Professional Documents
Culture Documents
872196
Copyright © 2011
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmit-
ted, in any form or by any means, electronic, mechanical, photocopying or otherwise, without the prior writ-
ten permission of Bell Equipment Company SA (Pty) Limited as the copyright holder.
This manual has been produced to assist you in ordering of parts for the maintenance of your BELL
EQUIPMENT machine.
The information contained in the manual is in a logical sequence. Each illustrated breakdown is supported
with a parts list.
The parts manual has been produced by the Technical Documentation Department of BELL EQUIPMENT
Co. Every effort has been made to ensure that the information in this manual was correct at the time of
publication. BELL EQUIPMENT Co. has a policy of continuous product development, improvement and
design. BELL EQUIPMENT Co. reserves the right to change, amend and update the design of its product
at any time without prior notice. With this policy, changes may have occurred that are not included in this
manual.
Whilst every endeavour has been made to provide accurate and reliable information, BELL EQUIPMENT
Co. specifically disclaims any actual or implied warranty and under no circumstances shall be liable for any
loss, damage or injury to person or property suffered, whether direct, or indirect or consequential, arising
from the use of this manual. In particular and without detracting from the above, the disclaimer also applies
in the event of any specification, warning, or representation contained in this manual being inadequate,
inaccurate, or unintentionally misleading.
The user is urged to strictly comply with the instructions and warnings that are given in the interests of gen-
eral safety. Please do not hesitate to contact your BELL EQUIPMENT Product Support Representative
whenever you have a query on your BELL product or this manual. The address of your nearest BELL
EQUIPMENT branch or dealer is as follows:-
LOCATION OF OPERATIONS
RICHARDS BAY - HEAD OFFICE:
Bell Equipment Group
Physical Address: Carbonode Cell, Alton,Richards Bay,3900
Tel: +27 (0)35 907 9111
Fax: +27 (0)35 797 4336
E-mail: sales@bellequipment.com
ASIA PACIFIC:
AUSTRALIA
Bell Equipment Australia (Pty) Limited
Physical Address: 4 Karratha Street, P.O. Box 34, Welshpool, WA 6986, Australia
Contact: Owen Kees (Marketing Manager)
Mobile: +61-(0)418 900 323
Tel : +61-8-9356 1033
Fax :+61-8-9356 1233
E-mail: owenk@bell.co.za
SINGAPORE
Bell Equipment (SEA) PTE Ltd
Physical Address: 10 Anson Road, #22-02A International Plaza, Singapore, 079903
Contact: Mohd Johari Ahmead (Dealer Development Sales Manager)
Mobile: +65 966 36404
Tel : +65 622 08 004 or +65 622 62 362
Fax :+65 622 03 004
E-mail: bellequipment@singnet.com.sg (Johari) or wendycmw@singnet.com.sg
EUROPE :
FRANCE
Bell France SARL
Physical Address: Route d’ Argenton-Sur-Creuse, 23800 Dun Le Palestel, France
Contact: Claude Boulet (Director) Vincent Valadas (Technical Director)
Mobile: +33 60719 5407
Tel : +33 55589 2356
Fax :+33 55589 2324
E-mail: claudeb@fr.bellequipment.com
GERMANY
Bell Equipment (Alsfeld) GmbH
Physical Address: Willi-Brandt Strasse 4-6, D-36304, Alsfeld, Germany
Contact: Andre Krings (Managing Director)
Mobile: +49 176 220 024 416
