Professional Documents
Culture Documents
2216 Ba Gray
2216 Ba Gray
EIP¡ryAdhesive
OneBlA Graü. 22l6BlATan NS .2216 B/A Translucent
\-______---------,
Product Description 3M'" Scotch-Weld"" Epoxy Adhesive 2216 B/A Gray, Tan NS and Translucent are
flexible, twG.part, room temperature curing epoxies with high peel and shear strengths.
Advantages . Excellent for bonding many metals, woods, plastics, rubbers, and masoory products.
§pical Uncured Note: The following technical information and data should be considered representative
Physical Prop€rties or typicál only and should not be used for specilication purposes.
Product 2216 BIA Gray 2216 B/A Tan NS 2216 B/A Translucent
Mix Batio: (by weight) 5 parts 7 parts 5 parts 7 parts 1 part 1 part
Mix Ratio: (by volume) 2 parts 3 parts 2 parts 3 parts 1 part 1 part
Work Life:
10O g Mass @ 75'F (24"C) 90 minutes 90 minutes 120 m¡nutes 120 m¡nutes 120 minutes 120 m¡nutes
Scotch-Weld"
Epoxy Adhesives
22l6Bl{Gray.2216 B/A Tan NS.2216 B/A Translucent
D¡ss¡pation Factor 73'F (23'C) 0.112 Measured @ 1.00 KHz 0.'119 @ 1 KHz
llandling/Curing 3. For maximum bond shength, apply product evenly to both surfaces to be joined.
lnÍormtüon (continued) 4. Appücation to the subshates should be made within 90 minutes. Larger quantities
and/or higher temperatures will reduce this working time.
5. Join the adhesive coated surfaces and allow to cure at 60oF (16oC) or above until
fhm. Heat, up to 20O"F (93"C), will speed curing.
6. The following times and temperatues will result in a full cure:
7. Keep parts from moving until handling strength is reached. Contact pressure is
necessary. Maximum slrar strength is obtained with a 3-5 mil bond line.
Maximum pe€l strenglh is obfahed witl a 17-25 mil bond line.
8. Excess uncured adhesive can be cleaned up with ketone qpe solvents.*
Adhesive Coverage: A 0.ffi5 in. thick bondline witl §pically yield a coverage of
320 sq. flgallon
Application and These products may be applied by spaflrla, trowel or flow equipment.
Equipment Suggestions l\ryo-paft mixing/proportioning/dispersing equipment is available for intermitüent or
production line use. These systems a¡e ideal because of their variable shot size and
flow rate characteristics and are adaptable to many applications.
Surface heparation For high strenglh structural bonds, paint, oxide films, oils, dust, mold release agents
and all other surface contaminants must be completely removed Howeveq the
amoult of surface preparation directly depends on the required bond strength and the
environmental aging resistance desired by user.
The following cleaning methods are suggested for common surfaces.
-3-
Scotch-Weld-
Epoxy Adhesives
22168/AGray'2216 B/A Tan NS'2216 B/A Translucent
Preparation
Surface Aluminum (Chemical Etch)
(continuul) Aluminum al§s may be chemically cleaned and erched as per ASTM D 2651. This
procetlure states to:
1. Alkaline Degrease - Oakite 164 solution (9-11 ozlgal of water) at 190'F t 10'F
(88"C ¿ 5"C) for 10-20 minutes. Rinse immediately in large quanlities of cold
running water.
2. Optimized tr?L Etch Solulion (l liter):
lt{aterisl Amount
Distilled Water 700 ml plus balance of liter (see below)
Sodium Dichromate 28 to 67.3 grams
Sulf¡ric Acid 287.9 o 310.0 grams
AluminumChips 1.5 gams/liter of mixed §olution
Plastics/Rubber
1. Wipe with isopropyl alcohol.*
2. Abrade using fine grit abrasives (180 grit or finer).
3. Wipe with isopropyl alcohol.+
Glass
1. Solvent wipe surface using acetone or MEK.*
2. Apply athin coating (0.0001 in. or less) of 3Mru Scotch-WeldrM Struco[al
Atlhesive Primer EC-3901 to the glass surfaces to be bonded and allow the primer
!o dry a minimum of 30 minutes @ 75"F (24"C) before bonding.
