Professional Documents
Culture Documents
APC700PAN User’s
Manual
Table of revisions:
Table of references:
The technical data and specifications are valid at the time of printing.
We reserve the right to subsequent alterations.
2
3AFE58177580 APC700PAN User’s Manual
Contents Page
1. General information .......................................................................................... 5
1.1. Description ............................................................................................. 5
2. APC 700 PAN ................................................................................................... 6
2.1. Overview ................................................................................................ 6
2.2. Mechanical Description .......................................................................... 6
2.3. Technical specification........................................................................... 7
2.4. Connectors............................................................................................. 8
2.5. Cabling................................................................................................... 9
2.6. Communication ...................................................................................... 9
2.7. Operating modes ................................................................................... 10
2.7.1 Going to the internal mode ....................................................... 10
2.7.2 Automatic leaving from the internal mode .................................. 10
2.7.3 Selection of the researching alarms ........................................... 11
3. APC 700 PAN Test Instructions ( Version 2.00 )............................................... 12
3.1. Bush button order: ................................................................................. 12
3.2. Cold start (power on for the first time). ................................................... 12
3.3. Internal Test: .......................................................................................... 13
3.4. Normal operation ................................................................................... 13
4. Using the ACV 700 PANEL ............................................................................... 14
4.1. Push buttons .......................................................................................... 14
4.2. Signal display......................................................................................... 15
5. Using the DCV 700 PANEL............................................................................... 18
5.1. Push buttons .......................................................................................... 18
5.2. Signal display......................................................................................... 19
6. Using the Parameter Panel ............................................................................... 21
6.1. Function Description .............................................................................. 22
6.1.1. Upload &Save in APC............................................................... 22
6.1.2. Download to DDC ..................................................................... 22
6.1.3. Save in drive ............................................................................. 23
6.1.4. Save value ................................................................................ 23
6.1.5. Display messages:.................................................................... 25
3
APC700PAN User’s Manual 3AFE58177580
4
3AFE58177580 APC700PAN User’s Manual
1. General information
1.1. Description
This unit gives technical information about the APC 700 PAN Control
Panel, and APC 700 PAN Control Panel test instructions.
5
APC700PAN User’s Manual 3AFE58177580
2.1. Overview
The APC 700 PAN control panel is used as a basic interface for the
user to see:
status information (ready, run, fault, communication)
fault logger display with 100 events memory
reference values (speed, frequency, torque)
actual values (speed, frequency, torque)
It can be used to control from 1 to 4 DDCs one by one, depending on
the application program. Panel functions are freely programmable.
The APC 700 PAN can be mounted into the cabinet door, into the
control desk or on the wall (by using the assembling box).
DR 1 SPEED
DRIV E rpm 1000 #2
SPECurrent
ED A 1500RP
100 M
F1 F 2
Request Group Function
F3 F 4
*/ R Fast Parameter Enter
6
3AFE58177580 APC700PAN User’s Manual
Dimensions:
Pushbuttons:
7
APC700PAN User’s Manual 3AFE58177580
2.4. Connectors
The connection is done to the APC 700 PPW power supply board,
connector X1 as follows:
X1:1 24 VDC
X1:2 0V GND
X1:3 RS signal A
X1:4 RS signal B
X1:5 floating frame
X1:6 fixed frame
X3:1 RS signal A
X3:2 9 VDC
X3:3 9 VDC
X3:4 0 V GND
X3:5 0 V GND
X3:6 RS signal B
X2 is connected to the frame, by the jumper S1, the GND can be
connected to the frame.
X2
X1 X3
S1 5
6
1 2 3 4 5 6 3
2
4
8
3AFE58177580 APC700PAN User’s Manual
2.5. Cabling
APC
(YPP 110A)
APC 700 PAN APC 700 PPW X2:1
S1 X2:6
Floating X1:5
Frame X2:7
Frame
X1:6
X2:8
Frame
X2
S1
Floating X1:5
Frame
Frame
X1:6
X2
2.6. Communication
9
APC700PAN User’s Manual 3AFE58177580
Panel will go automatically from the internal mode to the normal mode if
no buttons will be pressed during 2 minutes. If any of buttons will be
pressed then the new delay counting will be started.
10
3AFE58177580 APC700PAN User’s Manual
(The negative logger number has been set in the PANCON function
block. With it will be selected the investigation of all alarms. This will
compensate settings of the panel.)
If the negative logger number has been set in the PANCON function
block, it wins setting of the panel and the investigation of all events is
select.
If the display of all alarms has been selected with the PANCON function
block, ↑ up-, ↓ down and */R buttons has no function and on the display
is permanent text * ALL EVENTS.
11
APC700PAN User’s Manual 3AFE58177580
S1 S2 S3 S4 S5
S6 S7 S8 S9 S10
ô Remove power.
(Internal state)
í Connect power again.
Panel will display the text: "New Eprom / Wait..."
After a short delay panel goes to internal mode and displays:
"Time out select: *10"
S1 button will select the display: "ID number: *1";
User can change the number value on the display with buttons
S2
(increase) and S7 (decrease).
New value must be stored to EEprom with button S6 (reset)
even
if the values are not changed.
The "*" sign will indicate that the new value is stored
successfully.