Tel: +49 6631 911 300
Fax: +49 6631 911 313
E-mail: andrek@de.bellequipment.com
SPAIN
Bell Equipment Spain
Physical Address: C/Iplacea Nº 10, Nave 2.2 P.I. Alcala Park, 28803 Alcalá de Henares, Madrid, Spain
Contact: Jesus Vivero
Mobile: +34-64 99 33 089
Tel: +34 91 879 60 19
Fax: +34 91 879 60 49
E-mail: lauriannec@fr.bellequipment.com
SWITZERLAND
Bell Switzerland (Bell Handling Systems and Bellinter Holdings)
Physical Address: Rue de Vevey 178, 1630 Bulle, SWITZERLAND
Contact: Jean-Christophe Cerouter or Pascal Gross
Tel: +41 26 913 00 11/2
Fax: +41 26 913 00 19
E-mail: beqch@bluewin.ch or pascal.beqch@bluewin.ch
UNITED KINGDOM
Bell Equipment U.K. LIMITED
Physical Address: Unit 6C, Graycar Business Park, Barton Turns, Barton-Under-Needwood, Burton-on-Trent,
DE13 8EN, UNITED KINGDOM
Contact: Neville Paynter
Tel: +44 1283 714259 (Direct)
Tel: +44 1283 714251 (Parts Direct)
Fax: +44 1283 712687
E-mail: cameronc@bellequipment.co.uk or general@bellequipment.co.uk
SOUTHERN AFRICA:
CAPE REGION:
CAPE TOWN
Bell Equipment Sales SA Limited
Physical Address: 28 Aviation Road, Phase 4, Airport City, Cape Town, 7475
Contact: John Collins (General Manager)
Mobile: +27 (0)82 495 9338
Tel: +27 (0)21 380 9000
Fax: +27 (0)21 380 9057
E-mail: maureenb@bell.co.za johnc@bell.co.za
EAST LONDON
Bell Equipment Sales SA Limited
Physical Address: 811 East Coast Resort Road, Meisies Halt, Gonubie, East London, 5200
Contact: Kassie van de Heever
Mobile: +27 (0)82 827 8050
Tel: +27 (0)43 732 1415 (Parts) or +27 (0)43 732 1473 (Admin &Technical Queries)
Fax: +27 (0)43 732 1435
E-mail: kassiev@bell.co.za
GEORGE
Bell Equipment Sales SA Limited
Physical Address: Pioneer Avenua Industria Pacaltsdrop, George, 6534
Contact: Ryan Britain
Mobile: +27 (0)82 334 2170
Tel: +27 (0)44 878 0930/1
Fax: +27 (0)44 878 0932
E-mail: karino@bell.co.za
PORT ELIZABETH
Bell Equipment Sales SA Limited
Physical Address: 349 Kempston Road, Korsten, Port Elizabeth, 6056
Contact: Gert Nelson
Mobile: +27 (0)82 657 1190
Tel: +27 (0)41 451 3202/4/6
Fax: +27 (0)41 451 3208
E-mail: lynneo@bell.co.za
NAMIBIA / WINDHOEK
IA Bell Equipment Sales SA Limited
Physical Address: 37 Lazarett Street, Ausspann Platz, Windhoek, Namibia
Contact: Johan van Wyk
Mobile: 081-250 2949
Tel: 264 61 226 021/2/3
Fax: 264 61 228 330
CENTRAL REGION:
JOHANNESBURG (GAUTENG)
Bell Equipment International Operations (BEIO)
Physical Address: Griffiths Road, Jet Park, 1459
Contact: Mike Dutton (Managing Director)
Mobile: +27 (0)82 821 1077
Tel: +27 (0)11 966 4949
Fax: +27 (0)11 966 4980
E-mail: sharona@bell.co.za
MIDDELBURG (MPUMALANGA)
Bell Equipment Sales SA Limited
Physical Address: 9 Tswelopele Street, Industrial Area, Middelburg, 1050
Contact: Aubrey Potgieter
Modile: +27 (0)83 629 1931
Tel: +27 (0)13 246 8900
Fax: +27 (0)13 246 1229
E-mail: rinas@bell.co.za
TZANEEN (LIMPOPO)
Bell Equipment Sales SA Limited
Physical Address: 1 Mangaan Street Tzaneen
Contact: Freddie Barnard (Branch Manager)
Mobile: +27 (0)82 335 9102
Tel: +27 (0)15 307 1129
Fax: +27 (0)15 307 3095
E-mail: freddieb@bell.co.za
COASTAL REGION:
SOUTH AFRICA
DURBAN
Bell Equipment Group (Chairman’s Office)
Physical Address: 75 Columbine Place, Ring Road Industrial Park, Durban North, 4000, Durban, 4000
