Professional Documents
Culture Documents
EXCAVATOR
(To be read in conjunction with preambles)
Excavation
A 007 Excavate to pits, small holes etc not exceeding 0.10m3 to No $ 6.00
receive base of posts, etc including removing surplus
excavated material off site and making good.
Filling
A 008 Supply dry approved earth filling obtained from outside m3 $ 10.50
source and fill in layers of 300mm including labour for
spreading, trimming and consolidating to form earth
moulds or levels.
SOR 1 / 131
Schedule of Rates
A 015 Supply and install minimum 1.5m high timber hoarding m $ 25.00
including painting as shown in drawing no: AMKTC-D1
A 016 Supply and install 2.4m high timber hoarding including m $ 37.50
painting as shown in drawing no. AMKTC-D1
A 017 Supply and install 2.4m high metal hoarding including m $ 48.50
painting as shown in drawing no. AMKTC-D1
A 019 Remove existing timber/metal hoarding and cart away off m2 $ 7.70
site.
A 021 Provide debris netting including framing, tie-backs and all m2 $ 2.30
necessary accessories (Access scaffolds exceeding 6m
height measured separately)
SOR 2 / 131
Schedule of Rates
CONCRETOR
(To be read in conjuction with preambles)
Concrete Work
B 007 Extra over Items 001 to 006 for trowelling concrete to m2 $ 0.60
footpath, apron etc.
B 009 Supply and cast concrete (Grade 20) in small quantities m3 $ 328.00
not exceeding 0.15 metre cube including all necessary
formwork
Reinforcement
B 010 Supply mild steel rod reinforcement fabricated and laid in kg $ 1.80
position including labour for forming stirrups, links, etc
irrespective of size.
SOR 3 / 131
Schedule of Rates
B 012 A5 m2 $ 4.75
B 013 A6 m2 $ 5.30
B 014 A7 m2 $ 6.90
B 015 A8 m2 $ 9.55
B 018 B6 m2 $ 8.30
B 019 B7 m2 $ 9.90
B 020 B8 m2 $ 11.75
B 022 D6 m2 $ 9.00
B 023 D7 m2 $ 12.90
B 024 D8 m2 $ 15.30
Formwork
B 030 Extra over timber formwork for curve surface work. m2 $ 3.50
SOR 4 / 131
Schedule of Rates
Drain/Water Channel
* Construct 230mm wide (internal) CONCRETE (Grade
25) SURFACE DRAIN with 100mm thick sides, 100mm
thick base reinforced with a layer of BRC No. B6
wiremesh. All exposed sides, base and arises rendered
smooth in cement mortar (1:3) including all necessary
excavation, hardcore, sand blinding and formwork, laid to
fall as directed for the following average depth to invert:
*(031-034)
B 035 Extra over items for precast concrete channel to 230mm m $ 3.40
wide reinforced concrete surface drain.
B 040 Extra Over for Precast Concrete channel to 300mm wide m $ 8.80
reinforced concrete surface drain.
B 041 Extra over for forming 50mm x 25mm rebate on both m $ 3.70
sides of channel for precast drain cover slab
(Measurement based on length of drain)
SOR 5 / 131
Schedule of Rates
B 044 Exceeding 300mm deep but not exceeding 450mm deep m $ 23.50
B 045 Exceeding 450mm deep but not exceeding 600mm deep m $ 33.40
SOR 6 / 131
Schedule of Rates
B 063 Construct scupper drain not exceeding 150mm wide and m $ 6.20
75mm deep on existing floor including trowelling surface
smooth.
SOR 7 / 131
Schedule of Rates
Precast Heelstones/Cills/Vents
B 070 Supply and lay 50mm thick reinforced precast concrete m2 $ 42.00
(Grade 25) paving slabs pointed in cement mortar
including BRC No. D6 reinforcement.
SOR 8 / 131
Schedule of Rates
B 080 Supply and lay 50mm thick grade 25 precast concrete No $ 21.50
slab 600mm x 300mm with top surface finished with
colour washed pebbles including excavation.
B 081 Supply and lay 50mm thick grade 25 precast concrete No $ 19.60
slab 600mm x 300mm with top surface finished with
granite stone including excavation.
B 082 Supply and lay 50mm thick grade 25 precast concrete No $ 26.70
slab 600mm x 600mm with top surface finished with
granite stone including excavation.
B 083 Labour for carefully taking out existing loose or sunken m2 $ 2.50
precast concrete slabs and stack aside for re-use.
B 084 Select from stack and re-use existing precast concrete m2 $ 4.60
slab for repairs including jointing in cement mortar 50mm
wide and levelling ground.
B 085 Extra over for pc slab laying on levelled sand bed of m2 $ 3.20
50mm thick
SOR 9 / 131
Schedule of Rates
Miscellaneous
B 093 Supply and plug up bin chute wall holes with 300mm No $ 18.80
diameter detachable precast concrete complete with
13mm diameter mild steel handle (exclude breaking
existing concrete wall)
B 097 To provide 150mm long PVC weep hole pipes not No $ 3.60
exceeding 50mm dia through brick/ concrete work not
exceeding 100mm thick.
SOR 10 / 131
Schedule of Rates
Footpath
Staircase
SOR 11 / 131
Schedule of Rates
BRICK/BLOCK WORKS
(To be read in conjunction with Preambles)
Brick/Hollow Block
C 003 Half brick thick reinforced with expanded metal brickwork m2 $ 31.80
reinforcement at every 4th course.
C 006 Half brick wall with facing bricks with expanded metal m2 $ 61.20
brickwork reinforcement at every 4th course laid in
prepacked mortar with 10mm joints raked 10mm deep
flush pointed in approved tinted cement mortar as work
proceeds.
C 011 190mm thick using M211 modular brick size 190 x 90 m2 $ 53.00
mm x 90mm.
C 012 90mm thick using M211 modular bricks size 190 x 90mm m2 $ 27.00
x 90mm reinforced with expanded metal brickwork
reinforcement at every four course.
C 013 90mm thick using M311 modular bricks size 290 x 90mm m2 $ 21.60
x 90mm reinforced with expanded metal brickwork
reinforcement at every fourth course.
C 014 Extra over common brickwork for forming exposed faces m2 $ 6.90
in selected common bricks, modular M211 & M311
including pointing in approved tinted cement mortar.
(Applicable to 002 to 004, 011 to 013)
C 015 Supply labour and materials to rake out mortar joints m2 $ 7.80
between standard bricks and repointing with prepacked
mortar (based on area of brickwall)
C 016 Supply labour and materials to rake out mortar joints m2 $ 6.50
between modular bricks and repointing with prepacked
mortar (based on area of brickwall)
C 033 Extra over half brickwall/solid block wall for the provision m $ 5.40
of hot dipped galvanised bonding bar system to the end
edges of brick wall/solid block wall
C 035 "NEG" or other approved glass block wall consists of 145 m2 $ 284.30
x 145 square glass block of 80 to 100mm thick glass laid
in prepacked mortar and pointed with approved tinted
cement mortar complete with panel reinforcing, panel
anchors, expansion strips, etc. according to
manufacturer's instructions.
C 038 Extra over item for filling the groove/ expansion joint solid m $ 1.40
with an approved backing rod.
C 039 Supply labour and materials to form splay with approved m $ 5.00
polymer modified cement mortor/non shrink grout to the
correct gradient including hacking when necessary.
C 042 Repair the patch joints between precast sills by mortar No $ 1.60
joint and approved polyurethane sealant according to
manufacturer's instructions.
Miscellaneous
C 047 Labour for raking out joints of existing brickwork, clean, m2 $ 5.90
re-jointing with cement mortar and re-pointing with a
flush joint.
C 049 Cutting out existing block or brick- work to form chase etc m $ 7.30
not exceeding 300mm girth.
C 052 Lay approved damp proof course well lapped at joints m2 $ 8.90
and bedded in prepacked mortar according to
manufacturer's instructions.
C 053 Supply and lay approved horizontal damp proof course m2 $ 8.90
complied with BS 6398 Type B (felt fibre base) to
brick/block walls bedded in prepacked mortar according
to manufacturer's instructions.
C 054 Hack out cracks of brick or block walls to form `V' shaped m $ 4.00
grooves approximately 25mm wide x 20mm deep and
seal up with polymer modified mortar and painting
surfaces to match existing.
C 059 Supply labour and materials to repair the plastered wall m2 $ 13.50
panels by applying two coats of approved prepacked
skim coat including hacking, painting to the repaired
surface.
C 063 Form nib with non shrink grout including Chemical m3 $ 3,835.10
Capsule at 300mm centre to centre, necessary
reinforcement, formwork, skimming coat and painting.
C 071 Supply and fix 100mm x 80mm x 6mm thick galvanised m $ 50.80
angle plate with approved 8mm diameter chemical
adhesive galvanised stud archor @ 150 c/c to existing
wall.
C 072 Supply labour and materials to rack out mortar joint at the m $ 4.20
interface to a depth of 25mm. Brush out all loose sand
and mortar and fill the groove with polymer modified
mortar.
C 075 Supply labour and materials to rake out existing mortar m $ 7.60
joint, brush out all loose materials, fill the joint with
approved backing rod, follow up with approved non-
shrink grout in accordance with the manufacturer's
instructions.
PAVIOR
(To be read in conjunction with preamble)
D 002 For every 5mm thick over (or under) 20mm m2 $ 1.40
SOR 19 / 131
Schedule of Rates
D 012 Extra over for using hardener or other approved non- m2 $ 1.50
metallic hardener mixed according to manufacturer's
instruction (applicable to other pavior items)
D 013 Extra over 3mm thick coloured cement topping finish of m2 $ 9.60
terracotta, white, red and green colour, surface floated
smooth with a steel trowel.
Granolithic Paving
D 019 20mm thick single coloured cement paving to floor laid in m2 $ 21.30
panels on and including minimum 10mm thick prepacked
base screed
Cast-in-situ terrazzo
SOR 20 / 131
Schedule of Rates
Mosaic Tiling
Brick Paving
D 031 Supply and lay new brick on edge in prepacked mortar to m2 $ 58.30
existing steps, coping, footpath, etc, including proper
surface preparation pointing with cement mortar.
SOR 21 / 131
Schedule of Rates
D 034 Brick on edge paving in double bullnose one brick width m $ 22.00
laid and bedded on and including 13mm thick prepacked
mortar
D 036 Brick tiles laid to approved pattern jointed, pointed and m2 $ 44.60
bedded on and including 13mm thick prepacked mortar
D 037 Supply and lay any size, minimum 8mm thick heavy duty m2 $ 56.60
homogeneous polished floor tile of approved colour and
pattern, jointed, pointed and bedded on and including
minimum 20mm thick prepacked screed.
* Supply and lay any size, minimum 8mm thk heavy duty
homogeneous polished floor tile of approved colour and
pattern, jointed & pointed with approved grout *(041-044)
D 042 Exceeding 0.1m2 but not exceeding 0.3m2 (for single No $ 19.00
patch)
SOR 22 / 131
Schedule of Rates
D 043 Exceeding 0.3m2 but not exceeding 0.5m2 (for single No $ 29.50
patch)
D 044 Exceeding 0.5m2 but not exceeding 1m2 (for single No $ 59.00
patch)
D 045 Supply and lay any size, minimum 8mm thick, heavy duty m2 $ 39.00
homogeneous unpolished floor tile of approved colour
and pattern, jointed, pointed and bedded on and including
minimum 20mm thick prepacked screed and pointing with
approved tile, grouts as specified.
