Professional Documents
Culture Documents
PS2045
Mechanical-Seeder
1/1
Part number 47918066 Part number 47918066
English
January 2015
PS2045 Mechanical
47918066 10/09/2015
EN
Contents
INTRODUCTION
Machine completion and equipment .............................................. 05
[05.102] Machine completion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05.1
Hydraulic systems....................................................................... 35
[35.162] Front hitch cylinders and lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35.1
Wheels ...................................................................................... 44
[44.530] Carrying and transport wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.1
Seeding..................................................................................... 77
[77.100] Product handling and delivery drive system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77.1
47918066 10/09/2015
Platform, cab, bodywork, and decals ............................................. 90
[90.118] Protections and footboards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90.1
47918066 10/09/2015
47918066 10/09/2015
INTRODUCTION
47918066 10/09/2015
1
Contents
INTRODUCTION
Safety rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Basic instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Basic instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Special tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
General specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Dimension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
General specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Conversion factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Product identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Part identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
47918066 10/09/2015
2
INTRODUCTION
Safety rules
PERSONAL PROTECTIVE EQUIPMENT (PPE) RECOMMENDED
1. Ear protector.
2. Gloves.
3. Boots (with steel toe).
4. Overalls.
5. Glasses.
BAIL14SE00801AA 1
SEM19101776 2
47918066 10/09/2015
3
INTRODUCTION
BAIL14SE00801AC 4
BAIL14SE00824AC 5
BAIL14SE00824AB 6
47918066 10/09/2015
4
INTRODUCTION
ATTENTION: This word indicates special technical instructions that, if not observed, can cause malfunction, damage
to the machine and even risk of injury.
ATTENTION: This word indicates special technical instructions that, if not observed, can cause damage to the ma-
chine and imminent risk of injury, and even death.
• Prefer the use of trucks to transport the machine, especially when it comes to public roads.
• Seek information about what is allowed and the order recommended by the local traffic authorities.
• For operations performed by default of the current regulations, the consequences must be borne by the operator.
• Use alerting devices, such as flags, slow vehicle emblems, lights, etc., approved by the current local traffic laws.
Keep these devices clean and in good condition.
• Practice speeds compatible with the road conditions and traffic, but never exceeding 12.5 MPH (20 km/h).
Reduce the speed considerably when the surface is uneven.
NOTE: Do not transport the machine loaded: supply the seed at the planting site.
For maintenance services performed with the Seeder coupled onto the tractor.
For many maintenance tasks, especially those performed in the field, it is convenient to leave the Seeder coupled to
the tractor to ensure the firmness and stability of the machine. In addition:
UNDER MAINTENANCE
DO NOT OPERATE
BAIL14SE00801AF 7
47918066 10/09/2015
5
INTRODUCTION
BAIL14SE00801BA 8
47918066 10/09/2015
6
INTRODUCTION
SEM19101779 10
SEM19101760 11
BAIL14SE00801AG 12
47918066 10/09/2015
7
INTRODUCTION
SEM19101786 14
SEM19101761 15
Tire calibration:
• Never exceed the recommended pressure to seat the
edges of the tire on the rim.
• Replace the tire if it presents any defects. Replace the
rim if you observe any sign of cracks, wear, deformation
or severe corrosion.
• Make sure all the air was removed prior to removing the
tire from the rim.
• Make sure the tire is properly seated on the rim during
its filling.
• Tire replacement can be dangerous and must be
performed by trained personnel with proper tools and
equipment.
• Never stand in front or on top during the mounting of a
tire.
• When removing and installing wheels, use suitable han-
dling equipment for the weight involved. If available,
use a safety cage to perform this type of operation.
BAIL14SE00801BB 16
47918066 10/09/2015
8
INTRODUCTION
Care taken with hydraulic systems and fluids under pressure in general
• Fluids escaping under pressure can penetrate the skin,
causing injury and serious poisoning; fluids injected into
the skin must be surgically removed as soon as possi-
ble, as they may cause gangrene.
• To check for leaks, use a piece of paper or cardboard,
not body parts.
• If an accident occurs, see a doctor immediately.
• Wear protective gloves and goggles when working with
hydraulic systems.
BAIL14SE00801AH 17
Avoid fires
• Keep a fire extinguisher and a first aid kit always at hand
also Keep emergency numbers for doctor, ambulance,
hospital and firefighter near the phone.
• Never allow open flame or welding near fluids,
flammable gases, paints, solvents and other!
• Do not smoke at the work place. There is always the
risk of fire due to the wide range of flammable products.
• When welding, remove any flammable products from
near the area to be welded, such as fuels, solvents or
lubricants.
BAIL14SE00801AJ 18
47918066 10/09/2015
9
INTRODUCTION
BAIL14SE00801BC 19
47918066 10/09/2015
10
INTRODUCTION
Welding work
• Use the proper PPE for this activity: mask, gloves and
a leather apron.
• In case of electric welding: always seek to connect the
negative electrode near the point to be welded.
• Only perform welding in well ventilated areas to avoid
the concentration of toxic gases and dust.
• Before welding, remove the paint, thus preventing the
formation of toxic gases and dust.
If you cannot remove the paint, use an appropriate
mask to protect against the inhalation of toxic gases.
When sanding surfaces, especially with paint, also
wear a mask.
If you use a solvent to remove the paint, do not forget SEM19101776 20
47918066 10/09/2015
11
INTRODUCTION
Basic instructions
HITCH THE MACHINE ONTO THE TRACTOR
CAUTION
Transport hazard!
Always connect a safety chain between the machine and the implement. Only use a safety chain with
a strength rating equal to or greater than the gross weight of the implement.
Failure to comply could result in minor or moderate injury.
C0039A
CAUTION
Avoid injury!
Handle all parts carefully. Do not place your hands or fingers between parts. Use Personal Protec-
tive Equipment (PPE) as indicated in this manual, including protective goggles, gloves, and safety
footwear.
Failure to comply could result in minor or moderate injury.
C0145A
DANGER
Crushing hazard!
Do not stand or place any body part between the implement and a moving tractor. Stop the tractor
engine and set the parking brake before you attach cables and hoses.
Failure to comply will result in death or serious injury.
D0112A
BAIL14SE00810AV 1
BAIL14SE00810AW 2
47918066 10/09/2015
12
INTRODUCTION
Safety chain
The chain (3) has the main function of safety in case of
accidental disengagement of the machine.
Engage the chain end (2) in the top link of the tractor's
hitch system.
The current (3) can be adjusted* to act as descent limiting
of the lift arms, and therefore the drawbar (1).
NOTE: *By the choice of the links connected to the chain
end (3a).
BAIL14SE00810AU 3
BAIL14SE00810BE 4
Hydraulic coupling
After engaging the bar (2) to the lower lift arms, attach
the hoses (4) of the Seeder in the tractor's remote quick
couplers.
NOTICE:
• Before coupling the seeder hydraulic cylinder hoses,
clean the surface of the quick coupler.
• When not using the quick coupler, keep the plastic cap
in place.
• Do not couple onto the tractor's hydraulic system, hy-
draulic systems containing impurities in its circuit, since
apart from contaminating the tractor's hydraulic oil, it can
cause damage to its components.
BAIL14SE00810AX 5
47918066 10/09/2015
13
INTRODUCTION
HYDRAULIC SYSTEM
Through the triple control valve (5) assembled on the
machine frame, and the joystick type electric control (6),
attached to the tractor, is possible to select the desired
hydraulic function:
• I — up / down the transport drive wheels.
• II — lift row units (free passage of oil, circuit without
solenoid valve).
• III — moves the drawbar of the machine between the
transport and operation mode.
NOTE: After using the control (6) in position "I or III", re-
turn the control lever to the center position. This will pre-
vent the heating of the control valve coil (6). BAIL14SE00810AZ 6
47918066 10/09/2015
14
INTRODUCTION
Torque
NOTE: The machines are designed with SI standard metric measurements.
BAIL14SE00802AO 1
NOTE: In case a special torque is specified for a given bolt or nut, do not use the values in the tables below.
NOTE: When applying the recommended torque, make sure the threads are clean.
NOTE: When replacing bolts and/or nuts, use new items with a class equal or superior to the original ones. However,
when using a new bolt or nut of a higher class, apply the original torque only.
