Professional Documents
Culture Documents
R R
0920
TBS-2000
2. ATTACHING TABLE EXTENSIONS 3. FITTING THE BLADE GUARD
The table saw is supplied with 1 1. Flip the table saw upright onto its
rear table extension and 2 side table feet, raise the blade to its highest
extensions. setting and remove the table
insert by loosening the 2 screws
For ease of assembly, place the holding it down.
table saw upside down on a flat
surface with space for the table
extensions.
2. Loosen the riving knife securing
1. Align the bolt holes of the rear bolt using the supplied spanner.
extension with the back edge of Ensure the bolt does not come
the table saw. Use the bolt holes completely out as this bolt may be
and front ruler edge of the table to difficult to refit.
align the side extensions.
2. Insert a pre-assembled short bolt 3. Insert the riving knife between the
through a bolt hole in the table mounting plate and the securing 3 - 5mm
saw and extension table, place bolt so that there is a 3-5mm gap
a washer onto it and secure with between the blade and the riving
a hex nut. Repeat this for the knife. Tighten the securing bolt
other 5 bolt holes to attach the using the supplied spanner.
extensions tables.
TABLE STRUTS
TBS-2000
STANDARD EQUIPMENT
Sliding Mitre
TABLE SAW
Rip Fence
Gauge
R
R
R
R
A
A
A
2000W 254mm
A
L
R
L
L
R
L
A
Table Extensions x 3
A
L
INSTRUCTION MANUAL
L
SPECIFICATIONS
Motor: 2000W (S6 40%) 1800W (S1)
Cutting Blades x 3
Input: 230-240V ~ 50Hz
No Load Speed: 4,250/min
Blade: Ø254mm x Ø30 x 2.4mm
Blade Teeth: 24 TCT
Bevel Angle: 0º-45° left
Blade Height Adj: 0-80mm
Max. Cutting Capacity:
Bevel 90°: 80mm
Push Stick, Blade Guard & Riving
Bevel 45°: 55mm Knife
Table Size: 555 x 580mm
With Side Ext.: 855 x 580mm
Rear Extension: 390 x 185mm
Dust Port: Ø36mm
Weight: 26.0kg
Assembly Fasteners
TBS-2000
WARRANTY
IN ORDER TO MAKE A CLAIM UNDER THIS The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
WARRANTY YOU MUST RETURN THE PRODUCT
Our goods come with guarantees that cannot be excluded
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH at law. You are entitled to a replacement or refund for a major
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO failure and for compensation for any other reasonably foreseeable
RETURNING YOUR PRODUCT FOR WARRANTY loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
PLEASE TELEPHONE OUR CUSTOMER SERVICE failure does not amount to a major failure.
HELPLINE: Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
Australia 1800 069 486 any additional direct loss as a result of a defective product you
New Zealand 0508 069 486 may be able to claim such expenses by contacting our customer
service helpline above.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
0920
3
TABLE SAW
1. ADJUSTMENTS
1 Side Table Extension 9 Push Stick
2 Sliding Mitre Gauge 10 Table Insert
For detailed assembly instructions see Assembly
3 Rear Table Extension 11 ON/OFF Switch Manual.
4 Blade Guard 12 Bevel Lock WARNING! ENSURE THE TOOL IS SWITCHED OFF
AND DISCONNECTED FROM THE POWER SUPPLY
5 Rip Fence 13 Blade Height Adjustment BEFORE PERFORMING ANY OF THE FOLLOWING
Handle PROCEDURES.
6 Rip Fence Lever
14 Bevel Adjustment Dial
7 Table Strut Cutting Depth
8 Stabilising Bracket The depth should be adjusted so that no more than one tooth is
protruding through the timber. This helps to minimise splintering.
7 8
22.5°
15°
30°
22.5° 30°
15°
Bevel Angle
1 Loosen the bevel lock by
rotating anti-clockwise.
°
45
30°
22.5°
15°
9 10 11 12 13 14
°
45
30°
22.5°
15°
bevel scale.
30°
clockwise.
°
45
ONLINE MANUAL
30°
22.5°
15°
º
45
30º
25º
20º 22.5º
0º 5º 10º 15º
OPERATION
Using the Sliding Mitre Gauge WARNING! TO REDUCE THE RISK OF ELECTRICAL
The sliding mitre gauge can be fitted into 1 of the 2 grooves in the table SHOCK, THE USE OF A RESIDUAL CURRENT
and can be used to easily perform mitre angle cuts. DEVICE (RATED 30mA OR LESS) IS RECOMMENDED.
Blade Guard
3 Rotate the mitre gauge to 1 The blade guard must be
the desired angle using the able to move freely, adjust
mitre scale. if necessary (refer to
Assembly Manual).
20mm
5. MAKING A CUT
When you make a longitudinal cut, never adopt a working position that Be sure to use a push stick
is in line with the cutting direction. when making longitudinal cuts
in work pieces smaller than
1 Set the rip fence in accordance with the workpiece height and the 120mm in width. A push stick
desired width. (See Stop Height, Cutting Width). is supplied with the saw.
2 Switch on the saw by pressing the ON button "I". Replace a worn or damaged
push stick immediately.
3 lace your hands (with
P
fingers closed ensuring they
will be clear of the blade) flat
on the workpiece and push
Making Bevel Cuts
the workpiece along the rip
fence and into the blade. Bevel cuts must always be done
using the rip fence.
4 Guide at the side with your
left or right hand (depending 1 et the blade to the desired
S
on the position of the rip angle. (See Setting the Bevel
fence) only as far as the front Angle)
edge of the table. º
45
15º
20º
25º
22.5
º
30º
2 et the rip fence in accordance
S
with the workpiece width and
0º 5º 10º
0º 5º 10º 15º
6 Switch off the saw again. Do not remove the off-cut until the blade
has stopped rotating.
TBS-2000
OPERATION MAINTENANCE
PROCEDURES.
height adjustment
handle and setting WARNING! USE ONLY SAW BLADES WHERE THE
the bevel adjustment RIVING KNIFE IS NOT THICKER THAN THE WIDTH
to 0°. OF THE GROOVE CUT BY THE SAW BLADE AND
NOT THINNER THAN THE BODY OF THE SAW
2 Unscrew the countersunk BLADE.
head screws and remove the
table insert. WARNING! ENSURE THAT THE SAW BLADE IS
SUITABLE FOR THE MATERIAL TO BE CUT AND
THAT THE MAXIMUM POSSIBLE SPEED IS NOT
LESS THAN THE MAXIMUM TOOL SPEED.
4 Take off the outer flange and pull the old saw blade off the inner
flange by dropping the blade at an angle.
DESCRIPTION OF SYMBOLS
V Volts Hz Hertz
5 Clean the blade flange thoroughly before fitting the new blade.
~ Alternating Current W Watts
Revolutions or reciprocations
6 Mount and fasten the new saw blade following the previous steps /min per minute
n0 No load speed
reverse order. Ensure the blade direction matches the arrow
Wear eye, ear & breathing
direction indicated on the housing. protection
Wear hearing protection
Recycling packaging reduces the need for landfill and raw materials.
Changing the Table Insert Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
To prevent increased likelihood of injury the table insert should be local council authority for recycling advice.
changed whenever it is worn or damaged.