Professional Documents
Culture Documents
Kelas : P4
NIM : F3401211102
Dosen/Asisten Dosen : AGS/LPA
Regenerating model.
Command:
Command: Regenerating model.
Command:
Command: _box
Specify first corner or [Center]:
Specify other corner or [Cube/Length]: @110,188
Command:
Command:
Command: _cylinder
Specify center point of base or [3P/2P/Ttr/Elliptical]:
Specify base radius or [Diameter] <15.0000>: 15 Specify height or [2Point/Axis
endpoint] <12.0000>: 20
Command:
Command:
Command: _cylinder
Specify center point of base or [3P/2P/Ttr/Elliptical]:
Specify base radius or [Diameter] <15.0000>: 8
Command: MOVE
Select objects:
Command: MIRROR
Select objects:
Specify first point of mirror line:
Specify second point of mirror line:
Erase source objects? [Yes/No] <No>: N
Command:
Command:
Command: _cylinder
Specify center point of base or [3P/2P/Ttr/Elliptical]:
Specify base radius or [Diameter] <8.0000>: 23
Command: MOVE
Select objects: 1 found
Select objects:
Command:
Command:
Command: _cylinder
Specify center point of base or [3P/2P/Ttr/Elliptical]:
Specify base radius or [Diameter] <23.0000>: 15
Command:
Automatic save to C:\Users\DJOKOS~1\AppData\Local\Temp\
Drawing2_1_20851_d01a776a.sv$ ...
Command:
Command: UCS
Command:
Command:
Command: _extrude
Current wire frame density: ISOLINES=4, Closed profiles creation mode = Solid
Command:
Command:
Command: _move
Select objects: 1 found
Select objects:
Command:
Press ESC or ENTER to exit, or right-click to display shortcut-menu.
Regenerating model.
Command:
Command:
Command:
Command: _cylinder
Specify center point of base or [3P/2P/Ttr/Elliptical]:
Specify base radius or [Diameter] <42.0000>: 26
Command: SLICE
Command:
Command:
Command: _.undo Current settings: Auto = On, Control = All, Combine = Yes, Layer
= Yes
Enter the number of operations to undo or [Auto/Control/BEgin/End/Mark/Back] <1>:
1 INTELLIZOOM
Command: SLICE
Command:
Command: _ai_selall Selecting objects...done.
Command: TRIM
Command:
Command: _.undo Current settings: Auto = On, Control = All, Combine = Yes, Layer
= Yes
Enter the number of operations to undo or [Auto/Control/BEgin/End/Mark/Back] <1>:
1 TRIM
Command:
Command:
Command: _.undo Current settings: Auto = On, Control = All, Combine = Yes, Layer
= Yes
Enter the number of operations to undo or [Auto/Control/BEgin/End/Mark/Back] <1>:
1 AI_SELALL GROUP
Command:
Command:
Command: _.undo Current settings: Auto = On, Control = All, Combine = Yes, Layer
= Yes
Enter the number of operations to undo or [Auto/Control/BEgin/End/Mark/Back] <1>:
1 SLICE
Command:
Command:
Command: _.undo Current settings: Auto = On, Control = All, Combine = Yes, Layer
= Yes
Enter the number of operations to undo or [Auto/Control/BEgin/End/Mark/Back] <1>:
1 INTELLIZOOM
Command:
Command:
Command: _.undo Current settings: Auto = On, Control = All, Combine = Yes, Layer
= Yes
Enter the number of operations to undo or [Auto/Control/BEgin/End/Mark/Back] <1>:
1 INTELLIZOOM
Command:
Command:
Command: _.undo Current settings: Auto = On, Control = All, Combine = Yes, Layer
= Yes
Enter the number of operations to undo or [Auto/Control/BEgin/End/Mark/Back] <1>:
1 SLICE
Command: SLICE
Command:
Command:
Command: _.undo Current settings: Auto = On, Control = All, Combine = Yes, Layer
= Yes
Enter the number of operations to undo or [Auto/Control/BEgin/End/Mark/Back] <1>:
1 SLICE
Command: SLICE
Command:
Command:
Command: _.undo Current settings: Auto = On, Control = All, Combine = Yes, Layer
= Yes
Enter the number of operations to undo or [Auto/Control/BEgin/End/Mark/Back] <1>:
1 SLICE
Command: SLICE
Command: FILLET
Command:
Command: _FILLETEDGE
Radius = 1.0000
Select an edge or [Chain/Loop/Radius]: R
Command:
Command: _.undo Current settings: Auto = On, Control = All, Combine = Yes, Layer
= Yes
Enter the number of operations to undo or [Auto/Control/BEgin/End/Mark/Back] <1>:
1 FILLETEDGE GROUP
Automatic save to C:\Users\DJOKOS~1\AppData\Local\Temp\
Drawing2_1_20851_d01a776a.sv$ ...