Contact: Howard Buttery (Chairman)
Tel: +27 (0)31 569 1100
Fax: +27 (0)31 569 1108
E-mail: howardb@bell.co.za
EMPANGENI
Bell Equipment Sales SA Limited
Physical Address: No.1 Irvine Bell Drive, Old Mill Industrial, Empangeni, 3880
Contact: Mike Campbell (Branch Manager)
Mobile: +27 (0)82 784 1477
Tel: +27 (0)35 707 2500
Fax: +27(0)35 792 6516
E-mail: michaelc@bell.co.za
NELSPRUIT (MPUMALANGA)
Bell Equipment Sales SA Limited
Physical Address: 3 Christie Crescent, Vintonia 2, Nelspruit,1200
Contact: Leon van der Linde (Acting Branch Manager)
Mobile: +27(0)82 413 2469
Tel: +27 (0)13 755 2110/6
Fax: +27 (0)13 755 2117
E-mail: corries@bell.co.za
PIETERMARITZBURG
Bell Equipment Sales SA Limited
Physical Address: 7 Van Eck Place, Mkondeni, Scottsville, 3201, Pietermaritzburg, 3209
Contact: Les Lothain (Regional Manager)
Mobile: +27 (0)82 774 9937
Tel: +27 (0)33 386 9319
Fax: +27 (0)33 386 1837
E-mail: michellet@bell.co.za
UMHLALI
Bell Equipment Sales SA Limited
Physical Address: Lot 81, Sharks head, Industrial Park
Contact: Keith Hall (Customer Support Rep)
Mobile: +27 (0)82 774 0493
Tel: +27 (0)32 9470696
Fax: +27 (0)32 9472141
E-mail: selvann@bell.co.za
VRYHEID
Bell Equipment Sales SA Limited
Physical Address: Bloekom Street, Industrial Area
Contact: Cliff Glenn (Sales Representative)
Mobile: +27 (0)83 627 6459
Tel: +27 (0)34 981 5541
Fax: +27 (0)34 980 9752
E-mail: cliffg@bell.co.za
PONGOLA
Bell Equipment Sales SA Limited
Physical Address: Dewaal Street 233
Tel: +27 (0)34 413 1720
Fax: +27 (0)34 413 1735
SWAZILAND
Bell Equipment Sales SA Limited
Physical Address: Tambankulu Street, Plot 686, Matsapha, Swaziland
Contact: Charlie Boucher
Mobile: 00 268 7602 3795
Tel: +268 51 874 96/7
Fax: +268 51 874 98
E-mail: nicolienb@bell.co.za
BLOEMFONTEIN
Bell Equipment Sales SA Limited
Physical Address: 17 Dennis Pooley Street, Bloemfontein, 9300
Contact: Peter Wille (Branch Manager)
Mobile: +27 (0)82 854 2265
Tel: +27 (0)51 4327 855
Fax: +27 (0)51 4323 740
E-mail: yvetteo@bell.co.za or peterw@bell.co.za
KIMBERLEY
Bell Equipment Sales SA Limited
Physical Addess: 12 Hendrick Van Eck Street, Kimdustria, 8300
Contact: Aubrey Potgieter (General Manager)
Mobile: +27 (0)83 629 1931
Tel: +27 (0)53 841 0710/11/12/13
Fax: +27 (0)53 841 1940
E-mail: aubreyp@bell.co.za
WOLMARANSSTAD
Bell Equipment Sales SA Limited
Physical Address: 80 Kruger Street, Wolmaransstad, 2630
Contact: Bernard Niemand (Branch Manager)
Mobile: +27 (0)82 572 7881
Tel: +27 (0)18 596 2319
Fax: +27 (0)18 596 2855
E-mail: bernardn@bell.co.za
CENTRAL AFRICA:
OTHER AFRICA:
ZAMBIA
Bell Equipment Ltd - (Kitwe)
Physical Address: Kalulushi Business Park, Kalulushi, Kitwe, Zambia
Contact: Shaunn McCann (Sales Manager)
Mobile: +260 97 770 677
Tel : +260 2 731 557/8
Fax : +260 2 731 555
E-mail: shaunnmc@zm.bellequipment.com
ZIMBABWE
Bell PTA (PVT) Ltd (Harare)
Physical Address: 16 Erith Road, Willowvale, Harare, Zimbabwe
Contact: Charl du Toit
Mobile: +263-91 260 169
Tel: +263 4 661 061/090/125/181/418
Fax: +263 4 621 026
E-mail: charl@bellzim.co.zw
Due to BELL’s policy of continuous product improvement, the information contained in this
manual was correct up to the time of printing (Issue date of manual). Any changes after
this date will be distributed with associated bulletins.
