Professional Documents
Culture Documents
Section 6
Section 6
1
• Mechanisms for wear اليات التاكل
1. Adhesive wear. عندما يلتصق سطحين ببعضهما البعض ثم يفصالن
عندما تلتصق جزيئات بسطح الماده واللجوء الي ازالتها عن طريق القطع او السنفرة 2. Abrasive wear.
3. Corrosive wear. تعرض المادة للصدا يودي الي تاكل هذه الماده
4. Surface fatigue. التاكل في منطقة االتصال مثل التروس الدوارة
----------------------------------------------------------------------------------------------------
➢ Selection for thermal properties االختيار طبقا للخواص الحرارية
- Linear expansivity (α) or coefficient of linear expansion: is a measure of
the amount by which a length of material expands when the temperature
increases.
معامل التمدد الخطي :قياس الكمية التي يتمدد بها طول الماده عند زياده درجة الحرارة.
𝑐ℎ𝑎𝑛𝑔𝑒 𝑖𝑛 𝑙𝑒𝑛𝑔𝑡ℎ
=∝ ) (𝐾 −1
𝑒𝑟𝑢𝑡𝑒𝑟𝑝𝑚𝑒𝑡 𝑛𝑖 𝑒𝑔𝑛𝑎𝑜𝑟𝑖𝑔𝑖𝑛𝑎𝑙 𝑙𝑒𝑛𝑔𝑡ℎ ∗ 𝑐ℎ
- Heat capacity: The amount of heat needed to raise the temperature of an
object by l K.
السعة الحرارية :كمية الحرارة الالزمة لرفع درجة حرارة الجسم .1K
- Specific heat capacity (c): is the amount of heat needed per kilogram of
material to raise the temperature by 1 K.
السعة الحرارية النوعية :كمية الحرارة الالزمة لكل كيلوجرام من المادة لرفع درجة الحرارة 1K
𝑡𝑎𝑒𝐴𝑚𝑜𝑢𝑛𝑡 𝑜𝑓 ℎ
= 𝐶 ) (𝐽 𝑘𝑔−1 𝐾 −1
𝑒𝑟𝑢𝑡𝑒𝑟𝑝𝑚𝑒𝑡 𝑛𝑖 𝑒𝑔𝑛𝑎𝑚𝑎𝑠𝑠 ∗ 𝑐ℎ
2
- Thermal conductivity (λ): the ability of a material to conduct heat.
. قدرة المادة علي توصيل الحرارة:معامل التوصيل الحراري
𝐴𝑚𝑜𝑢𝑛𝑡 𝑜𝑓 ℎ𝑒𝑎𝑡
𝛌 = (𝑤 𝑚−1 𝐾 −1 )
𝑡𝑒𝑚𝑝𝑟𝑒𝑡𝑢𝑟𝑒 𝑔𝑟𝑎𝑑𝑖𝑒𝑛𝑡
Solution
𝑐ℎ𝑎𝑛𝑔𝑒 𝑖𝑛 𝑙𝑒𝑛𝑔𝑡ℎ ∆𝐿
∝= = L = 10 cm.
𝑜𝑟𝑖𝑔𝑖𝑛𝑎𝑙 𝑙𝑒𝑛𝑔𝑡ℎ∗𝑐ℎ𝑎𝑛𝑔𝑒 𝑖𝑛 𝑡𝑒𝑚𝑝𝑟𝑒𝑡𝑢𝑟𝑒 𝐿∗ ∆𝑇
∆𝐿 = 30 − 20 = 10℃
∆𝐿 = 𝛼 ∗ ∆𝑇 ∗ 𝐿
𝛼𝑐 = 18 × 10−6
−6 10
∆𝐿𝐶 = 18 × 10 ∗ * 10 = 1.8 * 𝟏𝟎−𝟓 𝒎
100 𝛼𝑝𝑣𝑐 = 75 × 10−6
10
∆𝐿𝑝𝑣𝑐 = 75 × 10−6 ∗ * 10 = 7.5 * 𝟏𝟎−𝟓 𝒎
100
3
Example 2: A bar of copper 40 mm diameter is completely enclosed in a
steel tube 50 mm external diameter; a pin of 18 mm diameter is fitted
transversely to the axis of the bar near each end to secure the bar to the tube.
Calculate the shear stress induced in the pins when the temperature of the
whole system is raised to 100℃, 𝐸𝑐𝑢 = 110 GPa, 𝛼𝑐𝑢 = 1.7 * 10−5 𝐾 −1
𝐸𝑠𝑡 = 210 GPa, 𝛼𝑠𝑡 = 1.17 *10−5 𝐾 −1
Solution
𝜋 𝐷𝑐𝑢 = 40 mm.
𝐴𝑐𝑢 = ∗ (40 ∗ 10−3 )2 = 1.256 ∗ 10−3 𝑚2
4 𝐷𝑠𝑡 = 50 mm.
𝜋 𝐷𝑝𝑖𝑛 = 18 mm.
𝐴𝑠𝑡 = ∗ (50 ∗ 10−3 )2 = 1.963 ∗ 10−3 𝑚2
4
∆𝑇 = 100℃
Actual expansion of steel = actual compression of copper
𝛼𝑐𝑢 = 1.7 * 10−5 𝐾 −1
مقدار التمدد في االستيل = مقدار االنضغاط في النحاس
𝛼𝑠𝑡 = 1.17 *10−5 𝐾 −1
قوة الشد في االستيل = قوة االنضغاط في النحاس
𝐸𝑐𝑢 = 110 GPa
𝐹∗𝐿 𝐹∗𝐿
𝛼𝑠𝑡 ∗ ∆𝑇 ∗ 𝐿 + = 𝛼𝑐𝑢 ∗ ∆𝑇 ∗ 𝐿 − 𝐸𝑠𝑡 = 210 GPa
𝐸𝑠𝑡 ∗ 𝐴𝑠𝑡 𝐸𝑐𝑢 ∗ 𝐴𝑐𝑢
L بقسمة طرفي المعادلة علي
𝐹 𝐹
𝛼𝑠𝑡 ∗ ∆𝑇 + 𝐸𝑠𝑡 ∗𝐴𝑠𝑡
= 𝛼𝑐𝑢 ∗ ∆𝑇 − 𝐸 ∗𝐴
𝑐𝑢 𝑐𝑢
𝐹 𝐹
1.17 *10−5 ∗ 100 + = 1.7 *10−5 ∗ 100 −
210∗109 ∗1.963∗10−3 110∗109 ∗1.256∗10−3