 24
0V 0V 0V 0V 0V 0V
STATUS
STATUS
ANALOG B
ANALOG B
VALVE
VALVE
T T
240.00
213.50
227.00
ENCODER 1
ENCODER 1
POWER
POWER
Delem DM-10X
ANALOG A
ANALOG A
DM-103VA
DM-103VA
Void
ID-number: NNNNNNN
Voltage: 24VDC
IF BROKEN
WARRANTY
SEE INSTRUCTION MANUAL
Made in the Netherlands BEFORE OPERATING
8575-001
8575-002
8562-005
8562-006
8576-001
8577-001
HSB
HSB
ENCODER 3
ENCODER 3
Delem
Delem
1.0
13.25
132.30 5.50
15.00
50.00
136.90 11.65 30.00
Cable clearance
150.30
Note Redrawn Date
155.00 Luchthavenweg 42, 5657 EB
Description
Delem Eindhoven, the NETHERLANDS
175.00
185.00 Note Redrawn Date Dimensions DM-10X
A HNF 14-02-2007
Description
Format Number Issue
MOD#555: 8577-001 DM-104 added
A3 8576-601 A
Measures in mm,unless Drawn Date
otherwise specified HNF 16-11-2004 No unauthorized copying allowed Scale
DC-SET-10X DC-161586 DC-SET-10X-S DC-177988 DC-SET-10X-SL DC-178909
Clamping-yoke Spring connection Spring connection DC-SUBD-15-F-CP
connection + Led indication
(screw)
OUT
OUT
3 11 19
4 12 20 ANALOG A
5 13 21
IN / OUT
6 14 22 D5060-005
IN
IN
7 15 23 15p.SubD Female
8 16 24
0V 0V 0V
DC-SUBD-15-M-CP
IN / OUT
STATUS
3 x DC-161586 3 x DC-177988 3 x DC-177909
Clamping-yoke connection Spring connection Spring connection + Led ANALOG B
1 x Power LED
8 x I/O LED
ANALOG B
15p.SubD Male D5060-004
VALVE
Full version:
DK-1079-002 1.5 m VALVE DC-SUBD-9-M-CP
1079-002/- T
or ENCODER1
ENCODER 1
Pressure control version only:
POWER
DK-1079-006 1.5 m
DC-SUBD-9-M-CP D5060-001
POWER 24VDC 9p.SubD Male
ENCODER2
ANALOG A
DK-1080-002 1.5 m
ENCODER 2
1080-002/-
1 2
DM-103VA
HSB DC-SUBD-9-M-CP
DA-66W & DA-69W : 9p.SubD Male D5060-001
D-5115-001
HSB
DC-1064-001 HSB Terminator HSB ENCODER3
ENCODER 3
Delem
ASSY
HSB CONVERTER DK-HSB-RJ45-05
0.50 m 9p.SubD Male D5060-001
LVDT 1 1 1 1 LVDT
HSB GND 24V 0V Y1 Y2
2 2 2 2
45 78 2 3 2 3
RJ45 Use
Delem
RJ45-HSB
Cable
OPENING
PRESSING
MANUAL
PARALLEL
R-IN (R-axis positive input)
T (Tandem)
C (step Change)
FAST CLOSING
PUMP
24V 0V
24V
I/O
Link to
other 24V 0V
modules
or
Delem DK-HSB-RJ45-NNN
Shunt
24V 0V 24V 0V 24V 0V
Delem
HSB 0V
1064-001 9P.SUBD 9P.SUBD I/O
Delem DK-1080-002
Male Male
Max. 100 mA
Max. 100 mA
RJ45 RJ45
45 78 45 78 1 2 1 t/m 9 3 4 5 9 2 10 3 11 1 15 16 8 7 12 5 13 6 14 4 11 12 13 1 t/m 9
HL HL 24V 0V 24V LVDTY1 0V 24V LVDTY2 0V 5 6 7 8 0V 0V 9 10 11 12 13 14 15 16 21 22 23 24 0V
24V A- A+ B- B+ 0V P 24V P+ P- P 0V 24V A- A+ B- B+ 0V
HSB HSB POWER ENCODER 1 ANALOG B ANALOG B ENCODER 2 COM COM COM
VALVE Y1 VALVE VALVE Y2
ANALOG A
15P.SUBD 24V
0V
10V
Female I/O
0-10V
0V
I/O
A<
A>
10K
ER
Crowning
LDP
UDP
MUTE
CLAMP
Potentiometer
2nd MUTE
CNC START
Function output F1
Function output F2
Function output F5
CNC READY
(End of Relaxtion)
IN OUT
HSB ANALOG A POWER VALVE STATUS
8
7
6
5
4
3
2
1
24V
0V
11
16
15
14
13
12
10
0V
24V
2 Y1 A- Delem DM-102VA
2 OUTAN1 0V 2 0V 2 Y1 +12V IN OUT
3 Y1 B- ENCODER 2 ENCODER 1 ANALOG B
24
23
22
21
20
19
18
17
24V
0V
8
3 REF1 10V 1 T0 (REF) T0 T0 T0 3 Y1 24V Max.100mA
4 Y2 0V
4 IN1A 2 T2 (B) T2 T2 T2 4 Y1 LVDT
7
5 Y2 A-
5 IN1A 0V 3 T1 (A) T1 T1 T1 5 Y1 0V
