Professional Documents
Culture Documents
8998 01 Atlas Copco Air Motors
8998 01 Atlas Copco Air Motors
ATEX 108
• Explosion prevention guidelines
• ATEX code definition
For each Atlas Copco motor/gear unit combination the The output of an air motor is most clearly seen from its
following information is presented in this catalogue. performance curves, Figure 8. For each motor/gear unit the
power, torque and air consumption are shown as a function
1. Tabular data – summary of main performance of speed.
parameters.
The diagrams shown apply to an inlet pressure of 6.3 bar,
2. Dimensional drawings. to calculate performance at other pressures refer to page 7 in
this catalogue.
3. Performance curves.
Torque
Nm
Notes on performance data Power
kW Air cons.
Power l/s
The performance data stated in this catalogue is valid for an Max
output
air supply pressure of 6.3 bar (91 psi), gauge.
Air consumption values are for free air delivery – Air. cons.
(i.e., the volume the consumed air would occupy if allowed to
expand to atmospheric pressure).
Speed r/min
Figure 8
NOTE: The starting torque produced by an air motor is variable and depends
on vane position. These diagrams do not indicate the starting torque – this
can be obtained from data tables, where the minimum value is shown.
LZB33 - L - AR150 - 11
Torque
Nm
Desired working point
Example: Torque with standard
motor at 6.3 bar (91 psi )
A Non-reversible motor is required to run at 300 r/min and produce Torque with throttled
a torque of 10 Nm. Selection of correct motor size is as follows: motor
Power required (W) = 3.14 x 10 x 300/30 = 314 Torque with pressure
From Table 5 the correct size of Non-reversible motor for this regulator
application is the LZB 33.
Once the motor size has been identified, simply look at the
performance curves for each motor variant and select the one
with max. output nearest to the working point. For the above
example this would be the LZB33-L-A007-11. Speed r/min Figure 7
Many applications demand that a motor produces a minimum Certain applications require the acceleration of a load up to
torque at start-up. In these a minimum starting torque, for a given speed. In these cases, the choice of motor involves
a given motor, can be looked up in the tabular data. If it is complex calculations. It is therefore recommended that you
necessary to modify the motor’s output, but also maintain a seek guidance from your nearest Atlas Copco representative
high starting torque, the technique of throttling the air flow before proceeding.
should be utilized.
The noise generated by an air motor is mainly caused by the Atlas Copco air motors are found in use in many hostile
exhaust air of the motor. The noise level increases with speed environments, often with little or no modification. These
and is greatest at the free speed. environments are typified as being: Acidic – Explosive –
Radioactive – High temperature – Moist – Dusty – Intense
All Atlas Copco motors are supplied with a threaded exhaust electric fields – Underwater – High humidity. It is also possible
port which, to reduce noise levels, can accept a screw in to power an air motor with many types of compressed gas,
silencer. However, an exhaust hose can also be fitted, and for example nitrogen or natural gas. However, to ensure safe
when used with a silencer, it can reduce noise levels even and reliable service, we recommend you always consult your
further. The effects of employing the various silencing local Atlas Copco representative before using an air motor in
techniques are indicated in tables in chapter Accessories. a hostile environment.
Find our test information in the air motor selection tool:
https://webbox.atlascopco.com/airmotor
Temperature
The performance of an air motor is dependent on the point is often referred to as ”torque at maximum output.”
inlet pressure. At a constant inlet pressure, ungoverned air
motors exhibit the characteristic linear output torque/speed The performance curves for an ungoverned air motor
relationship. Figure 1. operating at a constant air pressure are illustrated in Figure 3.
Torque
Torque Nm
[Nm] Torque
Stall
torque Power
Min
starting
torque
However, by simply regulating the air supply, using the The use of gear units
techniques of throttling or pressure regulation, the output of
an air motor can easily be modified. Air motors operate at high speed and, although they can be
controlled over a wide speed range, the output characteristics
The free speed and torque can be regulated down to 50% for are not always suitable for the application. To achieve the
an LZB air motor. The free speed for an LZL can be regulated required output an appropriate gear unit can be selected.
down to 10% and the torque can be regulated down to 20%. The ability to change the output by use of a gear unit is
The shaded areas in Figure 2 illustrate this. illustrated in Figure 4.
Torque
Nm
Torque Torque Torque
100% 100%
100 100 Power
50 50
2:1
20 1:1
4:1
50 100 10 50 100
Speed 100% Speed 100%
LZB LZL/PZB 1:1, 2:1, 4:1 = gear ratios Speed r/min
Figure 4
Figure 2
It should be noted that all vane air motors produce a variable The planetary and helical gear units used by Atlas Copco have
starting torque, due to the position of the vanes in the motor a high level of efficiency that can be assumed to be 100%.
when it is started. The variation differs between motor types The power output remains virtually unchanged also when
and must be checked on an individual basis. gears are used.
The recommended dimensions of air lines are given in the Atlas Copco’s LZB vane motors and LZB stainless steel run
introductory section to each motor type. Note that exhaust with lubrication free vanes as standard.
hose is larger than inlet hose.
The LZB motors with lubricated free vanes can still be
The recommendations are valid for hose lengths of up to 3 lubricated, if the application requires it, but is not dependent
meters. For distances between 3 and 15 meters select a hose on lubricated air, as with traditional vanes.
diameter one size up, and for distances between 15 and 50
meters select a hose diameter two sizes up. If running a motor with 100% dry air and no lubrication,
performance can be reduced depending on model.
It is important to note that the output of the motor will be
reduced if these guidelines are not followed. The table below shows how reduced lubrication can affect
service life and power for a lubricated vane motor.
Lubricant
Recommended hose connectors quantity
Lubricant free vanes Conventional lubricated vanes
0 500 – 1000 85 – 95 10 – 30 30
Air preparation
A = Filter
B = Pressure regulator
Figure 9
C = Oil fog lubricatior
These valves are used to start or stop a motor, or to change 3/2 valve
its direction of rotation. It is most usual to use what is termed
a 5/3 valve to control a reversible motor, and a 3/2 valve to
control a Non-reversible motor.
Installation examples
NOTE: For LZL air motors it is important that an inlet restrictor is p
laced
Typical installation diagrams for type LZB and LZL air motors, upstream from the inlet. It must be placed so it does not affect the exhaust
together with their associated control valves, filters, regulators at reversible running. This means that it has to be placed before the
lubricators and silencers. control valve.
LZL Circuits
LZB Circuits
Non-reversible duty
Reversible duty
with 5/3 valve and
closed mid position
Figure 11
Reversible duty
with 5/3 valve and
open mid position
Figure 12
A = Filter
B = Pressure regulator
C = Oil fog lubricator
D = Silencer
E = 5/3 valve
F = Air motor
Figure 13
The direction of rotation is controlled manually by a lever-operated 5/3 valve. The air
preparation unit ensures that the motor is supplied with clean air and lubrication. The
built-in pressure regulator can also be used to modify the output of the motor.
