Professional Documents
Culture Documents
EU Igus Dry-Tech BEA1 2023 Catalogue 02-05 Iglidur Food Contact
EU Igus Dry-Tech BEA1 2023 Catalogue 02-05 Iglidur Food Contact
EN 09/2023
Bearing technology | Plain bearings | iglidur® Contact with food
Plain bearing materials for contact with food Temperature [°C] 123) +80 – +
Price index – +
Price index – +
Price index – +
EN 09/2023
EN 09/2023
123)
Upper long-term application temperature 124)
Max. recommended surface pressure at +20°C 125)
Best pairing for p = 1 MPa,
v = 0.3m/s, rotating
398 3D-CAD, finder and service life calculation ... www.igus.eu/A181 Lubrication-free made easy ... from stock ... no minimum order quantity 399
The universal bearing for food contact
Compliant with Regulation (EU)
No. 10/2011 and FDA guidelines
iglidur A181 ®
EN 09/2023
iglidur® A181 iglidur® A181
+90°C +90°C
31MPa 31MPa
Bearing technology | Plain bearings | iglidur® A181 Technical data
General properties Testing method
Bar stock,
Compliant with Regulation (EU) No. 10/2011 Compressive strength MPa 60
Max. permissible surface pressure (+20°C) MPa 31
round bar
Page 743 and FDA guidelines Shore D hardness 76 DIN 53505
Physical and thermal properties
The iglidur® A181 material is compliant with Regulation (EU) No. 10/2011 and also with FDA specifications. Max. application temperature long-term °C +90
The blue colour also facilitates the "optical detectability" often desired in the food sector. FOOD
Max. application temperature short-term °C +110
● Compliant with Regulation (EU) No. 10/2011 Min. application temperature °C -50
Bar stock, ● FDA-compliant Thermal conductivity W/m · K 0.25 ASTM C 177
plate ● Universal installation
Page 773 Coefficient of thermal expansion (at +23°C) K-1 · 10-5 11 DIN 53752
● High media resistance Electrical properties
● Wear-resistant Specific transitional resistance Ωcm > 1012 DIN IEC 93
● Lubrication-free Surface resistance Ω > 1012 DIN 53482
● Maintenance-free
Table 01: Material properties
tribo-tape liner
Page 781 Typical application areas
Due to their technical specifications and their conformity Resistance to weathering
● Food industry
with the relevant regulations, iglidur® A181 plain bearings iglidur® A181 plain bearings are resistant to weathering.
● Beverage technology
are predestined for applications in food technology. The material properties are slightly affected. Discolouration
● Medical technology
Compared to iglidur® A180 with regard to the mechanical occurs.
properties, temperature and media resistance, iglidur® A181
is more suitable with respect to the wear resistance in Mechanical properties
Guide rings
Page 641 most cases. With increasing temperatures, the compressive strength of
iglidur® A181 plain bearings decreases. Diagram 02 shows
Descriptive technical specifications Moisture absorption this inverse relationship. The maximum recommended
Wear resistance at +23°C – + The moisture absorption of iglidur® A181 plain bearings is surface pressure is a mechanical material parameter. No
approximately 0.2 % weight in standard climatic conditions. conclusions regarding the tribological properties can be
Wear resistance at +90°C – +
The saturation limit submerged in water is 1.3% weight. drawn from this.
Two hole Wear resistance at +150°C – + This must be taken into account for these types of Diagram 03 shows the elastic deformation of iglidur® A181
flange
bearings applications. at radial loads.
Page 667 Slide property – +
Surface pressure, page 45
Wear resistance under water – + Vacuum
In vacuum, any present moisture is released as vapour. Use Permissible surface speeds
Media resistance – +
in vacuum is only possible with dehumidified iglidur® A181 iglidur® A181 was developed for low surface speeds.
Moulded Resistant to edge pressures – + bearings. Maximum speeds of up to 0.8m/s (rotating) and 3.5m/s
special parts
Page 696 (linear), respectively, are permissible during continuous dry
Resistant to shock and impact loads – +
Radiation resistance operation. The given values in table 03 indicate the limits
Dirt resistance – + Plain bearings made from iglidur® A181 are resistant up to at which an increase up to the continuous permissible
a radiation intensity of 2 · 10² Gy. temperature occurs. This increase is a result of friction. In
practice, though, this level is rarely reached, due to varying
application conditions.
igubal® Online product finder Online service life calculation
Surface speed, page 48
EN 09/2023
EN 09/2023
spherical balls
Page 993 www.igus.eu/iglidur-finder www.igus.eu/iglidur-expert
402 3D-CAD, finder and service life calculation ... www.igus.eu/A181 Lubrication-free made easy ... from stock ... no minimum order quantity 403
iglidur® A181 iglidur® A181
+90°C +90°C
31MPa 31MPa
Bearing technology | Plain bearings | iglidur® A181 Technical data
100.0 0.26
Chemicals Resistance
0.23
Temperature Alcohols + 10.0
H.a. aluminium
20 1.5
Coefficient of friction and surfaces, page 51
Dry Greases Oil Water
Cf53 steel
15
Wear [µm/km]
Wear resistance, page 54 1.0
Coefficient of friction μ 0.10-0.21 0.08 0.03 0.04 10
Load [MPa]
0.5
Table 04: Coefficient of friction against steel (Ra = 1μm, 5
Shaft materials 0 0.0
50HRC)
Diagram 06 shows results of testing different shaft 20 30 40 50 60 70 80 90
materials with plain bearings made from iglidur® A181. Temperature [°C]
Housing Plain bearings Shaft
Particular attention is paid in the food industry to the Diagram 02: Maximum recommended surface pressure as a Diagram 06: Wear, rotating with different shaft materials,
Ø d1 [mm] H7 [mm] E10 [mm] h9 [mm]
corrosion-resistant shaft types. Diagram 06 shows that function of temperature (31MPa at +20°C) pressure, p = 1MPa, v = 0.3m/s
0-3 +0.000 +0.010 +0.014 +0.054 -0.025 +0.000
very low wear rates can be achieved in combination with
> 3-6 +0.000 +0.012 +0.020 +0.068 -0.030 +0.000
these shafts. As with many of the iglidur® materials, wear 10 200
> 6-10 +0.000 +0.015 +0.025 +0.083 -0.036 +0.000
rate increases with otherwise identical parameters in rotating
> 10-18 +0.000 +0.018 +0.032 +0.102 -0.043 +0.000 8 oscillating
rotation (diagram 07). +23°C 150
> 18-30 +0.000 +0.021 +0.040 +0.124 -0.052 +0.000
Shaft materials, page 56 6 +60°C
> 30-50 +0.000 +0.025 +0.050 +0.150 -0.062 +0.000 100
Deformation [%]
> 50-80 +0.000 +0.030 +0.060 +0.180 -0.074 +0.000 4
Wear [µm/km]
Installation tolerances 50
> 80-120 +0.000 +0.035 +0.072 +0.212 -0.087 +0.000 2
iglidur® A181 plain bearings are standard bearings for
> 120-180 +0.000 +0.040 +0.085 +0.245 -0.100 +0.000
shafts with h-tolerance (recommended minimum h9). The 0 0
Table 05: Important tolerances for plain bearings according
bearings are designed for press-fit into a housing machined 0 5 10 15 20 25 30 35 0 15 30 45
to ISO 3547-1 after press-fit
to a H7 tolerance. After being assembled into a nominal Load [MPa] Load [MPa]
size housing, the inner diameter automatically adjusts to Diagram 03: Deformation under pressure and temperature Diagram 07: Wear for oscillating and rotating applications
the E10 tolerances. with shaft material Cf53 hardened and ground steel, as a
Testing methods, page 61 function of the load
0.4
Coefficient of friction [µ]
0.3
0.2
0.1
0.0
0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50
Surface speed [m/s]
Diagram 04: Coefficient of friction as a function of the
EN 09/2023
EN 09/2023
404 3D-CAD, finder and service life calculation ... www.igus.eu/A181 Lubrication-free made easy ... from stock ... no minimum order quantity 405
iglidur® A181 iglidur® A181
+90°C +90°C
31MPa 31MPa
Bearing technology | Plain bearings | iglidur® A181 Product range
Sleeve bearings (form S) d1 d1 d2 b1 Part No. d1 d1 d2 b1 Part No.
Tolerance3) h13 Tolerance3) h13
f1
30°
[mm] [mm] [mm] [mm] [mm] [mm]
32.0 36.0 40.0 A181SM-3236-40 45.0 50.0 20.0 A181SM-4550-20
35.0 39.0 20.0 A181SM-3539-20 45.0 50.0 30.0 A181SM-4550-30
d1
d2
0.5
35.0 39.0 30.0 A181SM-3539-30 45.0 50.0 40.0 A181SM-4550-40
35.0 39.0 40.0 A181SM-3539-40 45.0 50.0 50.0 A181SM-4550-50
30°
+0.050 +0.050
b1 35.0 39.0 50.0 A181SM-3539-50 50.0 55.0 20.0 A181SM-5055-20
+0.150 +0.150
40.0 44.0 20.0 A181SM-4044-20 50.0 55.0 30.0 A181SM-5055-30
40.0 44.0 30.0 A181SM-4044-30 50.0 55.0 40.0 A181SM-5055-40
2)
Thickness < 0.6mm: chamfer = 20° 40.0 44.0 40.0 A181SM-4044-40 50.0 55.0 50.0 A181SM-5055-50
Chamfer in relation to d1 40.0 44.0 50.0 A181SM-4044-50 50.0 55.0 60.0 A181SM-5055-60
d1 [mm] Ø 1-6 Ø 6-12 Ø 12-30 Ø > 30 Dimensions according to ISO 3547-1 and 3)
After press-fit. Testing methods, page 61
f1 [mm] 0.3 0.5 0.8 1.2 special dimensions
EN 09/2023
3)
After press-fit. Testing methods, page 61 above €150.
406 3D-CAD, finder and service life calculation ... www.igus.eu/A181 Lubrication-free made easy ... from stock ... no minimum order quantity 407
iglidur® A181
+90°C
31MPa
Bearing technology | Plain bearings | iglidur® A181
Flange bearings (form F)
.5
.0
ax
f1
30
rm
°
d2
d3
d1
b2
b1
2)
Thickness < 0.6mm: chamfer = 20°
Chamfer in relation to d1
d1 [mm] Ø 6-12 Ø 12-30 Ø > 30 Dimensions according to ISO 3547-1 and
f1 [mm] 0.5 0.8 1.2 special dimensions
8.0 10.0 15.0 10.0 1.00 A181FM-0810-10 18.0 20.0 26.0 22.0 1.00 A181FM-1820-22
+0.025
10.0 12.0 18.0 7.0 1.00 A181FM-1012-07 20.0 23.0 30.0 11.5 1.50 A181FM-2023-11
+0.083
10.0 12.0 18.0 9.0 1.00 A181FM-1012-09 20.0 23.0 30.0 16.5 1.50 A181FM-2023-16
10.0 12.0 18.0 10.0 1.00 A181FM-1012-10 20.0 23.0 30.0 21.5 1.50 A181FM-2023-21 When to use it?
10.0 12.0 18.0 12.0 1.00 A181FM-1012-12 25.0 28.0 35.0 11.5 1.50 A181FM-2528-11 ● When FDA compliance is required
10.0 12.0 18.0 17.0 1.00 A181FM-1012-17 25.0 28.0 35.0 16.5 1.50 A181FM-2528-16 ● When wear resistance and FDA-compliance are necessary at high loads
12.0 14.0 20.0 7.0 1.00 A181FM-1214-07 25.0 28.0 35.0 21.5 1.50 A181FM-2528-21 ● When the bearing is used in acid environments
+0.040
12.0 14.0 20.0 9.0 1.00 A181FM-1214-09 30.0 34.0 42.0 16.0 2.00 A181FM-3034-16
+0.124
12.0 14.0 20.0 12.0 1.00 A181FM-1214-12 30.0 34.0 42.0 26.0 2.00 A181FM-3034-26
+0.032
12.0 14.0 20.0 17.0 1.00 A181FM-1214-17 35.0 39.0 47.0 16.0 2.00 A181FM-3539-16
+0.102 When not to use it?