Illustrations in this manual are pictorial representations of the component and are not
drawn to scale.
USERS COMMENT FORM
Should you, as user of this manual, have any suggestion for improving the manual, or you
find any errors or omissions, then we would like to know.
Please complete a facsimile of this form and hand it in to your nearest BELL Product Sup-
port Representative or post it directly to your nearest BELL Branch. Addresses are given
at the beginning of this manual.
Thank you for your cooperation.
YOUR COMMENTS, SUGGESTIONS, OR QUERIES:
MACHINE MODEL:
SERIAL NUMBER:
VIN:
DOCUMENT PART NUMBER AND ISSUE:
PAGE NUMBER:
NAME:
COMPANY:
TITLE:
ADDRESS:
TELEPHONE NUMBER:
CONTENTS
1
SECTION 1 : GENERAL INFORMATION
1-3
872196 - TH21D 13T TANDEM TRAILER - NOVEMBER 2011 REV A
1-4
LIST OF ABBREVIATIONS
Record the relevant information from the Technical Documentation Bulletins, Service Bul-
letins and Parts Bulletins into this manual as follows:-
i. Ensure the manual number (87xxxxx) reflected in the bulletin is the same as the
87xxxxx number on the front page of this manual.
ii. Carry out the instructions as detailed in the bulletin.
iii. Record the required information below.
iv. File the bulletins in numerical order in a suitable 3 or 4 ring binder.
To facilitate the ordering of parts, the following information is required to determine the
correct part for your BELL product.
Any other information which will assist us in getting the parts to you with the least amount
of trouble or delay should be given. This information will be noted and filed for future
reference.
1350
7358 7358
14716
1650
3285
480
2120
TD0006782
1-11
PIN CONFIGURATION
The principle means of identifying your Bell Equipment machine is by studying the VIN
number. The Vehicle Identification Number (VIN) structure for the Bell Equipment ma-
chines is as follows: (As an example, the B40D 6X6 manufactured at Richards Bay in
2001 has been used).
ii 411840 Is the machine type as presently used, i.e: for the B40D 6x6.
Note: Should the machine type/build number change due to a large upgrade
improvemnet - one which necessitates moving the machine from MKI to
MKII.
Note: This number is sequential to each product line and not to each product as
was tje case in the C series machines. This number will not return to zero
if there is a revision level change. It may occur that two ADT’s may have
the same sequential digits in its VIN, however this is not a problem as
they can be differentiated by their 400 number (machine type/build num-
ber).
The last 4 digits of the VIN will be used to identify the implementation of
engineering changes.
The VIN is stamped onto a 3mm plate which is welded to the engine chassis of the vehicle in the
same place that the serial number is stamped, in the articulation joint area.
35
13
12
34
11 32
5 14
3
9
31
6 2
4
2324
33 22
8 10 19
7 18 21
20
28 29
15
26
16 17
30
25 27
P001314
TD0006788
I Vin Series
Q
T PART
T DESCRIPTION REMARKS
E No. From:
Y
M To:
1 320220 AXLE ASSEMBLY (DUAL -1350 CRS)
2 100337 40 NUT, LOCK
3 150089 4 CUP, BEARING, OUTER
4 100348 40 NUT, TAPERED
5 200621 4 HUB