A throttle is usually fitted into the motor´s inlet, although When using a pressure regulator it is mostly fitted into the
it can also be complemented with some throttling at the motor´s inlet hose. The use of pressure regulation is ideal
exhaust. You should never create a back pressure above 1 bar when control of the stall torque is required and a high
at the exhaust. starting torque is not so important, Figure 6.
Torque Torque
Nm %
100
Figure 5 Figure 6
Speed r/min 100
Speed %
Pressure regulation
Example:
Sometimes the motor operates at other supply pressures than An LZB22-L-A036-11 is required to run at 1155 r/min and produce
6.3 bar. In these cases the performance of a motor must be 1.2 Nm; calculate the required inlet pressure to achieve this.
re-calculated to ensure the working point can be achieved. For this motor at maximum output the torque is 1.5 Nm and the
speed is 1650 r/min.
To calculate performance at supply pressures other than 6.3 M1 = desired torque
n1 = desired speed
bar, multiply the data at 6.3 bar by the correction factors M2 = torque at maximum output
shown in table below. n2 = speed at maximum output
Correction factors
Apply these values to the diagram in Figure 8 and read off the pressure at
Air pressure
Air the intersection point.
Output Speed Torque
consumption The required inlet pressure is 4.2 bar (61 psi)
bar psi
M1
7 101 1.13 1.01 1.09 1.11
M2
6 87 0.94 0.99 0.95 0.96 2.2
5 73 0.71 0.93 0.79 0.77 2.0
1.8
4 58 0.51 0.85 0.63 0.61
1.6
3 44 0.33 0.73 0.48 0.44 bar
1.4
7 psi
1.2
It is also easy to calculate the inlet pressure required to 6 101
1.0
achieve a desired working point. 5 87
0.8
4 73
0.6
3 58
0.4
44
0.2 n1
n2
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 Speed Figure 8
r/min
LZB Vane motors – 0.1 kW to 2.8 kW The motors have double seals in Viton at the output shaft
to prevent dirt and liquids from entering the motor gears.
Type LZB Atlas Copco vane motors are compact in design, The seals also prevent the gear lubricant from leaking out.
light in weight, and available with a host of different gear All external parts, including the output shaft, are made of
ratios to meet a variety of speed and torque requirements. stainless steel. The grease in the motor complies with NSF
They are particularly suitable for building into handheld H1 and FDA 21CFR § 178.3570. For applications where there
machines, or indeed any industrial equipment. might be moisture in the compressed air the stainless steel
LZB-motors can be equipped with a stainless steel motor
cell as an option. With this option the motor becomes 100%
Planetary gear units stainless, both internal and external.
All our air motors are ATEX Certified for fixtured applications,
in compliance with the European Union’s ATEX directive
2014/34/EU. For equipment used in potentially explosive
environments. The LZL motors with Helical gears are not
ATEX Certified.
Fr
LZB vane motors are designed to provide high performance N
and high standards of reliability. They are characterized by 3500
high power output and small physical size, Figure 12.
3000
2500
2000
1500
1000
500
Fa
N
500 1000 1500 2000 2500 3000 3500 4000 4500 5000
Figure 12
Curve e
Curve g
The design of the motor is long and slim. This gives a number
A
of advantages, such as high power-to-volume ratio, low air Fr
consumption and long vane life. All motors utilize five vanes, Cylindric Threa
which are supplied with vane air, to ensure excellent starting
Fa
and low speed performance. Multi-step planetary gears are
used to meet the torque and speed requirements of the shaft shaft
application, offering high efficiency with compact dimensions.
Figure 14
Shaft loading Fr
N
Curve d A = 20 mm
500 Curve c A = 15 mm
A Fr Curve b A = 9 mm
Curve a A = 8 mm
Fr Fr
N
N
4000
450
400
350 3000
300
250
2000
200
150
1000
100
50
0 Fa Fa
500 1000 1500 2000 2500 N N
1000 2000 3000 4000 5000 6000 7000
Curve a Curve h A = 20 mm
Curve b Curve g A = 15 mm
Curve c Curve f A = 20 mm
Curve e A = 15 mm
Type LZB vane motors may be mounted in any position. Non-reversible motor
To facilitate this, flange and foot mounting are available for When the compressed air supply is connected to the inlet,
eachmotor, Figure 15. the direction of rotation will be as shown in Figure 16. If the
exhaust air is to be piped away, a hose should be connected
to the exhaust outlet. (EXH).
Reversible motor
The compressed air supply should be connected to the inlet
that gives the desired direction of rotation, Figure 17. The
inlet not in use functions as an additional outlet: it must not
be plugged.
Foot
Clockwise Figure 16
rotation
Anti-clockwise
rotation
Flange
Figure 17
Anti-clockwise
rotation
Clockwise
rotation
Figure 15
Hose dimensions
Information on hose dimensions recommended for use with type LZB air motors is detailed in table below. These dimensions
are valid for hose lengths up to 3m. If lengths above that are used, choose a one size larger hose.
Motor size Rotation BSP NPTF mm Ordering No. mm BSP mm Ordering No. mm
LZB14 A, AV, AR 1/8 - 8 9000 0240 00 5.0 1/8 8 9000 0240 00 5.0
LZB22 AR, LR 1/8 - 8 9000 0240 00 5.0 1/8 8 9000 0240 00 5.0
LZB33, LZB34 A, AV, AR, LR 1/4 - 10 9000 0247 00 8.0 1/4 10 9000 0247 00 8.0
LZB46 A, AV, AR 1/4 - 10 9000 0247 00 8.0 1/2 16 9000 0244 00 13.4
LZB54 A, AV, AR 3/8 - 13 9000 0248 00 9.3 1/2 16 9000 0244 00 13.4
* Recommended minimum inner diameter (for reversible motors, the same size should be used on both in-/outlet)
** Alternative connection thread BSP 1/2" delivered with the product
Atlas Copco Air Motors | 17
Vane motors LZB14-L
Lubrication free
0.11 – 0.16 kW
0.15 – 0.21 hp
1)
For Shaft loading curves, see page 14.
NOTE: - If running motors with 100% dry air and no lubrication, performance can be reduced with 5-15% at max output.
- To optimize life time for a lubrication free motor, use lubricated air if the application allows it.
Dimensions (mm) Conversion factor 1 mm = 0.04 inch
17 111*
123*
12 Ø27
9.5
7.9
111*
2
BSP 1/8”
5/16” -24 UNF
A/F 23
Reversible 6.8
6.8
3.95
6.8
*) +9.8 mm for LZB14
Ø6 h7
AV012, AV007
2 h7
BSP 1/8”
A/F 25
Optional mountings
52
2
3.5
R1
30
ø30h7
80
29.5
30
M5 21 5 ø5.5
60
28.2 15.5
Foot Flange
Ordering No. 4430 0189 80 Ordering No. 4430 0165 85
0.11 – 0.16 kW
0.15 – 0.21 hp
Material in parts:
1)
For Shaft loading curves, see page 14.
NOTE: - If running motors with 100% dry air and no lubrication, performance can be reduced with 5-15% at max output.
- To optimize life time for a lubrication free motor, use lubricated air if the application allows it.