* Supply and lay any size, minimum 8mm thk heavy duty
homogeneous unpolished floor tiles of approved colour
and pattern, jointed and pointed with approved grout (1:3)
*(049-052)
SOR 23 / 131
Schedule of Rates
D 057 Supply and lay nonslip nosing tile 200 x 60 x 8mm in m $ 13.10
steps or infront lift car entrance laid in approved colour,
jointed and pointed and bedded on and including
minimum 20mm thick prepacked base screed.
Slate Tiling
SOR 24 / 131
Schedule of Rates
D 074 Scrape off existing damaged parquet floor tile and m2 $ 5.10
remove all adhesive stains.
SOR 25 / 131
Schedule of Rates
D 081 Construct 100 x 200mm depth side kerb with grade 25 m $ 7.00
concrete including all necessary formwork.
D 084 Supply and lay imprint surface in any colour to floor with m2 $ 37.00
20mm thick cement and sand screed according to
manufacturer's instruction.
D 085 Supply and lay 20mm thick concrete paving to floor m2 $ 35.00
imprint with recessed pattern, approved colour and
varnish to match existing floor.
D 086 Supply and lay 50mm thick concrete stamping finish in m2 $ 40.00
patterns to floor according to manufacturer's instruction
(concrete base measured separately)
D 088 Supply and lay 15mm thick pebble wash finish to floor, m2 $ 34.50
laid in section.
D 089 Supply and lay border 100 to 150mm girth with pebble m $ 7.30
washed finish of 15mm thick.
D 090 Supply and lay border 150 to 300mm girth with pebble m $ 12.30
washed finish of 15mm thick.
D 091 Extra over for every 5mm thick for Item 088 to 090 m2 $ 8.30
Concrete Topping
SOR 26 / 131
Schedule of Rates
D 095 25mm thick exceeding 150mm but not exceeding 300mm m $ 9.60
in height/width
D 096 ADD to (or deduct from) Item 094 for each 5mm m $ 0.90
thickness over (or under) 25mm
D 097 ADD to (or deduct from) Item 095 for each 5mm m $ 1.25
thickness over (or under) 25mm
Vinyl Tiling
D 100 Supply and lay 2mm thick vinyl floor tile to match existing m2 $ 18.30
inclusive of approved adhesive (Removal measured
separately)
Self-levelling Screeding
D 102 Supply and lay 3mm thick acrylic polymer cementitious m2 $ 13.00
coating system c/w sealer coat to manufacturer's
specifications.
D 103 Add to Item 102 for one layer of coloured top coat to m2 $ 3.00
manufacturer's specifications.
D 104 Supply and lay self-levelling screed top coat (system B) to m2 $ 19.00
corridor and staircase landing.
SOR 27 / 131
Schedule of Rates
Dividing Strips
D 105 Mosaic tiles to form court line (38mm to 50mm wide) for m $ 4.70
badminton, sepak takraw and basketball courts, etc.
D 110 Supply and apply epoxy mortar screed flooring system m2 $ 41.00
with epoxy resin primer follow by a layer of minimum
5mm thick epoxy mortar and a non-slip sealer coat after
24 hours curing
D 111 Supply and lay one coat of finishing grout colour (sundek m2 $ 16.30
or other approved) to match existing complete with one
coat of acrylic clear top coat for repair to colour screed
surface.
Tactile Tile
D 113 Supply and lay "Tactile Tile" of approved design and m2 $ 96.40
colour, jointed, pointed and bedded on minimum 20mm
thick prepared base screed.
D 114 Supply and fix 135-145mm wide x 25mm thick culture m2 $ 350.00
deck plank / composite timber board including all
necessary fixing accessories
Artificial Turf
D 115 Supply and lay 40mm turf pile height artificial "Tiger Turf" m2 $ 58.00
SOR 28 / 131
Schedule of Rates
Miscellaneous
D 119 Hack existing floor to form random keys, clean and wash m2 $ 1.30
to receive new finish including removing debris from site.
D 121 Apply one coat of approved bonding agent to receive new m2 $ 0.80
finishings according to manufacturer's instruction
SOR 29 / 131
Schedule of Rates
D 129 Supply & lay “ Bond Flake” flooring to existing tiles m2 $ 30.00
surface according to manufacturer's instructions
D 130 Supply and apply epoxy sediment colour flakes coating m2 $ 41.00
system with 2-component epoxy resin binder follow by a
layer of sediment colour flakes and a non-slip 2-
component polyurethane binder. (Average thickness of
coating shall be 1.2mm)
SOR 30 / 131
Schedule of Rates
ROOFER
(To be read in conjunction with preambles)
E 001 Supply only unglazed clay roof tiles in all colour to match Piece $ 2.00
existing
E 002 Supply only semi-glazed clay roof tile in all colour to Piece $ 2.70
match existing
E 003 Supply only glazed clay roof tile in all colour to match Piece $ 4.00
existing
Concrete Panel
E 020 Lay over flat roof in 600 x 600 x 25mm thick panels in m2 $ 18.00
cement mortar 1:2 mixed with "sika" or other approved
water-proofing compound as per manufacturer's
instructions in the proportion of 2.3 kg of water-proofing
compound to 45 kg of cement and 10mm joints
subsequently filled with bitumen (Removal measured
separately)
Secondary Slab
Waterproofing
E 034 Supply and lay approved 1mm thick bitumen roofing felt m2 $ 7.60
as separation layer including bituminous paint for
temporary treatment to address roof leak (Taking out
existing and relay slabs measured separately)
E 039 Supply and lay fibre glass (FG 4) or other approved with m2 $ 2.10
minimum 100mm lapping (Fibre glass membrane is laid
between the 2 coats of Flinkote Ultra Waterproofing
Treatment)
E 042 Supply and apply 1 coat of "Newcoat" water based acrylic m2 $ 2.95
polymer waterproofing membrane with integral micro fibre
reinforcement (adhoc repair) (Removal of existing
waterproofing membrane measured separately)
Polycarbonate Sheet
Roof Insulation
E 049 Supply and lay 50mm rigid extruded polystyrene foam m2 $ 16.60
insulation board of density minimum 32 kg/m3
E 050 Supply and lay "Super Sisalation", "Super Brite" or other m2 $ 4.00
approved double-sided aluminium foil including lapping
with aluminium foil type
E 051 Supply and lay one layer of "Parsec Thermo Brite III" m2 $ 6.60
radient barrier to roof including lapping with thermosol-
brite tape
Expansion Joint
E 053 Rake out bitumen from normal expansion joints and refill m $ 4.30
same with approval bitumastic compound including base
packing.
End Thrust
E 054 Construct hot dipped galvanised steel angle end thrust No $ 39.80
support for existing pipe end to reinforced concrete flat
roof including all necessary fixing.
Metal Roof
E 055 Supply and fix Colourbond XRW "Kliplok 031" (22G) m2 $ 39.50
0.65mm thick or other approved steel roofing sheet to
existing steel purlin with bolts, nuts, washers sealing
washers, fixing brackets and other necessary accessories
E 056 Supply and fix colourbond steel "Kliplok 406" (G550) m2 $ 37.50
0.53mm thick or other approved steel roofing sheet to
existing steel purlins with approved proprietary clips, self
drilling clip fixing screw and necessary accessories
E 057 Supply and fix colourbond "Profiled" 0.63mm thick roofing m2 $ 39.70
sheet to steel purlins with bolts, nuts, washers, sealing
washers, fixing brackets and all necessary accessories
E 058 Supply and fix Colourbond XRW "Spandek" 0.47mm thick m2 $ 31.90
corrugated roofing sheets or other approved to existing
steel purlins including galvanised screws and all
necessary fixing accessories
E 059 Supply and fix "V" - (26G) 0.47mm thick crimp colourbond m2 $ 29.50
XRW Hi-Ten metal roofing sheet including all necessary
bends and fixing accessories
E 060 Supply and fix colourbond "Easyclad" 0.6mm thick (G300) m2 $ 38.40
cover width 300mm including approved proprietary clips,
screw and all necessary fixing accessories
E 063 Supply and fix single-sided 24G 0.56mm thick colourbond m2 $ 34.70
XRW flashings/cappings/ trims including bending flashing
as required and all necessary fixing accessories.
E 064 Rake out bitumen from 25mm wide expansion joints and m $ 24.20
refill same with approved hot- poured rubber bitumen
sealer including compressible non-extruded fibreboad
joint filler as base packing.
E 066 Repair to metal roof include refix metal roof sheet with all m2 $ 3.00
necessary fixing accessories
E 068 Add to (deduct from) item 067 to each 5mm thickness m2 $ 0.50
over (or under) 25mm
E 071 Add to (or deduct from) item 070 for each 5mm thickness m2 $ 1.50
over (or under) 20mm
E 074 Add to (or deduct from) item 072 for each m $ 1.00
5mm thickness over (or under)
20mm for 0-150mm girth
E 075 Add to (or deduct from) item 073 for each 5mm thickness m $ 1.45
over (or under)
20mm for 150-300mm girth
E 082 Repair damaged tensile membrane roofing (not more Spot $ 2,450.00
than 1m2) using heat weld or other approved methods by
specialist including material, equipment, removal of
debris and other related works
E 083 Extra over item 082 for additional spot not more than 1m2 Spot $ 1,000.00
at the same location
False Ceiling
F 005 Supply and fix 12mm thick soft board as ceiling or wall m2 $ 11.80
panel (timber framing and fillets measured separately)
F 006 Supply and fix 12mm thick mineral fibre or plasterglass m2 $ 25.60
ceiling boards in-fill including "L" shape aluminium
stiffener, where necessary
SOR 39 / 131
Schedule of Rates
F 012 Supply and fix "T" or "L" shaped galvanised steel strips m $ 4.00
with aluminium or enamel finishes not exceeding 30mm
wide as fillet for false ceilings/wall panels including
hanging wires or adjustable rod hanger.
F 013 Supply and fix 9mm thick egg crate plastic louvre for m2 $ 24.40
encasing gas pipe, etc.