14.0 16.0 22.0 12.0 1.00 A181FM-1416-12 35.0 39.0 47.0 26.0 2.00 A181FM-3539-26
14.0 16.0 22.0 17.0 1.00 A181FM-1416-17 40.0 44.0 52.0 30.0 2.00 A181FM-4044-30 ● When temperatures are continuously higher than +180°C
15.0 17.0 23.0 9.0 1.00 A181FM-1517-09 40.0 44.0 52.0 40.0 2.00 A181FM-4044-40 iglidur® A500
45.0 50.0 58.0 50.0 2.50 A181FM-4550-50 ● When the maximum wear resistance is necessary
iglidur® J
3)
After press-fit. Testing methods, page 61
● When a cost-effective FDA-compliant plain bearing is required
iglidur® A200, iglidur® A180
● For high speeds
iglidur® J
EN 09/2023
EN 09/2023
Bar stock,
in the food sector Compressive strength MPa 78
Max. permissible surface pressure (+20°C) MPa 60
round bar
Page 743 Compliant with Regulation (EU) No. 10/2011 and Shore D hardness 76 DIN 53505
FDA guidelines Physical and thermal properties
A universal plain bearing for use in the area of food and pharmaceutical industries. Composition of Max. application temperature long-term °C +180
FOOD
FDA-compliant materials allows the use in areas where other plain bearings cannot be used due to the Max. application temperature short-term °C +210
contact with food. With good tribological and mechanical properties, iglidur® A350 plain bearings are Min. application temperature °C -100
Bar stock, suitable for all-round use in and around food machinery. Thermal conductivity W/m · K 0.24 ASTM C 177
plate
Page 773 ● Compliant with Regulation (EU) No. 10/2011 Coefficient of thermal expansion (at +23°C) K-1 · 10-5 8 DIN 53752
● FDA-compliant Electrical properties
● Temperature-resistant up to +180°C Specific transitional resistance Ωcm > 1011 DIN IEC 93
● Suitable for medium and high loads Surface resistance Ω > 1011 DIN 53482
● Suitable for pivoting applications Table 01: Material properties
tribo-tape liner ● Lubrication-free
Page 781
● Standard range from stock iglidur® A350 plain bearings are made for practically all Resistance to weathering
● Suitable for rotating applications loads in food and packaging machinery. Even high loads, iglidur® A350 plain bearings are continuously resistant
● Maintenance-free often seen in lifting equipment, are taken easily and the to weathering. The material properties are only slightly
bearings work flawlessly without any external lubrication. affected. Possible discolourations are only superficial.
Typical application areas
● Food industry Moisture absorption Mechanical properties
Guide rings
Page 641 ● Beverage technology The moisture absorption of iglidur® A350 is low and can be When temperatures increase, the compressive strength of
● Medical technology ignored when using standard plain bearings. Even when iglidur® A350 plain bearings decreases. Diagram 02 shows
saturated with water, iglidur® A350 does not absorb more this inverse relationship. The maximum recommended
Descriptive technical specifications than 1.9% weight of water (by weight). surface pressure is a mechanical material parameter. No
Wear resistance at +23°C – + conclusions regarding the tribological properties can be
Vacuum drawn from this.
Two hole Wear resistance at +90°C – +
In vacuum, any present moisture is released as vapour. Use Diagram 03 shows the elastic deformation of iglidur® A350
flange
bearings Wear resistance at +150°C – + in vacuum is only possible with dehumidified iglidur® A350 under different loads. At the recommended maximum
Page 667
bearings. surface pressure of 60MPa the deformation is less than
Slide property – +
5% at room temperature.
Wear resistance under water – + Radiation resistance Surface pressure, page 45
Plain bearings made from iglidur® A350 are resistant up to
Media resistance – +
Moulded a radiation intensity of 2 · 10² Gy.
special parts
Page 696 Resistant to edge pressures – +
Dirt resistance – +
EN 09/2023
spherical balls
Page 993 www.igus.eu/iglidur-finder www.igus.eu/iglidur-expert
410 3D-CAD, finder and service life calculation ... www.igus.eu/A350 Lubrication-free made easy ... from stock ... no minimum order quantity 411
iglidur® A350 iglidur® A350
+180 °C +180 °C
60MPa 60MPa
Bearing technology | Plain bearings | iglidur® A350 Technical data
Permissible surface speeds 100.0 0.19
Chemicals Resistance
0.17
iglidur® A350 plain bearings are suitable for low and Alcohols + 10.0
H.a. aluminium
2.5
40
2.0
Cf53 steel
Dry Greases Oil Water
Wear [µm/km]
Friction and wear 1.5
Coefficient of friction μ 0.10-0.20 0.09 0.04 0.04 20
Load [MPa]
1.0
The coefficient of friction of iglidur® A350 on a steel shaft 0.5
Table 04: Coefficient of friction against steel (Ra = 1μm,
is in the mid range (diagrams 04 and 05). 0 0.0
50HRC)
Coefficient of friction and surfaces, page 51 20 40 60 80 100 120 140 160 180
Wear resistance, page 54 Temperature [°C]
Housing Plain bearings Shaft
Diagram 02: Maximum recommended surface pressure as a Diagram 06: Wear, rotating with different shaft materials,
Ø d1 [mm] H7 [mm] F10 [mm] h9 [mm]
Shaft materials function of temperature (60MPa at +20°C) pressure, p = 1MPa, v = 0.3m/s
0-3 +0.000 +0.010 +0.006 +0.046 -0.025 +0.000
The corrosion-resistant steels are rather considered
> 3-6 +0.000 +0.012 +0.010 +0.058 -0.030 +0.000
a natural choice for use in the food industry. The trials 6 25
> 6-10 +0.000 +0.015 +0.013 +0.071 -0.036 +0.000
were therefore carried out especially on such materials. It ■ Cf53 ■ 304 stainless steel
> 10-18 +0.000 +0.018 +0.016 +0.086 -0.043 +0.000 5 20 ■ High grade steel
has been shown that there is no clear favourite and 304 +23°C
> 18-30 +0.000 +0.021 +0.020 +0.104 -0.052 +0.000 4
stainless steel, high grade steel and hard-chromed steel +60°C 15
> 30-50 +0.000 +0.025 +0.025 +0.125 -0.062 +0.000 3
are all suitable. Hard-anodised aluminium is also well suited
Deformation [%]
> 50-80 +0.000 +0.030 +0.030 +0.150 -0.074 +0.000 10
Wear [µm/km]
for both linear and rotational movements. 2
> 80-120 +0.000 +0.035 -0.036 +0.176 -0.087 +0.000 5
Shaft materials, page 56 1
> 120-180 +0.000 +0.040 +0.043 +0.203 +0.000 +0.100
0 0
Table 05: Important tolerances for plain bearings according
Installation tolerances 0 10 20 30 40 50 60 1.0 2.0 3.0 4.0 5.0
to ISO 3547-1 after press-fit
iglidur® A350 plain bearings are standard bearings for Load [MPa] Load [MPa]
shafts with h tolerance (recommended minimum h9). Diagram 03: Deformation under pressure and temperature Diagram 07: Wear, rotating with different shaft materials, as a
The bearings are designed for press-fit into a housing function of the load
machined to a H7 tolerance. After being assembled into a
nominal size housing, in standard cases the inner diameter 0.4
0.0
0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50
Surface speed [m/s]
Diagram 04: Coefficient of friction as a function of the
EN 09/2023
EN 09/2023
412 3D-CAD, finder and service life calculation ... www.igus.eu/A350 Lubrication-free made easy ... from stock ... no minimum order quantity 413
iglidur® A350 iglidur® A350
+180 °C +180 °C
60MPa 60MPa
Bearing technology | Plain bearings | iglidur® A350 Product range
Sleeve bearings (form S) d1 d1 d2 b1 Part No. d1 d1 d2 b1 Part No.
Tolerance3) h13 Tolerance3) h13
f1
30°
[mm] [mm] [mm] [mm] [mm] [mm]
32.0 36.0 20.0 A350SM-3236-20 40.0 44.0 50.0 A350SM-4044-50
32.0 36.0 30.0 A350SM-3236-30 45.0 50.0 20.0 A350SM-4550-20
d1
d2
0.5
32.0 36.0 40.0 A350SM-3236-40 45.0 50.0 30.0 A350SM-4550-30
35.0 39.0 20.0 A350SM-3539-20 45.0 50.0 40.0 A350SM-4550-40
30°
b1 35.0 +0.025 39.0 30.0 A350SM-3539-30 45.0 +0.025 50.0 50.0 A350SM-4550-50
35.0 +0.125 39.0 40.0 A350SM-3539-40 50.0 +0.125 55.0 20.0 A350SM-5055-20
35.0 39.0 50.0 A350SM-3539-50 50.0 55.0 30.0 A350SM-5055-30
2)
Thickness < 0.6mm: chamfer = 20° 40.0 44.0 20.0 A350SM-4044-20 50.0 55.0 40.0 A350SM-5055-40
Chamfer in relation to d1 40.0 44.0 30.0 A350SM-4044-30 50.0 55.0 50.0 A350SM-5055-50
d1 [mm] Ø 1-6 Ø 6-12 Ø 12-30 Ø > 30 Dimensions according to ISO 3547-1 and 40.0 44.0 40.0 A350SM-4044-40 50.0 55.0 60.0 A350SM-5055-60
f1 [mm] 0.3 0.5 0.8 1.2 special dimensions 3)
After press-fit. Testing methods, page 61
EN 09/2023
3)
After press-fit. Testing methods, page 61 above €150.
414 3D-CAD, finder and service life calculation ... www.igus.eu/A350 Lubrication-free made easy ... from stock ... no minimum order quantity 415
iglidur® A350
+180 °C
60MPa
Bearing technology | Plain bearings | iglidur® A350
Flange bearings (form F)
.5
.0
ax
f1
30
rm
°
d2
d3
d1
b2
b1
2)
Thickness < 0.6mm: chamfer = 20°
Chamfer in relation to d1
d1 [mm] Ø 1-6 Ø 6-12 Ø 12-30 Ø > 30 Dimensions according to ISO 3547-1 and
f1 [mm] 0.3 0.5 0.8 1.2 special dimensions
8.0 10.0 15.0 9.5 1.00 A350FM-0810-09 18.0 20.0 26.0 17.0 1.00 A350FM-1820-17
10.0 10.0 15.0 10.0 1.00 A350FM-0810-10 20.0 23.0 30.0 11.5 1.50 A350FM-2023-11
+0.013
10.0 12.0 18.0 7.0 1.00 A350FM-1012-07 20.0 23.0 30.0 16.5 1.50 A350FM-2023-16
+0.071 When to use it?
10.0 12.0 18.0 9.0 1.00 A350FM-1012-09 20.0 23.0 30.0 21.5 1.50 A350FM-2023-21
10.0 12.0 18.0 10.0 1.00 A350FM-1012-10 25.0 +0.020 28.0 35.0 11.5 1.50 A350FM-2528-11 ● When FDA compliance is required
10.0 12.0 18.0 12.0 1.00 A350FM-1012-12 25.0 +0.104 28.0 35.0 16.5 1.50 A350FM-2528-16 ● When a high chemical resistance is required
10.0 12.0 18.0 17.0 1.00 A350FM-1012-17 25.0 28.0 35.0 21.5 1.50 A350FM-2528-21 ● Abrasion-resistant
12.0 14.0 20.0 7.0 1.00 A350FM-1214-07 30.0 34.0 42.0 16.0 2.00 A350FM-3034-16 ● Temperature-resistant from -100°C to +250°C
12.0 14.0 20.0 9.0 1.00 A350FM-1214-09 30.0 34.0 42.0 26.0 2.00 A350FM-3034-26
12.0 +0.016 14.0 20.0 12.0 1.00 A350FM-1214-12 35.0 39.0 47.0 16.0 2.00 A350FM-3539-16
12.0 +0.086 14.0 20.0 17.0 1.00 A350FM-1214-17 35.0 39.0 47.0 26.0 2.00 A350FM-3539-26
+0.025 When not to use it?