17.1 114.2*
12 Ø27
7.9
2
BSP 1/8”
A/F 23
Reversible
6.8
6.8
3.95
6.8
*) +9.8 mm for LZB14-RL
A012, A007, AR008, AR005
Ø6 h7
7.9
2 h7
BSP 1/8”
A/F 25 Optional mountings
52
2
3.5
R1
30
ø30h7
72
29.5
30
M5 21.8 5 ø5.5
60
28.2 15.5
Foot Flange
Ordering No. 4430 0923 80 Ordering No. 4430 0922 80
0.08
kW Nm0.4 LZB14-L-AR008 4l/s 0.08
kW 1.2
Nm LZB14-L-AR005 4l/s 0.08 1.6 4
0.06 0.36
0.12 3 0.12
0.06 9.0
0.9 3 0.06 1.2 3
0.10 0.25 0.10 0.6
7.5
0.04 25 0.04 25 0.04 0.8 2
0.08 0.14 0.08 0.3
6.0
0.02 14 0.02 14 0.02 0.4 1
0.06 3 3 0.06 4.5 3
4000 8000 12000 r/min 500 100015002000250030003500 r/min 400 800 1200 1600 2000 2400 r/min
0.04 2 2 0.04 3.0 2
0.02 1 1 0.02 1.5 1
kW Nm LZB14-L-AR008 l/s kW Nm LZB14-L-AR005 l/s
0.12 6 0.12 9.0
200 400 600 800 1000 r/min 100 200 300 400 500 r/min
0.10 5 5 0.10 7.5 5
200 400 600 800 1000 r/min 100 200 300 400 500 r/min
Torque
Nm
Power
kW Air cons.
Power l/s
Max
output
Air. cons.
Conversion factors
1 kW = 1.34 hp
Torque
1 Nm = 0.74 Ibf - ft
Torque
at max
power 1 l/s = 2.1 cfm
1 hp = 0.75 kW
1 Ibf-ft = 1.36 Nm
Speed r/min
1 cfm = 0.47 l/s
0.16 – 0.27 kW
0.21 – 0.36 hp
1)
For Shaft loading curves, see page 14.
NOTE: - If running motors with 100% dry air and no lubrication, performance can be reduced with 5-15% at max output.
- To optimize life time for a lubrication free motor, use lubricated air if the application allows it.
Clockwise
9.5
BSP 1/8”
A/F 31
6
7.5
23.5 110.9*
Anti-clockwise 16 Ø36
BSP 1/8”
3
M4
A/F 33
11.4
Ø12
7.7
BSP 1/4”
THREAD DEPTH 12 mm 3 h7
A/F 31
Reversible
Ø10 h6
*) +31 mm for
11.2
9.5
LZB22-L - A011 LZB22-L - AV011 LZB22-L - AR006
9.5 LZB22-L - A008 LZB22-L - AV008 LZB22-L - AR005
LZB22-L - A005 LZB22-L - AV005 LZB22-L - AR003
A/F 31
6
127*
3/8” -24 UN
16
F
111*
BSP 1/8”
11
Ø18
Optional mountings 26
2
60
8
R1
30
Ø30h7
80
30
32
10
M5 15 5 Ø5.5
50 37.2 18
Foot Flange
Ordering No. 4430 0160 80 Ordering No.
4110 0984 85 with holes
4110 0984 80 without holes
0.16 – 0.27 kW
0.21 – 0.36 hp
Material in parts:
1)
For Shaft loading curves, see page 14.
NOTE: - If running motors with 100% dry air and no lubrication, performance can be reduced with 5-15% at max output.
- To optimize life time for a lubrication free motor, use lubricated air if the application allows it.
3 18
6
3 h7
Ø12
7.5
11.2
Ø36
5 BSP 1/4”
Ø10 h6
THREAD DEPTH 8 mm
Reversible 9.5 *) +31.2 mm for
9.5 LZB22-RL - A011 LZB22-RL - AR006
LZB22-RL - A008 LZB22-RL - AR005
LZB22-RL - A005 LZB22-RL - AR003
A/F 31
26.5
6
Optional mounting 2
8
60
BSP 1/8”
8
R1
30
Ø30 h7
72
30
32
10
M5 15 5 Ø5.5
50 37.2 18
Foot Flange
Ordering No. 4430 0862 80 Ordering No. 4430 0861 80
0.20
kW 0.60 LZB22-L-A220 6.0 0.20 2.0 6.0 0.20 4 LZB22-L-A036 6.0
Nm l/s kW Nm LZB22-L-A049 l l/s kW Nm l/s
0.30 0.45
0.15 4.5 0.30 1.5
0.15 3.0 4.5 0.30
0.15 3 4.5
0.25 0.30
0.10 0.75 7.5
3.0 0.25 1.0
0.10 2.5 7.5
3.0 0.25
0.10 2 7.5
3.0
0.20 0.15
0.05 0.60 6.0
1.5 0.20 0.5
0.05 2.0 6.0
1.5 0.20
0.05 14 6.0
1.5
0.15 0.45 4.5 0.15 1.5 4.5 0.15 3 4.5
4000 8000 12000 16000 20000 24000 r/min 1000 2000 3000 4000 5000 r/min 1000 2000 3000 4000 r/min
0.10 0.30 3.0 0.10 1.0 3.0 0.10 2 3.0
0.05 Nm
kW 0.15 LZB22-L-A022 l/s
1.5 kW Nm
0.05 0.5 LZB22-L-A011 l/s
1.5 0.05 Nm1
kW LZB22-L-A008 l/s
1.5
0.30 0.30 12 0.30 18
4000 8000 12000 16000 20000 24000 r/min 1000 2000 3000 4000 5000 1000 2000 3000 4000 r/min
0.25 7.5 7.5 0.25 10 7.5r/min 0.25 15 7.5
0.25 3.0
0.10 7.5 7.5
3.0 0.25
0.10 10
4 7.5
3.0 0.25
0.10 15
6 7.5
3.0
0.20 1.5
0.05 6.0 6.0
1.5 0.20
0.05 28 6.0
1.5 0.20
0.05 12
3 6.0
1.5
0.05
kW Nm1.5 LZB22-L-A005 1.5
l/s 0.05 2 1.5 0.05 3 1.5
0.30 30
400 800 1200 1600 2000 2400 r/min 200 400 600 800 1000 1200 r/min 200 400 600 800 1000 r/min
0.25 25 7.5
0.20 20 6.0
kW Nm LZB22-L-A005 l/s
0.30 15
0.15 30 4.5
0.25 10
0.10 25 7.5
3.0
0.20
0.05 20
5 6.0
1.5
0.15 15 4.5
100 200 300 400 500 r/min
0.10 10 3.0
0.05 5 1.5
1)
For Shaft loading curves, see page 14.
NOTE: - If running motors with 100% dry air and no lubrication, performance can be reduced with 10-20% at free speed.
- To optimize life time for a lubrication free motor, use lubricated air if the application allows it.
