Professional Documents
Culture Documents
www.tyco-fire.com
Contacts
General
Description
The TYCO 1-1/2 inch to 8 inch (DN40
to DN200), DV-5 Deluge Valves are dia-
phragm type valves designed for ver-
tical or horizontal installation and for
fire protection system service. They
are used as automatic water control
TE
valves in deluge, preaction, and special
types of fire protection systems such
as foam-water and double interlock
systems. When properly trimmed, the
DV-5 Valves are also able to provide
actuation of fire alarms upon system
operation.
LE
NOTICE
These valves are to be used only for
hydraulically calculated systems.
The diaphragm style design of the DV-5
O
Valve allows external resetting, provid-
ing for easy resetting of a deluge or
preaction system without having to
open a valve handhole cover to man-
BS
IMPORTANT
Refer to Technical Data Sheet
TFP2300 for warnings pertaining to
regulatory and health information.
NOTES:
VALVE PARTS REPLACEMENT PARTS
No. Description Qty. Repair Parts
1. NR - Not Replaceable No. Description P/N
2. CH - Common Hardware
1 Valve Body . . . . . . . . . . . 1 NR (a) Diaphragm Kit,
2 Diaphragm . . . . . . . . . . . 1 (a) 3. Valve Bodies of 4, 6 and 8 Inch (DN100, Includes Item 2:
3 Diaphragm Cover. . . . . . . 1 NR DN150 & DN200) valves are equipped 1-1/2 Inch (DN40) Valve . . . . 92-477-1-105
4 Flat Washer, Metric: with studs and Valve Covers are secured 2 Inch (DN50) Valve . . . . . . . 92-477-1-107
1-1/2 Inch (DN40) Valve, by Hex Nuts and Hex Bolts. 3 Inch (DN80) Valve . . . . . . . 92-477-1-109
M12 . . . . . . . . . . . . . . . . . 4 CH 4 Inch (DN100) Valve . . . . . . . 92-477-1-101
2 Inch (DN50) Valve &
4. V-Ring is attached to Diaphragm of 4, 6 6 Inch (DN150) Valve . . . . . . . 92-477-1-103
3 Inch (DN80) Valve, and 8 Inch (DN100, DN150 & DN200) 8 Inch (DN200) Valve . . . . . . . 92-477-1-111
M16 . . . . . . . . . . . . . . . . . 4 CH valves at factory. If, during internal valve
4 Inch (DN100) Valve & inspection, V-Ring is discovered to be
6 Inch (DN150) Valve, detached from Diaphragm, be advised
M16 . . . . . . . . . . . . . . . . . 8 CH that V-Ring is a required valve component
8 Inch (DN200) Valve, and that detachment will not affect normal
M20 . . . . . . . . . . . . . . . . . 8 CH valve operation or performance. Should
5 Hex Bolt, Metric: V-Ring become detached, reinstall
1-1/2 Inch (DN40) Valve,
M12 x 30 mm. . . . . . . . . . 4 CH
between Diaphragm and Diaphragm
2 Inch (DN50) Valve & Cover concentrically as shown. STUDS
3 Inch (DN80) Valve, (NOTE 3)
NOTE: Do not apply adhesives, lubricants, 2
M16 x 50 mm. . . . . . . . . . 4 CH
4 Inch (DN100) Valve,
or other substances to Diaphragm, V-Ring, (NOTE 4)
M16 x 50 mm. . . . . . . . . . 6 CH or Valve Body.
6 Inch (DN150) Valve,
TE
M16 x 55 mm. . . . . . . . . . 6 CH
8 Inch (DN200) Valve,
M20 x 70 mm. . . . . . . . . . 6 CH
6 Hex Nut, Metric:
4 Inch (DN100) Valve &
6 Inch (DN150) Valve, 4
M16 . . . . . . . . . . . . . . . . . 2 CH 6
8 Inch (DN200) Valve,
M20 . . . . . . . . . . . . . . . . . 2 CH
LE (NOTE 3)
1
DIAPHRAGM
ORIENTATION
ORIENT
O
TAB
DIAPHRAGM TAB V-RING
PERPENDICULAR (NOTE 4)
5
TO VALVE BODY
CENTERLINE 4 3
BS
FIGURE 1
DV-5 DELUGE VALVE
ASSEMBLY
Notes:
1. Flange end 1-1/2 & 2 Inch (DN40 & DN50) DV-5 Valves are not offered.
2. Same drilling as for B16.5 (Class 150) and B16.42 (Class 250).
3. Same drilling as for BS 4504 Section 3.2 (PN10) and DIN 2532 (PN10).
4. Same drilling as for BS 4504 Section 3.2 (PN16) and DIN 2532 (PN16).
TABLE A
DIMENSIONAL SPECIFICATIONS
FOR SELECTION OF FLANGE DRILLING
TFP1305
Page 3 of 8
VALVE DIAPHRAGM
TE
WATERWAY VALVE CHAMBER
DIAPHRAGM WATERWAY OPEN TO
SEAT ATMOSPHERE
DIAPHRAGM
RETRACTS
LE DIAPHRAGM
OPENING
CHAMBER
WATER VALVE
SUPPLY
SUPPLY WATERWAY
PORT
PRESSURE
& ALARM
250 PSI MAX. WATER SUPPLY WATERFLOW FROM WATER SUPPLY
TEST PORT
O
FIGURE 2A FIGURE 2B
SET POSITION OPERATED POSITION
DIAPHRAGM
AUTOMATICALLY
SYSTEM FLEXES TO
SYSTEM
O
MAIN
DRAIN
PORT
FIGURE 2
DV-5 DELUGE VALVE
SET AND OPEN POSITIONS
TFP1305
Page 4 of 8
NOTICE
The DV-5 Deluge Valves de s cribed
Materials of
8"
(204 mm)
herein must be installed and main-
tained in compliance with this docu-
Construction
ment and with the applicable standards
of the NATIONAL FIRE PROTECTION NOTICE
1-1/2 Inch (DN40) ASSOCIATION (NFPA), in addition to The RILSAN coating for the DV-5 Valve
Groove x Groove & Thread x Thread the standards of any other authorities provides corrosion resistance and is
having jurisdiction. Failure to do so intended to extend the life of the DV-5
may impair the performance of these Valve when exposed to internal and
devices. external corrosive conditions. Although
8-5/8" the RILSAN coating is intended to
The owner is responsible for maintain resist corrosion, it is recommended
(220 mm)
ing their fire protection system and that the end user or other technical
devices in proper operating condi- expert familiar with conditions at the
tion. Contact the installing contrac- proposed installation be consulted with
2 Inch (DN50) tor or product manufacturer with any respect to the suitability of this coating
Groove x Groove & Thread x Thread questions. for a given corrosive condition.
TE
Approvals system ideally should be configured
UL and C-UL Listed for hydraulically with a primary source of clean fresh
calculated systems, and FM Approved, water (e.g., a pressurized water tank)
3 Inch (DN80) when trimmed per the following Techni- and only upon system operation is the
Groove x Groove, Flange x Flange, cal Data Sheets: secondary water supply (seawater or
& Flange x Groove brackish water) allowed to enter the
• Deluge Systems: system. After the system operation,
LE
TFP1310 -Wet Pilot Actuation
the system should then be thoroughly
TFP1315 -Dry Pilot Actuation
TFP1320 -Electric Actuation flushed with clean fresh water. Follow
15-3/4"
ing this recommendation will increase
• Single Interlock Preaction Systems: the service life of the DV-5 Valve and
(400 mm) TFP1410 -Wet Pilot Actuation*
TFP1415 -Dry Pilot Actuation* Valve Trim.
O
TFP1420 -Electric Actuation Body
*UL and C-UL only
4 Inch (DN100) RILSAN polyamide 11 coated ductile
Groove x Groove, Flange x Flange, • Double Interlock Preaction Systems: iron per ASTM A536-77, Grade
& Flange x Groove TFP1460 -Electric/Pneumatic 65-45-12
BS
TFP1465 -Electric/Electric
Handhole Cover
Deluge Valve RILSAN polyamide 11 coated ductile
Components for the 1-1/2 inch to 8 inch iron per ASTM A536-77, Grade
18-1/8" (DN40 to DN200), DV-5 Deluge Valves 65-45-12
(460 mm) are shown in Figure 1. The DV-5 Valves
are for vertical or horizontal installa- Diaphragm
O
tions, and they are rated for use at a Nylon fabric reinforced, natural rubber
maximum service pressure of 250 psi per ASTM D2000
6 Inch (DN150) (17,2 bar). V-Ring
Groove x Groove, Flange x Flange, Natural rubber per ASTM D2000
& Flange x Groove
The take-out dimensions are shown in
Figure 3, and the flanged connections Diaphragm Cover Fasteners
are available drilled per ANSI, ISO, AS, Galvanized carbon steel
and JIS specifications (Ref. Table A).
