Professional Documents
Culture Documents
XN-L E Chap09 Disassembly
XN-L E Chap09 Disassembly
Chapter 9 Disassembly
9.1 XN-XX Housing cover .................................................................................................................1
9.1.1 XN-530/550 .............................................................................................................1
9.1.2 XN-430/450 .............................................................................................................6
2015011
9.1.1 XN-530/550
(1) Use a straight bladed screwdriver to turn the screw on the right side of the housing 90º
counterclockwise to open the right side cover.
(2) Loosen the securing screws on the top right side cover.
Insert
Screws: 2 pcs.
(Right side)
(4) Loosen the securing screws in the cover on the left side, then pull it rearwards to remove it.
Screws: 2 pcs.
Insert
(Left side)
Screws: 2 pcs.
(Right side)
(6) Loosen the screws securing the top cover and remove it.
Insert
Screws: 4 pcs.
(Left side)
Screws: 9 pcs.
(Top)
(8) Open the right side of the front cover and remove the securing screws in the cover.
Screws: 3 pcs.
Cover interior
Inserted
screws
Captive washer
screws M3×6: 4 pcs.
(Rear)
9.1.2 XN-430/450
(1) Use a straight bladed screwdriver to turn the screw on the right side of the housing 90º
counterclockwise to open the right side cover.
(Right side)
Binder screws
M3×6: 2 pcs.
(Right side)
(3) Remove the screws for the right side cover from the rear cover.
Screws: 2 pcs.
(Right side)
Screws: 2 pcs.
Cover NO. 3602
Insert
(Left side)
(5) Remove the cover as shown in the figure. The screws on the other side have only been inserted.
Insert
Screws: 2 pcs.
(Right side)
Insert
Screws: 4 pcs.
(Left side)
(7) Loosen the screws securing the front cover and remove the cover.
(Front)
Screws: 7 pcs.
(Rear)
Small captive
washer screws
M3×6: 4 pcs.
(1) Loosen the screws securing the Mount NO. 7060 and remove it.
Screws: 2 pcs.
(2) Remove the screws securing the Cover NO. 3765 and remove it.
Screws: 2 pcs.
Small captive
washer screws
M3×6: 2 pcs.
(4) Remove the five fluid-line connectors that are connected to the Feeder_ASSY NO. 153.
Fluid-line connector 5
"PC start"
"tube jukou"
"NO. 8131 J1"
"tube hakkou" "BR"
(Front)
(2) After removing the Drive MECH_ASSY NO. 269, remover the CP_UD_LS sensor mentioned
above.
(3) Disconnect the motor connecting cords (“CP_UD”) of the Drive MECH_ASSY NO. 269.
②
"CP_UD_LS" (STM01CW)
①
"CP_UD" (STM01) Drive MECH_ASSY NO. 269
(Front)
(2) Disconnect tube connected to pipette and cut tie wraps to cable tie securing the tube.
Convex
CV-100
(4) Loosen the screws securing the Dispenser_ASSY NO. 37 and remove it.
Screws: 5 pcs.
Dispenser_ASSY NO. 37
(Right side)
Screws:
4 pcs.
"SET_LS-1"
(Front)
“CPU USB”
USB1
(3) Remove wiring cord from clamps on the front panel.
Clamp:3 pcs
(Front)
Clamp: 1 pc.
"WDF_1" "RET"
Take care not to bend the tube.
WDF_1
RET
Binder screws
M3×6: 2 pcs.
Small captive
washer screws
(Front) M3×6: 3 pcs.
(Left side)
ASP_ASSY
NO. 62
Small captive
washer screws (Left side) (Front)
M3×6: 2pcs.
ASP_ASSY NO. 62