0.16 45
50
0.14 40
0.015
35
40 0.12
30
0.10
30 25 0.010
0.08
20
20 Limit 0.06 Limit
15
0.04 0.005
10
10
0.02
5
0 0 0 0
0 20 40 60 80 100 120 140 r/min 5.6 5.7 r/min
Reversible 198.5*
9.5 16
Ø36
3
198.5* 3 h7
M4
9.5 23.5 172.9*
A/F 31
Ø10 h6
A/F 33
11.2
Ø12
6
9.5 16
8
Ø36
3
3 h7
M4
Ø10 h6
A/F 33
11.2
Ø12
6
8
Optional mountings 26
2
BSP 1/8” THREAD DEPTH 12mm
60
8 26
R1
30
2
Ø30h7
80
60
30
32
8
R1
30
10
Ø30h7
80
M5 15 5 Ø5.5
50 37.2
30
18
32
10
Foot Flange
Ordering No. 4430 0160 80 Ordering No. 4110 0984 85 with holes
M5 15 5 Ø5.5
4110 0984 80 without holes
50 37.2
18
202.1*
9.5 18
Reversible Ø36
3
202.1* 3 h7
M4
A/F 33
11.2
Ø12
6
9.5 18
8
Ø36
3
3 h7
M4
A/F 33
11.2
Ø12
6
8
26.5
2
Ø30 h7
72
60
30
32
8
R1
10
30
Ø30 h7
M5 15 Ø5.5
72
50 37.2 18
30
32
10
M5 15 5 Ø5.5
50 37.2 18
Foot Flange
Ordering No. 4430 0862 80 Ordering No. 4430 0861 80
0.24 – 0.39 kW
0.32 – 0.52 hp
NOTE: - If running motors with 100% dry air and no lubrication, performance can be reduced with 5-15% at max output.
- To optimize life time for a lubrication free motor, use lubricated air if the application allows it.
LZB33-L, for mounting with IEC flange (flange has to be ordered separetly)
Data at air pressure 6.3 bar (91 psi)
Speed Torque Min Air
Max at max at max starting Stall Free consumption
output output output torque torque speed at max Weight
Model output Shaft loading
Lubrication free kW hp r/min Nm lb-ft Nm lb-ft Nm lb-ft r/min l/s cfm kg lb code ATEX code Ordering No.
Clockwise rotation (Keyed shaft)
LZB33-L-A013-20 0.38 0.51 580 6.4 4.7 12 8.9 12.8 9.4 1180 8.1 17.2 1.02 2.25 d Ex II 2GD h T6 IIC T85°C 8411 0352 75
LZB33-L-A007-20 0.38 0.51 320 11.5 8.5 21 15.5 23 17 650 8.1 17.2 1.02 2.25 d Ex II 2GD h T6 IIC T85°C 8411 0352 83
LZB33-L-A005-20 0.38 0.51 260 14.2 10.5 26 19.2 28 21 520 8.1 17.2 1.02 2.25 d Ex II 2GD h T6 IIC T85°C 8411 0352 91
LZB33-L-A0030-11 0.37 0.5 160 22.3 16.4 40 30 45 33 340 8.1 17.2 1.5 3.31 d Ex II 2GD h T6 IIC T85°C 8411 0306 72
Anti-Clockwise rotation (Keyed shaft)
LZB33-L-AV0030-11 0.37 0.5 160 22 16.2 38 28 44 32 340 9.5 20.2 1.5 3.31 d Ex II 2GD h T6 IIC T85°C 8411 0345 59
Reversible (Keyed shaft)
LZB33-L-AR0026-11 0.24 0.32 120 19 14 25 18.4 38 28 230 7.9 16.8 1.5 3.31 d Ex II 2GD h T6 IIC T85°C 8411 0308 70
NOTE: - If running motors with 100% dry air and no lubrication, performance can be reduced with 5-15% at max output.
- To optimize life time for a lubrication free motor, use lubricated air if the application allows it.
151*
31.5 119.5*
A/F 34
9
20 Ø41.5
9
5.5
7.5
151* 4 h7
BSP 1/4”
M4
31.5 119.5*
A/F 34
Ø12 h6
Anti-clockwise
A/F 38
13.5
20 Ø41.5
9
9
5.5
7.5
4 h7
BSP 1/4”
M4
Ø12 h6
A/F 38
13.5
LZB33-L-A013 LZB33-L-AV013 LZB33-L-AR009
9
9
LZB33-L-A007 LZB33-L-AV007 LZB33-L-AR005
Threaded shaft (-12) LZB33-L-A005 LZB33-L-AV005 LZB33-L-AR004
7.5
BSP 1/4”
135.5*
3/8” -24 UNF
16
9
Reversible 9
119.5*
9 11
BSP 1/4”
135.5*
3/8” -24 UNF
16 119.5*
A/F 34
Ø 41.5
7.5
9
Ø18
9 11
9
BSP 1/4”
A/F 34
Ø 41.5
7.5
Ø18
9
32.5
Optional mounting 2
BSP 1/4”
60
0.7
R2 32.5
35
Ø36 h7
2
90
60
35
34.7
10
0.7 5.5
R2
35
Ø36 h7
M5 20 5
21
90
50 42.7
35
34.7
Foot Flange
10
230
34.5 195
30 17 7
LZB33-L-A0030 25
LZB33-L-AV0030 230 *
LZB33-L-AR00262
34.5 195 * 5 h7
*) - 32 mm
LZB33-L-A013-20 30 17 7
Ø14 h6
Ø41.5
16.1
Ø42
M4
54
LZB33-L-A007-20
70
25
LZB33-L-A005-20
2
5 h7
Ø6.5
Thread length 12
Ø14 h6
Ø41.5
16.1
Ø42
M4
54
70
Ø6.5
Thread length 12
IECff85
32.8 19
Ø 7 (4x)
-0.2
Ø 70 js7
0
Ø 105
Ø 70 90º (x4)
0
2.5-0.5
9 Ø 85
IECff130
32.8 19
Ø10 (4x)
-0.2
Ø110js7
0
Ø160
2.5 0
-0.5
9 Ø130
0.25 – 0.39 kW
0.34 – 0.52 hp
Material in parts:
1)
For Shaft loading curves, see page 14.
NOTE: - If running motors with 100% dry air and no lubrication, performance can be reduced with 5-15% at max output.
- To optimize life time for a lubrication free motor, use lubricated air if the application allows it.
155.2*
9
31.5 123.7*
BSP 1/4”
30
Reversible
9 25
Ø41.5
9
3
4 h7
M4
A/F 34
A/F 38
Ø12 h6
7.5
13.5
Ø15
9
*) +34.5 mm for
LZB34-RL-A013 LZB34-RL-AR009
LZB34-RL-A007 LZB34-RL-AR005
LZB34-RL-A005 LZB34-RL-AR004
Optional mounting
Foot Flange
Ordering No. 4430 0855 80 Ordering No. 4430 0850 80
4000 8000 12000 16000 20000 24000 r/min 1000 2000 3000 4000 5000 6000 r/min 500 1000 1500 2000 2500 3000 3500 r/min
500 1000 1500 2000 2500 3000 r/min 200 400 600 800 1000 1200 1400 r/min 100 200 300 400 500 600 700 800 r/min
100 200 300 400 500 600 r/min 50 100 150 200 250 300 350 400 r/min 40 80 120 160 200 240 r/min
40 80 120 160 200 r/min 20 40 60 80 100 120 140 r/min 20 40 60 80 100 r/min
5 10 15 20 25 30 35 r/min 4 8 12 16 20 24 r/min
4000 8000 12000 r/min 1000 2000 3000 4000 r/min 400 800 1200 1600 2000 2400 r/min
400 800 1200 1600 2000 r/min 200 400 600 800 1000 r/min 100 200 300 400 500 r/min
0.30 24 0.30
0.25 20 10 0.25 10
0.20 16 8 0.20 40 8
0.15 12 6 0.15 30 6
0.10 8 4 0.10 20 4
0.05 4 2 0.05 10 2
50 100 150 200 250 300 350 400 r/min 40 80 120 160 200 240 r/min
Torque
Nm
Power
kW Air cons.