Threaded port connections of the DV-5
22-1/2" Valves are available NPT threaded or
(570 mm) threaded per ISO 7/1 as detailed in the
Ordering Procedure section. Valves
with NPT threaded ports will readily
accept the trim arrangements detailed
in Technical Data Sheets referenced
8 Inch (DN200) under “Approvals”.
Groove x Groove, Flange x Flange,
& Flange x Groove
FIGURE 3
DV-5 DELUGE VALVE
TAKE-OUT DIMENSIONS
TFP1305
Page 5 of 8
6.0
NOMINAL PRESSURE DROP IN POUNDS PER SQUARE INCH (PSI)
0,400
5.0 40)
DN
0,300
50)
H(
4.0
INC
DN (
CH
3.0
1 -1
0,200
80)
2 IN
DN
DN
2.0
3 IN
(
CH
)
150
4 IN
(DN
0,100
)
200
TE
0,090
CH
(DN
0,080
6 IN
CH
1.0 0,070
8 IN
0.9 0,060
0.8
0.7 0,050
LE
0.6 0,040
0.5
0,030
0.4
O
0,022
0.3
50 100 200 400 600 1000 2000 3000 4000
BS
The approximate friction loss, based on the Hazen and Williams formula and expressed in equivalent length of pipe with C=120, is
as follows:
16 feet of 2 inch Sch. 40 pipe for the 2 inch DV-5 Valve calculated on a typical flow rate of 175 GPM.
20 feet of 3 inch Sch. 40 pipe for the 3 inch DV-5 Valve calculated on a typical flow rate of 350 GPM.
O
29 feet of 4 inch Sch. 40 pipe for the 4 inch DV-5 Valve calculated on a typical flow rate of 600 GPM.
46 feet of 6 inch Sch. 40 pipe for the 6 inch DV-5 Valve calculated on a typical flow rate of 1500 GPM.
72 feet of 8 inch Sch. 30 pipe for the 8 inch DV-5 Valve calculated on a typical flow rate of 2500 GPM.
GRAPH A
DV-5 DELUGE VALVE
NOMINAL PRESSURE LOSS VERSUS FLOW
TE
• Close the Main Drain Valve.
Before a system hydrostatic test is per- impairment as defined by NFPA 25.
formed refer to the Installation section Should this condition occur, immedi- Step 2. Determine the type of actua
of Technical Data Sheets TFP1310, ately close the main control valve and tion/detection system, and operate the
TFP1315, TFP1320, TFP1410, TFP1415, utilize the following procedure to reset DV-5 Valve accordingly.
TFP1420, TFP1460, or TFP1465. the system:
NOTICE
Care and
LE
Step 1. Prior to the water supply pres-
sure being restored to the closed main Be prepared to quickly perform Steps
3, 4, and 5 if water must be prevented
Maintenance
control valve, note the pressure indi-
cated by the diaphragm chamber from flowing beyond the riser.
press ure gauge and determine if • Wet Pilot Actuation — Open the
The following procedures and inspec the pres s ure is within the normally
tions must be performed as indicated, Inspector’s Test Connection.
O
expected range.
in addition to any specific requirements • Dry Pilot Actuation — Open the
of the NFPA. Any impairment must be Step 2. If the diaphragm chamber pres- Inspector’s Test Connection.
immediately corrected. sure is below the normal range, check
for and correct any source of leakage • Electric Actuation — Test the
BS
Before closing a fire protection system from the diaphragm chamber prior to deluge releasing panel (automatic
main control valve for maintenance resetting the system. control unit) in accordance with
work on the fire protection system the manufacturer’s instructions to
that it controls, obtain permission to Step 3. After the water supply pressure energize the solenoid valve.
shut down the affected fire protection is restored to the main control valve,
system from the proper authorities reset the DV-5 Deluge Valve in accor- Step 3. Verify that the DV-5 Valve has
and notify all personnel who may be dance with the Valve Setting Procedure tripped, as indicated by the flow of
O
TE
8 Inch G x G
8.62 inch (219,1 mm)
When reinstalling the Diaphragm Cover,
complete the following steps to assure Warranty Groove O.D. x 8.62
inch (219,1 mm)
the Diaphragm Cover Fasteners (Hex Groove O.D ���������������������������������� 52-477-1-916
For warranty terms and conditions, visit
Bolts) are uniformly and securely 8 Inch F x F
www.tyco-fire.com. ANSI Flange x
tightened.