14.0 16.0 22.0 12.0 1.00 A350FM-1416-12 40.0 44.0 52.0 30.0 2.00 A350FM-4044-30
+0.125 ● When the highest wear resistance is required
14.0 16.0 22.0 17.0 1.00 A350FM-1416-17 40.0 44.0 52.0 40.0 2.00 A350FM-4044-40
45.0 50.0 58.0 50.0 2.00 A350FM-4550-50 iglidur® X6, iglidur® Z
● When no resistance to temperature or chemicals is required
3)
After press-fit. Testing methods, page 61
iglidur® A180, iglidur® A200
● When a cost-effective universal plain bearing is required
iglidur® G, iglidur® P
EN 09/2023
EN 09/2023
Bar stock,
food sector Compressive strength MPa 118
Max. permissible surface pressure (+20°C) MPa 120
round bar
Page 743 Compliant with Regulation (EU) No. 10/2011 and Shore D hardness 83 DIN 53505
FDA guidelines Physical and thermal properties
Max. application temperature long-term °C +250
FOOD
Plain bearings made from iglidur® A500 can be exposed to extremely high temperatures and are suitable Max. application temperature short-term °C +300
for direct contact with food (FDA-compliant). Min. application temperature °C -100
Bar stock, ● Compliant with Regulation (EU) No. 10/2011 Thermal conductivity W/m · K 0.24 ASTM C 177
plate
Page 773 ● FDA-compliant Coefficient of thermal expansion (at +23°C) K-1 · 10-5 9 DIN 53752
● Temperature-resistant from -100°C to +250°C Electrical properties
● Chemical-resistant Specific transitional resistance Ωcm > 1014 DIN IEC 93
● Lubrication-free Surface resistance Ω > 1013 DIN 53482
● Maintenance-free Table 01: Material properties
tribo-tape liner
Page 781
Typical application areas Plain bearings made from iglidur® A500 can be used at high Resistance to weathering
● Food industry temperatures and are permitted for use in direct contact iglidur® A500 plain bearings are resistant to weathering.
● Beverage technology with food (FDA-compliant). They exhibit an exceptionally The material properties are significantly affected.
● Medical technology good chemical resistance and are suitable for heavy-duty Discolouration occurs. Practical tests under real application
use in and around machinery for the food industry. Though conditions are strongly recommended.
iglidur® A500 is a soft material, it possesses an excellent
Guide rings
Page 641 compressive strength even at high temperatures. Mechanical properties
When temperatures increase, the compressive strength of
Descriptive technical specifications Moisture absorption iglidur® A500 plain bearings decreases. Diagram 02 shows
Wear resistance at +23°C – + The moisture absorption of iglidur® A500 plain bearings is this inverse relationship. The maximum recommended
only 0.5% weight after saturation in water. surface pressure is a mechanical material parameter. No
Wear resistance at +90°C – +
conclusions regarding the tribological properties can be
Two hole Wear resistance at +150°C – + Vacuum drawn from this.
flange
bearings In vacuum, any present moisture is released as vapour. Diagram 02 shows the maximum recommended surface
Page 667 Slide property – +
The use in vacuum is only possible to a limited extent. pressure of the bearing as a function of the temperature.
Wear resistance under water – + The combination of high stability and high flexibility acts
Radiation resistance very positively during vibrations and edge loads. As the
Media resistance – +
Plain bearings made from iglidur® A500 are resistant up to wear of the plain bearing rapidly escalates from pressures
Moulded Resistant to edge pressures – + a radiation intensity of 2 · 10⁵ Gy. of 10 to 20MPa, we recommend a particularly accurate
special parts
Page 696 testing of the application above these limits.
Resistant to shock and impact loads – +
Surface pressure, page 45
Dirt resistance – +
EN 09/2023
spherical balls
Page 993 www.igus.eu/iglidur-finder www.igus.eu/iglidur-expert
418 3D-CAD, finder and service life calculation ... www.igus.eu/A500 Lubrication-free made easy ... from stock ... no minimum order quantity 419
iglidur® A500 iglidur® A500
+250°C +250°C
120MPa 120MPa
Bearing technology | Plain bearings | iglidur® A500 Technical data
Permissible surface speeds 1,000 0.7
Chemicals Resistance
0.6
iglidur® A500 also permits high surface speeds due to its Alcohols + 100
H.a. aluminium
80 15
Application temperatures, page 53 12
Dry Greases Oil Water
Cf53 steel
60
Wear [µm/km]
Additional securing, page 53 9
Coefficient of friction μ 0.26-0.41 0.09 0.04 0.04 40
Load [MPa]
6
20 3
Table 04: Coefficient of friction against steel (Ra = 1μm,
Friction and wear 0 0
50HRC)
The coefficient of friction is dependent on the load that 20 50 80 120 150 200 250
acts on the bearing (diagrams 04 and 05). Temperature [°C]
Housing Plain bearings Shaft
Coefficient of friction and surfaces, page 51 Diagram 02: Maximum recommended surface pressure as a Diagram 06: Wear, rotating with different shaft materials,
Ø d1 [mm] H7 [mm] F10 [mm] h9 [mm]
Wear resistance, page 54 function of temperature (120MPa at +20°C) pressure, p = 1MPa, v = 0.3m/s
0-3 +0.000 +0.010 +0.006 +0.046 -0.025 +0.000
> 3-6 +0.000 +0.012 +0.010 +0.058 -0.030 +0.000
Shaft materials 10 200
> 6-10 +0.000 +0.015 +0.013 +0.071 -0.036 +0.000
Diagram 06 shows results of testing different shaft rotating
> 10-18 +0.000 +0.018 +0.016 +0.086 -0.043 +0.000 8 160 oscillating
materials with plain bearings made from iglidur® A500. The +23°C
> 18-30 +0.000 +0.021 +0.020 +0.104 -0.052 +0.000
combination "iglidur® A500/hard-chromed shaft" clearly 6 +60°C 120
> 30-50 +0.000 +0.025 +0.025 +0.125 -0.062 +0.000
stands out in rotating application. Up to about 2.0MPa,
Deformation [%]
> 50-80 +0.000 +0.030 +0.030 +0.150 -0.074 +0.000 4 80
Wear [µm/km]
the wear of this combination remains largely independent
> 80-120 +0.000 +0.035 -0.036 +0.176 -0.087 +0.000 2 40
of load. In pivoting applications with Cf53 shafts, the wear
> 120-180 +0.000 +0.040 +0.043 +0.203 +0.000 +0.100
resistance is better than in rotations under equal load. If 0 0
Table 05: Important tolerances for plain bearings according
the shaft material you plan on using is not shown in these 0 20 40 60 80 100 120 0 10 20 30 40 50
to ISO 3547-1 after press-fit
test results, please contact us. Load [MPa] Load [MPa]
Shaft materials, page 56 Diagram 03: Deformation under pressure and temperature Diagram 07: Wear for oscillating and rotating applications
with shaft material Cf53 hardened and ground steel, as a
Installation tolerances function of the load
iglidur® A500 plain bearings are standard bearings for 0.5
EN 09/2023
420 3D-CAD, finder and service life calculation ... www.igus.eu/A500 Lubrication-free made easy ... from stock ... no minimum order quantity 421
iglidur® A500 iglidur® A500
+250°C +250°C
120MPa 120MPa
Bearing technology | Plain bearings | iglidur® A500 Product range
Sleeve bearings (form S) d1 d1 d2 b1 Part No. d1 d1 d2 b1 Part No.
Tolerance3) h13 Tolerance3) h13
f1
30°
[mm] [mm] [mm] [mm] [mm] [mm]
30.0 +0.020 34.0 30.0 A500SM-3034-30 40.0 44.0 40.0 A500SM-4044-40
30.0 +0.104 34.0 40.0 A500SM-3034-40 40.0 44.0 50.0 A500SM-4044-50
d1
d2
0.5
32.0 36.0 20.0 A500SM-3236-20 45.0 50.0 20.0 A500SM-4550-20
32.0 36.0 30.0 A500SM-3236-30 45.0 50.0 30.0 A500SM-4550-30
30°
b1 32.0 36.0 40.0 A500SM-3236-40 45.0 50.0 40.0 A500SM-4550-40
+0.025
35.0 39.0 20.0 A500SM-3539-20 45.0 50.0 50.0 A500SM-4550-50
+0.025 +0.125
35.0 39.0 30.0 A500SM-3539-30 50.0 55.0 20.0 A500SM-5055-20
+0.125
2)
Thickness < 0.6mm: chamfer = 20° 35.0 39.0 40.0 A500SM-3539-40 50.0 55.0 30.0 A500SM-5055-30
Chamfer in relation to d1 35.0 39.0 50.0 A500SM-3539-50 50.0 55.0 40.0 A500SM-5055-40
d1 [mm] Ø 1-6 Ø 6-12 Ø 12-30 Ø > 30 Dimensions according to ISO 3547-1 and 40.0 44.0 20.0 A500SM-4044-20 50.0 55.0 50.0 A500SM-5055-50
f1 [mm] 0.3 0.5 0.8 1.2 special dimensions 40.0 44.0 30.0 A500SM-4044-30 50.0 55.0 60.0 A500SM-5055-60
3)
After press-fit. Testing methods, page 61
Order example: A500SM-0405-04 – no minimum order quantity.
A500 iglidur® material S Cylindrical M Metric 04 Inner Ø d1 05 Outer Ø d2 04 Total length b1
EN 09/2023
3)
After press-fit. Testing methods, page 61 above €150.
422 3D-CAD, finder and service life calculation ... www.igus.eu/A500 Lubrication-free made easy ... from stock ... no minimum order quantity 423
iglidur® A500
+250°C
120MPa
Bearing technology | Plain bearings | iglidur® A500
Flange bearings (form F)
.5
.0
ax
f1
30
rm
°
d2
d3
d1
b2
b1
2)
Thickness < 0.6mm: chamfer = 20°
Chamfer in relation to d1
d1 [mm] Ø 1-6 Ø 6-12 Ø 12-30 Ø > 30 Dimensions according to ISO 3547-1 and
f1 [mm] 0.3 0.5 0.8 1.2 special dimensions
4.0 8.0 12.0 6.0 2.00 A500FM-0408-06 15.0 17.0 23.0 17.0 1.00 A500FM-1517-17
+0.010
6.0 8.0 12.0 4.0 1.00 A500FM-0608-04 16.0 18.0 24.0 12.0 1.00 A500FM-1618-12
+0.058 +0.016
6.0 8.0 12.0 6.0 1.00 A500FM-0608-06 16.0 18.0 24.0 17.0 1.00 A500FM-1618-17
+0.086 When to use it?
6.0 8.0 12.0 8.0 1.00 A500FM-0608-08 18.0 20.0 26.0 12.0 1.00 A500FM-1820-12
8.0 10.0 15.0 5.5 1.00 A500FM-0810-05 18.0 20.0 26.0 17.0 1.00 A500FM-1820-17 ● When the bearings have direct contact with food
8.0 10.0 15.0 7.5 1.00 A500FM-0810-07 18.0 20.0 26.0 22.0 1.00 A500FM-1820-22 ● When FDA compliance is required
8.0 10.0 15.0 9.5 1.00 A500FM-0810-09 20.0 23.0 30.0 11.5 1.50 A500FM-2023-11 ● When a low noise level is required
8.0 10.0 15.0 10.0 1.00 A500FM-0810-10 20.0 23.0 30.0 16.5 1.50 A500FM-2023-16 ● When low moisture absorption is fundamental
+0.013
10.0 12.0 18.0 7.0 1.00 A500FM-1012-07 20.0 23.0 30.0 21.5 1.50 A500FM-2023-21
+0.071
10.0 12.0 18.0 9.0 1.00 A500FM-1012-09 25.0 28.0 35.0 11.5 1.50 A500FM-2528-11
+0.020
10.0 12.0 18.0 12.0 1.00 A500FM-1012-12 25.0 28.0 35.0 16.5 1.50 A500FM-2528-16
+0.104 When not to use it?