47918066 10/09/2015
15
INTRODUCTION
Recommended torque for steel hydraulic connections: straight threads with "O" ring
Tube's external diameter / hose's internal diameter Thread size Torque in N.m
mm in
6.4 mm 1/4 in 7/16-20 in 8 - 16 N.m
7.9 mm 5/16 in 1/2-20 in 11 - 22 N.m
9.5 mm 3/8 in 9/16-18 in 14 - 34 N.m
12.7 mm 1/2 in 3/4-16 in 20 - 57 N.m
15.9 mm 5/6 in 7/8-14 in 34 - 79 N.m
19.0 mm 3/4 in 1-1/16-12 in 54 - 108 N.m
22.2 mm 7/8 in 1-3/16-12 in 81 - 135 N.m
25.4 mm 1 in 1-5/16-12 in 102 - 158 N.m
31.8 mm 1-1/4 in 1-5/8-12 in 169 - 223 N.m
38.1 mm 1-1/2 in 1-7/8-12 in 285 - 338 N.m
Recommended torque for steel hydraulic connections: straight threads with "O" ring
Tube's external diameter / hose's internal diameter Thread size Torque in N.m
mm in
6.4 mm 1/4 in 7/16-20 in 8 - 16 N.m
7.9 mm 5/16 in 1/2-20 in 11 - 22 N.m
9.5 mm 3/8 in 9/16-18 in 14 - 34 N.m
12.7 mm 1/2 in 3/4-16 in 20 - 57 N.m
15.9 mm 5/6 in 7/8-14 in 34 - 79 N.m
19.0 mm 3/4 in 1-1/16-12 in 54 - 108 N.m
22.2 mm 7/8 in 1-3/16-12 in 81 - 135 N.m
25.4 mm 1 in 1-5/16-12 in 102 - 158 N.m
31.8 mm 1-1/4 in 1-5/8-12 in 169 - 223 N.m
38.1 mm 1-1/2 in 1-7/8-12 in 285 - 338 N.m
47918066 10/09/2015
16
INTRODUCTION
Basic instructions
INSTALLATION OF SNAP RINGS
In the case of Seeger type rings (1) internal or external,
installed and removed with pliers fitted in two holes (2)
check for the correct side in the installation of the rings.
This is because the holes (2) for fitting the pliers (3) are
tapered:
• Correct way of installation: the side with the smallest
diameter of the tapered holes (2) must face the pliers
(3).
Thus, the ring (1) does not escape from the pliers.
• Incorrect way: if the ring (1) was installed with the side
with the largest diameter of the tapered holes facing the
pliers, their tips would be pushed inside out, preventing BAIL14SE00802AP 1
or hindering the coupling.
ATTENTION: Always wear protective goggles when work-
ing with snap rings. The escape of a snap ring from the
plier tips causes a violent fling of the ring!
BAIL14SE00802AQ 2
BAIL14SE00802AR 3
47918066 10/09/2015
17
INTRODUCTION
BUSHING REPLACEMENT
Bushing removal
• Generally, bushings mounted under interference are re-
moved only when they need to be replaced.
• The removal can therefore be destructive. However,
be careful not to damage the part where the bushing is
mounted.
BAIL14SE00802AS 4
REPLACEMENT OF SEALS
NOTE: The fundamental care in the installation of seals
consists in not to deform them. This requires the use of
appropriate tools
NOTE: Once removed, the seals cannot be reinstalled:
replace them.
47918066 10/09/2015
18
INTRODUCTION
BAIL14SE00802BF 7
47918066 10/09/2015
19
INTRODUCTION
Move the seal until the rigid face reaches the bottom of
the housing, but without forcing it.
Observations:
• The displacement of the seal into the housing must be
in an aligned manner. Therefore, it is important that the
tool (3) has an extension that facilitates the alignment.
• Before installing a seal, make sure that the housing is
clean and dry, free of grease or oil.
BAIL14SE00802AV 8
• After installing the seal, grease the seal lip.
• Take care when mounting the shaft that goes through
the seal, especially spline shafts with key slot and an-
other type of edge that can damage the retainer lip.
• Tiny cuts on the lip cause leaks.
This way, the seal does not have the function of allowing
the outflow of excess grease. Therefore, it is installed with
the lip facing inward (and the flat face outwards).
BAIL14SE00802AX 10
47918066 10/09/2015
20
INTRODUCTION
BAIL14SE00802AY 11
BAIL14SE00802AZ 12
For installation
• Never install a bearing applying direct hammer blows
on it!
• Prefer the use of presses for installing bearings. For
field installations, a hammer can be used, however, the
bearing needs to be displaced in an aligned manner by
an appropriate tool.
• Lubricate the bearings before or after their installation.
NOTICE: The force to install the bearing should only
be applied on the track (internal or external) which is
installed with interference.
NOTICE: If the force (of the press or the hammer blows)
is applied on the free track, the balls and cages of the BAIL14SE00803AN 13
bearing could suffer serious damage.
• So to install bearings in holes, press the outer ring, and
to install bearings on shafts, press the inner ring.
• For the installation with both a press or a hammer, the
bearing must be lying on a flat, firm surface and per-
pendicular to the tool or press used in the installation.
47918066 10/09/2015
21
INTRODUCTION
BAIL14SE00803AO 14
BAIL14SE00803AP 15
BAIL14SE00803AQ 16
47918066 10/09/2015
22
INTRODUCTION
GENERAL RECOMMENDATIONS
ASSEMBLY SIDE
• Several components of the machine have parts whose
assembly side must be observed.
• In the row units, such components have a marking, in-
dicating it should be installed on the right side (from the
point of view of who is behind the machine). See ex-
amples in the figure, indicated by the arrows.
BAIL14SE00803AS 18
Bolts in general
In the case of bolts that allow the installation in both direc-
tions, the standard factory installation is from left to right.
BAIL14SE00803AT 19
47918066 10/09/2015
23
INTRODUCTION
BAIL14SE00803AV 21
BAIL14SE00803AW 22
47918066 10/09/2015
24
INTRODUCTION
BAIL14SE00803AX 23
47918066 10/09/2015
25
INTRODUCTION
Special tools
The above recommendation, in order not to use improvi-
sation practices, is particularly important in the installation
of parts such as seals, bearings and bushings. For these
cases, it is essential to use devices such as those shown
alongside. The goal is to assemble these components in
an aligned manner and without causing deformation and
other damage.
For installation with a hammer, we suggest adopting a
standard extension (1) for use with the devices.
BAIL14SE00803AL 1
For installation in the press (2) , lay the rod of the press
directly on the device.
BAIL14SE00803AM 2
47918066 10/09/2015
26
INTRODUCTION
BAIL14SE00803BA 3
BAIL14SE00803BB 4
47918066 10/09/2015
27
INTRODUCTION
General specification
Specification / Model PS2045M
Number of rows x spacings 26 X 173 mm
Minimum required power 88 kW (120 Hp)
Seed box capacity 2,000 L ~ 1560 kg
(3439 lb)
Pasture box capacity (If 130 L
equipped)
Tires 16.9-28 TM 95 (8 ply)
Standard weight 6150 kg (13558 lb)
(approximately)
Recommended operating 4.0 - 8.0 km/h (2.5 -
speed 5.0 mph)
47918066 10/09/2015
28
INTRODUCTION
Dimension
Transport position
BAIL14SE00809FM 1
All dimensions in mm
47918066 10/09/2015
29
INTRODUCTION
BAIL14SE00809FN 2
All dimensions in mm
47918066 10/09/2015
30
INTRODUCTION
Working position
BAIL14SE00809GN 3
All dimensions in mm
47918066 10/09/2015
31
INTRODUCTION
General specification
The terms RIGHT SIDE (A) and LEFT SIDE (B) are deter-
mined from the point of view of the observer at the opera-
tor's position or behind the machine facing forward (mov-
ing direction).
BAIL14SE00824AD 1
47918066 10/09/2015
32
INTRODUCTION
Conversion factors
UNITS OF DISTANCE
To convert: In: Multiply by:
m cm 100
m mm 1000
m in 39.37
m feet 3.28
mm in 0.03937
mm cm 0.1
foot m 0.3048
foot cm 30.48
foot in 12
in cm 2.54
in mm 25.4
in m 0.0254
mile km 1.61
UNITS OF FORCE
To convert: In: Multiply by:
kgf N 9.81 (~10)
kgf ibf 2.204623
ibf kgf 0.4535924
ibf N 4.448222
UNITS OF TORQUE
To convert: In: Multiply by:
kgf.m N.m 9.81 (~10)
kgf.m lbf.foot 7.233003
kgf.m lbf.in 86.79621
N.m kgf.m 0.1
lbf.foot kgf.m 0.1382552
lbf.foot N.m 1.35582
lbf.in kgf.m 0.011521
lbf.in N.m 0.112984
UNITS OF VOLUME
To convert: In: Multiply by:
l cm³ 1000
l m³ 0.001
l in³ 61.02374
l foot³ 0.0353146
l gallon 0.264172
in³ l 0.016387
foot³ l 28.31685
gallon l 3.785412
ounce l 0.029573
UNITS OF MASS
To convert: In: Multiply by:
ton kg 1000
kg g 1000
kg lb 2.20462
lb kg 0.4535924
47918066 10/09/2015
33
INTRODUCTION
UNITS OF DENSITY
To convert: In: Multiply by:
kg/l g/l 1000
kg/m³ g/cm³ 0.001
g/cm³ kg/m³ 1000
g/cm³ lb/in³ 0.0361273
kg/m³ ib/foot³ 0.062427
kg/m³ ib/in³ 3.6127×10^-5
UNITS OF PRESSURE
To convert: In: Multiply by:
atm bar 1.01325
bar atm 0.9869233
gbar kgf/cm² 1.019716
kgf/cm² bar 0.980665
bar psi 14.50377
kgf/cm² psi 14.2233
psi bar 0.0689476
psi kgf/cm² 0.070307
UNITS OF POWER
To convert: In: Multiply by:
cv w 735.7
hp w 746.0
hp cv 1.014
cv hp 0.9863
kw cv 1.3592
kw hp 1.3404
47918066 10/09/2015
34
INTRODUCTION
Product identification
The frame number of the machine is engraved on the
frame (1) next to the drawbar hitch, on the right-hand side
of the machine.
