Professional Documents
Culture Documents
EA - Check of Short-Term & Long-Term Deflections ACI 318M-14 v1.0
EA - Check of Short-Term & Long-Term Deflections ACI 318M-14 v1.0
COMPANY ADDRESS
WEBSITE
Job No: xxx-xxxx Sheet No: 01
Page Type: CALCULATION SHEET Prepared By: EA Date: 01/06/24
Section: SERVICEABILITY REQUIREMENTS Checked By: EA Revision: 00
Section Properties
Width of Comp. Face of Member, b = 1000 mm
Overall Height of The Member, h = 300 mm
Tension Reinforcement Cover, Ct = 50 mm
Compression Reinforcement Cover, Cc = 50 mm
Area of Tension Reinforcement, As = 2010 mm2
Area of compression reinforcement, As' = 2010 mm2
Ratio of Tension Reinforcement, ρ = 0.80%
Ratio of Compression Reinforcement, ρ' = 0.80%
Span Length of The Member, L = 8000 mm
Modular Ratio of Elasticity, n = Es/Ec = 7.52 PCA Notes on ACI 318-11 (Table 10-2)
Icr = b(kd)^3/3 + nAs(d-kd)2+ (n-1)As'(kd-d')2 = 609466048 mm4 PCA Notes on ACI 318-11 (Table 10-2)
Deflection (Δ mm)
Members likely to be damaged by large deflections Total Deflection = Δsustained + ΔLL - Δown = 15.41
Members not likely to be damaged by large deflections Total Deflection = Δsustained + ΔLL = 18.75
Deflection Check
Member Condition Deflection to be considered limitation
L /180[1] (mm)
Flat roofs Immediate deflection due to maximum of Lr, S and R OK
Not supporting or attached to nonstructural elements = 44.44
likely to be damaged by large deflections L /360 (mm)
Floors Immediate deflection due to LL OK
= 22.22
Likely to be damaged by L /480 (mm)
[3]
[1]Limit not intended to safeguard against ponding. Ponding shall be checked by calculations of deflection, including added deflections due to ponded water, and
considering timedependent effects of sustained loads, camber, construction tolerances, and reliability of provisions for drainage.
[2]Time-dependent deflection shall be calculated in accordance with 24.2.4, but shall be permitted to be reduced by amount of deflection calculated to occur before
nonstructural elements. This amount shall be calculated on basis of accepted engineering data relating to time-deflection characteristics of members similar to those
being considered.
[3]Limit shall be permitted to be exceeded if measures are taken to prevent damage to supported or attached elements.
[4]Limit shall not exceed tolerance provided for nonstructural elements.
Check of Short-term and Long-term Deflections ACI 318M-14
This spreadsheet is prepared and developed by Ehab Attalla, BSc (Hons.) Civil, CEng
Disclaimer:
THE AUTHOR DISCLAIM ALL WARRANTIES RELATING TO THIS SPREADSHEET/SOFTWARE, WHETHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED
TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE AUTHOR SHALL NOT BE LIABLE FOR ANY INDIRECT,
CONSEQUENTIAL, OR INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH SPREADSHEET/SOFTWARE, EVEN IF THE AUTHOR HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR CLAIMS. THE PERSON USING THE SPREADSHEET/SOFTWARE BEARS ALL RISK AS TO THE
QUALITY AND PERFORMANCE OF THE SPREADSHEET/SOFTWARE.
ALTHOUGH EVERY EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS SPREADSHEET/SOFTWARE, USERS SHOULD VERIFY THE RESULTS FOR
THEMSELVES.
Revision History:
Revision Date(yyyy/mm/dd) Description
0 10/2/2020 Check of Short-term and Long-term Deflections ACI 318M-14 v1.0
###
Total Mactual =
2dB=
(1+rd'/d)
Table 10-2 Gross and Cracked Moment of Inertia of Rectangular and Flanged Section
(1+r)2=
[2dB(1+rd'/d)+(1+r)2]^0.5=
{[2dB(1+rd'/d)+(1+r)2]^0.5-(1+r)=
Kd={[2dB(1+rd'/d)+(1+r)2]^0.5-(1+r)}/B =
b (kd)^3/3 =
nAs(d-kd)2 =
(n-1)As'(kd-d')2=
Icr= b(kd)^3/3+nAs(d-kd)2+(n-1)As'(kd-d'