6 Y2 B-
6
6 IN1B 4 + 12V + 12V / / 6 Y1 +/-10V
2
1
7 P 0V See drawing 8576-601 for module dimensions & mounting instructions
7 IN1B 0V 5 GND GND GND GND 7 P 0V
5
8 P- Note Redrawn Date
8 N.C. 6 T0 (REF) / T0 8 P 0-10V Luchthavenweg 42, 5657 EB
9 Y1 24V
6 7 8 9
4
9 OUTAN2 -10V...+10V 7 T2 (B) / T2 9 Y2 -12V Description Eindhoven, the NETHERLANDS
10 Y1 A+
1 2 3 4 5
10 OUTAN2 0V 8 10 Y2 +12V
11 12 13 14 15 16
T1 (A) / T1
3
11 Y1 B+ Example connections: P, Y1, Y2,
9 10 11 12 13 14 15
9 10 11 12 13 14 15
11 REF2 10V 12 Y2 24V 9 + 5V + 5V + 5V 11 Y2 24V Max.100mA Note Redrawn Date
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
2
12 IN2A 13 Y2 A+ 12 Y2 LVDT
IN2A 0V 13 Y2 0V Description Crowning.
9 10
13
1
14 Y2 B+ In case of 12VSE Format Number Issue
14 IN2B 15 P 24V 14 Y2 +/-10V
bridge pins 6,7,8 and 9 A3 Page 1 /1 8562-101 -
15 IN2B 0V 16 P+ 15 N.C. Measures in mm,unless Drawn Date
otherwise specified HNF 11-07-2005 No unauthorized copying allowed Scale
Note 1 : Leave unconnected pins open.
Note 2 : 24V relais supply must be separated from 24V supply
Note 3 : Do not place a diode across valves.
Linear Valve Y1 System Valve Y2 Linear
Scale Y1 Pressure Scale Y2
DAonWindows
CNC
1 4 A B A B 1 4
LVDT 1 1 1 1 LVDT
HSB GND 24V 0V Y1 Y2
2 2 2 2
45 78 2 3 2 3
RJ45 Use
Delem
RJ45-HSB * Axis 3
(R-axis)
Cable
OPENING
PRESSING
MANUAL
PARALLEL
R-IN (positive input)
RSD
T (Tandem)
C (step Change)
FAST CLOSING
PUMP
24V 0V
24V
I/O
Link to
other 24V 0V
modules
or
Delem DK-HSB-RJ45-NNN
Shunt
24V 0V 24V 0V 24V 0V
Delem
HSB 0V
1064-001
I/O
Delem DK-1080-002
Max. 100 mA
Max. 100 mA
RJ45 RJ45
45 78 45 78 1 2 1 t/m 9 3 4 5 9 2 10 3 11 1 15 16 8 7 12 5 13 6 14 4 11 12 13 1 t/m 9
HL HL 24V 0V 24V LVDTY1 0V 24V LVDTY2 0V 5 6 7 8 0V 0V 9 10 11 12 13 14 15 16 21 22 23 24 0V
24V A- A+ B- B+ 0V P 24V P+ P- P 0V 24V A- A+ B- B+ 0V
HSB HSB POWER ENCODER 1 ANALOG B ANALOG B ENCODER 2 COM COM COM
VALVE Y1 VALVE VALVE Y2
LVDTY1 LVDTY2
System galvanic insulation galvanic insulation galvanic insulation
Valve Y1 Pressure Valve Y2
INPUTS INPUTS
DM-103VA 8576-001 PIN 9..16 programmable:
Servo OUTPUTS 1...4 max.1.5A INPUT or OUTPUT OUTPUTS
Axis 3 Crowning galvanic insulation galvanic insulation galvanic insulation
ANALOG A
0V
0V
10V
Female Male I/O
0-10V
+/-10V
0V
I/O
OK
A<
A>
+/-10V 0V
ER
LDP
UDP
Amplifier
Rmin=1K
Rmax=10K
MUTE
IN POSITION
CLAMP
Axis 3 Potentiometer
2nd MUTE
CNC START
Function output F1
Function output F2
*Axis 3
CNC READY
Crowning
Feedback
(End of Relaxtion)
M E
(Upper Dead Point)
(Lower Dead Point)
Encoder
Axis 3 Axis 3 *See connection diagram: 9087-102 for details " OK & START"
IN OUT
HSB ANALOG A POWER VALVE STATUS
8
7
6
5
4
3
2
1
24V
0V
11
16
15
14
13
12
10
0V
24V
0V
8
3 REF1 10V 1 T0 (REF) T0 T0 T0 3 Y1 24V Max.100mA
4 Y2 0V
4 IN1A 2 T2 (B) T2 T2 T2 4 Y1 LVDT
7
5 Y2 A-
5 IN1A 0V 3 T1 (A) T1 T1 T1 5 Y1 0V
6 Y2 B-
6
6 IN1B 4 + 12V + 12V / / 6 Y1 +/-10V
2
1
7 P 0V See drawing 8576-601 for module dimensions & mounting instructions. See DM-100 installation manual for electrical characteristics.