BAIL14SE00824AE 1
BAIL14SE00801AL 2
47918066 10/09/2015
35
INTRODUCTION
Part identification
IDENTIFICATION AND DESCRIPTION OF COMPONENTS
BAIL14SE00824FA 1
The identification presented in this item below aims to set the identification standard for the main systems and com-
ponents throughout the manual:
47918066 10/09/2015
36
INTRODUCTION
Seed metering:
• The metering is carried out by the helical slotted rotor
system (1).
• The metering adjustment is carried out through the side
wheel (5) , which, by means of a spindle, moves the
square drive shaft (2) and the slotted rotors themselves
(1) laterally.
• The adjustment has the "tip" (4) as reference opposite
the ladder (3).
BAIL14SE00824AF 2
BAIL14SE00824AG 3
Transmission:
• The meters are driven by the two drive wheels through
chains (1) that transmit the movement of the drive wheel
to the seed metering shafts.
• Between wheels and metering shafts, the clutches (2)
shuts down the transmission automatically when lifting
the row units, during field limit maneuvers and trans-
port.
BAIL14SE00824AH 4
47918066 10/09/2015
37
INTRODUCTION
BAIL14SE00801AR 5
Definition of disks
• Double disk: they are disks of the same diameter, mounted on the same center.
• Offset double disk: they are disks of different diameters, mounted on the same center.
• Mismatched or offset double disk: they are disks of the same diameter, mounted on different centers.
• Mismatched and offset double disks: they are disks of different diameters, mounted on different centers.
BAIL14SE00801AT 6
47918066 10/09/2015
38
INTRODUCTION
Compaction
The NG press wheel (1) performs two operations at the
same time, the seed coverage and compaction.
The coverage is achieved through the return of moist soil
to the furrow. In this return, lateral compaction force is
exerted, eliminating possible air pockets around the seed.
BAIL14SE00801AV 8
BAIL14SE00824AJ 9
47918066 10/09/2015
39
INTRODUCTION
Frame:
• Robust monobloc type.
• The PS2045M frame differs depending on the transport
drive wheel system (3) with supports for links and arms.
• The frame is fitted with four-point hitch to lift, indicated
by arrows.
BAIL14SE00824AK 10
Drive wheel:
• Two articulated independent drive wheels.
• When to release the lock (1), the articulated arms are
left free to copy the soil, in order to avoid failure in the
transmission of the meters.
• During the transport, arms (2) should be secured by
connecting the lock (1) to the hitch (3) of the arms.
BAIL14SE00824AL 11
BAIL14SE00824AM 12
Box:
• In SEED version is made of carbon steel, with greater internal volume*.
*See General specification ().
47918066 10/09/2015
40
SERVICE MANUAL
Machine completion and equipment
PS2045 Mechanical
47918066 10/09/2015
05
Contents
47918066 10/09/2015
05
Machine completion and equipment - 05
PS2045 Mechanical
47918066 10/09/2015
05.1 [05.102] / 1
Contents
SERVICE
Machine completion
Service instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Transform A) PLACING THE MACHINE IN TRANSPORT MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Transform Transforming the machine to operation mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Transform Transforming the machine to transport mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pre-assemble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
47918066 10/09/2015
05.1 [05.102] / 2
Machine completion and equipment - Machine completion
47918066 10/09/2015
05.1 [05.102] / 3
Machine completion and equipment - Machine completion
BAIL14SE00820AB 1
BAIL14SE00820AC 2
BAIL14SE00820AD 3
9. After applying the parking brake, lock the lever (3) with
the pin (10) , preventing accidental disengagement of
the brake from occurring.
BAIL14SE00820AE 4
47918066 10/09/2015
05.1 [05.102] / 4
Machine completion and equipment - Machine completion
BAIL14SE00820AF 5
47918066 10/09/2015
05.1 [05.102] / 5
Machine completion and equipment - Machine completion
BAIL14SE00820AG 1
BAIL14SE00820AI 2
BAIL14SE00820AJ 3
47918066 10/09/2015
05.1 [05.102] / 6
Machine completion and equipment - Machine completion
BAIL14SE00820AK 4
NOTE: During the turning of the machine, the arm (6) is positioned for engagement by the rod (7) .
10. During machine movement the locking hook (8) must
remain in the position shown.
BAIL14SE00820AL 5
11. After full seating of the beam (4) in the fork (6) of the
auxiliary arm, by the action of the hydraulic cylinder
(5) , the locking hook (8) descends by gravity, making
the retention of the beam (4) .
BAIL14SE00820AM 6
BAIL14SE00820AN 7
47918066 10/09/2015
05.1 [05.102] / 7
Machine completion and equipment - Machine completion
NOTE: After making the change from Transport to Operation, verify full seating of the drawbar beam (4) in the arm
fork (6) and also the correct locking of the hook (8) . Refer to item 10.4 on the possible settings.
13. The machine is ready for operation.
47918066 10/09/2015
05.1 [05.102] / 8
Machine completion and equipment - Machine completion
BAIL14SE00820AO 1
BAIL14SE00820AP 2
BAIL14SE00820AQ 3
47918066 10/09/2015
05.1 [05.102] / 9
Machine completion and equipment - Machine completion
BAIL14SE00820AR 4
BAIL14SE00820AS 5
NOTE: During the turning of the machine, the arm (6) is returned to home position by the rod (7) .
NOTE: Operate the remote control carefully, disengaging the drawbar beam (4) from the end of the auxiliary arm (6) .
14. The lock (3) must remain in the position shown.
15. Continue actuating the remote control to fit the beam
(4) in the chassis receptacle (9.)
16. After the full seating of the beam (4) in the recepta-
cle (9) of the machine chassis by the action of the hy-
draulic cylinder (5) , the lock (3) descends by gravity,
making the retention of the beam (4) in the machine
frame.
BAIL14SE00820AT 6
BAIL14SE00820AU 7
47918066 10/09/2015
05.1 [05.102] / 10
Machine completion and equipment - Machine completion
BAIL14SE00820AH 8
47918066 10/09/2015
05.1 [05.102] / 11
Machine completion and equipment - Machine completion
BAIL14SE00820AW 2
BAIL14SE00820AX 3
47918066 10/09/2015
05.1 [05.102] / 12
Machine completion and equipment - Machine completion
BAIL14SE00820AZ 5
17. To adjust:
18. Disconnect the rod end (6a) , removing pin (6b) .
19. Rotate the rod end (6a) as necessary.
NOTE: If necessary, lock the rotation of the cylinder rod
(6) with an appropriate spanner, in the recesses for this
purpose.
20. Connect the rod end again and test operation.
ATTENTION: Always remember to remove people, ani-
mals and obstacles when moving the machine or drawbar.
BAIL14SE00821AA 6
BAIL14SE00821AB 7
47918066 10/09/2015
05.1 [05.102] / 13
Index
47918066 10/09/2015
05.1 [05.102] / 14
47918066 10/09/2015
05.1 [05.102] / 15
CNH Industrial Italia S.p.A. viale delle Nazioni, 55 Modena Italy 41122
All rights reserved. No part of the text or illustrations of this publication may be reproduced.
NEW HOLLAND policy is one of continuous improvement and the right to change prices, specification or equipment
at any time without notices is reserved.
All data given in this publication is subject to production variations. Dimensions and weight are approximate only and
the illustrations do not necessarily show products in standard condition. For exact information about any particular
product, please consult your NEW HOLLAND Dealer.
47918066 10/09/2015
EN
SERVICE MANUAL
Brakes and controls
PS2045 Mechanical
47918066 10/09/2015
33
Contents
47918066 10/09/2015
33
Brakes and controls - 33
PS2045 Mechanical
47918066 10/09/2015
33.1 [33.220] / 1
Contents
FUNCTIONAL DATA
47918066 10/09/2015
33.1 [33.220] / 2
Brakes and controls - Trailer brake hydraulic control
BAIL14SE00821GA 1
SYSTEM PRESENTATION
NOTE: Key valid for all the figures in this chapter:
47918066 10/09/2015
33.1 [33.220] / 3
Brakes and controls - Trailer brake hydraulic control
Cylinders:
BAIL14SE00821AJ 2
Hoses:
47918066 10/09/2015
33.1 [33.220] / 4
Brakes and controls - Trailer brake hydraulic control
SYSTEM OPERATION
Normal operation:
This flow passes through the valve (3) directly to the cylin-
ders ( (C1) and (C2) )through hoses (M4) , (M5) and (M6)
.
The cord (2) connects the valve lever (6) with tractor.
tor occurs, the cord is pulled rotating the lever (6) , which
then is released from the valve shaft (3) .
BAIL14SE00821AL 2
BAIL14SE00821AM 3
47918066 10/09/2015
33.1 [33.220] / 5
Brakes and controls - Trailer brake hydraulic control
Move the lever (8) to the right of the machine until you get
a firm brake application.
Lock the trigger (9) in the mechanism and install pin (12)
, ensuring that the parking brake does not disarm.
BAIL14SE00821AN 4
The rod of the cylinder (C) cedes, allowing the rod (10) to
rotate the lever (11) .
