Professional Documents
Culture Documents
SPECIFACATIONS
1/12 SCALE COMBAT
DESIGNED & DRAWN BY STEVE HERGETT
CANOPY
FORMER
1/"BALSA
FORMER 2A
template FORMER 1A
1/4" PLY
3/16"
balsa 3/16" 3/16" Balsa
grain
balsa SEE SECTION VIEW
grain
trim to
3/16" up & add balsa block to underside of crutch
conform
to canopy
down on elevator this helps support the vertical throttle
shape
balsa block
1/16" PLY
BOTTOM
COWL FORMER RING
FORMER 1A
1/8" Balsa glue on doubler butt firwall to 1/32"
grain
1/4" PLY
FORMER 1
template
HOUSE OF BALSA
1/12 SCALE FW 190
CANOPY
former 3 1 deg.
grain location downthrust
grain 1/32" PLY FUSLAGE DOUBLER
1/16" BALSA
CRUTCH
1/8" X 1/8"
LONGERONS
FORMER 2A FORMER 1A This CAD plan is being offered as shareware. This DXF file
1/16" balsa crutch which is available @ www.scalecombat.com the official Radio
1/8" balsa 1/4" PLY Control Combat Association website may be given to anyone.
shape to this outline Do not alter this plan. Ues it and enjoy!! I encourgae you to
after buildup send $11.00 to register your CAD plans along with your name
1/8" balsa fuslage side
CUT AWAY AFTER and mailing address and Email address to:
ASSEMBLY TO ALLOW FOR
FORMER 1 ENGINGE CLEARANCE
SIG 4" COWL Steve Hergett
2814 Lewis Ave.
shape to this outline SECTION VIEW AT Billings, Mt. 59102
after buildup
1/16 crutch cut 1/4" PLY COWL FORMER
MAKE 2 RINGS. GLUE ONE TO
Printed full-size plans are available upon request from myself for
those who don't have the capabilities to use the CAD version of
SECTION VIEW SECTION VIEW
CUT 1/2" SEGMENT FROM
COWL FOR TIGHTER FIT TO the plans. Send $21.00 per set to the above address. You will
FUSLAGE. USE FIBERGLASS recieve your plans rolled in a tube postage paid USA.
TAPE AND EPOXY TO
REATTACH ENDS TOGETHER.
Specify: P-51 Mustang, TA 152 H or ME 109
FINISHED DIA. IS 3 3/4" 1/8" PLY sheet 1 of 2
3/16" dia. wing dowell hole
3/16" balsa
all ribs 1/16"
Firewall
C COPYRIGHT PROTECTED
ALL RIGHTS RESERVED
R1 R2 balsa 1999 STEVE HERGETT
shear sheet 2 of 2
web see page 1 for copy
R1 information
3/16" x 3/16"
balsa top and
vertical grain bottom spars
shearwebs R9
1/16" top, bottom along entire R8
& center section 1/16" x 1/4" length of wing
sheeting R7
1/64" ply capstrips on
top and
bottom of ribs R6
R5
1/16" R4
crossgrain R3
balsa
3/16" up & down 1 1/2" trailing edge stock
cut out aileron cut down to 1 1/4"
R2
after assembly
glue wedge to R1
balsa buildup
block torque rod
assembly
R8
R7 R9
R6
1/16" plywood
wing bolt R5
All ribs 1/16"
reinforcement on
balsa R4
bottom of wing sub rib
1/8" balsa wedge
R3
rear
dihedral
brace
R4
R5
R6
R7
R9 R8 R7 R6 R5 R4 R3
R8 R2 R1
R9