Fire-Rated Doors
F 014 Supply and install 45mm thick single leaf half-hour fire m2 $ 355.00
rated timber door complying with SS332 complete with
fire proofed lockset, hinges, flush bolt, door closer
necessary ironmongeries and frame
F 015 Supply and install 45mm thick double leaves half-hour fire m2 $ 420.00
rated timber door complying with SS332 complete with
fire proofed lockset, hinges, flush bolt, door closer,
necessary ironmongeries and frame
F 016 Supply and install 45mm thick single leaf half-hour fire m2 $ 375.00
rated timber door with wired clear vision panel size of
150x300mm height with backing piece, sealants, “C”
channels complying with SS332 complete with fire
proofed lockset, hinges, flush bolt, door closer, necessary
ironmongeries and frame
F 017 Supply and install 45mm thick double leaves half-hour fire m2 $ 440.00
rated timber door with wired clear vision panel size of
150x300mm height with backing piece, sealants, “C”
hannels complying with SS332 complete with fire proofed
lockset, hinges, flush bolt, door closer, necessary
ironmongeries and frame
F 018 Supply and install 45mm thick single leaf half-hour fire m2 $ 390.00
rated aluminium clad timber door complying with SS332
complete with fire proofed lockset, hinges, flush bolt, door
closer, necessary ironmongeries and frame
F 019 Supply and install 45mm thick double leaves half-hour fire m2 $ 460.00
rated aluminium clad timber door complying with SS332
complete with fire proofed lockset, hinges, flush bolt, door
closer, necessary ironmongeries and frame
F 020 Supply and install 45mm thick single leaf one-hour fire m2 $ 450.00
rated timber door complying with SS332 complete with
fire proofed lockset, hinges, flush bolt, door closer,
necessary ironmongeries and frame
SOR 40 / 131
Schedule of Rates
F 021 Supply and install 45mm thick double leaves one-hour m2 $ 530.00
fire rated timber door complying with SS332 complete
with fire proofed lockset, hinges, flush bolt, door closer,
necessary ironmongeries and frame
F 022 Supply and install 45mm thick single leaf one-hour fire m2 $ 470.00
rated timber door with wired clear vision panel size of
150x300mm height with backing piece, sealants, “C”
channels complying with SS332 complete with fire
proofed lockset, hinges, flush bolt, door closer, necessary
ironmongeries and frame
F 023 Supply and install 45mm thick double leaves one-hour m2 $ 550.00
fire rated timber door with wired clear vision panel size of
150x300mm height with backing piece, sealants, “C”
channels complying with SS332 complete with fire
proofed lockset, hinges, flush bolt, door closer, necessary
ironmongeries and frame
F 024 Supply and install 45mm thick single leaf one-hour fire m2 $ 485.00
rated aluminium clad timber door complying with SS332
complete with fire proofed lockset, hinges, flush bolt, door
closer, necessary ironmongeries and frame
F 025 Supply and install 45mm thick double leaves one-hour m2 $ 570.00
fire rated aluminium clad timber door complying with
SS332 complete with fire proofed lockset, hinges, flush
bolt, door closer, necessary ironmongeries and frame
Timber Door
F 026 Supply and install 38mm thick Framed, Ledged and m2 $ 92.00
Braced Door filled in with 19mm thick tongued and
grooved timber boarding with „V” joint as shown in
drawing no. AMKTC-D17
F 027 Supply and install 45mm thick Framed, Ledged and m2 $ 101.20
Braced Door filled in with 22mm thick tongued and
grooved timber boarding with „V” joint
F 028 Supply and install 50mm thick Framed, Ledged and m2 $ 112.70
Braced Door filled in with 25mm thick tongued and
grooved timber boarding with „V” joint
SOR 41 / 131
Schedule of Rates
F 029 Supply and install 38mm thick timber louvred door with m2 $ 108.10
framing slot, fix and filled with timber louvers at an angle
of 60 degrees not more than 40mm apart including fixing
fillets.
F 030 Supply and install 45mm thick timber louvred door with m2 $ 118.50
framing slot, fix and filled with timber louvers at an angle
of 60 degrees not more than 40mm apart including fixing
fillets.
F 031 Supply and install 38mm thick solid core flush door m2 $ 115.00
comprising of hardwood lipping all round core strips glued
and well cramped together and covered on both sides
with 6mm thick plywood.
F 032 Supply and install 45mm thick solid core flush door m2 $ 124.20
comprising of hardwood lipping all round core strips glued
and well cramped together and covered on both sides
with 6mm thick plywood.
F 033 Supply and install 38mm thick semi-solid flush door m2 $ 101.20
comprising of hardwood lipping all round stiles and rails
covered on both sides with 6mm thick plywood
F 034 Supply and install 45mm thick semi-solid flush door m2 $ 109.30
comprising of hardwood lipping all round stiles and rails
covered on both sides with 6mm thick plywood
F 035 Supply and install 38mm thick hollow flush door m2 $ 86.30
comprising of skeleton framing, hardwood lipping all
round and covered on both sides with 6mm thick plywood
F 036 Supply and install 45mm thick hollow flush door m2 $ 94.30
comprising of skeleton framing, hardwood lipping all
round and covered on both sides with 6mm thick plywood
F 038 Supply and install 38mm thick panel door in 4 panels with m2 $ 80.50
9.5mm thickness plywood with rebated and mounded
rails & stiles framed around timber panels
SOR 42 / 131
Schedule of Rates
F 039 Supply and install 45mm thick panel door in 4 panels with m2 $ 87.40
9.5mm thickness plywood with rebated and mounded
rails & stiles framed around timber panels
F 040 Supply and install 50mm thick panel door in 4 panels with m2 $ 94.40
9.5mm thickness plywood with rebated and mounded
rails & stiles framed around timber panels
F 041 Supply and install 19mm thick framed cupboard door m2 $ 36.30
covered on both sides with 6mm thick plywood
F 042 Supply and install 25mm thick framed cupboard door m2 $ 41.80
covered on both sides with 6mm thick plywood
F 043 Supply and install 32mm thick framed cupboard door m2 $ 44.00
covered on both sides with 6mm thick plywood
F 044 Take down part decayed timber doors take out decayed m2 $ 17.40
members and incorporate new members, adjust and re-
assemble door including all necessary dowels and
wedges and re-fixing doors to position (new timber
members measured separately)
F 045 Take down warped doors, ease, adjust and refix to m2 $ 4.30
position
F 046 Cut into/take out part (not whole piece of timber member), m $ 8.00
rotten or decayed frames, mullion, transome, cills,
handrails, etc and form all necessary approved joints to
receive new timber including taking down of doors, if
necessary and rehanging in position new timber
measured separately)
F 047 Bore holes to door panels not exceeding 25mm diameter No $ 0.60
for ventilation
F 048 Pull off existing nails, hooks, screws etc. from timber and No $ 0.40
fill up holes with wood putty or other approved material
and touch up with paint to match existing
F 049 Fill up door lock holes, hinge rebates, etc with and No $ 2.70
including adhesive and timber, sand-papering and
knotting, and painting to match existing
SOR 43 / 131
Schedule of Rates
WINDOWS
F 051 Supply and fix vinyl gester sealing strips to perimeter of m $ 2.10
window frame with holding down screws or nails at 60mm
centre
F 052 Supply and install 38mm thick windows with framings m2 $ 75.00
stop slotted and filled in with 13mm thick timber louvres
including fixing fillets
F 053 Supply and install 38mm thick framed windows open m2 $ 56.10
rebated and prepared for glass including fixing beadings
(glass measured separately)
F 054 Take down part decayed timber windows take out m2 $ 17.00
decayed members and incorporate new members, adjust
and re-assemble windows including all necessary dowels
and wedges and re-fixing windows to position (New
timber members measured separately)
F 055 Take down warped windows, ease, adjust and refix to m2 $ 7.60
position
F 056 Cut into/take out part (not whole piece of timber member), m $ 8.00
rotten or decayed frames, mullion, transome, cills,
handrails, etc and form all necessary approved joints to
receive new timber including taking down of windows, if
necessary and rehanging in position (New timber
measured separately)
F 057 Supply and fix rubber glazing gasket to Notice Board, m $ 3.80
sliding windows, top hung and casement windows
Table Tops
F 058 Refix loose or fallen table top including all necessary No $ 11.70
drilling, pop-rivetting and welding
F 059 Supply and fix 1000mm diameter 25mm thick "Werzalit" No $ 156.40
or other approved table tops to match the existing
inclusive plastic numbering (if any) to new table properly
installed with fixing rivets
F 060 Supply and fix 900mm dia x 17mm thick with edge profile No $ 149.50
of 25mm thick "SM France" table top or other approved to
match the existing inclusive plastic numbers (if any) to
new table properly installed with fixing rivets
SOR 44 / 131
Schedule of Rates
F 061 Supply and fix 1050mm dia x 17mm thick with edge No $ 172.50
profile of 35mm thick "SM France" table top or other
approved to match the existing inclusive plastic
numbering (if any) to new table properly installed with
fixing rivets
F 062 Supply and fix 1070mm dia x 12mm thick with edge No $ 210.00
profile of 25mm thick solid surface table top with plywood
backing or other approved to match existing inclusive of
transferring existing plastic numbering (if any) to the new
table properly installed with fixing rivets
F 063 Supply and fix 1200mm dia x 12mm thick with edge No $ 256.75
profile of 25mm solid surface table top with plywood
backing or other approved to match existing inclusive of
transfering existing plastic table numbering (if any) to the
new table properly installed with fixing rivets
F 072 Supply and fix plastic/acrylic numbering to table top with No $ 2.50
fixing rivets (per no. means per plate)
Stools
F 073 Refix loose or fallen stool top including all necessary No $ 9.30
drilling, pop-rivetting and welding.
F 074 Supply and fix 300mm dia 12mm thick solid surface thick No $ 37.95
stool top without plywood backing only to match the
existing.
SOR 45 / 131
Schedule of Rates
F 075 Supply and fix 340mm dia 12mm thick solid surface stool No $ 40.25
top with plywood backing to match existing.
F 076 Supply and fix 300mm diameter x 19mm thick high No $ 66.00
pressure compact laminate stool top properly installed
with fixing rivets.
F 077 Supply and fix 850mm x 350mm x 19mm thick peanut No $ 246.00
shape high pressure laminate stool top properly installed
with fixing rivets
F 078 * Supply and fix 400mm x 350mm x 12mm thick odd No $ 122.00
shape high pressure laminate stool top properly installed
with fixing rivets
SOR 46 / 131
Schedule of Rates
F 098 Supply and fix heavy duty galvanised hasp and staple for No $ 9.50
roof trap door
F 099 Supply and fix 50mm long aluminium or galvanised steel No $ 1.50
hasp and staple
F 100 Supply and fix 75mm long aluminium or galvanised steel No $ 1.70
hasp and staple
F 101 Supply and fix 150mm long galvanised steel hasp and No $ 4.80
staple
Locking Eye/Ear
F 103 Supply and fix 100mm x 60mm x 3mm stainless steel No $ 8.80
plate as locking ear to switch room, pump room etc.
Door Holder/Closer
F 106 Supply and fix 38mm diameter rubber door stop No $ 1.40
F 107 Supply and fix of "Yale" Model lite 2 or other approved No $ 33.70
auto-retractable hydraulic door closer including refixing,
adjusting to position
SOR 47 / 131
Schedule of Rates
Keys
F 110 Supply and cut one key to lock with missing keys No $ 9.70
including taking out lock, where necessary and refix same
F 111 Open door to gain access into premises where keys have Flat $ 7.40
been lost
F 112 Provide locksmith for gaining access to premises without Flat $ 50.00
damaging the lock
Door Handles
F 113 Supply and fix approved stainless steel cup handle for No $ 12.90
pumproom, switchroom, service duct door, etc.
F 114 Supply and fix approved stainless steel cup handle No $ 34.80
passage latch for service duct door with cup handles on
both sides
Anchors
SOR 48 / 131
Schedule of Rates
SOR 49 / 131
Schedule of Rates
SOR 50 / 131
Schedule of Rates
SOR 51 / 131
Schedule of Rates
F 184 Supply and fix eye-anchor including epoxy putty and No $ 6.30
approved nylon plug but exclude drilling of holes
F 185 Supply and fix brass roller to roof access door No $ 16.10
F 186 Supply and fix steel roller to roof access door No $ 7.50
F 187 Supply and fix metal rails to roof access door No $ 40.00
Padlocks
SOR 52 / 131
Schedule of Rates
F 210 Supply 300mm long chain/ring fixed to metal box, door No $ 2.70
etc for padlock
Security Padlocks
SOR 53 / 131
Schedule of Rates
Locksets
F 218 Supply and fix cam lock (Yale Model No. 490.3) for letter No $ 19.30
box or other uses including spot weld the locking nut,
where necessary
F 219 Supply and fix approved master lock to door behind letter No $ 20.40
boxes
F 220 Supply and fix in replacement central control lock system No $ 220.00
at letter box compartment complete with 1 no of key
F 222 Supply and fix lock for notice board in master key alike No $ 30.00
system
F 223 Supply and fix "Yale" 513/32626 single cylinder mortice No $ 87.00
dead lock
F 224 Supply and fix cylinder rim drawback locks ("Union" 1332- No $ 55.00
SE, "Yale" No. 1 or other approved) complete with 3 keys
F 225 Supply and fix cylinder mortice lockset complete with No $ 71.30
stainless steel handle ("Union" 643/46/41, "Showa" CL-05-
240 or other approved)
F 226 Supply and fix cylinder mortice lockset complete with No $ 75.00
stainless steel handle and 3 nos key for key alike system
F 227 Supply and fix double cylinder mortice lockset with No $ 77.70
stainless steel handle ("Union" 643/46/241, "Showa" CL-
26-240 or other approved)
F 230 Supply and fix single cylinder mortice lock "Union" 2441, No $ 83.50
"Yale" 514/32626 or other approved to aluminium sliding
door
SOR 54 / 131
Schedule of Rates
F 231 Supply and fix single cylinder mortice lock with thumbturn No $ 90.60
and lever handle on both sides
"Accord 0706P2 (6072) 1405-SS-65 & 1591-SIS"
F 233 Supply and fix "Union" 8098 or other approved indicating No $ 15.00
bolt for toilet door
F 235 Forte H6RP75ES under HDB master key series MK48 No $ 67.80
F 237 Yale 3203A/214.62 under MKAA and master key series No $ 81.60
MK48
F 240 Automatic locking rim lock with "TMR Series" key No $ 100.00
F 241 Supply and install door closing handle for toilet cubicle No $ 80.00
door.
F 242 Take out locks, repair, oil and ease lock and refix to No $ 7.40
position.
Sawn Timber
F 243 Supply and fix Sawn Kapoh Balau or Keruing in wall m3 $ 1,588.00
plates, rafters, purlins, or joists, collars, etc. including
tanalising or two coats wood preservative.
SOR 55 / 131
Schedule of Rates
Wrot Timber
F 251 Moulded architraves, cover fillets, etc not exceeding 500 m $ 1.50
sq mm in sectional area
Plywood Panels
SOR 56 / 131
Schedule of Rates
Rubber Guard
F 265 Supply and fix 150mm x 30mm thick rubber protection m $ 51.80
guard with 2 nos. HRD-N fastener screws at 500mm
centre to centre to walls of dustbin compound
Locking Bar
F 266 250mm long weld to 38mm x 100mm x 5mm thick flat No $ 8.90
handle
F 267 300mm long weld to 38mm x 100mm x 5mm thick flat No $ 9.30
handle
F 268 360mm long weld to 75mm x 100mm x 5mm thick flat No $ 9.90
handle
F 269 460mm long weld to 75mm x 100mm x 5mm thick flat No $ 10.40
handle
F 270 Supply and fix 13mm long stainless steel sike sharpen No $ 2.70
from 3.2mm diameter rod complete with 35mm x 15mm x
3mm base plate including all necessary fixing
accessories.
Ball Catch
F 271 Supply and fix 60mm brass or satin nickel double ball No $ 8.20
catch to door, etc
F 272 Supply and fix 2 pairs of 60mm brass or satin nickel Door $ 17.60
double ball catch to service duct door including removing
existing night latch lockset, patching, painting and making
good affected area.
SOR 57 / 131
Schedule of Rates
F 273 Supply and fix 6mm thick waterproof plywood Type WBP Per $ 94.50
as air-con opening panel including wrot balau/kapor Job
timber frame, seal up joint with approved sealing
compound, painting to match and make good all works
disturbed (overall size not exceeding 0.63m2 (Gondola
shall be paid separately)
F 274 Supply and fix 2mm thick aluminium sheet as air-con Per $ 141.50
opening panel including 100 x 25 x 1.2mm natural Job
anodised aluminium frame, seal up joint with approved
sealing compound, painting to match and make good all
works disturbed (over size not exceeding 0.63m2)
(Gondola shall be paid separately)
Miscellaneous
F 275 Take out serviceable hinges, locks, bolts etc and refix to No $ 2.00
new doors/ windows etc.
F 276 Supply and fix pop rivets to aluminium louvre blade or No $ 0.40
other aluminium fittings
F 277 Supply and fix "Hilti" or other approved raw plug including No $ 2.40
use of gun and explosive charges
F 278 Refix wall mounted bin including all necessary drilling, No $ 3.70
fixing screws, rivet, bolts, nuts, etc.
F 279 Supply and fix 3mm thick galvanised mild steel No $ 23.20
chequered plate cover for CRC compactor room locking
device including 100mm pressed steel butt hinges,
locking eye and all necessary fixing accessories (overall
size not exceeding 0.15m3)
F 281 Supply and fix in replacement approved flush bolt latch No $ 50.00
including all fixing accessories etc.
SOR 58 / 131
Schedule of Rates
F 283 Supply and fix 13mm x 5mm x 13mm aluminium "U" No $ 26.30
channel framing fix to lift car panel by pop riveting.
F 284 Supply and install clear transparent acrylic lift certificate No $ 13.00
holder
SOR 59 / 131
Schedule of Rates
Gutters
G 009 Supply and fix stainless steel mesh, roof gutter including m2 $ 16.50
dressing over gutter sides and fixing with rust-resistant
nails.
G 010 Spot solder or re-bolt joints of zinc sheet gutter including Joint $ 1.70
touch up with approved water proof roofing compound
internally and 1 primer coat and a finishing coat of
enamel paint externally.
SOR 60 / 131
Schedule of Rates
Rainwater Downpipe
Gratings
G 014 Supply and fix hot-dipped galvanised steel drain cover m2 $ 170.30
grating for concealed drain, hinged on one side and
overall 35mm thick fabricated with 25mm x 5mm
intermediate flats spaced at 25mm centres resting on
10mm diameter cross bar and support on 63mm x 38mm
x 4.5mm angle galvanised frame anchored to structure
with fish tail complete with locking bar.
SOR 61 / 131
Schedule of Rates
G 021 Supply and fix galvanised steel wire balloon grating to top No $ 4.10
of 75mm to 150mm vent pipes including spring clips and
1 coat of bituminous paint.
SOR 62 / 131
Schedule of Rates
SOR 63 / 131
Schedule of Rates
G 050 Supply and fix 600 - 750mm dia 32 stainlesss steel pc $ 250.00
folding grab bar complete with stainless steel mounting
cap and necessary fixing accessories
G 051 Supply and fix 500 - 600mm dia 32 stainless steel angled pc $ 120.00
grab bar complete with stainless steel mounting cap and
necessary fixing accessories
G 052 Supply and fix 1000 - 1200mm dia 32 stainless steel pc $ 180.00
angled grab bar complete with stainless steel mounting
cap and necessory fixing accessories
G 053 Supply and fix dia 32 stainless steel wall mounted grab m $ 100.00
bar complete with stainless steel mounting cap and
necessory fixing accessories
G 054 Supply and fix dia 35 mm stainless steel nylon wall m $ 160.00
mounted grab bar complete with stainless steel nylon
mounting cap and necessory fixing accessories
G 055 Stainless steel flats, angles, plates, channels, bolts, etc. kg $ 26.10
including cutting, welding, polishing, bending and fixing
on site complete with other fixing accessories
G 056 Supply and install aluminium low jail bar barrier in powder m $ 195.00
coated or anodised finish including excavation, concrete
foundation and disposal of excavated materials off site.
(Drawing no.AMKTC-D26)
G 057 Supply and install aluminium low jail bar barrier in powder m $ 230.00
coated or anodised finish including aluminium cast base
with anchorage bolts.
(Drawing no. AMKTC-D26)
G 058 Supply and install aluminium Double Row Guard Rail in m $ 130.00
powder coated or anodised finish including excavation,
concrete foundation and disposal of excavated materials
off site.
(Drawing no. AMKTC-D27)
G 059 Supply and install aluminium Double Row Guard Rail in m $ 163.00
powder coated or anodised finish including aluminium
cast base with anchorage bolts.
(Drawing no. AMKTC-D27)
G 060 Extra over for additional horizontal row to Double Row m $ 23.00
Guard Rail.
SOR 64 / 131
Schedule of Rates
Welding
G 062 Continuous fillet weld for welding loose, corroded or new m $ 17.20
steel work including the provision of welding rods, plant
etc filing smooth, repainting to match existing and the
cutting and removal of corroded parts, if any. (New steel
work measured separately).
G 064 Continuous fillet weld for welding loose or new stainless m $ 21.60
steel members including the provision of stainless steel
welding rods/wires, brazing/welding plants etc and filing
smooth and polishing (stainless steel measured
separately)
Bin/Refuse Chute
G 067 Supply and fix anodised aluminium refuse chute door No $ 162.30
including 100mm long stainless steel butt hinges,
purpose-made steel padbolt.
G 069 Supply and fix 100mm aluminium alloy butt hinge to No $ 4.70
refuse chute door including pop-riveting.
G 070 Supply and fix 130mm heavy duty galvanised butt hinges No $ 4.70
to refuse chute door including all necessary insulating felt
and additional aluminium plate backing, where
necessary.
G 071 Supply and fix rubber lining to refuse chute doors/frames. m $ 1.90
G 072 Supply and fix 6mm thick stainless steel latch with 3mm No $ 9.20
thk stainless steel backing plate to bin chute door
including all necessary drilling, fixing, screws, bolts, nut,
etc.
SOR 65 / 131
Schedule of Rates
G 073 Supply and fix 9mm thick aluminium bolt staple to bin No $ 5.00
chute door including all necessary drilling, fixing screws,
etc.
G 075 Supply and fix 40mm thick inspection cover for refuse No $ 541.20
chute overall size 1140 x 1140mm to top of refuse chute
comprising of 1.2mm thick anodised aluminium alloy
sheets on both faces supported with 1.2mm thick
galvanised "C" channel bracings and infilled with
rockwool insulation complete with 5mm thick extruded
aluminium section framings including stainless steel
friction stay, hinges, etc to manufacturer's detail.
G 076 Break through refuse chute wall for purpose of renewal of 1 Opg $ 35.30
refuse chute pipes etc and make good wall to match
existing and touch up with 2 coats of emulsion paint.
G 077 Clear choke in refuse chute and cart away to contractor's Storey $ 14.50
own dumping ground.
Flashing
SOR 66 / 131
Schedule of Rates
Expansion Joints
G 087 Exceeding 200mm girth but not exceeding 300mm girth m $ 17.60
Letterboxes
G 089 Supply and fix anodised aluminium letter box flap No $ 24.40
complete with engraving of house number to match
existing (Non Anti-Junk Mail Type)
SOR 67 / 131
Schedule of Rates
G 094 Supply and install 28mm width x 1mm thick anodised with No $ 3.40
natural colour, aluminium number plate to letter box with
engraving of house number 12mm height including pop-
rivetting and remove existing damaged plate, complying
to Singapore Post requirements.
G 096 Supply and install 330mm x 900mm height stainless steel No $ 218.00
junk mail door and frame with engraved sign (Junk Mail)
on door.
Fencing
G 103 Extra over 098 to 102 for infilling the mesh with one way m2 $ 15.10
interlocking aluminium slat to direction as directed by the
SO, including two coats of enamel paint to both sides of
angle iron post as directed.
SOR 68 / 131
Schedule of Rates
G 104 Extra over 098 to 102 for infilling the mesh with double m2 $ 21.50
way interlocking aluminium slat to direction as directed by
the SO, including two coats of enamel paint to both sides
of angle iron post as directed.
G 105 Extra over 098 to 102 for 3 rows of barbed wires and m $ 1.80
including additional 300mm height of mild steel angle
post at 3m centre straight on top bent to form spurs.
G 106 Galvanised barbed wire fixed with and including staples m $ 0.30
etc.
G 109 Repair fallen chain link fencing not exceeding 2.5m high m $ 4.40
including supplying all necessary extra straining tying
wires, split pins forming new concrete base etc.
G 110 Resite existing chain link fencing not exceeding 2.5m high m $ 9.10
including supplying all necessary extra straining tying
wires, split pinns forming new concrete base etc.
G 111 Replace existing PVC coated chain link fencing not m2 $ 22.50
exceeding 2.5m high including all necessary extra
straining tying wire.
G 112 Supply and fix 2.40 metre height ww 3060 galvanised m2 $ 126.00
maxi mesh or other approved fencing (min. 8.5 kg/m2),
framed with 25 x 25 x 2.3mm thick galvanised hollow
section and galvanised steel flat plate of 25 x 3mm thick;
constructed with 75 x 75 x 3mm thick galvanised steel
hollow section post at 2.6 metre centres and bedded in
450 x 450 x 600mm deep concrete (1:2:4) foundation
including 50 x 50 x 4mm thick galvanised flat plate
welded between hollow section post and maxi mesh
frame all as specified in details drawing no. AMKTC-D31
SOR 69 / 131
Schedule of Rates
G 115 Supply only BRC hot-dip galvanised weld mesh 50 x 150 m2 $ 33.20
x 5mm dia for fencing.
G 116 Supply and install BRC hot-dipped galvanised weld mesh m2 $ 44.60
50 x 150 x 5mm diameter for fencing.
G 117 Supply and install 2m high ball rebound fence of 75mm x m $ 300.00
12.5mm welded mesh having a wire gauge of 4mm (with
PVC coating) complete with 50 x 50 x 3mm thick hot
dipped galvanised vertical posts spaced at maximum
2.4mm intervals and embedded in 300 x 300 x 700mm
deep concrete base (1:2:4), 3 nos. 50 x 25 x 3mm thick
hot dipped galvanised horizontal rails (top, middle and
bottom). The horizontal rails shall be welded to the
vertical posts. All posts and rails are to be finished with
one coat of primer and two coats of enamel paint. The
welded mesh shall be electrically welded at every
intersection, powder coated and galvanised. The welded
mesh shall be sandwiched in between the vertical posts
and galvanised flat bar of size 38 x 4.5mm and secured
with M6 x 40mm long self- driving screws complete with
hexagonal washer and rubber stopper.
SOR 70 / 131
Schedule of Rates
SOR 71 / 131
Schedule of Rates
G 120 Extra over for Items 117 to 119 for endorsement and Per Job $ 500.00
submission of drawings to the relevant Authorities for
approval by Qualified Person/Professional Engineer
including site supervision when required.
Doors
G 122 Supply and fix mild steel hook for aluminium wc bathroom No $ 5.70
door hinge.
G 123 Supply and fix mild steel strap hinge including pop- No $ 4.00
rivetting to W.C./bathroom door.
G 124 Supply and fix aluminium strap hinge including pop- No $ 4.30
rivetting to W.C./bathroom door.
G 125 Supply and fix approved aluminium strap locking bars of No $ 6.10
sizes 75mm to 200mm long to hawker stalls aluminium
door including additional aluminium plate backing and
pop-riveting.
G 126 Supply and fix 50mm thick access trap door to RC roof No $ 449.20
overall size 1150 x 1150mm comprising 1.2mm thick
anodised aluminium alloy sheets on both faces supported
with 38 x 20 x 1.2mm thick galvanised steel "C" channel
bracings and 60 x 38 x 1.2mm thick galvanised steel "C"
channel framings infilled with rockwool insulation
including approved hasp and staple, brass rollers to
manufacturer's details in drawings no. AMKTC-D18,
AMKTC-D19, AMKTC-D20.
G 127 Supply and fix plastic roller to roof access door. No $ 11.70
SOR 72 / 131
Schedule of Rates
G 130 Supply and fix mild steel Sliding and Folding Door m2 $ 171.70
including all necessary fixtures, accessories and 1
priming coat and 2 finishing coats of enamel paint to
match existing.
G 135 Supply and fix aluminium fixed full louvred door complete m2 $ 257.60
with 2.3mm thick extruded aluminium louvred blades
including all necessary fixing accessories (Door frame,
lockset, door closer to be paid separately) (AMKTC-D24)
G 136 Supply and fix mild steel door frame including fishtail m $ 31.80
holdfast.
G 137 Supply and fix anodised aluminium half louvred and half m2 $ 283.30
panel door including stainless steel or brass butt hinges
and all necessary ironmongery (Door frame, lockset, door
closer to be paid separately)
G 138 Supply and fix 100 x 25 x 2.3mm thk aluminium door m $ 32.80
frame with 13mm wide inner stopper frame including
plastering and painting (exclude Hinges)
SOR 73 / 131
Schedule of Rates
G 139 Supply and install approved pvc door not exceeding No $ 102.70
1.70m2 complete with brass hook & eye and all
necessary fixtures.
Gates
G 144 Supply and fix standard metal collapsible gates from m2 $ 127.40
approved manufacturers including all necessary fixing
lugs, guide rails, rollers and gate locks. Prime and paint
with 2 coats of aluminium paint
G 145 Supply and install single or double leaf gate consisting of m2 $ 126.10
50mm diameter galvanised steel tubular framing filled in
with 50 x 50mm weldmesh, 75mm diameter galvanised
iron tubular gate posts with bottom end encased in 450 x
450 x 600mm concrete (1:2:4) foundation, the gates hung
on 2 pairs approved hooks and ride hinges and fitted with
approved locking bolt including all necessary welding and
painting (Net area of leaf measured).
G 146 Supply and install mild steel grille gate (in accordance Set $ 246.40
with HDB's standard drawings) fixed to metal gate frame,
metal door frame or timber door frame (frame measured
separately) with and including one primer coat (red lead
primer or zinc chromate primer) and approved mortice
lock (but excluding hinges) of any HDB's standard flower
patterns and sizes not exceeding 940mm width x
2140mm height.
SOR 74 / 131
Schedule of Rates
Windows
G 147 Supply and fix Safety Catch/sash lock for aluminium No $ 2.10
sliding window.
G 150 Supply and fix adjustable louvred window with single Set $ 9.70
control side frames for 8 Nos. 150mm wide glass or metal
louvres in height including rattleproof spring clips and all
necessary bolts and nuts and fixed to wood, concrete or
brick etc. (Louvres measured separately.)
G 151 Supply and fix adjustable louvred windows with dual Set $ 12.20
control side frames for 8 nos. 150mm wide glass or metal
louvres in height including rattleproof spring clips and all
necessary bolts and nuts and fixed to wood or brickwork
etc. (Louvres measured separately).
G 152 Supply and fix burglar proof type adjustable louvred Set $ 12.80
window with single control side frames for 8 nos. 150mm
wide glass or metal louvres in height including rattleproof
spring clips and all necessary bolt & nuts and fixed to
wood concrete or brick etc (Burglar proof bars and
louvres measured separately).
G 153 Supply and fix burglar proof type adjustable louvred Set $ 15.10
windows with dual control side frames for 8 nos. 150mm
wide glass or metal louvres in height including rattleproof
spring clips and all necessary bolts and nutts and fixed to
wood or brickwork etc but burglar proof type (Burglar
proof bars measured separately)
SOR 75 / 131
Schedule of Rates
G 154 Supply and fix 10mm square mild steel burglar proof bars m $ 3.20
with rustproof finish to brackets of adjustable louvred
frame.
G 155 Cost adjustment for each lourve add to (or deduct from No $ 1.60
items 150 to 153)
G 156 Extra over for forming mullions for adjustable louvred No $ 2.80
window of any height including spacers, bolts, nuts and
screws.
G 157 Supply and fix 1.588mm thk extruded aluminium lourved No $ 5.90
blades size not execeeding 600mm x 150mm wide in
anodised finish to adjustable louvre windows including
pop rivets.
G 158 Take down glass or metal louvres from adjustable louvre Set $ 3.50
windows not exceeding 12 louvres in height and stack
aside for re-use, dismantle existing damaged louvre
frame from wall, timber frame and cart away debris.
G 159 Service and repair adjustable louvre window frame Set $ 3.20
including the use of all necessary additional spare parts,
easing of windows, refixing same to wall or timber frame
(fixing of louvre blades measured separately).
Ceiling
G 163 Supply and fix 600 x 600 x 0.5mm thk Trinet or other m2 $ 60.00
approved perforated false ceiling complete with standard
fixing accessories
SOR 76 / 131
Schedule of Rates
G 166 Supply and fix Luxalon or other approved 0.5mm thick m2 $ 63.60
perforated metal ceiling including framing and fillets
G 167 Supply and install Luxalon or other approved 0.5mm thick m2 $ 77.60
perforated aluminium ceiling including framing and fillets
G 168 Supply and install 10mm thick GE Lexan thermoclear twin m2 $ 141.40
walled solar control venetian polycarbonate sheet in
standard tint complete with DS "168" black anodised
aluminium clamping bar system and including fixing
accessories
Bicycle Racks
G 169 Remove and cart away existing disused bicycle stands No $ 1.80
including painting where necessary
G 170 Refix existing bicycle stands with ramset fixings including No $ 4.80
paint surfaces to match existing at orginal position
G 171 Refix existing bicycle stands with ramset fixings including No $ 5.50
paint surfaces to match existing at new position.
SOR 77 / 131
Schedule of Rates
G 177 Supply and install new double tier bicycle racks Set $ 580.00
comprising of 3mm to 5mm thick galvanised steel,
approximate size of 2100mm x 2100mm (bicycle loaded
on upper tier) and 3100mm x 1600mm (bicycle on an
incline of extended tier), including make good affected
area, painting works and removal of old bicycle racks
SOR 78 / 131
Schedule of Rates
G 181 Mild steel such as flats, round bar, angles, tees, Kg $ 6.70
channels, hollow sections, square sections, rivets and
bolts, etc. of any size fabricated and fixed including
welding or bolting (for structural steel work only, eg:
linkway column, beam, roof trusses etc.)
G 182 Mild steel flats, round bar, angles, tees, channels, hollow Kg $ 4.90
sections, rivets and bolts, etc. of any size fabricated and
fixed including welding or bolting (for non-structural steel
work only, eg: banner structure, bollard post etc)
G 183 Extra over mild steel rods, flats, angles, tees, channels, Kg $ 1.00
hollow sections, rivets, bolts, etc. for galvanising in lieu of
painting one coat of lead and chromate-free primer.
G 184 Extra over mild steel rods, flats, angles, tees, channels, Kg $ 1.00
hollow sections, rivets, bolts, etc. for hot-dipped
galvanising.
G 185 Supply and fix 75mm diameter Class "C" mild steel pipe No $ 47.00
as litter bin post not exceeding 1m in height from ground
level with top & bottom capping welded together including
excavation & embedding 300mm in concrete (1:2:4)
foundation, bracket for hanging bins and 1 coat of primer
and 2 coats of enamel paint.
Galvanised Mesh
G 186 Supply and fix galvanised mesh, 3.3mm B.G. 50mm x m2 $ 18.00
50mm weldmesh (ref No. 2210) complete with wood
frame with fillets including painting.
G 187 Supply and fix galvanised mesh, 3.3mm B.G. 50mm x m2 $ 32.00
50mm weldmesh (ref No. 2210) complete with steel
frame with fillets including painting.
G 188 Supply and fix 1.2mm thk 12.5 x 12.5mm (ref 5518) m2 $ 10.00
galvanised mesh to ventilated gap/opening.
SOR 79 / 131
Schedule of Rates
Zinc Sheets
Signage
G 191 Supply and fix metal house number plate sizes No $ 1.80
approximately 32mm x 57mm with number of alphabet
embossed including all necessary painting.
G 192 Supply and fix plastic house number plates sizes approx. No $ 0.80
40mm x 60mm height per digit.
G 193 Remove signage plates (any size) from walls and return No $ 10.30
to Town Council Office on instruction of Superintending
Officer including making good works disturbed.
G 194 Reinstall signage plates (any size) on wall with all No $ 10.70
necessary fixing accessories.
Clothes Rack
G 197 Supply and install 38mm diameter galvanised steel tubing Each $ 5.10
as clothes drying racks, 225mm long one end splayed
and the other end welded to plate including necessary
hacking, reinstatement and painting.
G 198 Supply and install 38mm diameter galvanised iron tubing Each $ 6.30
as clothes drying racks, 460mm long one end splayed
and the other end let into concrete or brickwall including
all necessary hacking, reinstatement and painting.
SOR 80 / 131
Schedule of Rates
Bollards
G 199 Supply and fix 100mm diameter Class "C" mild steel pipe No $ 77.80
as bollards with height varying from 1.0m to 1.5m from
ground level with top and bottom capping welded together
including excavation and embedding 300mm in concrete
(1:2:4) foundation and 1 coat primter and 2 coats of
enamel paint.
G 200 Supply and fix 100mm diameter 3mm thick grade No $ 182.40
stainless steel pipe as bollards with height varying from
1.0m to 1.2m from ground level with top capped welded
including excavation and embedded in concrete
foundation (300 x 300 x 300)mm
G 202 Supply and fix galvanised or wrought iron bollard chain Kg $ 6.00
including hooks, rings, staples, etc.
Chequered Plate
G 204 Supply and fix galvanised mild steel chequered plate, cut m2 $ 64.30
to size, including all welding on site 2.5mm thk (net plate
thickness)
SOR 81 / 131
Schedule of Rates
Vents
G 212 Supply and fix aluminium fixed louverd vent to services m2 $ 219.10
room, etc. complete with 2.3mm thick extruded aluminium
louvred blades & frames/mullion necessary fixing
accessories as shown in drawing no. AMKTC-D25
G 213 Supply and fix Grade 304 stainless steel communal Set $ 730.90
refuse chute hopper to centralise refuse chute complete
with all necessary fixing accessories as specified.
G 214 Supply and fix Grade 304 stainless steel refuse chute No $ 306.60
hopper's cover to suit existing stainless steel hopper
including stainless steel hinges.
G 215 Supply and fix stainless steel pin for stainless steel No $ 8.10
hopper.
G 216 Supply and fix approved (Gauge 14) aluminium refuse No $ 65.50
chute hopper (movable body) to existing aluminium
hopper frame including aluminium frame hinges.
G 217 Supply and fix aluminium hinges for aluminium hopper No $ 4.60
including pop rivettings to cover and hopper and all
necessary felt.
G 218 Remove and fix back aluminium rivet for front panel for Set $ 1.50
the replacement of foot-pedal mechanism part.
G 219 Service air cylinder and linkage joints including lubricating No $ 16.50
and cleaning (exclude replacement of parts)
SOR 82 / 131
Schedule of Rates
G 229 Replace foot pedal including lubricating all joints within No $ 76.40
the compartment.
Notice Board
G 231 Supply & fix 3mm thick clear transparent polycarbonate m2 $ 80.00
cover complete with necessary fixing accessories for
notice board
G 234 Supply and fix 2mm thick adhesive board backing m2 $ 45.00
G 236 Supply and fix 5mm thick clear polycarbonate or acrylic m2 $ 92.50
plastic sheet in panel to Notice Board including rubber
glazing where necessary
G 237 Supply and fix 12.7mm thick soft board velvet fabric to m2 $ 51.00
Notice Board
G 238 Remove notice board and store in Town Council office or No $ 20.20
as directed including making good disturbed work
SOR 83 / 131
Schedule of Rates
G 239 Supply and fix 25mm x 3mm x 230mm long galvanised No $ 1.10
wrought iron holdfast one end turned up and screwed to
frame, other end fishtailed and slot into wall.
G 240 Cut into existing wall and fix 25mm x 3mm x 230mm long No $ 4.50
galvanised wrought iron holdfast
Ramset Nail
G 241 Supply and fix ramset nail No.2330 or other approved No $ 0.50
including the use of gun and explosives.
Staircase Nosing
G 242 Supply and fix Stainless steel stair nosing size 50mm x m $ 16.10
35mm x 1mm thick of grade 304 with fishtail holdfast
bedded in prepacked mortar all as specified in detailed
drawing no. AMKTC-D30
Catladder
SOR 84 / 131
Schedule of Rates
Flushout Pipe
G 248 Supply and fix additional brackets to external flush out No $ 21.70
pipes and external main risers with anchors set in brick
wall or concrete wall in detailed drawing no. AMKTC-D29
(Gondola and scaffolding to be paid separately)
G 249 Supply and fix 50mm (external diameter) 2mm thick m $ 52.00
grade 304 stainless steel pipe for banner/games court
post complete with hooks including bedded in 300 x 300 x
300mm concrete (1:2:4) footing (length measured nett
from surface)
G 251 Supply and fix stainless steel flag pole comprising the No $ 965.00
following:
SOR 85 / 131
Schedule of Rates
G 258 Extra over item 252 to 257 for curving of composite panel m2 $ 19.50
Powder Coating
G 262 Supply and fix 31.8mm x 1.5mm stainless steel pipe No $ 34.30
grade 304 to existing galvanised pipe socket at the
external parapet wall including cutting off existing pipe,
pump in Hilti RE-500 adhesive and make good all works
disturbed
SOR 86 / 131
Schedule of Rates
G 263 Supply and fix 31.8mm x 1.5mm stainless steel pipe No $ 47.50
grade 304 to existing galvanised pipe socket at the
external parapet wall by drilling/coring 35mm diameter
through internal wall surface, pump in Hilti RE-500
adhesive and make good all works disturbed
G 264 Extra over for item 262 to 263 for cutting the existing No $ 16.50
galvanised pipe socket at the external parapet wall with
and sealing off with non-shrink grout to flush with wall and
make good all works disturbed.
Galvanised Stud
SOR 87 / 131
Schedule of Rates
G 280 Supply and fix hot -dipped galvanised steel drain grating, m2 $ 344.00
fabricated by 50 x 8mm flat bar as frame; welded with 25
x 8mm intermediate flat bars vertically spaced at 18mm
interval; resting on 25 x 8mm flat bar at 200mm interval.
G 281 Supply and fix hot -dipped galvanised steel drain grating, m2 $ 307.00
fabricated by 50 x 8mm flat bar as frame; welded with 25
x 8mm intermediate flat bars horizontally spaced at 9mm
interval; resting on 25 x 8mm flat bar at 200mm interval.
G 282 Supply and fix overall size hot-dipped galvanised steel m2 $ 451.00
hinged drain grating, fabricated by 50 x 50 x 4.5mm angle
bar and 44 x 8mm flat bar as frame; welded with 25 x
8mm intermediate flat bars vertically spaced at 18mm
intervall; resting on 25 x 8mm flat bars at 200mm interval.
G 283 Supply and fix overall size hot-dipped galvanised steel m2 $ 410.00
hinged drain grating, fabricated by 50 x 50 x 4.5mm angle
bar and 44 x 8mm flat bar as frame; welded with 25 x
8mm intermediate flat bars horizontally spaced at 9mm
intervall; resting on 25 x 8mm flat bars at 200mm interval.
G 284 Remove front panel of foot operated refuse hopper, Job $ 49.00
replace 2 no. stainless steel spring, service air cylinder
and linkage joints, lubricating, cleaning and refix front
panel.
G 285 Remove front panel of foot operated refuse hopper, Job $ 137.00
replace air cylinder (OD 25mm shaft 10mm diameter
stroke 150mm) and 2 no. stainless steel spring, service
linkage joints, lubricating, cleaning and refix front panel.
G 286 Remove front panel of foot operated refuse hopper, Job $ 139.00
replace air cylinder (OD 32mm shaft 12mm diameter
stroke 160mm) and 2 no. Stainless steel spring, service
linkage joints, lubricating, cleaning and refix front panel.
SOR 88 / 131
Schedule of Rates
MISCELLANEOUS
Protective Barrier / Hoarding
G 289 Supply and install 1m high PVC barrier mesh with 50 x m $ 4.30
50mm timber posts as shown in drawing no. AMKTC-D33
G 290 Supply and install 1m high PVC barrier mesh with 50 x m $ 5.00
50mm timber posts complete with concrete base as
shown in drawing no.
AMKTC-D33
Incense Burner
G 291 Supply and deliver to site incense paper burner fabricated No $ 52.90
from 44 gallon drum with top or side opening complete
with hinged door, 2 nos. 9mm dia. mild steel handles,
25mm dia. perforated hole at not more than 100mm c/c in
3 row (min) with 2210 galvanised mesh base netting
supported by four legged stand and finish with 2 coats of
lead and chromate free primer.
G 292 Supply and deliver to site incense paper burner fabricated No $ 39.10
from 44 gallon drum with top opening and 25mm dia.
perforated hole at not more than 100mm c/c in 3 row
(min) with 2210 galvanised mesh base netting supported
by four legged stand and finish with 2 coats of lead and
chromate free primer.
G 293 Supply and deliver to site incense burners fabricated from No $ 59.00
44 gallon drum fitted with expanded mesh cover on top
with bolt and nuts, and side opening completed with
hinged doors, 2 nos 9mmø mild steel handles, 25mmø
perforated hole in 3 row with galvanized mesh base
netting supported by four legged stand and finish with
primer coat.
G 295 Supply and deliver stainless steel low emission incense No $ 170.00
burner (cylinder shaped) as shown in drawing no. AMKTC-
D82
SOR 89 / 131
Schedule of Rates
Plastering
H 005 Extra over plastering for forming 20 x 15mm deep groove m $ 2.00
lines to wall, columns, beams etc as specified
Glazed Tiling
H 008 108 x 108 mm white glazed tiling to walls including coved m2 $ 43.50
or rounded edged tiles etc and prepacked screed
H 009 150 x 150 mm white glazed tiling to walls including coved m2 $ 45.00
or rounded edged tiles etc and prepacked screed
SOR 90 / 131
Schedule of Rates
H 012 100 x 200 mm white glazed tiling to walls including coved m2 $ 48.10
or rounded edge tiles etc and prepacked screed
H 013 100 x 200 mm or 200mm x 200mm white based floral tile m2 $ 44.90
to wall including coved or rounded edged tiles etc and
prepacked screed
Homogeneous/Ceramic Tiling
H 015 Supply and lay ceramic tiles (Heavy Duty) of any sizes m2 $ 43.20
minimum 8mm thick including coved or round edges of
approved colour and pattern, jointed, pointed, on and
including minimum 13mm thick prepacked screed backing
to wall
H 016 Supply and lay homogeneous polished wall tiles of any m2 $ 60.15
sizes minimum 8mm thick including coved or round edge
tiles of approved colour and pattern, jointed, pointed on
and including backing to wall prepacked screed
H 017 Supply and lay homogeneous unpolished wall tiles of any m2 $ 44.80
sizes minimum 8mm thick including coved or round edge
tiles of approved colour and pattern, jointed, pointed on
and including minimum 13mm thick backing to wall
H 019 Exceeding 0.3m2 and not exceeding 0.5m2 per patch No $ 32.60
H 020 Exceeding 0.5m2 and not exceeding 1m2 per patch No $ 65.20
Mosaic Tiling
H 021 Supply and lay unglazed mosaic tiles 19mm x 19mm or m2 $ 46.20
25mm x 25mm walls including coved tiles etc and
prepacked screed
SOR 91 / 131
Schedule of Rates
H 023 Supply and lay glazed mosaic tiling to walls including m2 $ 57.80
coved and rounded edge tiles etc and prepacked screed
Terrazzo
H 024 Supply and lay 20mm thick terrazzo on brick, block or m2 $ 45.00
concrete walls, column surface polished including
prepacked mortar screed not exceeding 20mm thick and
brass/plastic dividing strips where necessary.
Slate Tiling
H 025 Supply and lay natural slate tiles of 10-15mm thick in any m2 $ 40.00
approved colours and pattern jointed and pointed on and
including 13mm thick prepacked screed backing to wall.
Granite Tiling
H 026 Supply and lay 10mm-13mm thick polished granite slabs m2 $ 122.00
of approved colour and pattern, jointed, pointed on and
including minimum 13mm thick prepacked screed backing
to wall.
H 028 Supply and lay 15mm thick pebble wash finish (pebble m2 $ 42.00
size 3mm to 5mm) to wall, columns, etc. laid in section
including provision of all necessary groove lines
Spalling Concrete
H 029 Hack 13mm `V' groove along crack, apply primer and m $ 12.40
patching with epoxy mortar including painting (inclusive of
related works covered in the drawing and specification)
SOR 92 / 131
Schedule of Rates
H 033 Extra over item H032 for area exceeding 0.65m2 m2 $ 205.50
H 035 Repair to cracks by hacking "V" groove along cracks and m $ 16.00
patch with approved polyurethane sealant including
painting to the repaired surface.
Hacking Works
H 036 Hack out cracks in concrete walls, slabs, soffits and floors m $ 3.70
to form "V" shaped grooves approximately 25mm wide x
37mm deep, make good with prepacked mortar and touch
up paintwork to match existing
Patching Works
H 040 Exceeding 0.02 and not exceeding 0.1 metre square per No $ 5.70
patch
SOR 93 / 131
Schedule of Rates
Skim Coating
Miscellaneous
H 047 Supply labour for laying tiles (any grades, sizes, colours m2 $ 26.20
and patterns) including 13mm prepacked screed and
pointing to wall.
H 048 Pull out nails, hooks etc from walls and ceilings and patch No $ 0.50
up hole including touching up painting to match existing.
H 050 Prepare and wash with high water jet and hypochloride m2 $ 3.00
acid or approved detergent to remove all surface
contaminants on all surfaces.
SOR 94 / 131
Schedule of Rates
H 059 Extra over for item H052 for painting of one coat of SS345 Job $ 6.50
to minimum of treatment area of 5m2
H 060 Extra over for item H053 for painting of one coat of SS345 Job $ 13.00
to minimum of treatment area of 10m2
H 061 Extra over for item H054 for painting of one coat of SS345 Job $ 26.00
to minimum of treatment area of 20m2
H 062 Extra over for item H055 for painting of one coat of SS345 Job $ 39.00
to minimum of treatment area of 30m2
H 063 Extra over for item H056 for painting of one coat of SS345 Job $ 52.00
to minimum of treatment area of 40m2
H 064 Extra over for item H057 for painting of one coat of SS345 m2 $ 1.30
to minimum of treatment area of 50m2
H 065 Supply and lay sedimentary/ textured coating for column m2 $ 25.00
or walls
SOR 95 / 131
Schedule of Rates
GLAZIER
(To be read in conjunction with preambles)
Glass Panes
* Ordinary quality clear sheet/obscured glass etc. to
timber/steel/aluminium windows/doors/vents/partitions
including all removal and make good of the area *(001-
022)
SOR 96 / 131
Schedule of Rates
Glass Louvres
I 027 Provide and apply putty for securing glass panes to metal m
$ 1.20
windows
I 029 Labour for taking out lock from tempered glass door, No
repair, oil and ease lock and refix in position with proper $ 7.60
alignment
Fibre-Glass Railing
SOR 97 / 131
Schedule of Rates
PAINTER
(To be read in conjunction with preambles)
SOR 98 / 131
Schedule of Rates
SOR 99 / 131
Schedule of Rates
J 030 Painting one undercoat and one finishing coat of synthetic No $ 30.00
paint to external surface of timber door including door
frames to door openings not exceeding 3m2
J 031 Painting one finishing coat of synthetic enamel paint to all No $ 22.00
faces of m.s gate to door opening not exceeding 3m2
Aluminium Paint
J 042 Two coats (with maximum 10% dilution for first coat, and m2 $ 1.90
without water dilution on second coat)
J 043 Three coats (with maximum 10% dilution for first coat, m2 $ 2.60
and without water dilution on second and third coats)
J 045 Two coats (with maximum 10% dilution for first coat, and m2 $ 2.45
without water dilution on second coat)
J 046 Three coats (with maximum 10% dilution for first coat and m2 $ 3.30
without dilution to second and third coats)
Pesticide Paint
J 048 Two coats (with maximum 5% dilution for first coat and m2 $ 3.10
without water dilution on second coat
Bituminous Paint
J 050 Mild steel drain cover gratings dipped in Bitutect No. 1 or m2 $ 2.50
approved bituminous paint (rate inclusive of both faces)
Varnish To Woodwork
J 054 Stain, prepare and apply 2 coats shellac varnish on new m2 $ 7.90
or existing woodwork
J 055 Prepare and apply two coats of approved stain and wax m2 $ 6.10
polish or polyurethane varnish on general surfaces of
woodwork
Spray Paint
J 064 Add to (or deduct from) for each 25mm high over (or No $ 0.25
under) 75mm
Wood Preservative
Miscellaneous
J 077 Brush, wash down and apply one coat water-based m2 $ 1.05
sealer on concrete or plastered surfaces.
J 078 Paint existing column edge angle bar at carpark using m $ 1.70
illuminated/fluorescent paint.
J 081 Paint existing table tennis top and exposed edges with 2 No $ 45.00
coats approved paint, mark out new lines and 2 coats of
enamel paint to steel hollow section frames
J 084 Apply one coat of rust inhabitor primer to metal surface to m2 $ 3.30
receive new coating
Road Base
Bituminous Premix
K 009 For every 25mm thick over (or under) 75mm thick of Type m2 $ 3.30
B1
Road Repairs
Road Hump
Kerb
Divider
K 031 Supply and install flexible road line divider including No $ 141.30
excavation, grade 30 concrete footing with reinforcement
and all necessary accessories.
(Drawing No. AMKTC-D42)
K 032 Supply and install flexible road line divider including all No $ 101.00
necessary accessories.
(Drawing No. AMKTC-D42)
Aeration Slab
K 039 Supply labour for taking out existing loose carpark m2 $ 11.80
aeration slabs, select from stack and re-lay slabs
including compacting ground with additional sand to
required level; filling voids and joints with top soil and
plant with cow grass and remove all debris from site.
(New slab measured separately)
K 042 Labour for only for relaying existing carpark aeration slab m2 $ 4.80
including compacting ground with additional sand to
required level.
BG Slab
TURF PAVERS
K 045 Supply and lay 475mm x 475mm x 100mm precast turf m2 $ 37.10
pavers (TP100) on 40mm sand bed to car park or tree
planting area including filling all voids with approved top
soil and turf and all necessary excavation, trimming and
cart away surplus earth and debris from site.
K 046 Supply and lay 450 x 450 x 100mm interlocking turf paver m2 $ 50.00
on 40mm sand bed to car park or tree planting area
including filing all voids with approved to soil and turf and
all necessary excavation, trimming and cart away surplus
earth and debris from site.
DAYWORK
(To be read in conjunction with preambles)
LABOUR
PLANT
L 024 Motor Lorry (Pick-up) not more than 2.50 tonne including Hr $ 18.30
fuel and driver
L 025 Motor Lorry 3 tonne size including fuel and driver Hr $ 25.60
L 026 Motor Lorry 7 tonne size including fuel and driver Hr $ 31.90
L 028 Motor Lorry mounted with crane including fuel and Hr $ 29.40
operator (6½ tonne lifting capacity)
L 029 Motor Lorry mounted with crane including fuel and Hr $ 38.00
operator (10 tonne lifting capacity)
L 030 Air compressor with air delivery capacity not less than 4 Hr $ 21.10
cu m per minute including pneumatic tools, fuel and tool
sharpening (no labour)
L 041 Supply and install mechanical suspended cradle not Unit $ 835.00
exceeding 5 metres length to the roof including PE
endorsement certifying the proper installation of
suspended cradle according to the PE's design
calculations, drawings and roof plans, application /
submission of electricity supply to various authorities for
approval by licensed electrical worker (hiring charges and
shifting shall be paid separately)
Mobile Scaffold
L 043 Mobile scaffold compliance with safety regulations and Per $ 115.00
taking down after use (the height of the mobile scaffold Job
must not exceed 3 times its lesser base dimension) (per
job duration)
L 044 Add for item L043 for labour in dismantling, shifting to No $ 57.50
new location and re-erection.
Timber Scaffold
Metal Scaffold
L 050 Carry out test of mobile lifting platform by approved Test $ 396.75
person (PE Structural Engineer and PE Mechanical
Engineer) from the relevant authorities
L 051 Supply and install Single Mast Mobile Lifting platform not Unit $ 1,058.00
exceeding 11 metres length including subsequent
removal off site upon completion of work, making good to
affected area (hiring changes shall be paid separately)
L 056 Labour for shifting approved Drive Unit Mast Platform shift $ 920.00
including supervision by Professional Engineer
Note:
The Hiring charge for Self-propelled Aerial
Platform/Boomlift (item 057 to 072) to be paid will be
based on the minimum amount calculated using daily,
weekly and monthly rates
L 073 Pull out test for plaster (Per point for external) point $ 92.00
L 074 Pull out test for plaster (Per point for internal) point $ 92.00
L 075 Pull out test for brick tile (Per point for 200 x 200mm) point $ 115.00
L 089 Supply and erect safety barricade comprising of orange job $ 80.00
netting and post supports complete with danger signs to
cordon off the site as and when instructed by the
Superintending Officer including subsequent removal
from site for barricade area up to 60m2.
L 094 Area exceeding 100m² but not exceeding 300m2 Blk $ 1,158.00
L 095 Area exceeding 300m² but not exceeding 600m2 Blk $ 1,905.00
L 096 Area exceeding 600m² but not exceeding 900m2 Blk $ 2,820.00
L 099 For every 100 numbers in excess of 200 numbers item $ 180.00
L 102 Extra over for item 101 for every 10 units exceeding the Item $ 60.00
120 units (Rate not subject to tender adjustment)
M 003 300mm diameter R.C. stool complete with glazed mosaic No $ 86.80
tiles finish on all exposed surface as specified in drawing
no.AMKTC-D56, D57, D58.
M 004 600mm diameter R.C. stool complete with glazed mosaic No $ 145.60
tiles finish on all exposed surface as specified in drawing
no. AMKTC-D59
M 005 300mm diameter R.C. stool complete with terrazzo finish No $ 68.30
on all exposed surface as specified in drawing
no.AMKTC-D56, D57, D58.
M 006 600mm diameter R.C. stool complete with terrazzo finish No $ 125.80
on all exposed surface as specified in drawing no.
AMKTC-D59
RC Bench
M 012 R.C. Type "A" bench with back rest and 850mm diameter No $ 1,090.00
R.C. table complete with 50 x 50 glazed mosaic tile finish
on all exposed surfaces all as specified in detailed
drawing no.AMKTC-D65 & AMKTC-D66
M 013 R.C. Type "B" bench with back rest and complete with 50 No $ 764.00
x 50 glazed mosaic tile finish on all exposed surface all as
specified in detailed drawing no. AMKTC-D65 & AMKTC-
D66
M 014 1.20m x 0.6m R.C. bench with round curved end and No $ 239.00
300mm thick curved reinforced concrete supports finish
with terrazzo on all exposed surfaces including
excavation and 600 x 600 x 300mm deep concrete (1:2:4)
footing foundation in detailed drawing no.
AMKTC-D39 (Concrete slab measured separately)
M 015 1.20m x 0.6m R.C. bench with centre divider and two No $ 246.00
100mm thick reinforced concrete supports finish with
glazed mosaic on all exposed surfaces including
excavation and 2 Nos. 600 x 300 x 300mm deep concrete
(1:2:4) footing foundation in detailed drawing no. AMKTC-
D67 (Concrete slab measured separately)
M 019 Supply and install park bench with kapur slats and cast No $ 163.80
iron powder coated frame (635mm x 600mm) at location
as directed by the SO including painting, varnishing, fixing
accessories, carting away earth, etc. as shown in
drawing no. AMKTC-D71
M 020 Supply and install park bench with kapur slats and cast No $ 226.00
iron powder coated frame (635mm x 1200mm) at location
as directed by the SO including painting, varnishing, fixing
accessories, etc. as specified and as shown in drawing
no. AMKTC-D71
M 021 Supply and install timber bench with 6 nos. balau slats No $ 360.00
(50 x 100)mm and powder- coated welded steel frame at
location as directed by SO including painting, varnishing
as shown in drawing no.
AMKTC-D72
M 022 Supply, delivery and install park table with kapur slats and No $ 275.40
cast iron powder coated frame (1380mm x 720mm x
690mm) at location as directed by the SO including
painting, varnishing, fixing accessories, etc. as shown in
drawing no. AMKTC-D71
M 023 Supply, deliver and install 2-seater cast aluminium bench No $ 415.00
at location as directed by Superintending Officer
M 024 Supply, deliver and install 1-seater cast aluminium bench No $ 260.00
at location as directed by Superintending Officer
M 025 Supply, deliver and install Chengal timber BBQ table cum No $ 713.00
bench (1500mm x 1200mm) at location as directed by the
Superintending Officer including painting and varnishing
and as shown in drawing no.AMKTC-D73
M 026 Supply, deliver and install balau timber garden table with No $ 233.00
cast iron powder coated frame (1220mm x 600mm x
630mm) at location as directed by the Superintending
Officer including painting, varnishing and fixing
accessories as shown in drawing no.
AMKTC-D71
M 033 Supply and install of composite timber slats to the existing No $ 245.00
bench top as shown in drawing no AMKTC-D75 . Size of
propose composite timber slats for bench top 168 x
20mm thick x 1830mm (L) x 2pcs and 49mm x 20mm x
1830mm (L) x 1pc (centre slat). Size of composite timber
bone / support 30 x 16 x 385mm (L) x 7pcs.
M 043 Supply and install 1-seater plastic coated bench with No $ 420.00
armrest
M 044 Supply and install 2-seater plastic coated bench with No $ 820.00
armrest
M 045 Supply and install 3-seater plastic coated bench with No $ 1,200.00
armrest
M 046 Supply and install plastic coated 1067mm diameter table Set $ 1,650.00
top complete with 4 plastic coated seats with backrest
M 048 Standard table tennis table with mild steel hollow frame Set $ 238.50
as shown on Standard Drawing including removal of
existing fixture where necessary and making good of
affected area as shown in drawing no.
AMKTC-D79
M 049 Standard table tennis table top including removal of Set $ 125.00
existing fixture where necessary and making good of
affected area.
Play/Fitness Equipment
M 051 Supply and fix stainless steel chain for swing seat. m $ 12.10
M 052 Supply and fix thick Swing seat complete with fish plates. No $ 19.10
M 053 Supply and fix rubber tyres including bracket as swing No $ 31.80
seat (without galvanised chain)
M 055 Supply and fix 50mm thick see-saw seat size No $ 106.00
approximately 4.3m long x 250mm wide including
supplying new bolts, "U" brackets for holders, etc and
fixing to existing supports.
M 056 Supply and fix rubber stopper to underside and sea-saw No $ 6.60
M 057 Supply and fix see-saw "U" shaped handle of 16mm No $ 17.40
round bar, 280mm high and 170mm wide complete with
washers, bolts and nuts.
M 060 Supply and fix standard climbing nylon rope 32mm No $ 42.80
diameter including fixing of brackets.
M 061 Supply and fix standard nylon netting size 2.3m x 2.3m No $ 327.10
consisting of 32mm diameter nylon rope tied together with
approved knot to form a net to match existing.
M 062 Supply and install to fitness corner balau treated timber No $ 1,784.00
for pressure impregnation with a suitable wood
preservative to an average dry salt retention of 5.6 kg/m3
and complying with SS72 and treated in accordance with
SS CP1.
Games Court
M 071 Supply and fix acrylic basketball board size 1800 x 1200 x Pair $ 1,495.00
18mm thick.
M 072 Supply and fix marine plywood basketball board size Pair $ 800.00
1800 x 1200 x 20mm thick.
M 073 Supply and fix standard basketball court ring (without net) No $ 40.30
M 077 Supply and fix 50mm to 75mm diameter Class "C" mild Pair $ 99.00
steel pipe standard games court post complete with
hooks for Sepak Takraw / Badminton Court including
excavation, casting of concrete footing (if necessary), 3
coats enamel paint.
Pebbles
M 079 Supply, deliver and lay on site smooth pebbles (any Kg $ 1.20
colour) of size 10 - 50mm as specified by SO (concrete
base and top screed measured separately)
M 080 Supply, deliver and lay on site smooth grey or black Kg $ 1.10
pebbles of size 40mm and above as specified by SO
(concrete base and top screed measured separately)
Sub-Soil
M 087 Supply and lay 100mm diameter UPVC drain out pipe in m $ 9.90
trench for incense paper burner pit including all
necessary excavation and loosen rubble packing around.
Miscellaneous
M 091 Rub down, clean, polish and wax all exposed surfaces of m2 $ 8.20
terrazzo work such as slide, chess table and stool etc.
M 092 Supply and fix selected polish granite top of 20mm thick m2 $ 345.00
with bevel or round edge mount onto bench by adhesive
or bonding cement including removal of existing damage
granite finished granite top.
M 094 Supply and install 50mm diameter Class "B" galvanised No $ 119.00
steel pipe as bird hanging pole, height varies from 5 to 6
metre from ground level with top end of pipe bend
600mm and the bottom end welded with a 200 x 200 x
6mm thick steel plate encasted with 250 x 250 x 600mm
high concrete foundation (Total length of pipe ranges
from 6.2 to 7.2 metre long) including excavation, forming
150mm diameter cement skirting, nylon rope complete
with pulleys and hooks.
Bollards
M 097 Supply and install reinforced concrete bollard Grade 20 of No $ 189.00
approximate size 300mm dia. 750mm (h) with 300mm
wide black and yellow bands as shown on standard
drawing no. AMKTC-D83
Repair of Leaks
N 006 For area not exceeding 3.5m2 (per unit) Job $ 122.50
Floor Finishes
N 013 For area not exceeding 3.5m2 (per unit) Job $ 191.00
N 015 For area not exceeding 3.5m2 (per unit) Job $ 220.00
N 017 For area not exceeding 3.5m2 (per unit) Job $ 189.00
*Waterproofing *(020-022)
PILING WORKS
(To be read in conjunction with preambles)
Piling Rigs
Bakau Piles
Kempas Piles
* Supply and fix 5mm mild steel welded box sleeve *(012-
015)
Pile Test