BAIL14SE00821AO 5
BAIL14SE00821AP 6
47918066 10/09/2015
33.1 [33.220] / 6
Index
47918066 10/09/2015
33.1 [33.220] / 7
CNH Industrial Italia S.p.A. viale delle Nazioni, 55 Modena Italy 41122
All rights reserved. No part of the text or illustrations of this publication may be reproduced.
NEW HOLLAND policy is one of continuous improvement and the right to change prices, specification or equipment
at any time without notices is reserved.
All data given in this publication is subject to production variations. Dimensions and weight are approximate only and
the illustrations do not necessarily show products in standard condition. For exact information about any particular
product, please consult your NEW HOLLAND Dealer.
47918066 10/09/2015
EN
SERVICE MANUAL
Hydraulic systems
PS2045 Mechanical
47918066 10/09/2015
35
Contents
Hydraulic systems - 35
47918066 10/09/2015
35
Hydraulic systems - 35
PS2045 Mechanical
47918066 10/09/2015
35.1 [35.162] / 1
Contents
Hydraulic systems - 35
FUNCTIONAL DATA
SERVICE
47918066 10/09/2015
35.1 [35.162] / 2
Hydraulic systems - Front hitch cylinders and lines
IDENTIFICATION OF COMPONENTS
BAIL14SE00831FA 1
47918066 10/09/2015
35.1 [35.162] / 3
Hydraulic systems - Front hitch cylinders and lines
8. Remove the back cover (2) and ahead, pull the rod assy
(13) with the piston (11) , front cover (17) and rod end
(20) .
9. Hold the rod (13) in the flat recesses indicated by the
arrow, using a wrench or a press.
NOTE: Be careful not to damage the surface of the rod!
10. Loosen lock nut (19) and remove the rod end (20) .
11. Remove the cotter pin (5) and the nut (6) secure the
piston to the rod.
12. Remove the other components and discard the seal-
ing material. BAIL14SE00831AC 2
NOTE: For general information about maintenance of cylinders, see chapter 9.6.
BAIL14SE00831EC 3
47918066 10/09/2015
35.1 [35.162] / 4
Hydraulic systems - Front hitch cylinders and lines
47918066 10/09/2015
35.1 [35.162] / 5
Index
Hydraulic systems - 35
47918066 10/09/2015
35.1 [35.162] / 6
Hydraulic systems - 35
PS2045 Mechanical
47918066 10/09/2015
35.2 [35.353] / 1
Contents
Hydraulic systems - 35
FUNCTIONAL DATA
SERVICE
47918066 10/09/2015
35.2 [35.353] / 2
Hydraulic systems - Hydraulic travel system
IDENTIFICATION OF COMPONENTS
BAIL14SE00831FB 1
47918066 10/09/2015
35.2 [35.353] / 3
Hydraulic systems - Hydraulic travel system
47918066 10/09/2015
35.2 [35.353] / 4
Hydraulic systems - Hydraulic travel system
BAIL14SE00831AE 2
47918066 10/09/2015
35.2 [35.353] / 5
Hydraulic systems - Hydraulic travel system
BAIL14SE00831AF 1
4. Remove the pins (20) and (21) and remove the cylinder
from the machine.
5. Clean the cylinder assembly and place it on the bench.
6. Remove the front cap (16) . For this, use a similar tool
to the illustrated side, which will also apply the correct
torque on the cap, in the assembly.
7. Pull the cap assembly (16) and rod (17) with the piston
(5) and seals out of the cylinder.
BAIL14SE00831AG 2
BAIL14SE00831ED 3
47918066 10/09/2015
35.2 [35.353] / 6
Hydraulic systems - Hydraulic travel system
BAIL14SE00831FC 4
47918066 10/09/2015
35.2 [35.353] / 7
Hydraulic systems - Hydraulic travel system
47918066 10/09/2015
35.2 [35.353] / 8
Hydraulic systems - Hydraulic travel system
CLEANLINESS
• Soon after disconnecting cylinders, protect hoses
and the galleries with adequate caps to prevent the
entry of dirt and water
• Before disassembling hydraulic cylinders, make an
external cleaning of them.
• Do all the maintenance work in clean benches sep-
arate from other activities of the workshop.
• When leaving cylinder disassembled for some time,
cover them to protect against dust.
Furthermore, apply oil on the parts as into housings,
pistons and rods, to prevent oxidation.
• Use suitable tools: improvisations cause damage to
parts and can unusable them.
Small scratches into housing, for example, compro-
mise the sealing.
REPAIR TECHNIQUES
After disassembling a cylinder for service
• Clean all parts in diesel oil or kerosene. Dry with
compressed air, using eye protection.
• Application of ultra fine sandpaper and polishing
cloth inside the housing, with the goal of removing
slight signs of rust or surface scratches. Deep
scratches determine the housing replacement.
• Replacement of the repairs: disassembly and re-
assembly for the replacement of items of the repair
kit is described in specific chapters in this section for
each machine's hydraulic cylinder.
• Features such as chrome bath, grinding and polish-
ing, can be made, but require highly specialized re-
sources.
47918066 10/09/2015
35.2 [35.353] / 9
Hydraulic systems - Hydraulic travel system
BAIL14SE00831BE 1
47918066 10/09/2015
35.2 [35.353] / 10
Index
Hydraulic systems - 35
47918066 10/09/2015
35.2 [35.353] / 11
CNH Industrial Italia S.p.A. viale delle Nazioni, 55 Modena Italy 41122
All rights reserved. No part of the text or illustrations of this publication may be reproduced.
NEW HOLLAND policy is one of continuous improvement and the right to change prices, specification or equipment
at any time without notices is reserved.
All data given in this publication is subject to production variations. Dimensions and weight are approximate only and
the illustrations do not necessarily show products in standard condition. For exact information about any particular
product, please consult your NEW HOLLAND Dealer.
47918066 10/09/2015
EN
SERVICE MANUAL
Hitches, drawbars, and implement couplings
PS2045 Mechanical
47918066 10/09/2015
37
Contents
47918066 10/09/2015
37
Hitches, drawbars, and implement couplings - 37
PS2045 Mechanical
47918066 10/09/2015
37.1 [37.100] / 1
Contents
FUNCTIONAL DATA
SERVICE
47918066 10/09/2015
37.1 [37.100] / 2
Hitches, drawbars, and implement couplings - Drawbars and towing hitches
BAIL14SE00826FA 1
BAIL14SE00826AA 2
NOTE: *Refer to Section 10 about the drawbar system and transport drive wheel.
47918066 10/09/2015
37.1 [37.100] / 3
Hitches, drawbars, and implement couplings - Drawbars and towing hitches
BAIL14SE00826AE 2
47918066 10/09/2015
37.1 [37.100] / 4
Hitches, drawbars, and implement couplings - Drawbars and towing hitches
BAIL14SE00826AF 3
BAIL14SE00826AG 4
47918066 10/09/2015
37.1 [37.100] / 5
Hitches, drawbars, and implement couplings - Drawbars and towing hitches
47918066 10/09/2015
37.1 [37.100] / 6
Hitches, drawbars, and implement couplings - Drawbars and towing hitches
BAIL14SE00826AH 2
GENERAL REPAIRS
For repairs to structural components, welding, straight-
ening and repainting, apply the same principles rec-
ommended for the chassis; refer to Frame - Repair
(39.100).
47918066 10/09/2015
37.1 [37.100] / 7
Index
47918066 10/09/2015
37.1 [37.100] / 8
47918066 10/09/2015
37.1 [37.100] / 9
CNH Industrial Italia S.p.A. viale delle Nazioni, 55 Modena Italy 41122
All rights reserved. No part of the text or illustrations of this publication may be reproduced.
NEW HOLLAND policy is one of continuous improvement and the right to change prices, specification or equipment
at any time without notices is reserved.
All data given in this publication is subject to production variations. Dimensions and weight are approximate only and
the illustrations do not necessarily show products in standard condition. For exact information about any particular
product, please consult your NEW HOLLAND Dealer.
47918066 10/09/2015
EN
SERVICE MANUAL
Frames and ballasting
PS2045 Mechanical
47918066 10/09/2015
39
Contents
47918066 10/09/2015
39
Frames and ballasting - 39
Frame - 100
PS2045 Mechanical
47918066 10/09/2015
39.1 [39.100] / 1
Contents
Frame - 100
FUNCTIONAL DATA
Frame
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Frame leveling support
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SERVICE
Frame
Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Frame leveling support
Remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
47918066 10/09/2015
39.1 [39.100] / 2
Frames and ballasting - Frame
Frame - Overview
BAIL14SE00825FA 1
BAIL14SE00825AA 2 BAIL14SE00825AB 3
The frame of the PS2045M equipped with transport wheel drives (4), consists of the elements of the figure above.
The monobloc-type frame, has three longitudinal ribs (6), providing the necessary structural rigidity.
The toolholder bar function is fulfilled by the beam (5), where all the claws (7) of the row units are attached on.
The machine's rear support is provided by the drive wheels and, in the event of their removal, it is necessary to block
the machine under the frame in a convenient way.