10.0 12.0 18.0 15.0 1.00 A500FM-1012-15 25.0 28.0 35.0 21.5 1.50 A500FM-2528-21
10.0 12.0 18.0 17.0 1.00 A500FM-1012-17 30.0 34.0 42.0 16.0 2.00 A500FM-3034-16 ● When the maximum wear resistance is necessary
12.0 14.0 20.0 7.0 1.00 A500FM-1214-07 30.0 34.0 42.0 26.0 2.00 A500FM-3034-26 iglidur® J
12.0 14.0 20.0 9.0 1.00 A500FM-1214-09 30.0 34.0 42.0 40.0 2.00 A500FM-3034-40 ● When temperatures are continuously higher than +80°C
12.0 14.0 20.0 12.0 1.00 A500FM-1214-12 35.0 39.0 47.0 16.0 2.00 A500FM-3539-16 iglidur® A350, iglidur® A500
12.0 14.0 20.0 13.0 1.00 A500FM-1214-13 35.0 39.0 47.0 26.0 2.00 A500FM-3539-26 ● When a cost-effective universal plain bearing is required
+0.016 iglidur® G, iglidur® P
12.0 14.0 20.0 15.0 1.00 A500FM-1214-15 35.0 +0.025 39.0 47.0 40.0 2.00 A500FM-3539-40
+0.086
12.0 14.0 20.0 17.0 1.00 A500FM-1214-17 40.0 +0.125 44.0 52.0 30.0 2.00 A500FM-4044-30
14.0 16.0 22.0 12.0 1.00 A500FM-1416-12 40.0 44.0 52.0 40.0 2.00 A500FM-4044-40
14.0 16.0 22.0 17.0 1.00 A500FM-1416-17 45.0 50.0 58.0 50.0 2.00 A500FM-4550-50
15.0 17.0 23.0 9.0 1.00 A500FM-1517-09
3)
After press-fit. Testing methods, page 61
EN 09/2023
EN 09/2023
Bar stock,
FDA-compliant Compressive strength MPa 78
round bar Max. permissible surface pressure (+20°C) MPa 28
Page 743 Shore D hardness 76 DIN 53505
FDA-compliant material for applications with low to medium loads in immediate environments of (or contact
with) food or drugs, as well as humidity. Physical and thermal properties
● FDA-compliant Max. application temperature long-term °C +90
FOOD
● Compliant with Regulation (EU) No. 10/2011 Max. application temperature short-term °C +110
● High media resistance Min. application temperature °C -50
Bar stock, ● Suitable for wet environments Thermal conductivity W/m · K 0.25 ASTM C 177
plate
Page 773 ● High wear resistance Coefficient of thermal expansion (at +23°C) K-1 · 10-5 11 DIN 53752
● Lubrication-free Electrical properties
● Maintenance-free Specific transitional resistance Ωcm > 1012 DIN IEC 93
Surface resistance Ω > 1011 DIN 53482
Typical application areas Table 01: Material properties
tribo-tape liner ● Food industry
Page 781
● Beverage technology Plain bearings made from iglidur ® A180 are suitable Resistance to weathering
● Medical technology for application in direct contact with food. They are iglidur® A180 plain bearings are resistant to weathering.
the ideal solution for bearing points on machines for The material properties are significantly affected. Severe
the food and packaging industry, medical equipment discolouration occurs. Applications with this material under
manufacturing, small household appliances, etc. Even weathering conditions are not recommended.
where wet cleaning contact occurs, the iglidur® A180
Guide rings
Page 641 is characterised by the lowest moisture absorption. Mechanical properties
With increasing temperatures, the compressive strength of
Descriptive technical specifications Moisture absorption iglidur® A180 plain bearings decreases. Diagram 02 shows
Wear resistance at +23°C – + The moisture absorption of iglidur® A180 plain bearings is this inverse relationship. The maximum recommended
approximately 0.2 % weight in standard climatic conditions. surface pressure is a mechanical material parameter. No
Wear resistance at +90°C – +
The saturation limit submerged in water is 1.3% weight. conclusions regarding the tribological properties can be
Two hole Wear resistance at +150°C – + This must be taken into account for these types of drawn from this.
flange
bearings applications. Diagram 03 shows the elastic deformation of iglidur® A180
Page 667 Slide property – +
at radial loads. At the maximum recommended surface
Wear resistance under water – + Vacuum pressure of 28MPa, the deformation is less than 2.5%.
In vacuum, any present moisture is released as vapour. Use A plastic deformation can be negligible up to this value.
Media resistance – +
in vacuum is only possible with dehumidified iglidur® A180 However, it is also dependent on the service time.
Moulded Resistant to edge pressures – + bearings. Surface pressure, page 45
special parts
Page 696 Resistant to shock and impact loads – +
Radiation resistance
Dirt resistance – + Plain bearings made from iglidur® A180 are resistant up to
a radiation intensity of 3 · 10² Gy.
EN 09/2023
spherical balls
Page 993 www.igus.eu/iglidur-finder www.igus.eu/iglidur-expert
426 3D-CAD, finder and service life calculation ... www.igus.eu/A180 Lubrication-free made easy ... from stock ... no minimum order quantity 427
iglidur® A180 iglidur® A180
+90°C +90°C
28MPa 28MPa
Bearing technology | Plain bearings | iglidur® A180 Technical data
Permissible surface speeds 100.0 0.3
Chemicals Resistance
iglidur® A180 was developed for low surface speeds. The Alcohols + 10.0
H.a. aluminium
2.0
15
Application temperatures, page 53 1.5
Dry Greases Oil Water
Cf53 steel
Wear [µm/km]
Additional securing, page 53 10
1.0
Coefficient of friction μ 0.05-0.23 0.09 0.04 0.04
Load [MPa]
5 0.5
Table 04: Coefficient of friction against steel (Ra = 1μm,
Friction and wear 0 0.0
50HRC)
Similar to wear resistance, the coefficient of friction µ also 20 30 40 50 60 70 80 90
changes with the surface speed and load (diagram 04 and Temperature [°C]
Housing Plain bearings Shaft
05). The coefficient of friction decreases with increasing Diagram 02: Maximum recommended surface pressure as a Diagram 06: Wear, rotating with different shaft materials,
Ø d1 [mm] H7 [mm] E10 [mm] h9 [mm]
load. function of temperature (28MPa at +20°C) pressure, p = 1MPa, v = 0.3m/s
0-3 +0.000 +0.010 +0.014 +0.054 -0.025 +0.000
Coefficient of friction and surfaces, page 51
> 3-6 +0.000 +0.012 +0.020 +0.068 -0.030 +0.000
Wear resistance, page 54 10 20
> 6-10 +0.000 +0.015 +0.025 +0.083 -0.036 +0.000
rotating
> 10-18 +0.000 +0.018 +0.032 +0.102 -0.043 +0.000 8 oscillating
Shaft materials +23°C 15
> 18-30 +0.000 +0.021 +0.040 +0.124 -0.052 +0.000
Diagram 06 shows a summary of the results of tests with 6 +60°C
> 30-50 +0.000 +0.025 +0.050 +0.150 -0.062 +0.000 10
different shaft materials executed with plain bearings made
Deformation [%]
> 50-80 +0.000 +0.030 +0.060 +0.180 -0.074 +0.000 4
Wear [µm/km]
of iglidur® A180. The combination "iglidur® A180 against 5
> 80-120 +0.000 +0.035 +0.072 +0.212 -0.087 +0.000 2
hard-anodised aluminium shaft" clearly stands out. It
> 120-180 +0.000 +0.040 +0.085 +0.245 -0.100 +0.000
attains good to excellent wear rates also with other shafts. 0 0
Table 05: Important tolerances for plain bearings according
With Cf53 shafts, the higher wear in pivoting applications is 0 5 10 15 20 0.25 0.75 2.00 5.00 10.00 20.00
to ISO 3547-1 after press-fit
exemplary compared to rotating applications (diagram 07). Load [MPa] Load [MPa]
Diagram 03: Deformation under pressure and temperature Diagram 07: Wear for oscillating and rotating applications
Shaft materials, page 56 with shaft material Cf53 hardened and ground steel, as a
function of the load
Installation tolerances 0.6
EN 09/2023
428 3D-CAD, finder and service life calculation ... www.igus.eu/A180 Lubrication-free made easy ... from stock ... no minimum order quantity 429
iglidur® A180 iglidur® A180
+90°C +90°C
28MPa 28MPa
Bearing technology | Plain bearings | iglidur® A180 Bearing technology | Plain bearings | iglidur® A180
Sleeve bearings (form S) Flange bearings (form F)
.5
.0
ax
f1
30
f1
rm
°
30°
d2
d3
d1
d1
d2
0.5
30°
b1 b2
b1
2)
Thickness < 0.6mm: chamfer = 20° 2)
Thickness < 0.6mm: chamfer = 20°
Chamfer in relation to d1 Chamfer in relation to d1
d1 [mm] Ø 6-12 Ø 12-30 Dimensions according to ISO 3547-1 and d1 [mm] Ø 1-6 Ø 6-12 Ø 12-30 Dimensions according to ISO 3547-1 and
f1 [mm] 0.5 0.8 special dimensions f1 [mm] 0.3 0.5 0.8 special dimensions
Order example: A180SM-0608-10 – no minimum order quantity. Order example: A180FM-0608-06 – no minimum order quantity.
A180 iglidur® material S Cylindrical M Metric 06 Inner Ø d1 08 Outer Ø d2 10 Total length b1 A180 iglidur® material F With flange M Metric 06 Inner Ø d1 08 Outer Ø d2 06 Total length b1
Available from stock Ordering note Available from stock Ordering note
Detailed information about delivery time online. Our prices are scaled according to order Detailed information about delivery time online. Our prices are scaled according to order
www.igus.eu/24 quantities, current prices can be found online. www.igus.eu/24 quantities, current prices can be found online.
EN 09/2023
430 3D-CAD, finder and service life calculation ... www.igus.eu/A180 Lubrication-free made easy ... from stock ... no minimum order quantity 431
The "food-classic" for low duty
FDA-compliant
iglidur A200 ®
EN 09/2023
iglidur® A200 iglidur® A200
+80°C +80°C
18MPa 18MPa
Bearing technology | Plain bearings | iglidur® A200 Technical data
General properties Testing method
Bar stock,
FDA-compliant Compressive strength MPa 54
round bar Max. permissible surface pressure (+20°C) MPa 18
Page 743 Shore D hardness 81 DIN 53505
FDA-compliant material for applications with low to medium loads in immediate environs of (or contact)
with food or drugs. Physical and thermal properties
● FDA-compliant Max. application temperature long-term °C +80
FOOD
● Suitable for contact with food Max. application temperature short-term °C +170
● Suitable for low surface speeds Min. application temperature °C -40
Bar stock, ● Lubrication-free Thermal conductivity W/m · K 0.24 ASTM C 177
plate
Page 773 ● Standard range from stock Coefficient of thermal expansion (at +23°C) K-1 · 10-5 10 DIN 53752
● Maintenance-free Electrical properties
● Thrust washers available only in imperial sizes, from page 1147 Specific transitional resistance Ωcm > 1013 DIN IEC 93
Surface resistance Ω > 1012 DIN 53482
Typical application areas Table 01: Material properties
tribo-tape liner ● Food industry
Page 781
Plain bearings made from iglidur® A200 are suitable for Radiation resistance
application in direct contact with food. Hence they are Plain bearings made from iglidur® A200 are resistant up to
the ideal solution for bearing requirements in machines for a radiation intensity of 1 · 10⁴ Gy.
the food industry, medical equipment manufacturing, for
small equipment for households, etc. As the incorporation Resistance to weathering
of solid lubricants is dispensed with in favour of food iglidur® A200 plain bearings are resistant to weathering.