6 100262 40 STUD, WHEEL
7 100005 24 SCREW, SET, HEX
8 200623 4 HUB, CAP
9 100088 4 PIN, SPLIT
10 100342 4 NUT, CASTLE
11 150087 4 BEARING, CUP, INNER
12 200620 4 DRUM, BRAKE
13 100154 32 BOLT
14 290016 4 BRAKE ASSY
15 100319 32 NUT, NYLOC
16 100032 8 BOLT
17 160253 2 PLATE, RETAINER
18 180292 2 BEAM, WALKING
19 200622 4 STUB, AXLE
20 140172 2 SEAL, OIL
21 160231 2 BUSH, NYLON
22 160250 2 SHAFT, PIVOT
23 160232 2 BUSH, NYLON
24 160233 2 WASHER, THRUST
25 160255 1 PIN, SCREW
26 180280 1 HOUSING, PIVOT
27 100099 8 NUT, NYLOC
28 100744 8 BOLT
29 200036 5 GREASE NIPPLE
30 170163 4 PLATE, MOUNTING
31 150090 4 CONE, BEARING
32 150088 4 CONE, BEARING
33 200624 4 WASHER
34 140173 4 SEAL, OIL
35 200330 1 SLACK ADJUSTER
35
13
12
32 34
11
5 14
3
9
31
6 2
4
23 24
1033 19 22
8
7 18 21
20
36
28 29
15
26
16 17
30
25 27
P001314
TD0006788A
I Vin Series
Q
T PART
T DESCRIPTION REMARKS
E No. From:
Y
M To:
1 BN010664 AXLE ASSEMBLY (DUAL - 1350 CRS)
1 BN013940 AXLE ASSEMBLY (DUAL - 1450 CRS) (OPTION)
2 100337 40 NUT, LOCK
3 150089 4 CUP, BEARING, OUTER
4 100348 40 NUT, TAPERED
5 200621 4 HUB
6 100262 40 STUD, WHEEL
7 100005 24 SCREW, SET, HEX
8 200623 4 HUB, CAP
9 100088 4 PIN, SPLIT
10 100342 4 NUT, CASTLE
11 150087 4 BEARING, CUP, INNER
12 200620 4 DRUM, BRAKE
13 100154 32 BOLT
14 290016 4 BRAKE ASSY
15 100319 32 NUT, NYLOC
16 100032 8 BOLT
17 160253 2 PLATE, RETAINER
18 180292 2 BEAM, WALKING
18 180293 2 BEAM, WALKING (OPTION)
19 200622 4 STUB, AXLE
20 140172 2 SEAL, OIL
21 BN009854 2 BUSH, VESCONITE
22 160250 2 SHAFT, PIVOT
23 160232 2 BUSH, NYLON
24 160233 2 WASHER, THRUST
25 160255 1 PIN, SCREW
26 BN010665 1 HOUSING, PIVOT
27 100099 8 NUT, NYLOC
28 100744 8 BOLT
29 200036 5 GREASE NIPPLE
30 170163 4 PLATE, MOUNTING
31 150090 4 CONE, BEARING
32 150088 4 CONE, BEARING
33 200624 4 WASHER
34 140173 4 SEAL, OIL
35 200330 1 SLACK ADJUSTER
36 BN010563 2 SNAP RING
8,9 16
7 15
5 6 14
3 4 13
2 10
11 12
10
25
23 24
28
22
27
18
17
15
26
20 25
21
20
19 15
17
P001631
TD0008119
I Vin Series
Q
T
PART No. T DESCRIPTION REMARKS
E From:
Y
M To:
1 290016 BRAKE ASSEMBLY (DRUM)
2 200685 1 CIRCLIP, EXTERNAL
3 200683 1 PLATE, WASHER, GUIDE
4 200684 1 WASHER, BELLVILLE
5 200682 1 PLATE, GUIDE
6 200678 2 ROLLER
7 200679 2 PIN, ROLLER
8 200680 1 CAM, LH
9 200681 1 CAM, RH
10 200673 2 BUSH
11 200670 1 PLATE, TORQUE
12 200278 1 GREASE NIPPLE
13 200345 1 WASHER, THRUST
14 201650 1 CIRCLIP, EXTERNAL
15 200686 2 WASHER
16 100057 1 NUT, CLEAVELOCK
17 100041 2 PIN, SPLIT
18 200687 1 NUT, CASTLE
19 200692 1 NUT, SLOTTED
20 200672 2 PLATE, BACKING
21 200671 1 PIN, ANCHOR
22 200689 1 SPRING, RETURN
23 200688 2 SPRING, RETURN
24 200675 2 SPRING, POST
25 220109 2 BRAKE SHOE ASSY
26 200677 23 RIVET
27 200676 2 LINING
28 200674 2 BRAKE SHOE
P001687
TD0008120
I Vin Series
Q
T
PART No. T DESCRIPTION REMARKS
E From:
Y
M To:
1 260234 W/SET, 445/65R22.5
2 190174 1 WHEEL, 14X22.5
3 202960 1 TYRE, 445/65R22.5
4 202868 1 VALVE 90 D ANGLE SUPER
1
3
4 6 16 17
12 13
7 19
9 21
18
20
14
15
10 11
8 23 22
5 26 24
6 25
3
32 32
31
35 34 33
27
28
37 29
36 30
WARNING:
DISASSEMBLY OF THIS
COMPONENT IS
EXTREMELY DANGEROUS.