47918066 10/09/2015
39.1 [39.100] / 3
Frames and ballasting - Frame
BAIL14SE00826AI 1 BAIL14SE00826AJ 2
Items Description
1 Support stand.
2 Foot retaining pin (anti-fall).
3 Support stand positioning lock pin.
4 Support.
5 Bolts, nuts and washers for fixing the support on the frame toolholder bar (6).
47918066 10/09/2015
39.1 [39.100] / 4
Frames and ballasting - Frame
Frame - Repair
Because it is a structural part, which is not usually re-
placed, minor repairs become necessary, such as:
Straightening
This practice is possible, except in the main compo-
nents, such as stringers (tubes) and structural plates.
To straighten components, heat them using a blow-
torch.
Welding
Cracks or breaks may be welded to recover its strength
characteristics. Observe the related safety precautions
listed in Section 1.
BAIL14SE00495AA 1
Refinishing
After repairs such as those cited above, it is necessary
to sand the affected parts and do the refinishing.
ATTENTION: Replace the safety labels and instructions in
case of refinishing or when they suffer damage.
BAIL14SE00496AA 2
47918066 10/09/2015
39.1 [39.100] / 5
Frames and ballasting - Frame
BAIL14SE00826AJ 1
47918066 10/09/2015
39.1 [39.100] / 6
Frames and ballasting - Frame
47918066 10/09/2015
39.1 [39.100] / 7
Index
Frame - 100
Frame - Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Frame - Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Frame leveling support - Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Frame leveling support - Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Frame leveling support - Remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
47918066 10/09/2015
39.1 [39.100] / 8
Frames and ballasting - 39
PS2045 Mechanical
47918066 10/09/2015
39.2 [39.140] / 1
Contents
FUNCTIONAL DATA
Counterweight
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
47918066 10/09/2015
39.2 [39.140] / 2
Frames and ballasting - Ballasts and supports
Counterweight - Overview
COUNTERWEIGHTS (OPTIONAL)
The weights (1), when used, are introduced into the rear
beam of the frame.
The weights are kept aligned in the beam through the bar
(2) and the retention in the ends is made through the pins
(3).
BAIL14SE00826AB 1
BAIL14SE00493AA 2
47918066 10/09/2015
39.2 [39.140] / 3
Index
47918066 10/09/2015
39.2 [39.140] / 4
47918066 10/09/2015
39.2 [39.140] / 5
CNH Industrial Italia S.p.A. viale delle Nazioni, 55 Modena Italy 41122
All rights reserved. No part of the text or illustrations of this publication may be reproduced.
NEW HOLLAND policy is one of continuous improvement and the right to change prices, specification or equipment
at any time without notices is reserved.
All data given in this publication is subject to production variations. Dimensions and weight are approximate only and
the illustrations do not necessarily show products in standard condition. For exact information about any particular
product, please consult your NEW HOLLAND Dealer.
47918066 10/09/2015
EN
SERVICE MANUAL
Wheels
PS2045 Mechanical
47918066 10/09/2015
44
Contents
Wheels - 44
47918066 10/09/2015
44
Wheels - 44
PS2045 Mechanical
47918066 10/09/2015
44.1 [44.530] / 1
Contents
Wheels - 44
FUNCTIONAL DATA
Transport wheel
Axle - Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Carrying and transport wheel supports
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SERVICE
47918066 10/09/2015
44.1 [44.530] / 2
Wheels - Carrying and transport wheels
BAIL14SE00827FA 1
47918066 10/09/2015
44.1 [44.530] / 3
Wheels - Carrying and transport wheels
BAIL14SE00827GC 1
The figure shows the drive wheel on the right side
47918066 10/09/2015
44.1 [44.530] / 4
Wheels - Carrying and transport wheels
BAIL14SE00827FC 2
BAIL14SE00827AI 3
47918066 10/09/2015
44.1 [44.530] / 5
Wheels - Carrying and transport wheels
47918066 10/09/2015
44.1 [44.530] / 6
Wheels - Carrying and transport wheels
BAIL14SE00819AE 1
BAIL14SE00819AD 2
47918066 10/09/2015
44.1 [44.530] / 7
Wheels - Carrying and transport wheels
BAIL14SE00827AA 1
BAIL14SE00827AB 2
BAIL14SE00827AC 3
47918066 10/09/2015
44.1 [44.530] / 8
Wheels - Carrying and transport wheels
13. Remove the cotter pin (4), the castle nut (5) and
washer (6).
14. Remove the nuts (9) and bolts (14) that join the hub
(10) with the extension (13).
15. Remove the hub (10). If necessary, use a hammer.
16. Remove the remaining components of the hub as
needed.
47918066 10/09/2015
44.1 [44.530] / 9
Wheels - Carrying and transport wheels
BAIL14SE00819AF 1
BAIL14SE00819AG 2
BAIL14SE00819ADH 3
BAIL14SE00819AI 4
47918066 10/09/2015
44.1 [44.530] / 10
Wheels - Carrying and transport wheels
12. Install the bolts (14) and self-lock nuts (9) that join the
extension (13) with the hub (10).
13. Tighten the nuts alternately and in stages.
BAIL14SE00819AJ 5
BAIL14SE00819AK 6
BAIL14SE00827FB 7
47918066 10/09/2015
44.1 [44.530] / 11
Wheels - Carrying and transport wheels
15. On the shaft, install the smaller bearing cone (7), until
the full settlement on the respective cup, previously
installed on the hub (10).
16. Then, install the washer (6) and the castle nut (5).
BAIL14SE00819AL 8
23. Install a new gasket (3) and reinstall the hub cap (2).
BAIL14SE00819AN 10
24. Install the bolts (1), but do not apply tightening for now.
25. Grease the grease fitting of hub cap (2), until the
grease begins to seep under the cap (through the gas-
ket), indicating that the housing is full.
26. Now, tighten bolts (1) alternately and in stages, to pre-
vent the warping of the cap.
BAIL14SE00819AO 11
47918066 10/09/2015
44.1 [44.530] / 12
Wheels - Carrying and transport wheels
BAIL14SE00827AH 13
47918066 10/09/2015
44.1 [44.530] / 13
Wheels - Carrying and transport wheels
BAIL14SE00827AJ 1
BAIL14SE00827AK 2
BAIL14SE00827AL 3
7. Remove the lock pin (17) and the large gear (12) of the
hex shaft.
BAIL14SE00827AM 4
47918066 10/09/2015
44.1 [44.530] / 14
Wheels - Carrying and transport wheels
11. With the weight of the arm (3) suspended by the lifting
device, remove the tubular shaft (11).
For this, use a hammer and a brass pin. Do not tap
directly on the shaft, as this may cause deformation of
the same.
12. After removing the shaft (11), remove the arm from the
frame.
BAIL14SE00827AO 6
47918066 10/09/2015
44.1 [44.530] / 15
Wheels - Carrying and transport wheels
BAIL14SE00827AP 1
47918066 10/09/2015
44.1 [44.530] / 16
Wheels - Carrying and transport wheels
BAIL14SE00827FE 1
47918066 10/09/2015
44.1 [44.530] / 17
Wheels - Carrying and transport wheels
BAIL14SE00821FA 1
BAIL14SE00821FC 2
47918066 10/09/2015
44.1 [44.530] / 18
Wheels - Carrying and transport wheels
BAIL14SE00821BA 3
NOTE: About maintenance of the hydraulic system, see Section 8 of this manual.
NOTE: Key valid for all figures in this section:
47918066 10/09/2015
44.1 [44.530] / 19
Wheels - Carrying and transport wheels
BAIL14SE00821AC 1
BAIL14SE00821AD 2
BAIL14SE00821AE 3
47918066 10/09/2015
44.1 [44.530] / 20
Wheels - Carrying and transport wheels
BAIL14SE00821AF 4
BAIL14SE00821AH 5
47918066 10/09/2015
44.1 [44.530] / 21
Wheels - Carrying and transport wheels
BAIL14SE00821BB 2
47918066 10/09/2015
44.1 [44.530] / 22
Index
Wheels - 44
47918066 10/09/2015
44.1 [44.530] / 23
CNH Industrial Italia S.p.A. viale delle Nazioni, 55 Modena Italy 41122
All rights reserved. No part of the text or illustrations of this publication may be reproduced.
NEW HOLLAND policy is one of continuous improvement and the right to change prices, specification or equipment
at any time without notices is reserved.
All data given in this publication is subject to production variations. Dimensions and weight are approximate only and
the illustrations do not necessarily show products in standard condition. For exact information about any particular
product, please consult your NEW HOLLAND Dealer.
47918066 10/09/2015
EN
SERVICE MANUAL
Electrical systems
PS2045 Mechanical
47918066 10/09/2015
55
Contents
Electrical systems - 55
47918066 10/09/2015
55
Electrical systems - 55
PS2045 Mechanical
47918066 10/09/2015
55.1 [55.036] / 1
Contents
Electrical systems - 55
FUNCTIONAL DATA
SERVICE
47918066 10/09/2015
55.1 [55.036] / 2
Electrical systems - Hydraulic system control
BAIL14SE00907GA 1
47918066 10/09/2015
55.1 [55.036] / 3
Electrical systems - Hydraulic system control
BAIL14SE00907AA 2 BAIL14SE00907AB 3
BAIL14SE00907AC 4 BAIL14SE00832AL 5
Disassembled connectors: repairs require special
tooling.