Guide rings
Page 641 compatibility, the thermoplastic composition of iglidur® A200 The material properties are significantly affected. Severe
is especially adjusted for abrasion resistance. In addition discolouration occurs. Applications with this material under
Descriptive technical specifications the iglidur® A200 is characterised by its capacity to embed weathering conditions are not recommended.
Wear resistance at +23°C – + dirt and by its quiet operating behaviour. The good wear
properties, dirt resistance and the possibility for dry Mechanical properties
Wear resistance at +90°C – +
operation allow to replace elaborately sealed, lubricated When temperatures increase, the compressive strength of
Two hole Wear resistance at +150°C – + bearings for little costs. iglidur® A200 plain bearings decreases. Diagram 02 shows
flange
bearings this inverse relationship. The maximum recommended
Page 667 Slide property – +
Moisture absorption surface pressure is a mechanical material parameter. No
Wear resistance under water – + The humidity absorption of iglidur® A200 bearings amounts conclusions regarding the tribological properties can be
to about 1.5% weight in standard climatic conditions. The drawn from this.
Media resistance – +
saturation limit submerged in water is 7.6% weight. This Diagram 03 shows the elastic deformation of iglidur® A200
Moulded Resistant to edge pressures – + must be taken into account for these types of applications. under different loads. At the maximum recommended
special parts
Page 696 surface pressure of 18MPa, the deformation is less than
Resistant to shock and impact loads – +
Vacuum 2%. A plastic deformation can be negligible up to this
Dirt resistance – + In vacuum, any present moisture is released as vapour. value. However, it is also dependent on the service time.
The use in vacuum is only possible to a limited extent. Surface pressure, page 45
EN 09/2023
spherical balls
Page 993 www.igus.eu/iglidur-finder www.igus.eu/iglidur-expert
434 3D-CAD, finder and service life calculation ... www.igus.eu/A200 Lubrication-free made easy ... from stock ... no minimum order quantity 435
iglidur® A200 iglidur® A200
+80°C +80°C
18MPa 18MPa
Bearing technology | Plain bearings | iglidur® A200 Technical data
Permissible surface speeds 100.0 0.8
Chemicals Resistance
iglidur® A2000 was developed for low surface speeds. Alcohols + up to 0 10.0 0.6
Cf53 steel
Wear [µm/km]
Similar to wear resistance, the coefficient of friction µ also 2
Coefficient of friction μ 0.10-0.40 0.09 0.04 0.04 10
Load [MPa]
changes with the surface speed and load (diagrams 04 1
Table 04: Coefficient of friction against steel (Ra = 1μm,
and 05). 0 0
50HRC)
Coefficient of friction and surfaces, page 51 20 30 40 50 60 70 80
Wear resistance, page 54 Temperature [°C]
Housing Plain bearings Shaft
Diagram 02: Maximum recommended surface pressure as a Diagram 06: Wear, rotating with different shaft materials,
Ø d1 [mm] H7 [mm] D11 [mm] h9 [mm]
Shaft materials function of temperature (18MPa at +20°C) pressure, p = 1MPa, v = 0.3m/s
0-3 +0.000 +0.010 +0.020 +0.080 -0.025 +0.000
Diagram 06 and 07 display a summary of the results of
> 3-6 +0.000 +0.012 +0.030 +0.105 -0.030 +0.000
tests with different shaft materials executed with plain 10 70
> 6-10 +0.000 +0.015 +0.040 +0.130 -0.036 +0.000
bearings made of iglidur® A200. In pivoting applications 60 rotating
> 10-18 +0.000 +0.018 +0.050 +0.160 -0.043 +0.000 8 oscillating
below a load of 2MPa, the wear of iglidur® A200 plain +23°C 50
> 18-30 +0.000 +0.021 +0.065 +0.195 -0.052 +0.000
bearings is higher than in rotating applications with equal 6 +60°C
> 30-50 +0.000 +0.025 +0.080 +0.240 -0.062 +0.000 40
load. Here the HR carbon steel shaft is a positive exception.
Deformation [%]
4 30
> 50-80 +0.000 +0.030 +0.100 +0.290 -0.074 +0.000
Wear [µm/km]
Shaft materials, page 56 20
> 80-120 +0.000 +0.035 +0.120 +0.340 -0.087 +0.000 2
10
> 120-180 +0.000 +0.040 +0.145 +0.395 -0.100 +0.000
Installation tolerances 0 0
Table 05: Important tolerances for plain bearings according
iglidur® A200 plain bearings are standard bearings for 0 3 6 9 12 15 18 Cf53 hard 304SS HR carbon
to ISO 3547-1 after press-fit chromed steel
shafts with h tolerance (recommended minimum h9). The Load [MPa]
bearings are designed for press-fit into a housing machined Diagram 03: Deformation under pressure and temperature Diagram 07: Wear for rotating and oscillating applications
to a H7 tolerance. After being assembled into a nominal with different shaft materials, p = 2MPa
size housing, the inner diameter automatically adjusts to
the D11 tolerances. For particular dimensions the tolerance 1.0
EN 09/2023
436 3D-CAD, finder and service life calculation ... www.igus.eu/A200 Lubrication-free made easy ... from stock ... no minimum order quantity 437
iglidur® A200 iglidur® A200
+80°C +80°C
18MPa 18MPa
Bearing technology | Plain bearings | iglidur® A200 Product range
Sleeve bearings (form S) d1 d1 d2 b1 Part No. d1 d1 d2 b1 Part No.
Tolerance3) h13 Tolerance3) h13
f1
30°
[mm] [mm] [mm] [mm] [mm] [mm]
14.0 20.0 15.0 ASM-1420-15 22.0 28.0 15.0 ASM-2228-15
14.0 20.0 20.0 ASM-1420-20 22.0 28.0 20.0 ASM-2228-20
d1
d2
0.5
15.0 17.0 10.0 ASM-1517-10 22.0 28.0 30.0 ASM-2228-30
15.0 17.0 15.0 ASM-1517-15 24.0 30.0 15.0 ASM-2430-15
30°
b1 15.0 21.0 10.0 ASM-1521-10 24.0 30.0 20.0 ASM-2430-20
15.0 21.0 15.0 ASM-1521-15 24.0 30.0 30.0 ASM-2430-30
15.0 21.0 20.0 ASM-1521-20 25.0 28.0 12.0 ASM-2528-12
2)
Thickness < 0.6mm: chamfer = 20° 16.0 18.0 12.0 ASM-1618-12 25.0 28.0 20.0 ASM-2528-20
Chamfer in relation to d1 16.0 18.0 20.0 ASM-1618-20 25.0 30.0 20.0 ASM-2530-20
+0.050
d1 [mm] Ø 1-6 Ø 6-12 Ø 12-30 Ø > 30 Dimensions according to ISO 2795 and special 16.0 20.0 20.0 ASM-1620-20 25.0 30.0 30.0 ASM-2530-30
+0.160
f1 [mm] 0.3 0.5 0.8 1.2 dimensions 16.0 20.0 25.0 ASM-1620-25 25.0 30.0 40.0 ASM-2530-40
16.0 22.0 12.0 ASM-1622-12 25.0 32.0 20.0 ASM-2532-20
Order example: ASM-0103-02 – no minimum order quantity. 16.0 22.0 15.0 ASM-1622-15 25.0 +0.065 32.0 30.0 ASM-2532-30
A200 iglidur® material S Cylindrical M Metric 01 Inner Ø d1 03 Outer Ø d2 02 Total length b1 16.0 22.0 16.0 ASM-1622-16 25.0 +0.195 32.0 40.0 ASM-2532-40
16.0 22.0 20.0 ASM-1622-20 26.0 30.0 20.0 ASM-2630-20
16.0 22.0 25.0 ASM-1622-25 26.0 32.0 30.0 ASM-2632-30
d1 d1 d2 b1 Part No. d1 d1 d2 b1 Part No. 18.0 24.0 12.0 ASM-1824-12 27.0 34.0 20.0 ASM-2734-20
Tolerance3) h13 Tolerance3) h13 18.0 24.0 20.0 ASM-1824-20 27.0 34.0 30.0 ASM-2734-30
[mm] [mm] [mm] [mm] [mm] [mm] 18.0 24.0 30.0 ASM-1824-30 27.0 34.0 40.0 ASM-2734-40
1.0 3.0 2.0 ASM-0103-02 8.0 10.0 10.0 ASM-0810-10 20.0 23.0 15.0 ASM-2023-15 28.0 33.0 20.0 ASM-2833-20
1.5 4.0 2.0 ASM-0104-02 8.0 11.0 8.0 ASM-0811-08 20.0 23.0 20.0 ASM-2023-20 28.0 36.0 20.0 ASM-2836-20
2.0 5.0 2.0 ASM-0205-02 8.0 11.0 12.0 ASM-0811-12 20.0 25.0 15.0 ASM-2025-15 28.0 36.0 30.0 ASM-2836-30
2.0 5.0 3.0 ASM-0205-03 8.0 12.0 6.0 ASM-0812-06 20.0 25.0 20.0 ASM-2025-20 28.0 36.0 40.0 ASM-2836-40
+0.020
2.5 6.0 3.0 ASM-0206-03 8.0 12.0 8.0 ASM-0812-08 20.0 +0.065 25.0 30.0 ASM-2025-30 30.0 38.0 20.0 ASM-3038-20
+0.080
3.0 5.0 3.0 ASM-0305-03 8.0 12.0 10.0 ASM-0812-10 20.0 +0.195 26.0 15.0 ASM-2026-15 30.0 38.0 30.0 ASM-3038-30
3.0 5.0 4.0 ASM-0305-04 8.0 12.0 12.0 ASM-0812-12 20.0 26.0 20.0 ASM-2026-20 30.0 38.0 40.0 ASM-3038-40
3.0 6.0 3.0 ASM-0306-03 8.0 14.0 6.0 ASM-0814-06 20.0 26.0 30.0 ASM-2026-30 32.0 40.0 20.0 ASM-3240-20
+0.080
3.0 6.0 4.0 ASM-0306-04 8.0 +0.040 14.0 10.0 ASM-0814-10 22.0 26.0 15.0 ASM-2226-15 32.0 40.0 30.0 ASM-3240-30
+0.240
4.0 7.0 3.0 ASM-0407-03 9.0 +0.130 12.0 14.0 ASM-0912-14 22.0 28.0 10.0 ASM-2228-10 32.0 40.0 40.0 ASM-3240-40
4.0 7.0 4.0 ASM-0407-04 10.0 12.0 10.0 ASM-1012-10 3)
After press-fit. Testing methods, page 61
4.0 7.0 6.0 ASM-0407-06 10.0 14.0 6.0 ASM-1014-06
4.0 8.0 6.0 ASM-0408-06 10.0 14.0 8.0 ASM-1014-08
5.0 8.0 4.0 ASM-0508-04 10.0 14.0 10.0 ASM-1014-10
5.0 8.0 5.0 ASM-0508-05 10.0 14.0 16.0 ASM-1014-16
5.0 8.0 8.0 ASM-0508-08 10.0 16.0 6.0 ASM-1016-06
5.0 +0.030 9.0 5.0 ASM-0509-05 10.0 16.0 10.0 ASM-1016-10
5.0 +0.105 9.0 8.0 ASM-0509-08 10.0 16.0 16.0 ASM-1016-16
6.0 8.0 10.0 ASM-0608-10 12.0 14.0 20.0 ASM-1214-20 Available from stock Ordering note
6.0 9.0 6.0 ASM-0609-06 12.0 16.0 15.0 ASM-1216-15 Detailed information about delivery time online. Our prices are scaled according to order
6.0 10.0 4.0 ASM-0610-04 12.0 16.0 20.0 ASM-1216-20 www.igus.eu/24 quantities, current prices can be found online.