P000346
TD0008114
I Vin Series
Q
T
PART No. T DESCRIPTION REMARKS
E From:
Y
M To:
1 210052 1 BRAKE ACTUATOR ASSEMBLY
2 NSI 1 HOUSING
3 NSI 1 CLAMP, HALF
4 NSI 2 BOLT
5 NSI 2 NUT
6 NSI 1 CLAMP, HALF
7 NSI 2 BOLT
8 NSI 2 NUT
9 221437 1 KIT, SEAL, CENTRE SECTION
10 NSI 1 SPACER
11 NSI 1 SCREW
12 220211 1 DIAPHRAGM
13 224138 1 PISTON ROD ASSY
14 221436 1 SPRING, RETURN
15 NSI 1 COVER, END
16 100010 2 WASHER, FLAT
17 100035 2 NUT, NYLOC
18 100009 1 NUT
19 200093 1 CLEVIS
20 NSI 1 PIN
21 100069 1 PIN, SPLIT
22 221436 1 SPRING, RETURN
23 NSI 1 PIPE
24 NSI 1 SPACER
25 NSI 1 SCREW
26 220212 1 DIAPHRAGM
27 NSI 1 HEAD, PISTON
28 NSI 1 SPRING
29 NSI 1 SEAT, SPRING
30 NSI 1 COVER, END
31 NSI 1 HOSE
32 NSI 2 ELBOW
33 NSI 1 BOLT, RELEASE
34 NSI 1 WASHER
35 NSI 1 NUT
36 NSI 1 CAP, DUST
37 NSI 1 SCREW
11
9
8 12
4
7
6 15
5
3
2
17
10
13
14
16
P001630
TD0008115
I Vin Series
Q
T
PART No. T DESCRIPTION REMARKS
E From:
Y
M To:
1 210053 BRAKE ACTUATOR
2 NSI 1 COVER, END
3 220211 1 DIAPHRAGM
4 NSI 2 CLAMP, HALF
5 221438 1 ROD, PISTON
6 221436 1 SPRING
7 NSI 1 HOUSING
8 200093 1 CLEVIS ASSEMBLY
9 NSI 1 CLEVIS
10 NSI 1 PIN
11 100069 1 PIN, SPLIT
12 100009 1 NUT
13 100126 2 NUT, NYLOC
14 100049 2 WASHER, SPRING
15 NSI 2 BOLT
16 100314 2 NUT, NYLOC
17 NSI 1 PLUG
4
9
5
2 7
3 8
P001832
TD0008159
I Vin Series
Q
T
PART No. T DESCRIPTION REMARKS
E From:
Y
M To:
1 SOCKET HITCH (DRAWBAR, BOLT-ON / WELD-ON) 90MM
2 180339 1 HITCH, SOCKET, BOLT-ON UP TO 06.05.94
3 160327 1 CUP, BRONZE
4 200036 1 GREASE, NIPPLE
5 100105 4 BOLT
6 100057 4 NUT, CLEAVELOCK
7 181479 1 HITCH, SOCKET, WELD-ON FROM 06.05.94
8 160327 1 CUP, BRONZE
9 200036 1 GREASE, NIPPLE
3-2
RHMP - REAR HARNESS M PLUG
(MALE TERMINALS)
F
SPLICE 8
BROWN 1.5MM : RHMP-3 BROWN 1.5MM : INDL-2
BROWN 1.5MM : TCI-3
REV A
SECTION 3 : ELECTRICAL
ELECTRICAL SYSTEM
I Vin Series
Q
T
PART No. T DESCRIPTION REMARKS
E From:
Y
M To:
1 214337 1 FRONT HARNESS
3-4
(MALE TERMINALS)
FUNCTI
SPLICE 8
BROWN 1.5MM : RHMP-3 BROWN 1.5MM : INDL-2
BROWN 1.5MM : TCI-3
REV A
TD0
SECTION 3 : ELECTRICAL
ELECTRICAL CONNECTORS
I Vin Series
Q
T
PART No. T DESCRIPTION REMARKS
E From:
Y
M To:
1 214337 1 REAR HARNESS
26 21
28 K
24
J 29
M
15 14 D 25 L
1 5 8 25
3 3 6 7 A 7
10 9
11
B
C
RE6
N 13 10 19 C
B 16
2 3 4 3 6 7 A 7
8 12
16
17 17
3 30
18
E
I
