Professional Documents
Culture Documents
performance of material ordered under this specification. TABLE 3 Grain Size for Annealed Sheet
Examples of such requirements include, but are not limited to Thickness,
ASTM Micrograin Average Grain
the following: Size Number, Diameter, max,
in. (mm)
max mm (in.)
4. I. I Alloy-Table I, 0.125 (3.175) and under 3.0 0.127 (0.0050)
Over 0.125 (3.175) 1.5 0.214 (0.00841
4.1.2 Dimensions-Thickness (in decimals of an inch),
width, and length (inch or fractions of an inch),
TABLE 4 Permissible Variations in Thickness of PlateA
4.1.3 Optional Requirement-Plate; how the plate is to be
Permissible Variations in Thickness,
cut (see 7.8.1 and Table 6), Specified Thickness, in. (mm)“c
4.1.4 Cert&ation-State if certification or a report of test in. (mm)
+
results is required (Section IS),
KS to %z (4.762 to 5.556), 0.021 (0.53) 0.010 (0.25)
4. I .5 Purchase Inspecrion-State which tests or inspections incl
Over %2 to j/4 (5.556 to 6.350), 0.024 (0.61) 0.010 (0.25)
are to be witnessed (Section 13), and
incl
4. I .6 Samples for Product (Check) Analysis-State whether Over l/4 to 3/8 (6.350 to 9.525), 0.027 (0.69) 0.010 (0.25)
incl
samples shall be furnished (9.2.2).
Over y8 to ‘12 (9.525 to 12.70), 0.030 (0.76) 0.010 (0.25)
incl
5. Chemical Composition Over % to 5h (12.70 to 15.68), 0.035 (0.89) 0.010 (0.25)
incl
5.1 The material shall conform to the composition limits Over % to z/4 (15.88 to 19.05), 0.040 (1.02) 0.010 (0.25)
incl
specified in Table I. Over 3/4 to 7/8 (19.05 to 22.25). 0.045 (1.14) 0.010 (0.25)
5.2 If a product (check) analysis is made by the purchaser, incl
Over 7/8 to 1 (22.25 to 25.4), 0.050 (1.27) 0.010 (0.25)
the material shall conform to the requirements specified in incl
Table I subject to the permissible tolerances in B 880. Over 1 to 2% (25.4 to 63.5), 5D 0.010 (0.25)
incl
7.2 Thickness:
7. I Weight-For calculations of mass or weight, the follow-
7.2.1 Plate-The permissible variations in thickness of
ing densities shall be used:
plate shall be as prescribed in Table 4.
TABLE 5 Permissible Variations in Thickness of Sheet and StripA gular plates shall be as prescribed in Table 6.
Permissible Variations in 7.3.2 Sheet and Strip--The permissible variations in width
Thickness, in. (mm)
Specified Thickness, for sheet and strip shall be as prescribed in Table 7.
in. (mm) (All Widths)e,’
7.4 Length:
+
7.4.1 Plate-Permissible variations in the length of rectan-
0.020 to 0.034 (0.51 to 0.86) 0.004 (0.10) 0.004 (0.10) gular plate shall be as prescribed in Table 6.
incl
Over 0.034 to 0.056 (0.86 to 1.42), 0.005 (0.13) 0.005 (0.13) 7.4.2 Sheet and Strip-Sheet and strip may be ordered to cut
incl lengths, in which case a variation of % in. (3.175 mm) over the
Over 0.056 to 0.070 (1.42 to 1.78) 0.006 (0.15) 0.006 (0.15)
specified length shall be permitted, with a 0 minus tolerance.
incl
Over 0.070 to 0.078 (1.78 to 1.98) 0.007 (0.18) 0.007 (0.18) 7.5 Straightness:
incl 75.1 The edgewise curvature (depth of chord) of flat sheet,
Over 0.078 to 0.093 (1.98 to 2.36) 0.008 (0.20) 0.008 (0.20)
strip, and plate shall not exceed 0.05 in. (1.27 mm) multiplied
incl
Over 0.093 to 0.109 (2.36 to 2.77), 0.009 (0.23) 0.009 (0.23) by the length in feet or 0.04 mm multiplied by the length in
incl centimetres.
Over 0.109 to 0.125 (2.77 to 3.18) 0.010 (0.25) 0.010 (0.25)
7.5.2 Straightness for coiled strip is subject to agreement
incl
Over 0.125 to 0.140 (3.18 to 3.56), 0.013 (0.33) 0.010 (0.25) between the manufacturer and the purchaser.
incl 7.6 Squareness (Sheer)--For sheets of all thicknesses and
Over 0.140 to 0.171 (3.56 to 4.34), 0.016 (0.41) 0.010 (0.25)
widths of 6 in. (152.4 mm) or more, the angle between adjacent
incl
Over 0.171 to 0.187 (4.34 to 4.75), 0.018 (0.46) 0.010 (0.25) sides shall be 90 I+_0.15 degrees (r/16 in. in 24 in. or 2.6
incl mm/m).
+‘Applicable to sheet 48 in. (1.22 m) and under in width. 7.7 Flatness-Plate, sheet, and strip shall be commercially
sMeasured % in. (9.525 mm) or more from any edge.
flat.
CBuffing for removal of light surface imperfections shall be permitted. The depth
of such buffed areas shall not exceed the permissible minus variation. 7.8 Edges:
7.8.1 Plates shall have sheared, abrasive cut, or plasma-
TABLE 6 Permissible Variations in Width and Length of torch-cut edges as specified.
Sheared, Plasma Torch-Cut, or Abrasive-Cut Rectangular Plate 7.8.2 Sheet and strip shall have sheared or slit edges.
Permissible Variations in Widths and Lengths
for Dimensions Given, in. (mm) 8. Workmanship, Finish, and Appearance
Specified Thickness 8.1 The material shall be uniform in quality and condition,
Up to 30 (760). incl Over 30 (760)
APPENDIX
(Nonmandatory Information)
X 1. I Proper heat treatment during or subsequent to fabri- manufacturer shall be consulted for details.
cation is necessary for optimum performance, and the
The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection
with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such
patent rights, and the risk of infringement of such rights, are entirety their own responsibility
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM Headquarters. Your comments will receive careful consideration at a meeting of the responsible
technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your
views known to the ASTM Committee on Standards, 100 Barr Harbor Drive, West Conshohocken, PA 19428.