6.0 10.0 6.0 ASM-0610-06 12.0 18.0 8.0 ASM-1218-08 Order online
6.0 10.0 10.0 ASM-0610-10 12.0 18.0 10.0 ASM-1218-10 Discount scaling
+0.050 including delivery times, prices, online tools
6.0 12.0 6.0 ASM-0612-06 12.0 18.0 15.0 ASM-1218-15 1-9 50-99 500-999
+0.160 www.igus.eu/A200
6.0 12.0 10.0 ASM-0612-10 12.0 18.0 20.0 ASM-1218-20 10-24 100-199 1,000-2,499
7.0 10.0 5.0 ASM-0710-05 14.0 16.0 10.0 ASM-1416-10 25-49 200-499 2,500-4,999
7.0 +0.040 10.0 8.0 ASM-0710-08 14.0 16.0 15.0 ASM-1416-15 No minimum order value.
8.0 +0.130 10.0 6.0 ASM-0810-06 14.0 16.0 20.0 ASM-1416-20 No low-quantity surcharges.
8.0 10.0 8.0 ASM-0810-08 14.0 20.0 10.0 ASM-1420-10 Free shipping within Germany for orders
EN 09/2023
EN 09/2023
3)
After press-fit. Testing methods, page 61 above €150.
438 3D-CAD, finder and service life calculation ... www.igus.eu/A200 Lubrication-free made easy ... from stock ... no minimum order quantity 439
iglidur® A200 iglidur® A200
+80°C +80°C
18MPa 18MPa
Bearing technology | Plain bearings | iglidur® A200 Product range
Flange bearings (form F) d1 d1 d2 d3 b1 b2 Part No. d1 d1 d2 d3 b1 b2 Part No.
.5
.0 Tolerance3) d133) h13 h13 Tolerance3) d133) h13 h13
ax
f1
30
m
r
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm]
°
22.0 28.0 34.0 15.0 3.00 AFM-2228-15 27.0 34.0 40.0 40.0 4.00 AFM-2734-40
22.0 28.0 34.0 20.0 3.00 AFM-2228-20 28.0 36.0 42.0 20.0 4.00 AFM-2836-20
d2
d3
d1
22.0 28.0 34.0 30.0 3.00 AFM-2228-30 28.0 36.0 42.0 30.0 4.00 AFM-2836-30
+0.065
24.0 30.0 36.0 15.0 3.00 AFM-2430-15 28.0 36.0 42.0 40.0 4.00 AFM-2836-40
+0.195
b2 24.0 30.0 36.0 20.0 3.00 AFM-2430-20 30.0 38.0 44.0 20.0 4.00 AFM-3038-20
+0.065
b1 24.0 30.0 36.0 30.0 3.00 AFM-2430-30 30.0 38.0 44.0 30.0 4.00 AFM-3038-30
+0.195
25.0 32.0 38.0 20.0 4.00 AFM-2532-20 30.0 38.0 44.0 40.0 4.00 AFM-3038-40
2)
Thickness < 0.6mm: chamfer = 20° 25.0 32.0 38.0 30.0 4.00 AFM-2532-30 32.0 40.0 46.0 20.0 4.00 AFM-3240-20
+0.080
Chamfer in relation to d1 25.0 32.0 38.0 40.0 4.00 AFM-2532-40 32.0 40.0 46.0 30.0 4.00 AFM-3240-30
+0.240
d1 [mm] Ø 1-6 Ø 6-12 Ø 12-30 Ø > 30 Dimensions according to ISO 2795 and special 27.0 34.0 40.0 20.0 4.00 AFM-2734-20 32.0 40.0 46.0 40.0 4.00 AFM-3240-40
f1 [mm] 0.3 0.5 0.8 1.2 dimensions 27.0 34.0 40.0 30.0 4.00 AFM-2734-30
3)
After press-fit. Testing methods, page 61
Order example: AFM-0103-02 – no minimum order quantity.
A200 iglidur® material F With flange M Metric 01 Inner Ø d1 03 Outer Ø d2 02 Total length b1
EN 09/2023
3)
After press-fit. Testing methods, page 61
above €150.
440 3D-CAD, finder and service life calculation ... www.igus.eu/A200 Lubrication-free made easy ... from stock ... no minimum order quantity 441
Food bearing with media resistance
up to +90°C
Compliant with Regulation (EU) No.
10/2011 and FDA guidelines
iglidur A160 ®
EN 09/2023
iglidur® A160 iglidur® A160
+90°C +90°C
15MPa 15MPa
Bearing technology | Plain bearings | iglidur® A160 Technical data
General properties Testing method
Bar stock,
+90°C Compressive strength MPa 37
Max. permissible surface pressure (+20°C) MPa 14
round bar
Page 743 Compliant with Regulation (EU) No. 10/2011 Shore D hardness 60 DIN 53505
and FDA guidelines Physical and thermal properties
Max. application temperature long-term °C +90
FOOD
iglidur® A160 offers maximum media resistance in the medium temperature range and is therefore a true Max. application temperature short-term °C +100
low-cost iglidur®. The profile of properties is completed by the suitability for applications in the food industry. Min. application temperature °C -50
Bar stock, ● Compliant with Regulation (EU) No. 10/2011 Thermal conductivity W/m · K 0.30 ASTM C 177
plate
Page 773 ● FDA-compliant Coefficient of thermal expansion (at +23°C) K-1 · 10-5 11 DIN 53752
● High media resistance Electrical properties
● Cost-effective Specific transitional resistance Ωcm > 1012 DIN IEC 93
● Lubrication-free Surface resistance Ω > 1012 DIN 53482
● Maintenance-free Table 01: Material properties
tribo-tape liner
Page 781
Typical application areas iglidur ® A160 plain bearings are characterised by Resistance to weathering
● Food industry extreme media resistance at a low cost. Tribologically iglidur® A160 plain bearings are continuously resistant
● Beverage technology optimised, the material can be used in temperatures to weathering. The material properties are only slightly
● Medical technology up to +90°C and also conforms to demands of the affected. Possible discolourations are only superficial.
food processing sector. The profile of properties is
completed by the "optical detectability", i.e. the blue colour, Mechanical properties
Guide rings
Page 641 often required in the industry. When temperatures increase, the compressive strength of
iglidur® A160 plain bearings decreases. Diagram 02 shows
Descriptive technical specifications Moisture absorption this inverse relationship. The maximum recommended
Wear resistance at +23°C – + The moisture absorption of iglidur® A160 plain bearings surface pressure is a mechanical material parameter. No
in ambient conditions is approximately 0.1% weight. The conclusions regarding the tribological properties can be
Wear resistance at +90°C – +
saturation limit submerged in water is also approximately drawn from this.
Two hole Wear resistance at +150°C – + 0.1% weight. Diagram 03 shows the elastic deformation of iglidur® A160
flange
bearings under different loads. Plastic deformation is minimal up to
Page 667 Slide property – +
Vacuum a radial load of 15MPa. However, it is also dependent on
Wear resistance under water – + In vacuum, any present moisture is released as vapour. Use the service time.
in vacuum is only possible with dehumidified iglidur® A160 Surface pressure, page 45
Media resistance – +
bearings.
Moulded Resistant to edge pressures – +
special parts
Page 696 Radiation resistance
Resistant to shock and impact loads – +
Plain bearings made from iglidur® A160 are resistant up to
Dirt resistance – + a radiation intensity of 1 · 10⁵ Gy.
EN 09/2023
spherical balls
Page 993 www.igus.eu/iglidur-finder www.igus.eu/iglidur-expert
444 3D-CAD, finder and service life calculation ... www.igus.eu/A160 Lubrication-free made easy ... from stock ... no minimum order quantity 445
iglidur® A160 iglidur® A160
+90°C +90°C
15MPa 15MPa
Bearing technology | Plain bearings | iglidur® A160 Technical data
Permissible surface speeds 100.0 0.3
Chemicals Resistance
iglidur® A160 was developed for low surface speeds. Alcohols + 10.0
Cf53 steel
Dry Greases Oil Water
Wear [µm/km]
Coefficient of friction and wear resistance are dependent 5 0.5
Coefficient of friction μ 0.09-0.19 0.08 0.03 0.04
Load [MPa]
on the application parameters (diagrams 04 and 05). For
Table 04: Coefficient of friction against steel (Ra = 1μm,
iglidur® A160 plain bearings, altering the coefficient of 0 0.0
50HRC)
friction µ as a function of surface speed has less effect. 20 30 40 50 60 70 80 90
The coefficient of friction decreases with increasing load. Temperature [°C]
Housing Plain bearings Shaft
Surface finishes (Ra) of the shaft between 0.6-0.7µm are Diagram 02: Maximum recommended surface pressure as a Diagram 06: Wear, rotating with different shaft materials,
Ø d1 [mm] H7 [mm] E10 [mm] h9 [mm]
ideal. function of temperature (15MPa at +20°C) pressure, p = 1MPa, v = 0.3m/s
0-3 +0.000 +0.010 +0.014 +0.054 -0.025 +0.000
Coefficient of friction and surfaces, page 51
> 3-6 +0.000 +0.012 +0.020 +0.068 -0.030 +0.000
Wear resistance, page 54 12 160
> 6-10 +0.000 +0.015 +0.025 +0.083 -0.036 +0.000
rotating
> 10-18 +0.000 +0.018 +0.032 +0.102 -0.043 +0.000 10 oscillating
Shaft materials ■ +23°C ■ +60°C 120
> 18-30 +0.000 +0.021 +0.040 +0.124 -0.052 +0.000 8
Diagram 06 shows results of testing different shaft materials
> 30-50 +0.000 +0.025 +0.050 +0.150 -0.062 +0.000 6 80
with plain bearings made from iglidur® A160. For rotational
Deformation [%]
> 50-80 +0.000 +0.030 +0.060 +0.180 -0.074 +0.000
Wear [µm/km]
applications with low loads, the most interesting, media 4
> 80-120 +0.000 +0.035 +0.072 +0.212 -0.087 +0.000 40
and corrosion-resistant shaft materials 304 stainless steel, 2
> 120-180 +0.000 +0.040 +0.085 +0.245 -0.100 +0.000
high grade steel and hard-chromed steel reveal themselves 0 0
Table 05: Important tolerances for plain bearings according
as particularly good mating partners. On high grade steel 0 3 6 9 12 15 5 10 15 20
to ISO 3547-1 after press-fit
shafts, however, the wear increases the fastest with the Load [MPa] Load [MPa]
load (diagram 06). With Cf53 shafts, the wear in pivoting Diagram 03: Deformation under pressure and temperature Diagram 07: Wear for oscillating and rotating applications
applications is exemplary compared to rotating applications. with shaft material Cf53 hardened and ground steel, as a
In rotation the wear, as with many other iglidur® materials, function of the load
is higher than when pivoting (diagram 07). 0.6
0.4
Installation tolerances 0.3
iglidur® A160 plain bearings are standard bearings for 0.2
shafts with h-tolerance (recommended minimum h9). The
0.1
bearings are designed for press-fit into a housing machined
0.0
to a H7 tolerance. After being assembled into a nominal
0.1 0.2 0.3 0.4 0.5
size housing, the inner diameter automatically adjusts to
Surface speed [m/s]
the E10 tolerances.
Diagram 04: Coefficient of friction as a function of the
Testing methods, page 61
EN 09/2023
EN 09/2023
446 3D-CAD, finder and service life calculation ... www.igus.eu/A160 Lubrication-free made easy ... from stock ... no minimum order quantity 447
iglidur® A160 iglidur® A160
+90°C +90°C
15MPa 15MPa
Bearing technology | Plain bearings | iglidur® A160 Bearing technology | Plain bearings | iglidur® A160
Sleeve bearings (form S) Flange bearings (form F)
.5
.0
ax
f1
30
f1
rm
°
30°
d2
d3
d1
d1
d2
0.5
30°
b1 b2
b1
2)
Thickness < 0.6mm: chamfer = 20° 2)
Thickness < 0.6mm: chamfer = 20°
Chamfer in relation to d1 Chamfer in relation to d1
d1 [mm] Ø 6-12 Ø 12-30 Dimensions according to ISO 3547-1 and d1 [mm] Ø 6-12 Ø 12-30 Dimensions according to ISO 3547-1 and
f1 [mm] 0.5 0.8 special dimensions f1 [mm] 0.5 0.8 special dimensions
Order example: A160SM-0608-06 – no minimum order quantity. Order example: A160FM-0608-06 – no minimum order quantity.