Power l/s
Max
output
Air. cons.
Conversion factors
1 kW = 1.34 hp
Torque
1 Nm = 0.74 Ibf - ft
Torque
at max
power 1 l/s = 2.1 cfm
1 hp = 0.75 kW
1 Ibf-ft = 1.36 Nm
Speed r/min
1 cfm = 0.47 l/s
Air
Free speed consumption Weight
Model at free speed Shaft
Lubrication free r/min l/s cfm kg lb loading code 1) ATEX code Ordering No.
Reversible (Keyed shaft)
LZB33-L-LR200-11 180 9.9 21.0 1.25 2.78 c Ex II 2GD h T6 IIC T85°C 8411 0308 62
LZB33-L-LR44-11 42 9.9 21.0 1.55 3.44 c Ex II 2GD h T6 IIC T85°C 8411 0308 54
LZB33-L-LR20-11 18 9.9 21.0 1.55 3.44 c Ex II 2GD h T6 IIC T85°C 8411 0308 47
LZB33-L-LR10-11 10 9.9 21.0 1.8 4.0 c Ex II 2GD h T6 IIC T85°C 8411 0308 39
Stainless steel Reversible (Keyed shaft)
LZB34-RL-LR200-11 180 9.9 21.0 1.45 3.2 c Ex II 2GD h T6 IIC T85°C 8411 0343 44
LZB34-RL-LR44-11 42 9.9 21.0 1.75 3.86 c Ex II 2GD h T6 IIC T85°C 8411 0343 51
LZB34-RL-LR20-11 18 9.9 21.0 1.75 3.86 c Ex II 2GD h T6 IIC T85°C 8411 0343 69
LZB34-RL-LR10-11 10 9.9 21.0 2.0 4.4 c Ex II 2GD h T6 IIC T85°C 8411 0343 77
1)
For Shaft loading curves, see page 14.
NOTE: - If running motors with 100% dry air and no lubrication, performance can be reduced with 10-20% at free speed.
- To optimize life time for a lubrication free motor, use lubricated air if the application allows it.
45 0.14
0.25 50
40
0.12
35 40
0.20
0.10
30
25 0.15 30 0.08
Limit
20 Limit
0.06
0.10 20
15
0.04
10 0.05 10
0.02
5
0 0 0 0
0 20 40 60 80 100 120 140 160 180 200 r/min 35 36 37 38 39 40 41 r/min
Nm LZB33-L-LR20 kW Nm LZB33-L-LR10 kW
80 0.12 80 0.06
70 70
0.10 0.05
60 60
0.08 0.04
50 50
40 40 0.03
0.06
30 30
Limit Limit 0.02
0.04
20 20
0.01
0.02 10
10
0 0
0 0 8.8 9.0 r/min
17 18 r/min
218*
9 20
9 Ø41.5
5.5 4 h7
7.5
M4
A/F 38
Ø12 h6
A/F 34
218*
13.5
9
31.5 186.5*
9 20
9 Ø41.5
BSP 1/4” THREAD DEPTH 12mm
5.5 *) +33.5 mm for LZB33-L-LR44, -LR20 4 h7
7.5
A/F 38
Ø12 h6
A/F 34
13.5
9
Optional mounting
BSP 1/4” THREAD DEPTH 12mm
2
60
0.7
R2
35
Ø36 h7
90
2
34.7
35
Flange
10
60
5.5
Ordering No.
M5 20 0.7
R2 4110 0878 85 with holes
35
50 42.7 32.5 5 4110 0878 80 without holes
Ø36 h7
21
90
Foot
34.7
35
Ordering No. 4430 0162 80
10
M5 20 5.5
50 42.7 32.5 5
224.2* 21
Dimensions (mm) Conversion factor 1 mm = 0.04 inch
31.5 192.7*
9
9 3 25
Ø41.5
4 h7
7.5
M4
A/F 34
A/F 38
Reversible 224.2*
13.5
9
31.5 192.7*
9
Ø12 h6
9 3 25
Ø41.5
BSP 1/4” THREAD DEPTH 8mm
4 h7
7.5
M4
A/F 34
A/F 38
13.5
9
Ø12 h6
0. 7
35
R2
Ø36 h8
Optional mounting
82
2
34.7
35
10
60
M5 20 0. 7 Ø5.5
35
R2
50 42.7 33.5 5 21
Ø36 h8
82
34.7
35
10
M5 20 Ø5.5
50 42.7 33.5 5 21
Foot Flange
Ordering No. 4430 0855 80 Ordering No. 4430 0850 80
0.23 – 0.37 kW
0.31 – 0.50 hp
1)
For Shaft loading curves, see page 14.
NOTE: - If running motors with 100% dry air and no lubrication, performance can be reduced with 5-15% at max output.
- To optimize life time for a lubrication free motor, use lubricated air if the application allows it.