7 IN1B 0V 5 GND GND GND GND 7 P 0V
5
8 P- (Rev.) Redrawn Date
8 N.C. 6 T0 (REF) / T0 8 P 0-10V Luchthavenweg 42, 5657 EB
9 Y1 24V
6 7 8 9
4
9 OUTAN2 -10V...+10V 7 T2 (B) / T2 9 Y2 -12V Description Eindhoven, the NETHERLANDS
10 Y1 A+
1 2 3 4 5
10 OUTAN2 0V 8 10 Y2 +12V
11 12 13 14 15 16
T1 (A) / T1
3
11 Y1 B+
9 10 11 12 13 14 15
9 10 11 12 13 14 15
11 REF2 10V 9 + 5V + 5V + 5V
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Servo 3,
2
12 IN2A 12 Y2 LVDT A HNF 01-03-2007
13 Y2 A+
IN2A 0V 13 Y2 0V Description Crowning.
9 10
13
1
14 Y2 B+ In case of 12VSE Format Number Rev.
14 IN2B 14 Y2 +/-10V
15 P 24V bridge pins 6,7,8 and 9 Ref.9087-102 details "OK & START" added
15 IN2B 0V 16 P+
15 N.C. Measures in mm,unless Drawn Date
A3 Page 1 /1 8576-101 A
otherwise specified HNF 16-12-2005 No unauthorized copying allowed Scale
Note 1 : Leave unconnected pins open.
Note 2 : 24V relais supply must be separated from 24V supply
Delem
DAonWindows
CNC
START
RSD
24V 0V
24V
I/O
Link to
other 24V 0V
modules
or
Delem DK-HSB-RJ45-NNN
Shunt
Delem
HSB 0V
1064-001
I/O
Delem DK-1080-002
RJ45 RJ45
45 78 45 78 1 2
HL HL 24V 0V 5 6 7 8 0V
HSB HSB POWER COM
galvanic insulation
INPUTS
Delem DM-101 8575-001
OUTPUTS 1...4 max.1.5A
Servo galvanic insulation
Axis 1
ANALOG A
OUTAN1 OUTAN1 N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C. ENCODER 1 COM
-10V..+10V 0V 24V 1 2 3 4
1 2 8 9 10 11 12 13 14 15 1 t/m 9
0V
Female Male I/O
+/-10V
0V
I/O
OK
+/-10V 0V
Amplifier
IN POSITION
Axis 1
* Axis 1
Feedback
M E
Encoder
Axis 1 Axis 1 *See connection diagram: 9087-102 for details " OK & START"
IN OUT
HSB ANALOG A POWER STATUS
8
7
6
5
4
3
2
1
24V
0V
Delem DM-101
2 OUTAN1 0V 2 0V
ENCODER 1
3 REF1 10V 1 T0 (REF) T0 T0 T0
4 IN1A 2 T2 (B) T2 T2 T2
5 IN1A 0V 3 T1 (A) T1 T1 T1
6 IN1B 4 + 12V + 12V / /
2
1
See drawing 8576-601 for module dimensions & mounting instructions.
7 IN1B 0V 5 GND GND GND GND (Issue) Redrawn Date
8 N.C. 6 T0 (REF) / T0 Luchthavenweg 42, 5657 EB
6 7 8 9
10 OUTAN2 0V 8 T1 (A) / T1
Example connections:
9 10 11 12 13 14 15
11 REF2 10V 9 + 5V + 5V + 5V (Issue) Redrawn Date
1 2 3 4 5 6 7 8
12 IN2A A HNF 01-03-2007 Servo 1,
13 IN2A 0V Description
In case of 12VSE Format Number Issue
14 IN2B Ref.9087-102 details "OK & START" added
bridge pins 6,7,8 and 9 A3 Page 1 /1 8575-101 A
15 IN2B 0V Measures in mm,unless Drawn Date
otherwise specified HNF 16-12-2005 No unauthorized copying allowed Scale
Note 1 : Leave unconnected pins open.