A160 iglidur® material S Cylindrical M Metric 06 Inner Ø d1 08 Outer Ø d2 06 Total length b1 A160 iglidur® material F With flange M Metric 06 Inner Ø d1 08 Outer Ø d2 06 Total length b1
Available from stock Ordering note Available from stock Ordering note
Detailed information about delivery time online. Our prices are scaled according to order Detailed information about delivery time online. Our prices are scaled according to order
www.igus.eu/24 quantities, current prices can be found online. www.igus.eu/24 quantities, current prices can be found online.
EN 09/2023
448 3D-CAD, finder and service life calculation ... www.igus.eu/A160 Lubrication-free made easy ... from stock ... no minimum order quantity 449
Suitable for contact with drinking water
KTW-compliant
iglidur UW160 ®
● When a recurring media-resistant plain bearing with intermittent dry operation is required
iglidur® A160
● When a media and temperature-resistant universal plain bearing is required
iglidur® X
● When a standard plain bearing is required for use in a moist environment
iglidur® P
EN 09/2023
EN 09/2023
iglidur® iglidur®
UW160 UW160
+90°C +90°C
15MPa 15MPa
Bearing technology | Plain bearings | iglidur® UW160 Technical data
General properties Testing method
Bar stock,
KTW-compliant Compressive strength MPa 32
round bar Max. permissible surface pressure (+20°C) MPa 20
Page 743 Shore D hardness 60 DIN 53505
iglidur® UW160 is tribologically optimised for continuous operation in liquid media. Its superior media
resistance not only permits uses with potable water contact. Physical and thermal properties
● Suitable for applications in liquids Max. application temperature long-term °C +90
FOOD
● Suitable for contact with drinking water (KTW-compliant) Max. application temperature short-term °C +100
● High media resistance Min. application temperature °C -50
Bar stock, ● Lubrication-free Thermal conductivity W/m · K 0.50 ASTM C 177
plate
Page 773 ● Maintenance-free Coefficient of thermal expansion (at +23°C) K-1 · 10-5 18 DIN 53752
Electrical properties
Typical application areas Specific transitional resistance Ωcm > 1012 DIN IEC 93
● Fluid technology Surface resistance Ω > 1012 DIN 53482
● Pumps Table 01: Material properties
tribo-tape liner ● Water meters
Page 781
iglidur® UW160 was developed quite specifically with Resistance to weathering
regard to maximum wear resistance in media-based iglidur® UW160 plain bearings are continuously resistant
continuous operation. In such applications, low radial loads to weathering. The material properties are only slightly
and medium temperatures usually occur. The suitability affected. Possible discolourations are only superficial.
for contact with drinking water and very good durability
complete the profile of properties. Mechanical properties
Guide rings
Page 641 When temperatures increase, the compressive strength
Moisture absorption of iglidur® UW160 plain bearings decreases. Diagram
Descriptive technical specifications The moisture absorption of iglidur® UW160 plain bearings 02 shows this inverse relationship. The maximum
Wear resistance at +23°C – + in ambient conditions is approximately 0.1% weight. The recommended surface pressure is a mechanical material
saturation limit submerged in water is 0.1% weight. parameter. No conclusions regarding the tribological
Wear resistance at +90°C – +
properties can be drawn from this.
Two hole Wear resistance at +150°C – + Vacuum Diagram 03 shows the elastic deformation of iglidur® UW160
flange
bearings In vacuum, any present moisture is released as vapour. under different loads.
Page 667 Slide property – +
Use in vacuum is only possible with dehumidified Surface pressure, page 45
Wear resistance under water – + iglidur® UW160 bearings.
Media resistance – +
Radiation resistance
Moulded Resistant to edge pressures – + Plain bearings made from iglidur® UW160 are resistant up
special parts
Page 696 to a radiation intensity of 3 · 10² Gy.
Resistant to shock and impact loads – +
Dirt resistance – +
EN 09/2023
spherical balls
Page 993 www.igus.eu/iglidur-finder www.igus.eu/iglidur-expert
452 3D-CAD, finder and service life calculation ... www.igus.eu/UW160 Lubrication-free made easy ... from stock ... no minimum order quantity 453
iglidur® iglidur®
UW160 UW160
+90°C +90°C
15MPa 15MPa
Bearing technology | Plain bearings | iglidur® UW160 Technical data
Permissible surface speeds Installation tolerances 100.0 0.3
The maximum recommended surface speed is based on iglidur® UW160 plain bearings are standard bearings for
10.0
H.a. aluminium
10
an influence on the wear. The wear rises with increasing Strong alkalines +
6
Cf53 steel
Wear [µm/km]
temperatures. For temperatures over +70°C an additional All data given at room temperature [+20°C]
5
Load [MPa]
3
securing is required. Table 02: Chemical resistance
Application temperatures, page 53 Chemical table, page 1170 0 0
Additional securing, page 53 20 30 40 50 60 70 80 90
Rotating Oscillating linear Temperature [°C]
Friction and wear Long-term m/s 0.3 0.3 1.0 Diagram 02: Maximum recommended surface pressure as a Diagram 06: Wear, rotating with different shaft materials,
Similar to wear resistance, the coefficient of friction µ also Short-term m/s 0.5 0.4 2.5 function of temperature (15MPa at +20°C) pressure, p = 1MPa, v = 0.3m/s
changes with the surface speed and load (diagram 04 and Table 03: Maximum surface speeds
05). The influence of surface speed and surface finish of the 10 160
shaft on the friction coefficient is low, but with increasing Dry Greases Oil Water rotating
8 oscillating
radial load the coefficient of friction decreases significantly, Coefficient of friction μ 0.17-0.31 0.08 0.03 0.03 +23°C 120
mainly in the range of up to 7.5MPa. Table 04: Coefficient of friction against steel (Ra = 1μm, 6 +60°C
80
Coefficient of friction and surfaces, page 51 50HRC)
Deformation [%]
4
Wear [µm/km]
Wear resistance, page 54 40
Housing Plain bearings Shaft 2
iglidur® materials for dry operation. As with many other > 50-80 +0.000 +0.030 +0.060 +0.180 -0.074 +0.000 0.5
Coefficient of friction [µ]
iglidur® materials in dry operation, diagram 07 shows the > 80-120 +0.000 +0.035 +0.072 +0.212 -0.087 +0.000 0.4
significantly higher wear in rotation than in pivoting with > 120-180 +0.000 +0.040 +0.085 +0.245 -0.100 +0.000 0.3
otherwise identical parameters. Table 05: Important tolerances for plain bearings according 0.2
Shaft materials, page 56 to ISO 3547-1 after press-fit
0.1
0.0
0.1 0.2 0.3 0.4 0.5
Surface speed [m/s]
Diagram 04: Coefficient of friction as a function of the
EN 09/2023
EN 09/2023
454 3D-CAD, finder and service life calculation ... www.igus.eu/UW160 Lubrication-free made easy ... from stock ... no minimum order quantity 455
iglidur® iglidur®
UW160 UW160
+90°C +90°C
15MPa 15MPa
Bearing technology | Plain bearings | iglidur® UW160 Bearing technology | Plain bearings | iglidur® UW160
Sleeve bearings (form S) Flange bearings (form F)
.5
.0
ax
f1
30
f1
rm
°
30°
d2
d3
d1
d1
d2
0.5
30°
b1 b2
b1
2)
Thickness < 0.6mm: chamfer = 20° 2)
Thickness < 0.6mm: chamfer = 20°
Chamfer in relation to d1 Chamfer in relation to d1
d1 [mm] Ø 1-6 Ø 6-12 Dimensions according to ISO 3547-1 and d1 [mm] Ø 1-6 Ø 6-12 Dimensions according to ISO 3547-1 and
f1 [mm] 0.3 0.5 special dimensions f1 [mm] 0.3 0.5 special dimensions
Order example: UW160SM-0304-03 – no minimum order quantity. Order example: UW160FM-0304-05 – no minimum order quantity.
UW160 iglidur® material S Cylindrical M Metric 03 Inner Ø d1 04 Outer Ø d2 03 Total length b1 UW160 iglidur® material F With flange M Metric 03 Inner Ø d1 04 Outer Ø d2 05 Total length b1
Available from stock Ordering note Available from stock Ordering note
Detailed information about delivery time online. Our prices are scaled according to order Detailed information about delivery time online. Our prices are scaled according to order
www.igus.eu/24 quantities, current prices can be found online. www.igus.eu/24 quantities, current prices can be found online.
EN 09/2023
456 3D-CAD, finder and service life calculation ... www.igus.eu/UW160 Lubrication-free made easy ... from stock ... no minimum order quantity 457
For the tobacco industry
FDA-compliant
iglidur T220 ®
EN 09/2023
iglidur® T220 iglidur® T220
+100°C +100°C
40MPa 40MPa
Bearing technology | Plain bearings | iglidur® T220 Technical data
General properties Testing method
Bar stock,
FDA-compliant Compressive strength MPa 55
round bar Max. permissible surface pressure (+20°C) MPa 40
Page 743 Shore D hardness 76 DIN 53505
Plain bearings that constitute only materials "recommended" for the tobacco industry. They are free from
carcinogenic additives like, for instance, PTFE. Physical and thermal properties
● Free from banned ingredients as requested by main manufacturers of tobacco products Max. application temperature long-term °C +100
FOOD
● FDA-compliant Max. application temperature short-term °C +160
● Lubrication-free Min. application temperature °C -40
Bar stock, ● Maintenance-free Thermal conductivity W/m · K 0.24 ASTM C 177
plate
Page 773 Coefficient of thermal expansion (at +23°C) K-1 · 10-5 11 DIN 53752
Typical application areas Electrical properties
● Tobacco industry Specific transitional resistance Ωcm > 1010 DIN IEC 93
Surface resistance Ω > 1010 DIN 53482
Table 01: Material properties
tribo-tape liner
Page 781
iglidur® T220 is a special material for applications in the Resistance to weathering
tobacco processing industry. It fulfils the demands of the iglidur® T220 plain bearings are resistant to weathering.
tobacco industry (engineering database). The material is The material properties are slightly affected. Discolouration
free of undesirable or banned ingredients, as requested occurs.
by reputed manufacturers from 2004 onward.
Mechanical properties
Guide rings
Page 641 Moisture absorption With increasing temperatures, the compressive strength of
The humidity absorption of iglidur® T220 bearings amounts iglidur® T220 plain bearings decreases. Diagram 02 shows
Descriptive technical specifications to about 0.3% weight in standard climatic conditions. this inverse relationship. The maximum recommended
Wear resistance at +23°C – + The saturation limit submerged in water is 0.5% weight. surface pressure is a mechanical material parameter. No
These values are so low that consideration of expansion conclusions regarding the tribological properties can be
Wear resistance at +90°C – +
by moisture absorption is only required under extreme drawn from this.
Two hole Wear resistance at +150°C – + circumstances. iglidur® T220 plain bearings can be stressed up to the
flange
bearings permitted limit of 40MPa, the elastic deformation is less
Page 667 Slide property – +
Vacuum than 2% at room temperature. The permitted load is limited
Wear resistance under water – + In vacuum, any present moisture is released as vapour. Use by higher temperatures (diagram 03).
in vacuum is only possible with dehumidified iglidur® T220 Surface pressure, page 45
Media resistance – +
bearings.
Moulded Resistant to edge pressures – +
special parts
Page 696 Radiation resistance
Resistant to shock and impact loads – +
Plain bearings made from iglidur® T220 are resistant up to
Dirt resistance – + a radiation intensity of 3 · 10² Gy.