43.7 250.2
7.5
40 43.7 95.7
7.5
A/F 34
Ø60
30 40 95.7
9
9
A/F 34
5 Ø60
9 30 6 h7
9
5
250.2 6 h7
Ø41.5
A/F 55
BSP 1/4”
Ø19 j6
250.2
21.5
Ø30
M5
43.7
7.5 7.5
43.7
Ø41.5
A/F 55
Reversible BSP 1/4” 40 95.7
Ø19 j6
21.5
Ø30
M5
34 34
40 95.7 Ø60
9
A/FA/F
30 Ø60
9 9
9 5 30
9 5 THREAD DEPTH 15mm 6 h7
9 6 h7
THREAD DEPTH 15mm
7.5
Ø41.5
55 55
BSP 1/4”
j6 j6
21.521.5
Ø30Ø30
M5M5
Ø19Ø19
A/FA/F
Ø41.5
BSP 1/4”
A/F 34
A/F 55
7.5
9
9
A/F 34
A/F 55
9 9
9
BSP 1/4”
34 34
55 55
A/FA/F
A/FA/F
9 9
Optional mounting
BSP 1/4”
14
BSP 1/4”
80
14
50
80 R3
0
Ø60 h8
118
50
44
14
50
0
R3
Ø60 h8
14
10
118
M6 80 30
60 80 61.2
44
Ø10.3
50
42 3
35
10
50 50
0
M6 R3 30
h8h8
0
R3 61.2
118118
Ø60
60 Ø10.3
Ø60
42 3
35
44 44
50 50
10 10
Foot M6 30 Flange
M6 30
Ordering No. 4430
60 0178 80 61.2
61.2
Ordering No. 4430 0569 84 Ø10.3
60 42 3 Ø10.3
42 3 35
35
320.2
62 258.2
Clockwise Reversible
M8 6 holes 18 mm DEEP
60 48 75 95.7
5 50 25 LZB33-L-A0005 LZB33-L-AR0004
Ø60
LZB33-L-A0004 320.2
LZB33-L-AR0003 6P
9
LZB33-L-A0003 LZB33-L-AR0002
R36.5
62 258.2
LZB33-L-A0002 LZB33-L-AR0001
Ø83 h9
Ø62 K6
M8 6 holes 18 mm DEEP
Ø41.5
M10
60 48 75 95.7
50 25
245
Ø60
9
320.2 6P
320.2
R36.5
62 258.2
2.7 62
Ø83 h9
258.2
Ø62 K6
M8 6 holes 18 mm DEEP
Ø41.5
60 48 75 95.7
M10
M8 6 holes 18 mm DEEP
60 48 75 95.7
50 25 Ø28j6
5
5024 25
Ø60
5 8h7
Ø60
9
6 P9
6P
R36.5
R36.5
31
h9h9
K6K6
2.7
Ø41.5
M10
Ø83
Ø62
Ø41.5
M10
Ø83
Ø62
24 Ø28j6
24 8h7
2.7
31
2.7
Ø28j6
Ø28j6
8h7
8h7
3131
40 80 120 160 200 240 r/min 40 80 120 160 200 r/min 20 40 60 80 100 120 140 r/min
Reversible (AR)
5 10 15 20 25 30 4 8 12 16 20 r/min 3 6 9 12 15 r/min
0.23 – 0.25 kW
0.31 – 0.34 hp
2)
Flange is mounted and supplied with the motor.
The brake needs minimum 3 bar to release. Performance curves same as standard motors, see page 35 and 40.
NOTE: - If running motors with 100% dry air and no lubrication, performance can be reduced with 5-15% at max output.
- To optimize life time for a lubrication free motor, use lubricated air if the application allows it.
4h7 4h7
4h7
55
7.5
55
7.5
7.5
Ø41.5
Ø41.5
Ø41.5
Ø41.5
55
13.5
13.5
M4 M4
M4
7.5
Ø41.5
Ø41.5
9
9
13.5
9
Ø12h6
9
60
Optional mounting
7.5
Ø41.5
0.7
Ø41.5
13.5
R2
M4
35
35
9
Ø36 h7
Ø36 h8
60
82
90
Ø12h6
60 0.7
34.7
BSP 1/4” R2
35
35
0.7Thread length 8
35
35
A/F 34 R2 2 2
Ø36 h7
10
Ø36 h8
35
35
20 5.5
82
5.5
Ø36 h7
90
Ø36 h8
M5 50 42.7 32.5 5 33.5 5
82
90
34.7
35
21 21
35
34.7
2 2
35
35
10
20 2 5.5 2 5.5
10
35
Ø36 h7
Ø36 h8
35 250
Stainless foot 4110 0878 80 without holes
82
90
9 30 17 100 14
Ordering No. 4430 0855 80
34.7
9 25 7
35
35
2 2
10
2
20 5.5 5.5
50 32.5 5 285 33.5 5
M5 42.7
35 21 285
250 21
Ø42 h9
7.5
16.28
Ø41.5
55
M4
250
70
35
54
9 30 17 100 14
9
9 9 25 30 177 100 14
A/F 34
2
LZB33-LB-AR0026 5 h7
Ø42 h9
7.5
16.28
Ø41.5
Ø14 j6
55
16.1
16.28M4
54 70
54
Ø42 h9
7.5
Ø41.5
55
9
285
M4
70
9
35 250
9 1230 17
Thread depth 100 14
2
A/F 34 5 h7
5 h7
Ø14 j6
16.1
Ø42 h9
7.5
16.28
Ø41.5
55
M4
70
Ø14 j6
54
16.1
9
12 Thread depth
BSP 1/4”
Ø6.5
A/F 34
5 h7
Ø14 j6
16.1
M5 30
A/F 55
Ø41.5
65
Ø30
5
9
7.5
M5
A/F 55
Ø41.5
65
Ø30
9
BSP 1/4”
Ø19 j6
Ø19 j6
21.5
304.5
9 44 150
9 40 100 14 Ø60
Optional mounting
30
5 14
14
7.5
M5
80
A/F 55
Ø41.5
65
Ø30
80
9
0
R3
Ø60 h8
BSP 1/4”
0
R3
44
Ø60 h8
M6 30
60
44
61.2
42 3
10
Ø19 j6
21.5
M6 30
60 61.2
42 3
14
Foot 80 Flange
Ordering No. 4430 0178 80 Ordering No. 4430 0569 84
0
R3
Ø60 h8
375
62 313
44
M8 6 holes 18 mm DEEP
60 48 75 150
10
5 50 25 100 14
M6 30
Ø60
60 9
61.2 6P
42 3
R36.5
70
375
Ø62 K6
Ø41.5
83 h9
M10
62 313
24
M8 6 holes 18 mm DEEP
60 48 75 150
2.7
LZB33-LB-AR0004 9
6P
LZB33-LB-AR0003 Ø28j6
R36.5
8h7
LZB33-LB-AR0002
LZB33-LB-AR0001
Ø62 K6
Ø41.5
83 h9
M10
31
375
24
62 313
M8 6 holes 18 mm DEEP
60 48 75 150
5 50 25 100 14
Ø60
2.7
9
6P
R36.5
Ø28j6
70
54
8h7
Ø62 K6
Ø41.5
83 h9
M10
24
31
2.7
Ø28j6
8h7
16.1
31
0.50 – 0.71 kW
0.67 – 0.95 hp
LZB42-L-A005 LZB42-L-AR004
14.3
14.3
BSP 1/4” 40
40 40
10.5
BSP BSP
1/4”1/4” 30 209
10.5
10.5
4 4 42 42 167 167
40
14.3
M5
M5
Ø46
j6 j6
41 41
30 30 5 h7
Ø17
1818
4
Reversible
Ø16 j6
A/F 41
Ø16
A/F
10 Ø46Ø46
Ø17
Ø17
18
Ø16
10 5 h75 h7
A/F
10 4 4
10
10 A/F
10 41 BSP 1/2”
BSP 1/4”
M5 M5
A/F A/F
41 41
BSPBSP 1/2”1/4”
BSP
BSP
1/4” 1/2”
j6 j6
41 41
M5
Ø17Ø17
18 18
Ø16Ø16
A/FA/F
10 THREAD DEPTH 15 mm
Ø16 j6
A/F 41
10.6
Ø17
18
10
10 10 THREAD
THREAD DEPTH DEPTH
15 mm 15 mm
10.6
10.6
10.5
BSP BSP
1/4”1/4” 10
60 10 10
THREAD DEPTH
60 15 60
mm
BSP 1/2”
10.610.6
BSP 1/2”
BSP 1/2” THREAD DEPTH
THREAD 15 mm
DEPTH 15 mm
A/F 41
10.6
3
R23
10.510.5
A/F 41 A/F 41 3
4040
R2 R2
40
10.5
h8h8
10
Ø45 h8
60
9696
Ø45
10 10
96
BSP 1/2”
Ø45
60 60
4040
A/F 41 BSP BSP
1/2”1/2” 3838 3
R2
40
38
40 40
A/F A/F
41 41
1010
3 3
R2 R2
h8 h8
10
40
39 2 Ø8.3
96 96
M5 20
Ø45Ø45
26
Ø45 h8
39 39 2 2 Ø8.3 Ø8.3
M5 M5 20 20 26 26
96
47.2
40 40
50
38 38
50 50 47.2 47.2
40
38
10 10
M5 20 39 2
256 26
39 39 2 2 Ø8.3Ø8.3
M5 M5 256 256 20 47.