Command:
Command:
Command:
Command: _FILLETEDGE
Radius = 1.0000
Select an edge or [Chain/Loop/Radius]: R
Command:
Command:
Command: _union
Select objects: *Cancel*
Command:
Command: _union
Select objects: Specify opposite corner: *Cancel*
0 found
Select objects: 1 found
Select objects:
Command:
Command:
Command: _subtract Select solids, surfaces, and regions to subtract from ..
Select objects:
Select solids, surfaces, and regions to subtract ..
Select objects: 1 found
Select objects:
Command: UCS
Command:
Command:
Command: _line
Specify first point:
Specify next point or [Undo]: 90
Command:
Command: POLYLINE
PLINE
Specify start point:
Current line-width is 0.0000
Specify next point or [Arc/Halfwidth/Length/Undo/Width]: @55,0
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,-45
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: _tan to
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]:
Command: MIRROR
Select objects: 1 found
Select objects:
Specify first point of mirror line:
Specify second point of mirror line:
Erase source objects? [Yes/No] <No>: N
Command: TRIM
Automatic save to C:\Users\DJOKOS~1\AppData\Local\Temp\
Drawing2_1_20851_d01a776a.sv$ ...TRIM
TRIM
Command: TRIM
Command: TRIM
View is not plan to UCS. Command results may not be obvious.
Current settings: Projection=UCS, Edge=None, Mode=Quick
Select object to trim or shift-select to extend or
[cuTting edges/Crossing/mOde/Project/eRase]: *Cancel*
Command: TRIM
View is not plan to UCS. Command results may not be obvious.
Current settings: Projection=UCS, Edge=None, Mode=Quick
Select object to trim or shift-select to extend or
[cuTting edges/Crossing/mOde/Project/eRase]:
Select object to trim or shift-select to extend or
[cuTting edges/Crossing/mOde/Project/eRase/Undo]:
Select object to trim or shift-select to extend or
[cuTting edges/Crossing/mOde/Project/eRase/Undo]:
Command: JOIN
Select source object or multiple objects to join at once: 1 found
Select objects to join: 1 found, 2 total
Select objects to join: 1 found, 3 total
Select objects to join:
4 segments joined into 1 polyline
Command:
Command:
Command: _extrude
Current wire frame density: ISOLINES=4, Closed profiles creation mode = Solid
Select objects to extrude or [MOde]: _MO Closed profiles creation mode
[SOlid/SUrface] <Solid>: _SO
Select objects to extrude or [MOde]: 1 found
Select objects to extrude or [MOde]:
Specify height of extrusion or [Direction/Path/Taper angle/Expression] <-110.0000>:
15
Command:
Command:
Command: _cylinder
Specify center point of base or [3P/2P/Ttr/Elliptical]:
Specify base radius or [Diameter] <26.0000>: 11
Specify height or [2Point/Axis endpoint] <-15.0000>: 15
Command:
Command:
Command: _subtract Select solids, surfaces, and regions to subtract from ..
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects:
Select solids, surfaces, and regions to subtract ..
Select objects: '_.zoom
>>Specify corner of window, enter a scale factor (nX or nXP), or
[All/Center/Dynamic/Extents/Previous/Scale/Window/Object] <real time>: _e
Resuming SUBTRACT command.
Select objects: '_.zoom
>>Specify corner of window, enter a scale factor (nX or nXP), or
[All/Center/Dynamic/Extents/Previous/Scale/Window/Object] <real time>: _e
Resuming SUBTRACT command.
Select objects: *Cancel*
Command:
Command: _.undo Current settings: Auto = On, Control = All, Combine = Yes, Layer
= Yes
Enter the number of operations to undo or [Auto/Control/BEgin/End/Mark/Back] <1>:
1 SUBTRACT GROUP
Command:
Command:
Command: _subtract Select solids, surfaces, and regions to subtract from ..
Select objects: 1 found
Select objects:
Select solids, surfaces, and regions to subtract ..
Select objects: 1 found
Select objects:
Command:
Command:
Command: _cullingobj
Enter new value for CULLINGOBJ <1>: 0
Command:
Command:
Command:
Command:
Command:
Command:
Command: _.erase 1 found
Command: MOVE
Select objects: 1 found
Select objects:
Specify base point or [Displacement] <Displacement>:
Specify second point or <use first point as displacement>:
Command:
Command:
Command: _union
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects:
Command:
Command:
Command:
Command:
Command: