Professional Documents
Culture Documents
Prop95R052 3
Prop95R052 3
Measuring results
For evaluation of the measurement data,
refer to your local Wärtsilä
representative.
Validity / Issue
Until further notice.
Before taking any action, always check
CONFIDENTIAL the available on-line systems for the
latest revision of this document. Any
This document and its content are strictly confidential. locally stored or printed version is
No part of this document may be reproduced or copied in considered to be an uncontrolled
any form or by any means, nor disclosed to any third document.
parties.
Wärtsilä Netherlands BV
PO Box 6 5150 BB, Drunen
CONFIDENTIAL RECORDS
Document history
Issue Date Description SBWT ID
1 13-06-2012 Initial release
2 14-01-2016 Prepare for PDF form
3 10-01-2019 Format update
Contents
Page
Document history 2
Contents 2
1 Blade carrier and sliding block 4
2 Hub body 6
3 Yoke and propeller shaft 8
4 How to contact Wärtsilä 10
ATTENTION
All dimensions are stated at an object- and environment temperature of 20ºC. Always
work with calibrated measurement tooling and make sure it acclimatizes to the
environment of the measured component for two to four hours minimum. Contact
Technical Services if there is any doubt regarding temperature of the measured
components. If the object to be measured is transferred to a different environment,
allow sufficient time, depending on the object mass and shape, for the object to
acclimatize.
ATTENTION
Clearances are the leading criteria for acceptance or rejection, regardless of the
dimensions of the individual components. The actual dimensions of individual
components are to calculate this clearance, and to determine which part is worn, and
needs to be refurbished or replaced.
ATTENTION
All measurements must be taken in millimetres (mm) with an accuracy of 0.01 mm.
Otherwise the measurements are to be recalculated to mm: 1” (inch) = 25.4mm.
NOTE
The stated nominal dimensions have no relation to the measured values and are for
measuring tool selection only
CONFIDENTIAL RECORDS
Ship’s name :
IMO number :
Functional location :
Installation number :
Equipment number :
Date of overhaul :
Running hours :
For evaluation of the measurement data, refer to your local Wärtsilä representative.
CONFIDENTIAL RECORDS
NOTE
Always measure dimension K, L, M, N and P in clockwise order
Measurement Nominal
dimension (mm)
K 296
L 80
M 41.5
N 80
P 107
CONFIDENTIAL RECORDS
Visual check
remark
CONFIDENTIAL RECORDS
2 Hub body
NOTE
Always measure dimension A, B and D in clockwise order
Measurement Nominal
dimension (mm)
A 296
B 41.5
D 260
CONFIDENTIAL RECORDS
Visual check
remark
CONFIDENTIAL RECORDS
NOTE
Always measure dimension E, F, G and J in clockwise order
Measurement Nominal
dimension (mm)
E 260
F 260
G 107
J 260
CONFIDENTIAL RECORDS
Visual check
remark
CONFIDENTIAL RECORDS
No part of this publication may be reproduced or copied in any form or by any means (electronic, mechanical, graphic, photocopying, recording,
taping or other information retrieval systems) without the prior written permission of the copyright holder. Wärtsilä Netherlands B.V. makes no
representation, warranty (express or implied) in this publication and assumes no responsibility for the correctness, errors or omissions for
information contained herein. Information in this publication is subject to change without notice.
Unless otherwise expressly set forth, no recommendation contained in this document or any of its appendices is to be construed as provided
due to a defect of the product, but merely as an improvement of the product, operating instructions and/or the maintenance procedures
relating thereto. Any actions by the owner/operator as a result of the recommendations are not covered under any warranty provided by
Wärtsilä and such actions will thus be at the owners/operators own cost and expense.
NO LIABILITY WHETHER DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL, IS ASSUMED WITH RESPECT TO THE
INFORMATION CONTAINED HEREIN. THIS PUBLICATION IS CONFIDENTIAL AND INTENDED FOR INFORMATION PURPOSES
ONLY.