EN 09/2023
spherical balls
Page 993 www.igus.eu/iglidur-finder www.igus.eu/iglidur-expert
460 3D-CAD, finder and service life calculation ... www.igus.eu/T220 Lubrication-free made easy ... from stock ... no minimum order quantity 461
iglidur® T220 iglidur® T220
+100°C +100°C
40MPa 40MPa
Bearing technology | Plain bearings | iglidur® T220 Technical data
Permissible surface speeds 100.0 0,7
Chemicals Resistance
0,6
The maximum speeds of iglidur ® T220 plain bearings Alcohols + 10.0
H.a. aluminium
4.0
60
specifications, the coefficient of friction and wear of 3.0
Dry Greases Oil Water
Cf53 steel
Wear [µm/km]
iglidur® T220 plain bearings remain behind those of the 40
2.0
Coefficient of friction μ 0.20-0.32 0.09 0.04 0.04
Load [MPa]
best iglidur® plain bearings. The coefficient of friction 20 1.0
Table 04: Coefficient of friction against steel (Ra = 1μm,
decreases with the load and increases only slightly with 0 0.0
50HRC)
higher speeds. 20 30 40 50 60 70 80 90 100
Coefficient of friction and surfaces, page 51 Temperature [°C]
Housing Plain bearings Shaft
Wear resistance, page 54 Diagram 02: Maximum recommended surface pressure as a Diagram 06: Wear, rotating with different shaft materials,
Ø d1 [mm] H7 [mm] E10 [mm] h9 [mm]
function of temperature (40MPa at +20°C) pressure, p = 1MPa, v = 0.3m/s
0-3 +0.000 +0.010 +0.014 +0.054 -0.025 +0.000
Shaft materials
> 3-6 +0.000 +0.012 +0.020 +0.068 -0.030 +0.000
Diagram 06 shows a summary of the results of tests with 12.8 100
> 6-10 +0.000 +0.015 +0.025 +0.083 -0.036 +0.000
different shaft materials executed with plain bearings made rotating
> 10-18 +0.000 +0.018 +0.032 +0.102 -0.043 +0.000 10.0 80
of iglidur® T220. Diagram 07 shows that the bearings react oscillating
> 18-30 +0.000 +0.021 +0.040 +0.124 -0.052 +0.000 +23°C
with a heavy increase in wear when the load is increased. +60°C 60
> 30-50 +0.000 +0.025 +0.050 +0.150 -0.062 +0.000 5.0
Therefore care should be taken to maintain the loads under
Deformation [%]
> 50-80 +0.000 +0.030 +0.060 +0.180 -0.074 +0.000 40
Wear [µm/km]
5MPa through adequate dimensioning of the bearing. 2.1
> 80-120 +0.000 +0.035 +0.072 +0.212 -0.087 +0.000 20
Shaft materials, page 56
> 120-180 +0.000 +0.040 +0.085 +0.245 -0.100 +0.000
0.0 0
Table 05: Important tolerances for plain bearings according
Installation tolerances 0 15 30 45 0 1 2 3 4 5 6
to ISO 3547-1 after press-fit
iglidur® T220 plain bearings are standard bearings for Load [MPa] Load [MPa]
shafts with h tolerance (recommended minimum h9). The Diagram 03: Deformation under pressure and temperature Diagram 07: Wear for oscillating and rotating applications
bearings are designed for press-fit into a housing machined with shaft material Cf53 hardened and ground steel, as a
to a H7 tolerance. After being assembled into a nominal function of the load
size housing, the inner diameter automatically adjusts to 0.5
EN 09/2023
462 3D-CAD, finder and service life calculation ... www.igus.eu/T220 Lubrication-free made easy ... from stock ... no minimum order quantity 463
Conductive and resistant
ESD material for high temperatures
and food contact
iglidur AX500 ®
EN 09/2023
iglidur® iglidur®
AX500 AX500
+250°C +250°C
69MPa 69MPa
Bearing technology | Plain bearings | iglidur® AX500 Technical data
General properties Testing method
Bar stock,
ESD material for high temperatures and food Compressive strength MPa n.s.
Max. permissible surface pressure (+20°C) MPa 69
round bar
Page 743 contact Shore D hardness 81 DIN 53505
Physical and thermal properties
iglidur® AX500 is a further development of iglidur® A500, a long-term endurance material. The special Max. application temperature long-term °C +250
feature of AX500 is that it is a conductive material. In addition, AX500 has an even lower coefficient of FOOD
Max. application temperature short-term °C +300
wear than its predecessor. The material was specially developed for the food industry and can therefore Min. application temperature °C up to -100
Bar stock, be used in contact with food products. Thermal conductivity W/m · K 0.26 ASTM C 177
plate ● Compliant with EU Regulation 10/2011 EC
Page 773 Coefficient of thermal expansion (at +23°C) K-1 · 10-5 9 DIN 53752
● Temperature-resistant from -100°C to +250°C Electrical properties
● Chemical-resistant Specific transitional resistance Ωcm n.s. DIN IEC 93
● Lubrication and maintenance-free Surface resistance Ω 105 - 1011 DIN 53482
● Standard range from stock
Table 01: Material properties
tribo-tape liner
Page 781 Typical application areas
iglidur® AX500 is a member of the family of extremely Resistance to weathering
● Beverage industry
media and temperature-resistant iglidur® materials X, X6 iglidur® AX500 plain bearings are resistant to weathering
● Food industry
and A500. This material is characterised by improved wear The material properties are slightly affected. Discolouration
● Medical technology
resistance and increased design freedom. occurs.
Dirt resistance – +
EN 09/2023
spherical balls
Page 993 www.igus.eu/iglidur-finder www.igus.eu/iglidur-expert
466 3D-CAD, finder and service life calculation ... www.igus.eu/AX500 Lubrication-free made easy ... from stock ... no minimum order quantity 467
iglidur® iglidur®
AX500 AX500
+250°C +250°C
69MPa 69MPa
Bearing technology | Plain bearings | iglidur® AX500 Technical data
Permissible surface speeds Installation tolerances 1,000 0.35
0.30
The maximum recommended surface speed is based on iglidur® AX500 plain bearings are standard bearings for
100
Temperature Chemicals Resistance Diagram 01: Permissible pv values for AX500 plain bearings Diagram 05: Coefficient of friction as a function of the
iglidur® AX500 belongs to the most temperature resistant Alcohols + with a wall thickness of 1mm, dry operation against a steel pressure, v = 0.01m/s
iglidur® materials. As in the case of all thermoplastics, the Diluted acids + shaft, at +20°C, mounted in a steel housing
compressive strength of iglidur® AX500 bearings decreases Diluted alkalines +
when temperatures rise. The temperatures prevailing in the Fuels + 40 6
bearing system also have an influence on the wear. The Greases, oils without additives + 35 5
H.a. aluminium
20 3
Application temperatures, page 53 Strong alkalines +
Cf53 steel
15
Wear [µm/km]
Additional securing, page 53 All data given at room temperature [+20°C] 2
10
Load [MPa]
Table 02: Chemical resistance 5 1
Friction and wear Chemical table, page 1170 0 0
The coefficient of friction and wear in iglidur® AX500 20 50 80 120 150 200
are more favourable than in the other high temperature Rotating Oscillating linear Temperature [°C]
materials iglidur® X and A500. The coefficient of friction Long-term m/s 1.0 0.4 2.0 Diagram 02: Maximum recommended surface pressure as a Diagram 06: Wear, rotating with different shaft materials,
increases moderately as the sliding speed increases. The Short-term m/s 1.5 0.6 3.0 function of temperature (80MPa at +20°C) pressure, p = 1MPa, v = 0.3m/s
coefficient of friction initially drops rapidly to less than 0.1 Table 03: Maximum surface speeds
under loads of up to approximately 20MPa, and then only 10 200
marginally increases as loads continue to increase. The Dry Greases Oil Water 180 rotating
8 160 oscillating
friction and wear are also dependent, to a large degree, Coefficient of friction μ 0.08-0.22 0.09 0.04 0.04 +23°C 140
on the mating partner. Shafts that are too smooth increase Table 04: Coefficient of friction against steel (Ra = 1μm, 6 +60°C 120
100
both the coefficient of friction and the wear of the bearing. 50HRC)
Deformation [%]
4 80
Wear [µm/km]
Ground surfaces with an average surface finish Ra of 0.6 60
Housing Plain bearings Shaft 2 40
to 0.8µm are ideal. 20
Coefficient of friction and surfaces, page 51 Ø d1 [mm] H7 [mm] F10 [mm] h9 [mm] 0 0
Wear resistance, page 54 0-3 +0.000 +0.010 +0.006 +0.046 -0.025 +0.000 0 25 50 75 100 120 0 5 10 15 20 25 30 35 40 45
> 3-6 +0.000 +0.012 +0.010 +0.058 -0.030 +0.000 Load [MPa] Load [MPa]
Shaft materials > 6-10 +0.000 +0.015 +0.013 +0.071 -0.036 +0.000 Diagram 03: Deformation under pressure and temperature Diagram 07: Wear for oscillating and rotating applications
Diagram 06 shows a summary of the results of tests with > 10-18 +0.000 +0.018 +0.016 +0.086 -0.043 +0.000 with shaft material Cf53 hardened and ground steel, as a
different shaft materials executed with plain bearings made > 18-30 +0.000 +0.021 +0.020 +0.104 -0.052 +0.000 function of the load
of iglidur® AX500. Using the example of a rotating motion > 30-50 +0.000 +0.025 +0.025 +0.125 -0.062 +0.000 0.30
at 1MPa and a speed of 0.3m/s, it becomes apparent that > 50-80 +0.000 +0.030 +0.030 +0.150 -0.074 +0.000 0.25
Coefficient of friction [µ]
iglidur® AX500 has consistent wear characteristics across > 80-120 +0.000 +0.035 -0.036 +0.176 -0.087 +0.000 0.20
a variety of shaft types. This wear rate spikes in combination > 120-180 +0.000 +0.040 +0.043 +0.203 +0.000 +0.100 0.15
with free cutting steel, and, notably so, reduces in Table 05: Important tolerances for plain bearings according 0.10
combination with HC aluminium. The wear under rotational to ISO 3547-1 after press-fit
0.05
loads is higher, specifically with increasing radial loads as
0.00
compared to pivoting movements (diagram 07).
0.10 0.30 0.50 0.70 0.90 1.10 1.30
Shaft materials, page 56
Surface speed [m/s]
Diagram 04: Coefficient of friction as a function of the
EN 09/2023
EN 09/2023
468 3D-CAD, finder and service life calculation ... www.igus.eu/AX500 Lubrication-free made easy ... from stock ... no minimum order quantity 469
iglidur® iglidur®
AX500 AX500
+250°C +250°C
69MPa 69MPa
Bearing technology | Plain bearings | iglidur® AX500 Bearing technology | Plain bearings | iglidur® AX500
Sleeve bearings (form S) Flange bearings (form F)
.5
.0
ax
f1
30
f1
rm
°
30°
d2
d3
d1
d1
d2
0.5
30°
b1 b2
b1
2)
Thickness < 0.6mm: chamfer = 20° 2)
Thickness < 0.6mm: chamfer = 20°
Chamfer in relation to d1 Chamfer in relation to d1
d1 [mm] Ø 1-6 Ø 6-12 Ø 12-30 Ø > 30 Dimensions according to ISO 3547-1 and d1 [mm] Ø 6-12 Ø 12-30 Dimensions according to ISO 3547-1 and
f1 [mm] 0.3 0.5 0.8 1.2 special dimensions f1 [mm] 0.5 0.8 special dimensions
Order example: AX500SM-0608-06 - no minimum order quantity. Order example: AX500SM-0608-06 - no minimum order quantity.
AX500 iglidur® material S Cylindrical M Metric 06 Inner Ø d1 08 Outer Ø d2 06 Total length b1 AX500 iglidur® material F With flange M Metric 06 Inner Ø d1 08 Outer Ø d2 06 Total length b1
Available from stock Ordering note Available from stock Ordering note
Detailed information about delivery time online. Our prices are scaled according to order Detailed information about delivery time online. Our prices are scaled according to order
www.igus.eu/24 quantities, current prices can be found online. www.igus.eu/24 quantities, current prices can be found online.
EN 09/2023
470 3D-CAD, finder and service life calculation ... www.igus.eu/AX500 Lubrication-free made easy ... from stock ... no minimum order quantity 471