Professional Documents
Culture Documents
T1 + T2
Ready
Diagram 2: Set sensor parameters via Teach-in procedure Diagram 3: Key lock and factory setting
Place object at position 1 . Place object at position 1 . Place reflector at position 1 . While pressing T1 turn While pressing T1 turn
supply voltage ON. supply voltage ON.
Diagram 4: Useful additional functions in Add-on menu (for experienced users only, settings not required for standard applications)
Start here
T1 + T2
T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2
T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2
T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2
T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2
T2 T1
T1 + T2 »C01«: Display Minimum value: »F00«: no filter Defines the strength Minimum value: »00«: synchronisati- To optimize multi- Minimum value: Put plane reflector Affects the size of
bright »001« »F01«: standard of the chosen filter. blind zone on plex speed the hig- sensor-distant vertically disposed in the detection zone.
hest sensor address window limit front of sensor: in
Ready »C02«: Display
dimmed
Maximum value:
difference between
filter
»F02«: averaging
»P00«: weak filter
up to
Maximum value: ne-
arwindow limit - 1
»01« to »10«: sensor
address for multi- may be set. Maximum value: an exact distance of
»E01«: high
»E02«: standard
maximum range and plex mode Setting range »01« 999 mm for 250 mm for
»C03«: Display off filter »P09«: strong filter crm+ 25... and »E03«: slight
switching point - 1 »oFF«: synchronisati- to »10« crm+25/...,
»F03«: foreground crm+35/..., crm+35... and
During window filter on deactivated 900 mm for all other
mode operation 999 cm for types.
hysteresis influences »F04«: background crm+130/...,
both switching filter crm+340/..., Adjust display to
points. crm+600/... 250 mm or 900 mm.
Note Confirm calibration
Changes in the Add-on menu with T1+T2.
may impair the sensor func-
tion.
A6, A7, A10, A11, A12 have
influence on the response
time of the sensor. Low power mode Hysteresis Measurement filter Filter strength Foreground Multiplex mode Multiplex mode Measurement range Calibration Detection zone
switched output suppression device addressing highest address display sensitivity
Technical data
1
+UB crm+25... crm+35... crm+130... crm+340... crm+600...
2
U 4 TouchControl 36 width A/F TouchControl 36 width A/F TouchControl 36 width A/F TouchControl 36 width A/F TouchControl 36 width A/F
5
F/ LED-Display LED-Display LED-Display LED-Display LED-Display
Sync/Com 2 Buttons M30x1.5 5 2 Buttons M30x1.5 5 2 Buttons M30x1.5 5 2 Buttons M30x1.5 5 2 Buttons M30x1.5 5
3 2 Duo-LEDs 2 Duo-LEDs 2 Duo-LEDs 2 Duo-LEDs 2 Duo-LEDs
–UB
1 Push-Pull output in pnp circuit
Ø47.5
Ø65
1
+UB
M12x1
M12x1
M12x1
M12x1
M12x1
2
U 4
5
F/ 19.5
Sync/Com 33
22.5
3
–UB 51 51 51 69
36
72
1 Push-Pull output in npn circuit 84 84 84 102 105
detection zones
10 cm
10 cm
2.4 m
1.2 m
1.2 m
2.4 m
0.8 m
0.4 m
0.4 m
0.8 m
1.6 m
0.8 m
0.8 m
1.6 m
20 cm
10 cm
10 cm
20 cm
5 cm
0 cm
5 cm
0 cm
for different objects:
0m
0m
0m
The dark grey areas represent the 0 cm 0 cm 0m 0m 0m
zone where it is easy to recognise
the normal reflector (round bar).
This indicates the typical operating 5 cm
10 cm 0.8 m 1.2 m
range of the sensors. The light Plate 0.4 m Plate Plate
Plate
grey areas represent the zone Plate
where a very large reflector – for 10 cm 1.6 m 2.4 m
20 cm Round bar ø 27 mm
instance a plate – can still be re- Round bar ø 10 mm Round bar ø 27 mm
Round bar ø 10 mm 0.8 m
cognised. The requirement here is 15 cm Round bar ø 10 mm 2.4 m 3.6 m
for an optimum alignment to the 30 cm
sensor. It is not possible to evalua- 1.2 m
te ultrasonic reflections outside 35 cm
20 cm 1.3 m 3.2 m 4.8 m
this area. 40 cm 3.4 m
25 cm 1.6 m 4m 6m
50 cm
30 cm 4.8 m 7.2 m
2m
60 cm
35 cm 5.6 m 8.4 m