12
3AFE58177580 APC700PAN User’s Manual
13
APC700PAN User’s Manual 3AFE58177580
14
3AFE58177580 APC700PAN User’s Manual
− vector control:
R 1 S P E E D ( r p m ) 0
C U R R E N T ( A ) 0
− scalar control:
R 1 F R E Q . ( H z ) 0 . 0
C U R R E N T ( A ) 0
R 1 S P E E D ( r p m ) 0
R E F E R E N C E 0
R 1 T O R Q U E ( % ) 0
R E F E R E N C E 0
R 1 F R E Q . ( H z ) 0 . 0
R E F E R E N C E 0 . 0
R 1 S T A T U S
C O M M . E R R O R
F A U L T
C
R E A D Y F O R R U N
R U N N I N G
15
APC700PAN User’s Manual 3AFE58177580
R 1 R U N T I M E
I N H O U R S 0
R 1 F R E Q . ( H z ) 0 . 0
R E F E R E N C E 0 . 0
R 1 S T A T U S
C O M M . E R R O R
F A U L T
R E A D Y F O R R U N
R U N N I N G
R 1 R U N T I M E
I N H O U R S 0
16
3AFE58177580 APC700PAN User’s Manual
The drives have two control modes, remote control and local control.
Control mode can be changed by pressing together */R and F4 push
buttons.
In remote control the basic ident of the drive (drives) is DR1 (DR1 to
DR4), but it can be named freely (max. 3 character). In local control the
ident of the drive (drives) is L1 (L1 to L4).
In remote control the display of the panel can be scrolled, but control is
not available.
When the local control is selected it is possible to scroll the display,
start and stop the drive, change the speed reference (vector control) or
frequency reference (scalar control) and give the external
acknowledge.
Speed reference and frequency reference changes can be made only
on the display in question.
Changing the reference value:
17
APC700PAN User’s Manual 3AFE58177580
18
3AFE58177580 APC700PAN User’s Manual
R 1 S P . A C T . ( r p m ) 0
C U R R . A C T ( A ) 0
R 1 S P . R E F . ( % ) 0
S P . A C T . ( % ) 0
R 1 F I . A C T . ( A ) 0
A R M . A C T . ( V ) 0
R 1 T O R Q . R E F ( %) 0 . 0
T O R Q . A C T ( %) 0 . 0
R 1 S T A T U S
C O M M . E R R O R
F A U L T
E L E C T . D I S C O N .
M A I N C O N T . O P E N
R E A D Y F O R R U N
R U N N I N G
D D C T O O L I N L O C A L
R 1 R U N T I M E
I N H O U R S 0
19
APC700PAN User’s Manual 3AFE58177580
The drives have two control modes, remote control and local control.
Control mode can be changed by pressing together */R and F4 push
buttons.
In remote control the basic ident of the drive (drives) is R1 (R1 to R4).
In local control the ident of the drive (drives) is L1 (L1 to L4).
In remote control the display of the panel can be scrolled, but control is
not available.
When the local control is selected it is possible to scroll the display,
start and stop the drive, change the speed reference and give the
external acknowledge.
Speed reference changes can be made only on the display in question.
20
3AFE58177580 APC700PAN User’s Manual
The drive types, numbers and the parameter indexes must be defined
in the APC software.
If there is just one panel connected to the APC, the PAR mode is
entered by changing the ID number in the internal mode of the ACV
700 PAN. The ID number of the parameter panel program is a pre-
programmed value in the APC application program (this is normally 10
to 15, since these node numbers do not have a link supervision).
DR 1 SPEED
DRIV E rpm 1000 #2
SPECurrent
ED A 1500RP
100 M
F1 F 2
Request Group Function
F3 F 4
*/ R Fast Parameter Enter
21
APC700PAN User’s Manual 3AFE58177580
DRIVE NUMBER 1
Upload&Save in APC
F &
E FUNCTION & ENTER uploads the
parameters from the selected drive and
saves them on the flash PROM of the APC.
DRIVE NUMBER: 1
Download to DDC
F &
E FUNCTION & ENTER downloads the
parameters to the selected drive.
22
3AFE58177580 APC700PAN User’s Manual
DRIVE NUMBER: 1
Save in DDC
F &
E FUNCTION & ENTER stores the parameters
on the EEPROM of the selected drive.
G &
= Displays the type and identity number
of the drive.
P &
= Displays the index of the parameter in
the drive.
23
APC700PAN User’s Manual 3AFE58177580
++/--
&
= FAST & EQUAL Sets the old
parameter value to the counter output.
F &
E FUNCTION & ENTER Reads the counter
output to parameter and saves the
parameter value on the flash PROM of the
APC.
24
3AFE58177580 APC700PAN User’s Manual
DRIVE NUMBER: 1
Upload&Save in APC
F&E
DRIVE NUMBER: 1
uploading...
DRIVE NUMBER: 1
Saving in APC...
DRIVE NUMBER: 1
...done
R DRIVE NUMBER: 1
timeout ERROR! (R)
R DRIVE NUMBER: 1
ERROR! (R)
Panel displays of the upload & store function.
25
APC700PAN User’s Manual 3AFE58177580
DRIVE NUMBER: 1
Download to DDC
F&E
DRIVE NUMBER: 1
Downloading...
DRIVE NUMBER: 1
...done
R DRIVE NUMBER: 1
timeout ERROR! (R)
R DRIVE NUMBER: 1
ERROR! (R)
Panel displays of the download functions.
26
3AFE58177580 APC700PAN User’s Manual
DRIVE NUMBER: 1
Save in DDC
F&E
DRIVE NUMBER: 1
Saving in DDC...
DRIVE NUMBER: 1
...done
R DRIVE NUMBER: 1
timeout ERROR! (R)
R DRIVE NUMBER: 1
ERROR! (R)
Display of the store in drive function.
27
APC700PAN User’s Manual 3AFE58177580
F&E
28