47918066 10/09/2015
55.1 [55.036] / 4
Electrical systems - Hydraulic system control
47918066 10/09/2015
55.1 [55.036] / 5
Electrical systems - Hydraulic system control
BAIL14SE00907AC 2
BAIL14SE00907AB 4
47918066 10/09/2015
55.1 [55.036] / 6
Electrical systems - Hydraulic system control
47918066 10/09/2015
55.1 [55.036] / 7
Index
Electrical systems - 55
47918066 10/09/2015
55.1 [55.036] / 8
Electrical systems - 55
PS2045 Mechanical
47918066 10/09/2015
55.2 [55.404] / 1
Contents
Electrical systems - 55
SERVICE
47918066 10/09/2015
55.2 [55.404] / 2
Electrical systems - External lighting
BAIL14SE00725AA 1
BAIL14SE00726AA 2
BAIL14SE00727AA 3
47918066 10/09/2015
55.2 [55.404] / 3
Electrical systems - External lighting
BAIL14SE00728AA 4
47918066 10/09/2015
55.2 [55.404] / 4
Electrical systems - External lighting
BAIL14SE00731AA 2
47918066 10/09/2015
55.2 [55.404] / 5
Electrical systems - External lighting
Script Check:
1. Make sure there are no problems in the tractor's
electrical circuit.
NOTE: The fuses that protect this circuit are lo-
cated in the electrical panel of the tractor.
2. Do a quick check for the integrity of the electrical
components, connections, cables and previously
identified connectors.
3. Check for (a) burned lamp(s): replace it (them) if
applicable, following the previous procedure.
4. Check the circuit of the ground cable (black).
5. Detailed checking of wiring harnesses: check them
for apparent damage or defects, such as:
○ Signs of kneading of the harness or cables.
○ Breakage of cables (circuit "open", interrupted).
○ Breakage or excoriation of harness protections
(conduits).
○ Signs of deterioration in harnesses and compo-
nents, caused for example by incorrect machine
storage
○ Routing and fastening of cables: when making a
diagnosis, check the harness in its cable routes
and attachment points. Keep plastic clamps al-
ways handy to fix or redo attachments.
Connectors check
Open the connectors and check them for:
• Rusty contacts: When this defect occurs, it is com-
mon for the system to work again after disconnecting
and reconnecting a plug in the socket.
• Rusty contacts cause high resistance in the circuit
and the consequent malfunction.
• In this case, clean the contacts.
• There are spray products (aerosol) specific for this
purpose.
• Broken or warped contacts: If necessary, replace the
plug and socket assy.
BAIL14SE00832AL 4
• In the case of 10 mm Sindal connectors (3) - figure
above, make sure the lid (3a) of the box is properly
fitted and sealed.
47918066 10/09/2015
55.2 [55.404] / 6
Electrical systems - External lighting
BAIL14SE00907FA 5
Identification of the box connections (3):
47918066 10/09/2015
55.2 [55.404] / 7
Index
Electrical systems - 55
47918066 10/09/2015
55.2 [55.404] / 8
47918066 10/09/2015
55.2 [55.404] / 9
CNH Industrial Italia S.p.A. viale delle Nazioni, 55 Modena Italy 41122
All rights reserved. No part of the text or illustrations of this publication may be reproduced.
NEW HOLLAND policy is one of continuous improvement and the right to change prices, specification or equipment
at any time without notices is reserved.
All data given in this publication is subject to production variations. Dimensions and weight are approximate only and
the illustrations do not necessarily show products in standard condition. For exact information about any particular
product, please consult your NEW HOLLAND Dealer.
47918066 10/09/2015
EN
SERVICE MANUAL
Metering system
PS2045 Mechanical
47918066 10/09/2015
61
Contents
Metering system - 61
47918066 10/09/2015
61
Metering system - 61
PS2045 Mechanical
47918066 10/09/2015
61.1 [61.901] / 1
Contents
Metering system - 61
FUNCTIONAL DATA
SERVICE
47918066 10/09/2015
61.1 [61.901] / 2
Metering system - Metering mechanical drive
BAIL14SE00828FA 1
The figure above represents the complete transmission system of the seed meters, from the wheel gear (1) to the
final gear (10) of the square shaft of the meters.
The clutch (5) disconnect the transmission to meters when raise the row units.
• From wheel hub and gear (1), the chain (2) transfers
the movement to the gear and shaft (3) located on the
front (joint) arm of the drive wheels.
• The gear and the chain (4) drive the clutch gear (5).
• When the clutch (5) is coupled (rows lowered), the
movement is transferred to the shaft (6) of general
drive.
• The gear and the chain (7) drive the clutch and idle
gears (8).
• The smaller gear (8) drives the gear (10) of the square
shaft of seed meters through chain (9).
• The smaller gear of the pair (11) drives the meters of BAIL14SE00828AA 2
the pasture seed box, if equipped.
47918066 10/09/2015
61.1 [61.901] / 3
Metering system - Metering mechanical drive
BAIL14SE00828FB 3
BAIL14SE00828FC 4
47918066 10/09/2015
61.1 [61.901] / 4
Metering system - Metering mechanical drive
BAIL14SE00828FD 1
47918066 10/09/2015
61.1 [61.901] / 5
Metering system - Metering mechanical drive
This control is done by the moving rod (22) and the outer
arm (13).
The upper end of the rod (12) has a slot (R) that allows
to reposition it, to change the action adjust of the clutch:
turning on/off sooner or later.
BAIL14SE00828AC 2
BAIL14SE00828AD 3
BAIL14SE00828AE 4
47918066 10/09/2015
61.1 [61.901] / 6
Metering system - Metering mechanical drive
BAIL14SE00828GB 1
47918066 10/09/2015
61.1 [61.901] / 7
Metering system - Metering mechanical drive
(M3) Bearing of the final idle gear of the seed drives the
seed meters.
BAIL14SE00828AM 2
BAIL14SE00828AN 3
47918066 10/09/2015
61.1 [61.901] / 8
Metering system - Metering mechanical drive
BAIL14SE00828AF 1
BAIL14SE00828AG 2
47918066 10/09/2015
61.1 [61.901] / 9
Metering system - Metering mechanical drive
BAIL14SE00828AJ 3
47918066 10/09/2015
61.1 [61.901] / 10
Metering system - Metering mechanical drive
BAIL14SE00828FD 4
47918066 10/09/2015
61.1 [61.901] / 11
Metering system - Metering mechanical drive
BAIL14SE00828BA 1
BAIL14SE00828AK 3
47918066 10/09/2015
61.1 [61.901] / 12
Metering system - Metering mechanical drive
47918066 10/09/2015
61.1 [61.901] / 13
Metering system - Metering mechanical drive
47918066 10/09/2015
61.1 [61.901] / 14
Metering system - Metering mechanical drive
BAIL14SE00828GA 1
47918066 10/09/2015
61.1 [61.901] / 15
Metering system - Metering mechanical drive
47918066 10/09/2015
61.1 [61.901] / 16
Metering system - Metering mechanical drive
BAIL14SE00828FE 1
47918066 10/09/2015
61.1 [61.901] / 17
Metering system - Metering mechanical drive
BAIL14SE00828AQ 3
47918066 10/09/2015
61.1 [61.901] / 18
Index
Metering system - 61
47918066 10/09/2015
61.1 [61.901] / 19
CNH Industrial Italia S.p.A. viale delle Nazioni, 55 Modena Italy 41122
All rights reserved. No part of the text or illustrations of this publication may be reproduced.
NEW HOLLAND policy is one of continuous improvement and the right to change prices, specification or equipment
at any time without notices is reserved.
All data given in this publication is subject to production variations. Dimensions and weight are approximate only and
the illustrations do not necessarily show products in standard condition. For exact information about any particular
product, please consult your NEW HOLLAND Dealer.
47918066 10/09/2015
EN
SERVICE MANUAL
Soil preparation/Finishing
PS2045 Mechanical
47918066 10/09/2015
75
Contents
Soil preparation/Finishing - 75
47918066 10/09/2015
75
Soil preparation/Finishing - 75
PS2045 Mechanical
47918066 10/09/2015
75.1 [75.200] / 1
Contents
Soil preparation/Finishing - 75
FUNCTIONAL DATA
Tool support
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SERVICE
Tool support
Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Disassemble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Visual inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Assemble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
47918066 10/09/2015
75.1 [75.200] / 2
Soil preparation/Finishing - Ground-engaging components
BAIL14SE00785GA 1
47918066 10/09/2015
75.1 [75.200] / 3
Soil preparation/Finishing - Ground-engaging components
47918066 10/09/2015
75.1 [75.200] / 4
Soil preparation/Finishing - Ground-engaging components
BAIL14SE00778FA 1
47918066 10/09/2015
75.1 [75.200] / 5
Soil preparation/Finishing - Ground-engaging components
BAIL14SE00634AA 3
BAIL14SE00827AC 4
BAIL14SE00636AA 5
BAIL14SE00637AA 6
47918066 10/09/2015
75.1 [75.200] / 6
Soil preparation/Finishing - Ground-engaging components
BAIL14SE00738BA 7
47918066 10/09/2015
75.1 [75.200] / 7
Soil preparation/Finishing - Ground-engaging components
BAIL14SE00638AA 8
BAIL14SE00639AA 9
BAIL14SE00640AA 10
47918066 10/09/2015
75.1 [75.200] / 8
Soil preparation/Finishing - Ground-engaging components
BAIL14SE00827BB 11
SPACING INFORMATION
The PS2045M is normally equipped with 26 row units
with a spacing of 173.0 mm (6.8 in)
1. For updated information, always consult the operator's
manual.