+Note: When using solvents, extinguish all igniüon sources and follow the
manufacturer's precauüons and directions for use. Use solvents in
accordance with local regulations.
-4-
Scotch-Weld'"
Epoxy Adhesives
22l6BlAGray' 2216 B/A Tan NS'2216 B/A Translucent
Adhesive
§pical A. \pical Shear Properties on Etched Aluminum
Performance ASTM D 1002
Characteristics Cue: 2 hours @ 150 r 5"F (66"C t 2'C), 2 psi pressure
Shear Modulus
Test Temperature (Torsion Pendulum Method)
-148"F G100"C) 398,000 psi (2745 MPa)
-76'F C60"C) 318,855 psi (2199 MPa)
-40"F G40'C) 282,315 psi (1947 MPa)
Test Temperature 2216 B/A Gray 2216 B/A Tan NS 2216 B/A Trans.
Adhesive Adhesive Adhesive
75.F (24"C\ 25 25
-5-
Scotch-Weld'"
Epoxy Adhesives
221681AGruy.2216 B/A Tan NS.2216 B/A Translucent
Tap Water @ 75'F (24'C) '14 days 3120 psi 3250 psi
30 days 2942 psi 2700 psi 1950 psi
90 days 2075 ps¡
Air @ 300'F (149"C) 40 days 4930 psi 4450 psi 3500 psi
Anti-ic¡ng Fluid @ 75'F (24'C) 7 days 3300 ps¡ 3050 psi 2500 psi
Hydraulic Oil@ 75'F (24'C) 30 days 2500 ps¡ 3500 psi 2500 psi
-6-
Scotch-\{eld'"
Epoxy Adhesives
22l6BlAGray.2216 B/A Tan NS.2216 B/A Translucent
§pical Ailhesive E. Overlap Shear Shength on Abraded Metals, Plastics, and Rubbers.
ll{gfl=^- Overlap shear strengths were measwed on 1" x 1/2" overlap specimens. These
:^ifT:f;"*
\conwuea)
bonds were made individually using 1" by 4" pieces of subidte (Tesr€d per
ASTM D loo2).
The thickness of the substrates were: cold rolled, galvanized and stainless ste€l -
0.056-0.062", copper - 0.032", brass - 0.036", rubbers - 0.125", plastics - 0.125".
All surfaces were prepared by solvent wiping/abmding/ solveDt wiping.
The jaw separation rate used for testing was 0. 1 in/min for metals, 2 in/min for
plastics, and 20 inlmin for rubbers,
Storage and Shelfl,ife Storage: Store products at 60-80'F (16-27oC) for maximum storage life.
Shelf Life: When stored at the recommended temperatures in üe original, uno¡rened
containers, the 3M St¿ndard shelf life is two years from date of shipment
from 3M.
Note 2216 B/A is identical to 3MrM Scotch-WeldrM Epoxy Adhesive EC-2216 B/A in
chemical composition. EC-2216 B/A has been labeled, packaged, tested, and
certified for aircraft and aerospace applications. 2216 B/A may be used for aircraft
and aerospace applications if proper Certificates of Test have been issued and
material meets all aircraft manufacturer's specification requirements.
-'7 -
Scotch-Weld*
Epoxy Adhesives
22l6Bl{Gray.2216 B/A Tan NS'2216 B/A Translucent
Prccautionary Befer to Product Label and Mate*, Safety Data Sheel br Health and Safety lnformal¡on beÍoro using this
prod0cl.
Information
For Additional To request addit¡onal producl information or to arrange for sales assistance, call ioll lree 1.800-362-3550
or vis¡l www.SM.com/adhes¡ves. Addrggs correspondence to: 3M Eng¡neered Adhes¡v$ Oivis¡on, 3M
Information Center, Bulld¡ng 220-7E{1, St, Paul, MN 55144-1000. Our fax number ¡s 651-733-9175. ln Canada,
phone: 'l €00-364-352. ln Puerlo Bico, phone: 1-787-75G3000. ln Mex¡co, phone: 52.70.04-00.