202 26 26
44 50
44 44 50 50 47.2 47.2
40
40 40
30 28 80
30 30 256 28 28 80 80
Clockwise 44 256 256
Ø60
Ø60 Ø60
5
LZB42-L-A0030 5 5 44 40
44 6 h7
LZB42-L-A0020 6 h7 6 h7
40 40
30 28 80
LZB42-L-A0012 Ø60
30 30 28 28 80 80
5555
j6 j6
Ø46
5 5
M5
Ø30
A/F 55
21.21.
Ø19 j6
Ø60Ø60
Ø19
A/F
Ø46
Ø46
21.5
M5
M5
Reversible
Ø30
Ø30
Ø19
6 h7
A/F
5 5
LZB42-L-AR0025 6 h76 h7
LZB42-L-AR0015
55 55
j6 j6
Ø46
21.521.5
M5 M5
LZB42-L-AR0010
M5Ø30
Ø19Ø19
A/FA/F
Ø19 j6
Ø46
Ø46
21.5
Ø30
Ø30
THREAD
THREAD DEPTH DEPTH
15mm 15mm
A/F
0
R3 R3 14 50
h8h8
118
Ø60 h8
14 14
Ø60
118
118
80
Ø60
5050
4444
80 80 0
50
R3
44
1010
118 50 50
10
M6 0 0
R3 R3
h8 h8
50
M6 M6
118118
60 30 3 Ø10.3
Ø60Ø60
42
Ø60 h8
60 60 30 30 3 35 Ø10.3 Ø10.3
42 423
35 35
50 50
61.2
44 44
61.2 61.2
10 10
50
44
M6
10
M6 M6 60 30 3 Ø10.3
42
35 Ø10.3
Ø10.3
60 60 30 61.
302 42 42 3 3
35 35
326.5
Foot Ordering No. 4430 0178 80
326.5 326.5 61.2 61.2 Flange Ordering No. 4430 0569 84
62 264.5
62 62 264.5 264.5
60
60 60
50 48 80
50 50 48 48 326.5 97 97 80 80
97
62 25 326.5
326.5 27.7 M8 (x6)
5 264.527.7 27.7
Clockwise 5 5
25 25 M8 (x6)M8
DEPTH (x6)
18mm
Ø30
62 60
62
Ø60
264.5
264.5 DEPTH DEPTH
18mm 18mm
Ø30
Ø30
LZB42-L-A0008
Ø60
/F Ø46R36.5 /7F575
Ø60
60 60 8 h7
R36.5 5 75 R36.5 F 75
50 48 97 80
LZB42-L-A0005 8 h7 8 h7
A/A
F
R36.5
/
50 50 482548 97 97 80 80
6 P9
A
27.7 M8 (x6)
5
6 P9
6 P9
h9h9
K6K6
j6 j6
DEPTH 18mm
Reversible
Ø30Ø30
25 25 27.727.7
M10
Ø46
3131
M8 (x6)
M8 (x6)
Ø83 h9
K6
Ø28 j6
Ø60Ø60
Ø28
5 5
Ø83
Ø62
M10
M10
31
Ø46
DEPTH 18mm
DEPTH 18mm
Ø28
Ø30
Ø83
Ø62
Ø62
LZB42-L-AR0006 8 h7
Ø60
/F A/F
R36.5A 75
LZB42-L-AR0004
7
8 h78 h7
6 P96 P9
Ø46Ø46 A
h9 h9
R36.5
K6 K6
j6 j6
6 P9
M10M10
31 31
Ø28Ø28
Ø83Ø83
Ø62Ø62
2.7
Ø83 h9
K6
Ø28 j6
M10
Ø46
31
2.7 2.7
THREAD DEPTH 24mm
Ø62
THREAD
THREAD DEPTH DEPTH
24mm 24mm
2.7
THREAD DEPTH2.7
24mm2.7
THREAD DEPTH
THREAD 24mm
DEPTH 24mm
4000 8000 12000 16000 20000 24000 r/min 1000 2000 3000 4000 5000 6000 7000 r/min 1000 2000 3000 4000 5000 r/min
500 1000 1500 2000 2500 r/min 300 600 900 1200 1500 r/min 200 400 600 800 1000 r/min
100 200 300 400 500 600 r/min 50 100 150 200 250 300 350 r/min 40 80 120 160 200 r/min
Torque
Nm
Power
kW Air cons.
Power l/s
Max
output
Air. cons.
Conversion factors
1 kW = 1.34 hp
Torque
1 Nm = 0.74 Ibf - ft
Torque
at max
power 1 l/s = 2.1 cfm
1 hp = 0.75 kW
1 Ibf-ft = 1.36 Nm
Speed r/min
1 cfm = 0.47 l/s
4000 8000 12000 16000 r/min 1000 2000 3000 4000 5000 r/min 500 1000 1500 2000 2500 3000 3500 r/min
400 800 1200 1600 2000 r/min 200 400 600 800 1000 1200 r/min 100 200 300 400 500 600 700 r/min
100 200 300 400 500 r/min 40 80 120 160 200 240 r/min 20 40 60 80 100 120 140 160 r/min
Torque
Nm
Power
kW Air cons.
Power l/s
Max
output
Air. cons.
