Professional Documents
Culture Documents
LIU 2019-7-1
□ Approved
□ Reject
Customer Comment:
Approval
0 APPROVAL 1
1 REVISION HISTORY 2
2 CONTENT 3
3 FEATURES 4
4 GENERAL SPECIFICATIONS 4
5 OUTLINE DIMENSIONS 5
6 PIN CONNECTIONS 6
7 BLOCK DIAGRAM 7
8 APPLICATION CIRCUIT EXAMPLE 8
9 ABSOLUTE MAXIMUN RATING 9
10 ELECTRICAL CHARACTERISTICS 9
11 ELECTRO-OPTICAL CHARACTERISTICS 10
12 TIMING CHARACTERISTICS 12
13 DISPLAY COMMANDS 17
14 CHARACTER PATTERN 19
15 QUALITY LEVEL 20
16 PRECAUTIONS 22
17 PACKAGE INFORMATION 23
4.GENERAL SPECIFICATIONS
ITEM DESCRIPTION UNIT
Outline Size 69.0(L)×31.9(W)×5.0(T) mm
STN, Gray, Transflictive,
LCD Type ---
Positive,1/17Duty,1/4Bias
Display type 14 Character×2 Lines ---
View Area 57.0×22.0 mm
Display Area 55.04×18.25 mm
Dots size 0.56×0.66 mm
Dots pitch 0.62×0.72 mm
Controller & driver ST7038SI ---
View Direction 12 O’Clock ---
Interface mode I2C ---
VDD&VOP(Type) 3.0 V & 5.0 V V
Backlight(Type) White, 3.0V,15mA ---
Operation Temp. 0~+50 ℃
Storage Temp. -10~+60 ℃
Module weight 12.5±10% g
TEL:+86-755-27664234
5.OUTLINE DIMENSIONS
http://www.huaxinjin.com
深圳市华显晶显示技术有限公司
NAME: DATE: MODEL NUMBER :
Page:
SHEET: 1 OF 1
DESIGN BY: Liu Gong 2019-5-28
HSG1402-01
CHECKED BY:
NAME: LCM
APPROVED BY: DEFAULT UNITS: mm PROJECTION
5/23
Shenzhen Huaxianjing Technology Co.,LTD
深圳市华显晶显示技术有限公司
__________________________________________________________________________________________________________
深圳市华显晶显示技术有限公司
Shenzhen Huaxianjing Technology Co.,LTD
__________________________________________________________________________________________________________
6.PIN CONNECTIONS
Pin No. Pin Out Description
Hardware reset input pin. When RSTB is “L”, internal initialization procedure is
1 RST executed and the internal registers will be set as default value.
2 SCL Serial clock input.
3 SDA Serial data input.
4 VSS Ground.
5 VDD Power for logic voltage circuit.
6 VG VG is the LCD driving voltage for segment circuits.
7 V0 V0 is the LCD driving voltage for common circuits at negative frame.
8 XV0 XV0 is the LCD driving voltage for common circuits at positive frame.
LCD Ta=0℃ -- -- --
driveVoltage(
V0–XV0 Ta=25℃ 4.7 5.0 5.3 Volt
recommended
Voltage) Ta=50℃ -- -- --
VDD =3.0V
Power Supply IDD - 180 300 uA
Ta=25℃
Current for
LCM ILED VLED= 3.0 V -- 15 20 mA 1
℃;Humidity:50±10%RH
The external visual inspection
The inspection shall be performed by using a single 20W fluorescent lamp for illumination
and the distance from LCD to eyes of the inspector should be 30cm or more.
Classification of defects
A major defect
A major defect refers to A defect which may substantially degrade usability for product applications.
Minor defect
A Minor defect refers to A defect which is not considered to substantially degrade product application or A
defect which deviates from existing standards almost unrelated to the effective use of the product or its
operation
Sampling procedures for each items acceptance level table
Defect type Sampling procedures AQL
MIL-STD-105D Inspection level1
Major defect 1.0
normal inspection Single sample inspection
MIL-STD-105D Inspection level1
Minor defect 2.5
normal inspection Single sample inspection
Life time
50,000Hrs (25℃ 45%RH in the room without ray of sun)
Items of reliability
ITEM CONDITIONS CRITERION
High temperature operation test +50℃ \240 hours 1. It judged at room
temperature after 2 hours to be
good as appearance and
electrical test is normal after
the experiment.
2. Current consumption should
within the specification of Approval
sheet Electro-optical characteristics
Low temperature operation test 0℃ \ 240 hours 5-10pcs
High temperature/humidity storage +40℃,90%RH \240 hours
test
High temperature storage test +60℃ \ 240 hours
Low temperature storage test -10℃ \ 240 hours
CYCLES: 10
Vibration Random Wave: 10 ~ 50 Hz
Each Direction (x, y, z ): 30
Min.
Operation
1. It is essential to drive the LCD within the specified voltage limits, since a higher driving voltage than allowed causes a shorter
LCD lifetime. Under these circumstances, electrochemical reactions will result in undesirable deterioration of the LCD.
2. The response time of the LC fluid is considerably longer at low temperature than in the normal operating temperature range.
On the other hand, the LCD will show a dark blue color at high temperatures. Those phenomena do not indicate a malfunction
or defect of the LCD. Back at normal temperatures, the LCD will return to its original behavior.
3. If the display area is pressed hard during operation, some abnormal display patterns might appear. However, the display will
resume normal operation after turning the module off and on.
4. Moisture on the terminals could cause an electrochemical reaction resulting in an open terminal connection. If the
environmental temperature is higher than 50℃, it is required that the relative humidity is 50% or less.
Long-time storage
For long-term storage the following methods are highly recommended:
1. Store the product in a polyethylene bag with a sealed opening to prevent fresh air entering from the outside. Placing it with a
desiccant is not necessary.
2. Store the product in a dark place, with the temperature in the range from 0℃ to 50℃.
3. Keep the sensitive polarizer surface of the LCD panels clear of any contact. We recommend using the container that was used
by HXJ to deliver the products.
Cleaning of product
To clean the product make sure to use absorbent cotton cloth or other soft material like chamois. Make sure to rub it gently and
do not use chemicals when cleaning.
Packaging Material
No. Item Model Dimensions (mm) Quantity
1 LCM - - --
2 POF - - --
3 TRAY - - --
4 SMALL BOX - 385.0×315.0×200.0 2
5 BIG BOX - 398.0×331.0×430.0 1
Tray
=>
Small Box Big Box
Tray stacking
=>