Professional Documents
Culture Documents
Simulate Full Wave Rectifier (Both Bridge and Center tapped) with
Resistance as the Load using NGSPICE. Plot the Current and Voltage
waveform at load. Take load as RL =10+ (Roll no. last two digits)/10 kOhms
THERIOTICAL CALCULATIONS :
Roll number:BT21ECE102
R= 10.2k ohms
CIRCUIT :
CODE :
For Full wave bridge rectifier:
e1 2 0 1 0 1
D1 2 3 DIODE
D2 4 2 DIODE
D3 0 3 DIODE
D4 4 0 DIODE
r1 3 4 10.2k
.model DIODE D
.control
run
.probe r1
plot i(r1)
set xbrushwidth = 4
.endc
.end
OUTPUT
For Full wave bridge rectifier:
CIRCUIT:
CODE :
For Center tap full wave rectifier:
e1 2 4 1 0 1
e2 4 0 1 0 1
D1 2 3 DIODE
D2 0 3 DIODE
r1 3 4 10.2k
.model DIODE D
.control
run
.probe r1
plot i(r1)
.probe c1
plot i(c1)
set xbrushwidth = 4
.endc
.end
OUTPUT
For Center tap full wave rectifier:
QUESTION 2:
Simulate Full Wave Rectifier (Both Bridge and Center tapped) with
Capacitance as the Load using NGSPICE. Plot the Current and Voltage
waveform at load. Take Capacitive load CL=1+(roll no./10) nF
THERIOTICAL CALCULATIONS :
Roll number:BT21ECE102
CIRCUIT :
CODE :
For Full wave bridge rectifier:
e1 2 0 1 0 1
D1 2 3 DIODE
D2 4 2 DIODE
D3 0 3 DIODE
D4 4 0 DIODE
r1 3 5 10.2k
c1 5 4 11.2n
.model DIODE D
.control
run
.probe r1
plot i(r1)
set xbrushwidth = 4
.endc
.end
OUTPUT
For Full wave bridge rectifier:
CIRCUIT
CODE :
For Center tap full wave rectifier:
e1 2 4 1 0 1
e2 4 0 1 0 1
D1 2 3 DIODE
D2 0 3 DIODE
c1 3 4 11.2n
.model DIODE D
.control
run
.probe c1
plot i(c1)
set xbrushwidth = 4
.endc
.end
OUTPUT
Simulate Full Wave Rectifier (Both Bridge and Center tapped) with
Resistance and Capacitance Parallel combination as well as series
combination as a Load using NGSPICE. Plot the Current and Voltage
waveform at load. RL =10+(Roll no. last two digits)/10 MOhms CL=1+(roll
no./10) nF
THERIOTICAL CALCULATIONS :
Roll number:BT21ECE102
CIRCUIT :
CODE :
For Full wave bridge rectifier (capacitor and resistor in series):
e1 2 0 1 0 1
D1 2 3 DIODE
D2 4 2 DIODE
D3 0 3 DIODE
D4 4 0 DIODE
r1 3 5 10.2M
c1 5 4 11.2n
.model DIODE D
.control
run
.probe r1
plot i(r1)
set xbrushwidth = 4
.endc
.end
OUTPUT
For Full wave bridge rectifier (capacitor and resistor in series):
CIRCUIT
CODE
For Center tap full wave rectifier (capacitor and resistor in series):
e1 2 4 1 0 1
e2 4 0 1 0 1
D1 2 3 DIODE
D2 0 3 DIODE
r1 4 5 10.2k
c1 5 3 11.2n
.model DIODE D
.control
run
.probe r1
plot i(r1)
set xbrushwidth = 4
.endc
.end
OUTPUT
CIRCUIT
CODE :
For Full wave bridge rectifier (capacitor and resistor in parallel):
e1 2 0 1 0 1
D1 2 3 DIODE
D2 4 2 DIODE
D3 0 3 DIODE
D4 4 0 DIODE
r1 3 4 10.2 M
c1 3 4 11.2n
.model DIODE D
.control
run
.probe r1
plot i(r1)
.probe c1
plot i(c1)
set xbrushwidth = 4
.endc
.end
OUTPUT
For Full wave bridge rectifier (capacitor and resistor in parallel):
CIRCUIT
CODE
For Center tap full wave rectifier (capacitor and resistor in parallel):
e1 2 4 1 0 1
e2 4 0 1 0 1
D1 2 3 DIODE
D2 0 3 DIODE
r1 3 4 10.2M
c1 4 3 11.2n
.model DIODE D
.control
run
.probe r1
plot i(r1)
.probe c1
plot i(c1)
.endc
.end
OUTPUT