Professional Documents
Culture Documents
If you want to remove burred or slivered edges, what tools should be used?
Select one:
Hacksaw
Chisel
File
Snipe
When technician transfers dimensions from a paper pattern directly on the metal,
what should technicians do?
Select one:
He/she had to tap it lightly with a soft face hammer
Select one:
Socket wrench
Spanner wrench
Allen wrench
Select one:
Secondary Standard
Tertiary Standard
Primary Standard
Question 5 Complete Marked out of 1.00
Select one:
a person should be in the cockpit to watch for obstructions.
persons should be stationed at the nose, each wingtip, and the empennage at all times.
persons should be never stationed at the nose, each wingtip, and the empennage at all times.
If you want to drilling around flammable material, what type of drill should be used?
Select one:
Electric power drills
From the picture below, which one is shows flutes, shank and cutting edge?
Select one:
A drill one sizes smaller than the rivet shank diameter.
Select one:
checked for fracture
oiled
Select one:
Heavy duty.
Small work.
Light work.
Select one:
be sure the tool switch is in the off position
For pulling locknut and safety wire , the pliers we normally used is
Select one:
Duckbill plier
Linemen’s plier
These are the following rules that will make your job easier and safer, except
Select one:
Keep each tool in new stowage place
Select one:
65o – 85o
63o – 85o
65o – 88o
60o – 80o
Question 15 Complete Marked out of 1.00
When technician want to shaping thin metal parts without denting them, what type
of hammer should be used?
Select one:
Ball peen hammer
Straight hammer
Mallet
Riveting hammer
Select one:
After the first few strokes, make each stroke as long as the hacksaw frame will allow
Indicate the starting point by nicking the surface with the edge of a punch to break any sharp corner
that might strip the teeth
Hold the saw at an angle that will keep at least two teeth in contact with the work at all times
Adjust tension of the blade in the frame to prevent the saw from buckling and drifting
Question 17 Complete Marked out of 1.00
If the aircraft must taxi straight ahead, what signal should be given by taxi
signalman?
Select one:
Signal C.
Signal D.
Signal B.
Signal A.
Question 18 Complete Marked out of 1.00
What type of shank drill is usually used in machine shop drilling machines?
Select one:
C
A and B
If you want to remove burred or slivered edges, what tools should be used?
Select one:
Hacksaw
Chisel
File
Snipe
Question 20 Complete Marked out of 1.00
Select one:
Secondary Standard
Tertiary Standard
Primary Standard
The clearance between the piston rings and the ring lands is measured with a
Select one:
micrometer caliper.
dial gauge.
thickness gauge.
depth gauge.
When cutting solid stock aluminum, bearing metal, tool steel, and cast iron, what
type of blades should be used?
Select one:
A blade with 24 teeth per inch
Involving such matters as to the using of the correct dosage or proportions when
mixing compounds, using only as much material as required for a specific task and
to the keeping in stock of only sufficient materials and thus avoiding 'lifed' items
reaching their expiry dates before being used, can control involve by
Select one:
Economy
Safety
Management
Human factor
What should be the included angle of a twist drill for hard metal?
Select one:
60o.
118o
100o
90o
Select one:
Testing Airspeed Indicator
What is the name of the filling method shown in the following picture?
Select one:
Lathe filling
Cross filling
Filling curves
Draw filling
What should be done by aircraft maintenance technicians when the work shifts has
changed? EXCEPT.
Select one:
The outgoing shift technician should inform the work that has been done to the next shift
technician.
The outgoing shift technician should inform the work that has not been done to the next shift
technician.
The outgoing shift technician should prepare the equipment to be used by the next shift technician.
The outgoing shift technician should remove and store correctly the personal tools.
Question 28 Complete Marked out of 1.00
Select one:
ratchet screwdriver can be set to turn the screw either clockwise or counterclockwise
rachet screwdriver can not be set to turn the screw either clockwise or counterclockwise
Select one:
A = Starting punch, C = Center punch, F = Pin punch
Select one:
Make own notes about the tools used and not used
Provide inventory list in every toolbox, check it before and after work
Select one:
Grease
Copper
Oil
Paint
From the equipment below, which are included in the equipment to maintain safety
Select one:
Picture F and B.
Picture A and E.
Picture B, E and F.
Picture C, E and F.
Question 33 Complete Marked out of 1.00
There should be a number from 0 to 4 in Material Safety Data Sheet, what does it
means?
Select one:
The level of safety, 0 represents the material is very hazardous, 4 means that the material is little or
no hazard to the user
The level of hazard, 0 represents little or no hazard to the user, 4 means that the material is very
hazardous
The level of safety, 0 represents little or no hazard to the user, 4 means that the material is very
hazardous
The level of hazard, 0 represents the material is very hazardous, 4 means that the material is little or
no hazard to the user
Select one:
Rejected sticker
Decent sticker
Calibration record
Question 35 Complete Marked out of 1.00
Hacksaw has two types of blade, hard blade and flexible blade. What is function of
these blade?
Select one:
An all hard blade is best for sawing hollow shapes and a flexible blade is usually best for sawing
brass
An all hard blade is best for sawing brass material and a flexible blade is usually best for sawing cast
iron
An all hard blade is best for sawing brass and a flexible blade is usually best for sawing hollow
shapes
An all hard blade is best for sawing thin cross section material and a flexible blade is usually best for
sawing brass
Select one:
Carbon steel and stainless steel
Select one:
Position D.
Position C.
Position A.
Position B.
Question 38 Complete Marked out of 1.00
Select one:
65o – 88o
60o – 80o
65o – 85o
63o – 85o
Select one:
Normal material
Hazardous
Deadly
Extreme danger
You are involved with a fire caused by magnesium swarf. What type of extinguisher
should you use to deal with the fire?
Select one:
CO2 extanguisher
Water extinguisher
Foam extanguisher