20
H 21 20 3 31
G F
22
F 24
20 33 20 24 23
25 L 25
J
24 M K 29
27
J
28 26 21
TD0006784
I Vin Series
Q
T PART
T DESCRIPTION REMARKS
E No. From:
Y
M To:
1 214345 1 COUPLING, MALE,
2 214346 1 COUPLING, FEMALE
3 121077 6 UNION
4 204584 1 HOSE, RED
5 204585 1 HOSE, YELLOW
6 121526 2 CONNECT
7 122309 4 CONNECT
8 210064 2 FILTER UNIT
9 210678 1 VALVE
10 122316 1 CONNECT
11 121224 1 PLUG, HOLLOW
12 120358 1 ADAPTOR
13 120247 1 REDUCER
14 122314 1 TEE
15 122317 1 ELBOW
16 203897 2 RESERVOIR
17 200318 4 MTG
18 120166 2 VALVE, DRAIN
19 120399 1 PLUG
20 121080 4 ELBOW
21 121083 3 T-PIECE
22 122313 1 ELBOW
23 212070 1 VALVE
24 122315 4 CONNECT
25 121525 6 ELBOW
26 122312 3 CONNECT
27 122310 1 ELBOW
28 210052 2 ACTUATOR
29 210053 2 ACTUATOR
30 204586 1 COUPLING
31 204587 1 COUPLING
32 212071 1 VALVE
A 244174 2 HOSE
B 244269 2 HOSE
C 244268 1 HOSE
D 244262 1 HOSE
E 244267 1 HOSE
F 244264 2 HOSE
G 244265 1 HOSE
H 244266 1 HOSE
I 244263 1 HOSE
J 244236 4 HOSE
K 244240 2 HOSE
L 244235 2 HOSE
M 244170 2 HOSE
N 244239 1 HOSE
8
26
9
2 10 25
3
33 24
23
22
32 17
4 21
18
5
31
6 20 19
30
29
16
7 28
15
27 14
13
12
11
P000257
TD0008116
I Vin Series
Q
T PART
T DESCRIPTION REMARKS
E No. From:
Y
M To:
1 210678 1 RELAY EMERGENCY VALVE
2 100189 4 BOLT
3 100065 4 WASHER, SPRING
4 NSI 1 COVER, TOP
5 * 1 O RING, PISTON
6 NSI 1 PISTON, RELAY
7 NSI 1 SPRING, PISTON RETURN
8 NSI 1 SEAT, EMERGENCY PISTON
9 * 1 SEAL, EMERGENCY PISTON
10 * 1 O RING
11 NSI 1 SCREW
12 NSI 1 WASHER, DIAPHRAGM
13 * 1 DIAPHRAGM, EXHAUST
14 NSI 3 BOLT
15 100065 3 WASHER, SPRING
16 NSI 1 COVER, BOTTOM
17 * 1 VALVE, NON RETURN
18 * 1 SPRING, COMPRESSION
19 * 1 O RING
20 * 1 SPRING, COMPRESSION
21 NSI 1 CIRCLIP, INTERNAL
22 NSI 1 RING, RETAINING
23 NSI 1 GUIDE, VALVE
24 NSI 1 SPRING, VALVE
25 NSI 1 RETAINER, VALVE
26 * 1 VALVE, INLET/EXHAUST
27 * 1 O RING
28 NSI 1 PISTON, EMERGENCY
29 * 1 O RING
30 NSI 1 FILTER, ADAPTOR
31 NSI 1 PLUG
32 NSI 1 PLUG
33 NSI 1 BODY, VALVE
34 220958 1 KIT, REPAIR, RELAY EMERGENCY VALVE INCLUDES ITEMS MARKED *
5-1
SECTION 5 : FRAME AND BODY
FRAME AND BODY - A
11
2
21
22
12
1
4
19
20 21
9
8
21
8 20
10 7
17 18
13 3
15
14
13
17 5
16
6
TD0006785
I Vin Series
Q
T PART
T DESCRIPTION REMARKS
E No. From:
Y
M To:
1 184606 1 CHASSIS, TRAILER, TANDEM
2 180339 1 SOCKET, HITCH, 90MM, BOLT ON