BAIL14SE00642AA 12
BAIL14SE00827AD 13
47918066 10/09/2015
75.1 [75.200] / 9
Soil preparation/Finishing - Ground-engaging components
NOTE: The spacing of 173.0 mm (6.8 in) is ensured by fitting shims (2) together with spacers (1).
47918066 10/09/2015
75.1 [75.200] / 10
Soil preparation/Finishing - Ground-engaging components
BAIL14SE00827HA 14
47918066 10/09/2015
75.1 [75.200] / 11
Soil preparation/Finishing - Ground-engaging components
BAIL14SE00643AA 1
2. Remove the cotter pin (18) and pin (16) , releasing the
spring assembly (15).
3. Remove the springs support (17) by loosening nuts (13)
and clip (8).
BAIL14SE00644AA 2
4. Loosen nut (3) and remove pin (2) releasing the arm
(4).
5. Remove the arm (4) of the planter.
BAIL14SE00645AA 3
47918066 10/09/2015
75.1 [75.200] / 12
Soil preparation/Finishing - Ground-engaging components
BAIL14SE00646AA 4
Spring assembly
10. Disengage the spring assembly (15) from the spring
grip (29) .
11. Remove the cotter pin (27) the upper stopper (26) and
the upper guide (25).
12. Remove the springs: outer (24) intermediate (23) and
inner (22).
BAIL14SE00647AA 5
13. Remove the lower guide (21) and the lower stopper
(20).
BAIL14SE00648AA 6
BAIL14SE00649AA 7
47918066 10/09/2015
75.1 [75.200] / 13
Soil preparation/Finishing - Ground-engaging components
BAIL14SE00650AA 1
47918066 10/09/2015
75.1 [75.200] / 14
Soil preparation/Finishing - Ground-engaging components
BAIL14SE00651AA 1
BAIL14SE00652AA 2
BAIL14SE00747CA 3
BAIL14SE00748CA 4
47918066 10/09/2015
75.1 [75.200] / 15
Index
Soil preparation/Finishing - 75
47918066 10/09/2015
75.1 [75.200] / 16
47918066 10/09/2015
75.1 [75.200] / 17
CNH Industrial Italia S.p.A. viale delle Nazioni, 55 Modena Italy 41122
All rights reserved. No part of the text or illustrations of this publication may be reproduced.
NEW HOLLAND policy is one of continuous improvement and the right to change prices, specification or equipment
at any time without notices is reserved.
All data given in this publication is subject to production variations. Dimensions and weight are approximate only and
the illustrations do not necessarily show products in standard condition. For exact information about any particular
product, please consult your NEW HOLLAND Dealer.
47918066 10/09/2015
EN
SERVICE MANUAL
Seeding
PS2045 Mechanical
47918066 10/09/2015
77
Contents
Seeding - 77
47918066 10/09/2015
77
Seeding - 77
PS2045 Mechanical
47918066 10/09/2015
77.1 [77.100] / 1
Contents
Seeding - 77
FUNCTIONAL DATA
Drive shaft
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Tank
Overview Seed tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Overview Pasture box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SERVICE
Drive shaft
Remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Tank
Remove Seed tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Assemble Seed tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Disassemble Seed tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Visual inspection Seed tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Emptying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Adjust Pasture box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
47918066 10/09/2015
77.1 [77.100] / 2
Seeding - Product handling and delivery drive system
BAIL14SE00825FB 1
BAIL15SE00825AC 2 BAIL14SE00498AA 3
NOTE: This assembly features some differences between machine models, but only in quantity of components and
length of square shaft.
47918066 10/09/2015
77.1 [77.100] / 3
Seeding - Product handling and delivery drive system
47918066 10/09/2015
77.1 [77.100] / 4
Seeding - Product handling and delivery drive system
The seed box is made with steel plates, with a simple and
robust frame which can be easily removed from the main
frame thoroughly.
Each part of the box has a lid (1) and a structural rein-
forcement plate (8).
BAIL14SE00900AA 1
BAIL14SE00900AB 2
47918066 10/09/2015
77.1 [77.100] / 5
Seeding - Product handling and delivery drive system
BAIL14SE00900GA 3
47918066 10/09/2015
77.1 [77.100] / 6
Seeding - Product handling and delivery drive system
BAIL14SE00900FA 1
BAIL14SE00900FC 2
47918066 10/09/2015
77.1 [77.100] / 7
Seeding - Product handling and delivery drive system
47918066 10/09/2015
77.1 [77.100] / 8
Seeding - Product handling and delivery drive system
BAIL15SE00825AD 1
BAIL15SE00825AE 2
47918066 10/09/2015
77.1 [77.100] / 9
Seeding - Product handling and delivery drive system
BAIL15SE00825AH 5
47918066 10/09/2015
77.1 [77.100] / 10
Seeding - Product handling and delivery drive system
47918066 10/09/2015
77.1 [77.100] / 11
Seeding - Product handling and delivery drive system
BAIL14SE00900AC 1
BAIL14SE00900AD 2
6. Remove the bolts and nuts (21) for fixing the box to the
frame on both sides.
Since are two boxes, they also are supported on the
frame in the central portion of the machine.
BAIL14SE00900AE 3
47918066 10/09/2015
77.1 [77.100] / 12
Seeding - Product handling and delivery drive system
7. Remove the triangular ribs (16) that aid in fixing the side
panels (4) and (14) in the rear frame.
BAIL14SE00900AF 4
BAIL14SE00900AG 5
BAIL14SE00586AA 6
47918066 10/09/2015
77.1 [77.100] / 13
Seeding - Product handling and delivery drive system
NOTICE: Refer to Meter box - Adjust (61.904) about the correct assembly and adjustments of the seed metering
system.
47918066 10/09/2015
77.1 [77.100] / 14
Seeding - Product handling and delivery drive system
BAIL14SE00900AH 1
BAIL14SE00900AI 2
5. With the box turned with the cover facing upwards: Re-
move the limiter (3), by removing the fixing bolts and
nuts at both ends.
6. Remove the lid (1), removing the shaft supports (2) on
the side edges of each box.
7. Remove the reinforcement plates (8), removing the
bolts and nuts from the front (10) and rear (11) panels.
BAIL14SE00900AJ 3
47918066 10/09/2015
77.1 [77.100] / 15
Seeding - Product handling and delivery drive system
BAIL14SE00900AN 4
BAIL14SE00900AK 5
10. Remove the lower deflectors (6): for this, remove the
plastic shields (6a) and then the nuts.
BAIL14SE00900AL 6
11. Separate the front panel (10) and rear (11) from the
side supporting panels lafdt (4) and right (14).
12. Separate the remaining parts that compose the box
as needed.
BAIL14SE00900AM 7
47918066 10/09/2015
77.1 [77.100] / 16
Seeding - Product handling and delivery drive system
47918066 10/09/2015
77.1 [77.100] / 17
Seeding - Product handling and delivery drive system
Tank - Emptying
1. Disconnect the seed hoses (27) of the metering units
(13).
BAIL14SE00900AP 1
BAIL14SE00900AO 2
3. Tilt boxes.
47918066 10/09/2015
77.1 [77.100] / 18
Seeding - Product handling and delivery drive system
Tank - Remove
BAIL14SE00900FE 1
NOTE: Follow also by the general identification figure, refer to Tank - Overview Pasture box (77.100)
NOTICE: Typically, you must remove all the pasture boxes thoroughly and perform disassembly on bench.
1. Empty boxes and remove tubes (27) or just unclip them
from the furrow openers.
2. Open and remove the gear drive chain (4) on both sides
and remove the chain.
Remove safeguards (37) and (38) if necessary.
NOTE: The drive of the pasture meters is done on both
sides of the machine, i.e. on the outside of both boxes.
3. Attach a suitable lifting device, that keep the weight
of both boxes suspended in a balanced way, without
subjecting them to excessive bending
4. On both sides of the machine, release the support (7) of
BAIL14SE00900AQ 2
the seed box removing the step bolts, nuts and wash-
ers.
BAIL14SE00900AR 3
47918066 10/09/2015
77.1 [77.100] / 19
Seeding - Product handling and delivery drive system
BAIL14SE00900AT 4
BAIL14SE00900AU 5
BAIL14SE00900AW 6
47918066 10/09/2015
77.1 [77.100] / 20
Seeding - Product handling and delivery drive system
BAIL14SE00900AX 7
BAIL14SE00900AY 8
47918066 10/09/2015
77.1 [77.100] / 21
Seeding - Product handling and delivery drive system
Tank - Install
For the re-installation of boxes, follow the removal pro-
cedure in reverse order.
All rotors (25) should face the right side (seen from be-
hind machine).