Note 2 : 24V relais supply must be separated from 24V supply
Delem
DAonWindows
CNC
START
RSD
START
RSD
24V 0V
24V
I/O
Link to
other 24V 0V
modules
or
Delem DK-HSB-RJ45-NNN
Shunt
Delem
HSB 0V
1064-001
I/O
Delem DK-1080-002
RJ45 RJ45
45 78 45 78 1 2
HL HL 24V 0V 5 6 7 8 0V 0V 9 10 11 12 13 14 15 16 21 22 23 24 0V
HSB HSB POWER COM COM COM
0V
0V
Female Male Male I/O
+/-10V
+/-10V
0V
I/O
OK
OK
+/-10V 0V +/-10V 0V
Amplifier Amplifier
IN POSITION
IN POSITION
Axis 1 Axis 2
Function output F1
Function output F2
Function output F3
Function output F4
Function output F5
* Axis 1 *Axis 2
Feedback Feedback
M M E E
Encoder Encoder
Axis 1 Axis 2 Axis 1 Axis 2 *See connection diagram: 9087-102 for details " OK & START"
IN OUT
HSB ANALOG A POWER STATUS
8
7
6
5
4
3
2
1
24V
0V
11
16
15
14
13
12
10
0V
24V
Delem DM-102
2 OUTAN1 0V 2 0V IN OUT
ENCODER 2 ENCODER 1
24
23
22
21
20
19
18
17
24V
0V
2
1
See drawing 8576-601 for module dimensions & mounting instructions.
7 IN1B 0V 5 GND GND GND GND (Issue) Redrawn Date
8 N.C. 6 T0 (REF) / T0 Luchthavenweg 42, 5657 EB
6 7 8 9
10 OUTAN2 0V 8 T1 (A) / T1
Example connections:
9 10 11 12 13 14 15
11 REF2 10V 9 + 5V + 5V + 5V (Issue) Redrawn Date
1 2 3 4 5 6 7 8
12 IN2A A HNF 01-03-2007 Servo 1, Servo 2,
13 IN2A 0V Description
In case of 12VSE Format Number Issue
14 IN2B Ref.9087-102 details "OK & START" added
bridge pins 6,7,8 and 9 A3 Page 1 /1 8562-109 A
15 IN2B 0V Measures in mm,unless Drawn Date
otherwise specified HNF 16-12-2005 No unauthorized copying allowed Scale
Note 1 : Leave unconnected pins open.
Note 2 : 24V relais supply must be separated from 24V supply
Delem
DAonWindows
CNC
24V 0V
24V
I/O
Link to
other 24V 0V
modules
or
Delem DK-HSB-RJ45-NNN
Shunt
Delem
HSB 0V
1064-001
I/O
Delem DK-1080-002
RJ45 RJ45
45 78 45 78 1 2
HL HL 24V 0V 5 6 7 8 0V 0V 9 10 11 12 13 14 15 16 21 22 23 24 0V
HSB HSB POWER COM COM COM
ANALOG A
COM COM COM
24V 1 2 3 4 24V 9 10 11 12 13 14 15 16 24V 17 18 19 20
24V
I/O
0V
I/O
IN OUT
HSB ANALOG A POWER STATUS
8
7
6
5
4
3
2
1
24V
0V
ANALOG A POWER
15 POLE MALE 2 POLE MALE
IN / OUT
9
11
16
15
14
13
12
10
0V
24V
Delem DM-104
2 OUTAN1 0V 2 0V IN OUT
24
23
22
21
20
19
18
17
24V
0V
3 REF1 10V
4 IN1A
5 IN1A 0V
6 IN1B
2
1
See drawing 8576-601 for module dimensions & mounting instructions
7 IN1B 0V
Note Redrawn Date
8 N.C. Luchthavenweg 42, 5657 EB
9 OUTAN2 -10V...+10V Description Eindhoven, the NETHERLANDS
10 OUTAN2 0V
Example connections:
9 10 11 12 13 14 15
11 REF2 10V Note Redrawn Date
1 2 3 4 5 6 7 8
12 IN2A IN / OUT 1-24
13 IN2A 0V Description
Format Number Issue
14 IN2B
15 IN2B 0V Measures in mm,unless Drawn Date
A3 Page 1 /1 8577-101 -
otherwise specified HNF 16-12-2005 No unauthorized copying allowed Scale