Important Notice 3M MAKES NO WARRANTIES, EXPRESS OR II\4PLIED, INCLUDING, BUT NOT LIMIÍED TO, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. User ¡s
respons¡ble fordetermining whelher the 3M product is litlor a pañ¡oular purpose and suitable Ior user's
method of applicatioñ. Please remember that many faclors can affect the use and perlormance of a 3l\¡
produot in a parl¡cular applicat¡on. ThE mater¡als lo be bonded with the producl, lhe surlace preparal¡on
of those maleñals, the producl selecled for use, the condii¡ons ¡n which the product ¡s u9ed, and the t¡me
and env¡ronmental cond¡üons ¡n wh¡ch the product ¡s expected to perform are among the many laclors
that can afl€cl the use and performanc€ of a 3M prcducl- G¡ven lhe variely ol factors that can affect the
use and perrormañce ol a 3M produc{, some of wh¡ch are unk¡uely within the usér's kno{vledge and
contro!, it is essenl¡al that the user e\.aluate the 3M product to determ¡ne whether il is f¡t lor a particular
purpose and suitable for the useis method of appl¡cation.
Limitation of Remedies lf the 3t!,1 product ¡s proved lo be defec{v€, THE EXCLUSIVE BEMEDY AT 3l\,1'S OPTION, SHALL BE TO
BEFUNDTHE PURCHASE PBICE OF OR TO BEPAIB OR BEPLACE THE DEFECÍIVE 3M PBODUCT
and Liability 3M shall not olherw¡se be l¡ade úcr loss or damage§, whether d¡rect, indirecl spec¡al, ¡ncidental, or
corsequenl¡al, regardless of the legal lheory asserted, ¡nclud¡ng, hrt not lim¡ted to, conlract, negl¡gence,
wananty, or str¡ci l¡abil¡ty.
This Engino€rod Adhsiws Divi§ioi prodrJcl wea menufáclur€d und6r 6 3M quelily sysl€m regisl€rod to ISO g0@ standards.
gt,l
Engbeered Adh€sives Division Reqrkd Paper
3M Crnter Building 220-78-01 40% pn-cotlrwner
St. Paut, MN 55144-1000 IM post-consune¡ @¡\r 2002 78{9@-95a3.7
-8-
3MEC-2216 - 3M Scotch-Weld Epoxy Adhesive Págtna 1 de 2
ffiffi
S;$***
Pr0duct§ §ervices
Save up to 18olo on 3
3M EC-2216 - 3M Scotch-Weld E¡
Scotch-Weld
Adhesives in Duo- A h¡ghly flexible two-part adhes¡ve that cures at roo
Pak Cartr¡dges provides high strength bonds w¡th except¡onal shear
rubber, metal, wood, most plast¡cs and masonry prc
< Back To Structural
Adhes¡ves . Dala.Sheet
Scotch-Weld Acryl¡c
Adhesives M¡x Rat¡o (volume) B:A 2.3
scotch-weld Epoxy Approximate Viscosity 75oF 40000 _ 800(
Adhes¡ves (24oc) (cPs)
Scotch-Weld Urethane Approximate workl:fe at 75oF 90 minutes
Adhes¡ves (24oc)
Averagé T-Peel at 75oF (24oC) 25
Select a Category: (Prw)
Overlap Shear Strength PSI - 3ooo
3M Products 67oF (-55.c)
Overlap Shear Strength PSI 75o 3200
F (24oC)
Industrial Pressure
Sensitive Tape shear Strength
overlaD Shear
Overlap Strenqth PSI
1800F (820C)
Rest¡ictions None
llaskants
Purchase In Bulk
Overstock Products gI
Save 10go More on Sales Above $5OO
Silicone Rubber
Products Qty Un¡t Descr¡ption cotor Items/
_
gase er, 3i
UPCi 21200566592 Weight: 2.8 lb
Spec¡als of the
Month , ,aut" 43 m¡l Duo-Pak Gray 12 Each $l
http://www.tapecase.com/p.14.513m-ec-2216-3m-scotch-weld-epoxy-adhesive.aspx 051t212008
3MEC¿216 - 3M Scotch-Weld Epoxy Adhesive Página 2 de 2
http://wr,{w.tapecase.com/p.14.513m-ec-2216-3m-scotch-weld-epoxy-adhesive.aspx 05/l2l2oo8