47918066 10/09/2015
77.1 [77.100] / 22
Seeding - Product handling and delivery drive system
BAIL14SE00901AA 2
47918066 10/09/2015
77.1 [77.100] / 23
Index
Seeding - 77
47918066 10/09/2015
77.1 [77.100] / 24
Seeding - 77
PS2045 Mechanical
47918066 10/09/2015
77.2 [77.105] / 1
Contents
Seeding - 77
FUNCTIONAL DATA
Seeding tool
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Dynamic description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Gauge wheel
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Press wheel
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SERVICE
Seeding tool
Disassemble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Visual inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Assemble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Gauge wheel
Remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Visual inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Press wheel
Disassemble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Visual inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Assemble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
47918066 10/09/2015
77.2 [77.105] / 2
Seeding - Seeding tool
BAIL14SE00827GC 1
47918066 10/09/2015
77.2 [77.105] / 3
Seeding - Seeding tool
47918066 10/09/2015
77.2 [77.105] / 4
Seeding - Seeding tool
47918066 10/09/2015
77.2 [77.105] / 5
Seeding - Seeding tool
These wheels can limit the planting depth in 15, 25, 40 or 60 mm.
NOTE: these measurements consider new disks
BAIL14SE00740BA 1
47918066 10/09/2015
77.2 [77.105] / 6
Seeding - Seeding tool
BAIL14SE00787GA 1
47918066 10/09/2015
77.2 [77.105] / 7
Seeding - Seeding tool
* These components have differences between the parts of left and right rows.
47918066 10/09/2015
77.2 [77.105] / 8
Seeding - Seeding tool
BAIL14SE00827AV 2
BAIL14SE00656AA 3
10. Remove the inner snap ring (5), that retains the double
bearing (4).
11. Remove bearing (4) of the hub (3), which has re-
cesses to allow the use of a punch
12. Remove the hex nuts and washers (16), separating
the disk from the flange (3)
13. Remove the remaining components.
BAIL14SE00657AA 4
47918066 10/09/2015
77.2 [77.105] / 9
Seeding - Seeding tool
BAIL14SE00902BA 1
47918066 10/09/2015
77.2 [77.105] / 10
Seeding - Seeding tool
shown.
4. Make the connection of the disk to the hub (3).
NOTE: Mounting side of the disks (11) and (15) the coun-
tersunk side (Y) of the passing holes of the bolt (14) should
be left inwards, i.e. between the two disks.
5. On the opposite side, install the lock washers and nuts
(16) tightening them in stages and in a cross, in order
not to deform the disk.
BAIL14SE00659AA 2
BAIL14SE00749CA 3
BAIL14SE00750CA 4
47918066 10/09/2015
77.2 [77.105] / 11
Seeding - Seeding tool
6. With the cavity filled with grease, install the Nilos ring
(2).
BAIL14SE00660AA 5
BAIL14SE00661AA 6
BAIL14SE00662AA 7
12. Bolt (6) on the right side has (X) marks in its hexagonal
head. The thread of this bolt is the "right" type.
13. Bolt (6) on the left side does not have markings and
its thread is the "left" type.
14. The recommended torque for the tightening of M18
bolts (6) is of 176.5 to 215.7 N.m (130.2 to 159 lb.ft).
BAIL14SE00663AA 8
47918066 10/09/2015
77.2 [77.105] / 12
Seeding - Seeding tool
Adjustment:
15. After installing the two hub and disk assemblies on the
support (13) check the clearance between the disks at
the most closed point, with a feeler gauge.
16. The clearance (or opening) at this point should be of
0.012 to 0.031 in (0.3 to 0.8 mm).
17. If necessary, change the number of adjustment shims
(1) in the hub of the smaller disk.
18. After obtaining the clearance adjustment between
disks, do the final assembly.
BAIL14SE00664AA 9
BAIL14SE00665AA 10
20. On the "O" ring, install the hub cap (8) and then the
retaining ring (9).
NOTE: Depending on the "O" ring, the hub cap must be
pressed inwards to allow the installation of the retaining
ring (9).
21. Apply a thin layer of grease under the hub cap (8) just
enough to prevent damage to the "O" ring and help
the seal.
22. Use a tool (W) like the one shown alongside to push
the hub cap (8) and snap ring (9) for its housing.
NOTE: Make sure the snap ring (9) has fit completely into
the groove. BAIL14SE00666AA 11
BAIL14SE00667AA 12
47918066 10/09/2015
77.2 [77.105] / 13
Seeding - Seeding tool
BAIL14SE00668AA 13
47918066 10/09/2015
77.2 [77.105] / 14
Seeding - Seeding tool
BAIL14SE00794HA 14
47918066 10/09/2015
77.2 [77.105] / 15
Seeding - Seeding tool
BAIL14SE00669AA 15
BAIL14SE00828BA 16
BAIL14SE00670AA 17
47918066 10/09/2015
77.2 [77.105] / 16
Seeding - Seeding tool
28. Fit the ducts (12) into support (27) and assemble them
in the row arm (25).
BAIL14SE00902AB 18
BAIL14SE00902AC 19
47918066 10/09/2015
77.2 [77.105] / 17
Seeding - Seeding tool
BAIL14SE00672AA 1
BAIL14SE00673AA 2
47918066 10/09/2015
77.2 [77.105] / 18
Seeding - Seeding tool
BAIL14SE00673AA 1
47918066 10/09/2015
77.2 [77.105] / 19
Seeding - Seeding tool
BAIL14SE00673AA 1
47918066 10/09/2015
77.2 [77.105] / 20
Seeding - Seeding tool
BAIL14SE00902AA 1
BAIL14SE00675AA 2
BAIL14SE00676AA 3
BAIL14SE00677AA 4
47918066 10/09/2015
77.2 [77.105] / 21
Seeding - Seeding tool
BAIL14SE00678AA 5
12. Loosen the bolts (20) and remove the press wheel
assembly (29).
13. Remove the cotter pin (8) nut (9) and pin (11) thereby
separating the support (5) of the press wheel arm.
14. Remove the bushing (7) with the aid of a press and/or
suitable tool.
BAIL14SE00679AA 6
BAIL14SE00751CA 7
BAIL14SE00752CA 8
47918066 10/09/2015
77.2 [77.105] / 22
Seeding - Seeding tool
15. Remove the snap ring (41) the hub cap (40) the "O"
ring (39) the cotter pin (38) and the nut (37).
BAIL14SE00680AA 9
BAIL14SE00681AA 10
BAIL14SE00682AA 11
19. Remove bolts (43) and the weight (42) from the wheel
(34).
BAIL14SE00683AA 12
47918066 10/09/2015
77.2 [77.105] / 23
Seeding - Seeding tool
20. Remove the snap ring (36) Then, remove the bearing
(35) with a press or suitable tool.
BAIL14SE00684AA 13
BAIL14SE00685AA 14
47918066 10/09/2015
77.2 [77.105] / 24
Seeding - Seeding tool
BAIL14SE00686AA 1
47918066 10/09/2015
77.2 [77.105] / 25
Seeding - Seeding tool
BAIL14SE00687AA 1
BAIL14SE00686AA 2
47918066 10/09/2015
77.2 [77.105] / 26
Index
Seeding - 77
47918066 10/09/2015
77.2 [77.105] / 27
CNH Industrial Italia S.p.A. viale delle Nazioni, 55 Modena Italy 41122
All rights reserved. No part of the text or illustrations of this publication may be reproduced.
NEW HOLLAND policy is one of continuous improvement and the right to change prices, specification or equipment
at any time without notices is reserved.
All data given in this publication is subject to production variations. Dimensions and weight are approximate only and
the illustrations do not necessarily show products in standard condition. For exact information about any particular
product, please consult your NEW HOLLAND Dealer.
47918066 10/09/2015
EN
SERVICE MANUAL
Platform, cab, bodywork, and decals
PS2045 Mechanical
47918066 10/09/2015
90
Contents
47918066 10/09/2015
90
Platform, cab, bodywork, and decals - 90
PS2045 Mechanical
47918066 10/09/2015
90.1 [90.118] / 1
Contents
FUNCTIONAL DATA
47918066 10/09/2015
90.1 [90.118] / 2
Platform, cab, bodywork, and decals - Protections and footboards
BAIL14SE00826FB 1
BAIL14SE00826AL 2 BAIL14SE00826AM 3
47918066 10/09/2015
90.1 [90.118] / 3
Platform, cab, bodywork, and decals - Protections and footboards
47918066 10/09/2015
90.1 [90.118] / 4
Index
47918066 10/09/2015
90.1 [90.118] / 5
CNH Industrial Italia S.p.A. viale delle Nazioni, 55 Modena Italy 41122
All rights reserved. No part of the text or illustrations of this publication may be reproduced.
NEW HOLLAND policy is one of continuous improvement and the right to change prices, specification or equipment
at any time without notices is reserved.
All data given in this publication is subject to production variations. Dimensions and weight are approximate only and
the illustrations do not necessarily show products in standard condition. For exact information about any particular
product, please consult your NEW HOLLAND Dealer.
47918066 10/09/2015
EN
47918066 10/09/2015
EN
CNH Industrial Italia S.p.A. viale delle Nazioni, 55 Modena Italy 41122
All rights reserved. No part of the text or illustrations of this publication may be reproduced.
NEW HOLLAND policy is one of continuous improvement and the right to change prices, specification or equipment
at any time without notices is reserved.
All data given in this publication is subject to production variations. Dimensions and weight are approximate only and
the illustrations do not necessarily show products in standard condition. For exact information about any particular
product, please consult your NEW HOLLAND Dealer.
47918066 10/09/2015
EN