3 180340 1 BALL, HITCH, 90MM
4 260234 W/SET, 445/65R22.5 (SEE WEEL ASSEMBLY OPTIONS - PG 2-7)
4 226175 W/SET, 445/65R22.5 (SEE WEEL ASSEMBLY OPTIONS - PG 2-7)
4 266189 W/SET, 445/65R22.5 (SEE WEEL ASSEMBLY OPTIONS - PG 2-7)
4 BN013950 W/SET, 17.5R25 (SEE WEEL ASSEMBLY OPTIONS - PG 2-7)
5 170377 1 PLT, HOOK, LOCK, TRAILER
6 320665 1 ASSY, AXLE, 1350 CRS
7 226988 1 LANDING-LEG, JOST, D200T
8 100010 20 WASHER
9 100415 10 NUT
10 100146 10 BOLT
11 100105 4 BOLT
12 100057 4 NUT
13 101318 8 WASHER
14 100180 4 NUT
15 100172 4 BOLT
16 100162 2 BOLT
17 100532 4 WASHER
18 100323 2 NUT
19 200318 2 MTG BAND
20 100185 2 BOLT
21 100537 4 WASHER
22 100321 2 NUT
3
5
4
6
7
6
7
TD0006791
I Vin Series
Q
T PART
T DESCRIPTION REMARKS
E No. From:
Y
M To:
1 184606 1 CHASSIS, TRAILER, TANDEM
2 184586 1 DECK, PLATE, FRONT
3 184605 1 DECK, PLATE, MID
4 184587 1 DECK, PLATE, REAR
5 100146 12 BOLT
6 100010 24 WASHER
7 100415 10 NUT
8
3 9
7
4
5
4
5
9
10
4 2
5
5 5
6
7
1
5
6
TD0006792
I Vin Series
Q
T PART
T DESCRIPTION REMARKS
E No. From:
Y
M To:
1 184606 1 CHASSIS, TRAILER, TANDEM
2 192095 4 BUNK, STEPPED
2 BN013955 4 BUNK, STEPPED (OPTION)
3 260802 8 TYNE, 1350 MM
4 100158 16 BOL, HEXHD
5 100423 32 WASHER
6 100323 16 NUT
7 184679 1 MUDGUARD, LHS
7 BN013951 1 MUDGUARD, LHS (OPTION)
8 184680 1 MUDGUARD, RHS
8 BN013951 1 MUDGUARD, RHS (OPTION)
9 100030 32 SCREW, HEXHD
10 100304 64 WASHER
11 100314 32 NUT
4
1
WARNING WARNING
STAY CLEAR
Operator may
reverse the
machine.
207 337-B
2
WARNING BELL TRAILERS
COLD INFLATION PRESSURES
SPRING UNDER Consult tyre companies for site-specific pressures.
PRESSURE
FRONT REAR
MAKE MODEL SIZE PSI KPA PSI KPA
MICHELIN XZY3 445/65 R22.5 130 900 130 900
BRIDGESTONE R164 445/65 R22.5 130 900 130 900
207 350 - B INFINITY 445/65 R22.5 130 900 130 900
TRELLEBORG AR-01 445/65 R22.5 116 800 116 800
277035
WARNING
3 Crushing injury may result 5
in hitch area if machine is
tu r n e d o r reverse d .
WARNING
207349
266628
TD0006793
I Vin Series
Q
T PART
T DESCRIPTION REMARKS
E No. From:
Y
M To:
266628 1 KIT
1 207337 1 DECAL, VISIBILITY WARNING, D#
2 207350 1 DECAL, SPRING PRESSURE, ADT, D#
3 207320 2 DECAL, B&W BELL LOGO
4 277035 2 DECAL, TYRE PRESSURE, TRL
5 214362 2 DECAL, CRUSHING INJURY
6 207349 1 DECAL, COMPRESSED AIR