ANSI Flange �������������������������������� 52-477-1-016
LE
Step 1. Align Diaphragm and Dia-
phragm Cover in proper orientation Ordering 8 Inch F x G
ANSI Flange x
with valve body (Ref. Figure 1) and hold
in place Procedure 8.62 inch (219,1 mm)
Groove O.D. �������������������������������� 52-477-1-416
Step 4. Insert Hex Bolts through Dia- DV-5 Valves are provided in the Price Valves
phragm Cover and Diaphragm, hand- Book.
tighten into valve body
Step 5. Using crossdraw sequence to Standard DV-5 Deluge Valve
assure uniformity, wrench-tighten Hex (American Standard Flange
Bolts to appropriate torque values (Ref. Drilling, Threaded Ports, and
Table B) Groove Outside Diameter, as
O
Other DV-5 Deluge Valves JIS Flange x Other 8 Inch Valves with ISO Ports
4.50 inch (114,3 mm) ISO (PN10) Flange x
NOTICE Groove O.D. ��������������������������������52-477-4-813 ISO (PN10) Flange �����������������������52-477-1-116
Other 4 Inch Valves with ISO Ports ISO (PN16) Flange x
Other DV-5 Deluge Valves are valves ISO Flange x ISO (PN16) Flange ���������������������� 52-477-1-126
ordered with any combination of flange, ISO Flange ���������������������������������� 52-477-4-113 ISO (PN10) Flange x
threaded port, or groove outside diam- ISO Flange x 8.62 inch (219,1 mm)
eter not offered under “Standard DV-5 4.50 inch (114,3 mm) Groove O.D. �������������������������������� 52-477-1-216
Groove O.D. ��������������������������������52-477-4-213
Deluge Valve” offerings. ISO (PN16) Flange x
4.50 inch (114,3 mm) 8.62 inch (219,1 mm)
Valves with NPT threaded ports are Groove O.D x Groove O.D. �������������������������������� 52-477-1-226
intended for use with the “Standard 4.50 inch (114,3 mm) 8.62 inch (219,1 mm)
Groove O.D. ��������������������������������52-477-1-923 Groove O.D. x
DV-5 Valve Trim” offered and detailed
Other 6 Inch Valves with NPT Ports 8.62 inch (219,1 mm)
in Technical Data Sheets TFP1310, ANSI Flange x Groove O.D. ��������������������������������52-477-1-926
TFP1315, TFP1320, TFP1410, TFP1415, 6.50 inch (165,1 mm)
TFP1420, TFP1460, and TFP1465. Groove O.D. ������������������������������� 52-477-4-225
Valves with ISO threaded ports are ISO Flange x
intended for use with special order trim 6.62 inch (168,3 mm)
Groove O.D. ������������������������������� 52-477-5-625
that is provided by local distributors
ISO Flange x
to meet the specific needs of certain 6.50 inch (165,1 mm)
localities. Please contact your local dis- Groove O.D. ��������������������������������52-477-5-215
tributor regarding valves and valve trim ISO Flange x
for specific localities. ISO Flange ���������������������������������� 52-477-5-115
6.50 inch (165,1 mm)
Specify: (specify size) DV-5 Deluge Groove O.D x
TE
Valve with (specify) connections with 6.50 inch (165,1 mm)
(specify NPT or ISO) threaded ports, Groove O.D. ��������������������������������52-477-1-935
P/N (specify): AS Flange x
AS Flange ������������������������������������52-477-4-315
Part Numbers for Other DV-5 AS Flange x
6.62 inch (168,3 mm)
Deluge Valves Groove O.D. ��������������������������������52-477-4-415
Other 1-1/2 Inch Valves with ISO Ports
ISO Thread x AS Flange x
LE
ISO Thread ���������������������������������� 52-477-1-169 6.50 inch (165,1 mm)
Groove O.D. ��������������������������������52-477-5-415
Other 2 Inch Valves with ISO Ports
ISO Thread x JIS Flange x
ISO Thread ���������������������������������� 52-477-1-160 JIS Flange ������������������������������������52-477-4-715
Other 3 Inch Valves with NPT Ports JIS Flange x
6.62 inch (168,3 mm)
O
ISO Flange x
3.50 inch (88,9 mm) Groove O.D. ��������������������������������52-477-4-815
Groove O.D. �������������������������������� 52-477-1-252 JIS Flange x
ISO Flange x 6.50 inch (165,1 mm)
ISO Flange ���������������������������������� 52-477-1-132 Groove O.D. ��������������������������������52-477-5-815
BS