Conversion factors
1 kW = 1.34 hp
Torque
1 Nm = 0.74 Ibf - ft
Torque
at max
power 1 l/s = 2.1 cfm
1 hp = 0.75 kW
1 Ibf-ft = 1.36 Nm
Speed r/min
1 cfm = 0.47 l/s
0.59 – 0.84 kW
0.79 – 1.13 hp
M5
LZB46-L-A010 40
A/F 41
Ø16 j6
30
LZB46-L-A005
18
Ø17
Ø46
4
LZB46-L-AV200 5 h7
LZB46-L-AV065
M5
LZB46-L-AV040
A/F 41
Ø16 j6
THREAD DEPTH 15 mm
18
LZB46-L-AV025 Ø17
LZB46-L-AV015
195
-20 UNF
215 215
40
40
Ø45 h8
42 42 173 173 22
10
Ø17
30
172”96
60 40 Ø46
4 40 15
30 30 38 5 h7
40
Ø46 Ø46
4 4 3
R2
10
40
M5
215 5 h7 5 h7
Ø45 h8
A/F 41
20 39 Ø8.3
M5 173 2
Ø16 j6
Ø17
42 215 26
96
18
Ø17
M5
M5
40 47.2
A/F 41
42 50 173
A/F 41
Ø16 j6
BSP 1/4”
Ø16 j6
38
40
18
Ø17
18
Ø17
40 30
Ø46
10
4
30 262
Ø46 5 h7
M5 4 20 39 2 Ø8.3
44
THREAD DEPTH 15 mm 26 5 h7
14.3
M5
50 47.2
40 28 86
BSP 1/4”
A/F 41
THREADTHREAD
DEPTH 15 mm 15 mm
DEPTH
Ø16 j6
M5
30
18
Ø17
A/F 41
195
Ø16 j6
262
18
Ø17
5
Foot Ordering
44 No. 4430 0575 80 Flange
10 Ordering No. 4430 0490 81 22
195 1956 h7
10.5
40 28 86 22 15
22
M5
10 10
A/F 41 BSP 1/2” 60 60 30 THREAD DEPTH 15 mm 3
Ø19 j6
Ø6015
A/F 55
R2 15
21.5
Ø17UNF Ø46
Ø30
40
5 THREAD DEPTH 15 mm
Ø45 h8
3 3
R2 R2 6 h7
10.5
Ø17
96
40
195
40
Ø45 h8
Ø45 h8
M5
10 195
Ø17
-20 UNF
38
22
All versions Clockwise/60 Reversible
40
96
172” -20
96
A/F 41 BSP 1/2” 10
Ø19 j6
40 55
10
21.5
172” Ø46
22
10
Ø30
15
Anti-clockwise THREAD DEPTH 15mm10
LZB46-L-AR0025
38
40
BSP 1/4”
38
A/F
60 Ø8.3
M5 20 39 2 15
Clockwise/ LZB46-L-AR0015R23
10
10
26
LZB46-L-A0030
40
Anti-clockwise
10 BSP 1/4” LZB46-L-A0020
M5 M5
50
LZB46-L-AR0010
2 3 20 47.2
20 Keyed2shaft
39 39 2 (-11) Ø8.3 Ø8.3
Ø45 h8
R 26 26
10.6
40
Ø17
244
96
10
LZB46-L-A0012 47.2
Ø45 h8
50 50 47.2
3/4”-16UNF
BSP
BSP 1/4” 262
Ø17
BSP 1/4”
1/4” THREAD DEPTH 15mm 14
96
26
10.5
38
LZB46-L-AV0030
40
44 22
80 262
38
10
262
40
LZB46-L-AV0020
14.3
40 28 86
44 44
10
30 26 244
50
A/F 41
14.3
14.3
40 20 40 30 28 28 Ø8.3 86 86 Ø60
M5 R39 2 14
A/F 55 3/4”-16UNF
47.2
Ø60 h8
50 26 26
10.5
118
BSP 1/4” 5 30 30
Ø30
47.2 6 h7
10.5
50 80 Ø60 22Ø60
BSP 1/4”
44
50
5 5 262
M5
6 h7
10.5
6 h7
10.5
BSP 1/2” 44
30 262
10
A/F 41
Ø19 j6
0
21.5
R3
Ø30Ø46
M6
14.3
M5
Ø30
M5
44 40 61.2 28 86
Ø60 h8
Ø10.3
118
Ø19 j6
35
A/F 55
Ø19 j6
A/F 55
30 28 86
21.5
21.5
Ø46
Ø46
Ø30
Ø30
44
Ø60
50
30
10 5
Ø60
6 h7
10.5
10
10 5 30
10 10 M6 61.2 332.5 6 h7
10.5
42 3
A/F10
41 10 BSP 1/2” 60 62 270.5 35
Ø19 j6
M5
A/F 55
21.5
Ø46
BSP 1/4”
BSP 1/4” THREADTHREAD
DEPTH 15mm
DEPTH 15mm
Ø30
Reversible
A/F 41
Threaded shaft 244
(-12)
BSP 1/2” 60 48 97 86
Ø19 j6
A/F 55
21.5
Ø46
Ø30
10.6
10
10.6
62 270.5 22
5
80
3/4”-16UNF
10 10
F7
3/4”-16UNF
14 14 26 8 h7
10.5
26
10.5
A/
BSP 1/2” 80 22 22
6 P9
BSP 1/4” 80
THREAD DEPTH 15mm
50 25 27.7
50
A/F 41 0 M8 (x6)
Ø62 K6
Ø28 j6
R3
M10
Ø46
THREAD DEPTH
Ø60 h8
31
BSP 1/2”
BSP 1/2” 5
118
50
Ø30
Ø60
0 0 244
R3
5
R3
F7
8 h7
Ø60 h8
44
Ø60 h8
50
118
10.6
3/4”-16UNF
118
14
A/
244
Ø30
26
10.5
Ø30
R36.5
6 P9
3/4”-16UNF
30 14
10
22
44
44
26
50
80THREAD DEPTH
10.5
50
Ø62 K6
Ø28 j6
M6 24mm 2.7
M10
Ø46
80 3
10
10
BSP 1/2” 60 30 30 42 35
50
42
50
A/F 41 60 42
Ø30 118
60 0 35 35
R3
Ø30
Ø60 h8
118
THREAD DEPTH
44
50
50
30 270.5
M6 332.5 332.5
61.2
10
30 60 48 97 86 Ø10.3
62 62 42 3
270.5 270.5
M6 60 61.2 50 35
Ø10.3
25 27.7 M8 (x6)
60 48 42 3 97
60 60 48 97 35 86 86
THREAD DEPTH
5
50 50Ø3025 25 27.7 27.7 18mm
M8 (x6)M8
Ø60
(x6)
75
5 THREADTHREAD
DEPTH DEPTH 8 h7
5 332.5
5 /F
Ø30
Ø60
R36.5
5
6 P9
332.5
F7
62 270.5
Clockwise/
8 h7 8 h7
Ø62 K6
A/
Ø28 j6
A/
62
M10
Ø46
270.5
R36.5
60 48 97 86
R36.5
31
Anti-clockwise
6 P9
6 P9
Ø62 K6
27.786
Ø28 j6
M10K6
60 5048 97
Ø28 j6
25 M8 (x6)
Ø46
M10
5 Ø46
LZB46-L-A0008
31
31
Ø62
5 THREAD DEPTH
THREAD DEPTH
F7
2.7
A/
5
Ø83 h9
F7
R36.5
8 h7
6 P9
THREADTHREAD
DEPTH DEPTH
LZB46-L-AV0005
A/
2.7
R36.5
Ø28 j6
Ø83 h9 Ø83 h9
6 P9
M10
Ø46
31
Ø62 K6
Ø28 j6
M10
Ø46
Reversible
31
LZB46-L-AR0006
THREAD DEPTH
LZB46-L-AR0004 24mm 2.7
THREAD DEPTH Ø83 h9
24mm 2.7
Ø83 h9
0.60 – 0.84 kW
0.80 – 1.13 hp
Material in parts:
• Casing and front part stainless steel: ISO 683/XIII Type 17,
SS 14 2346, DIN 17440 X12CrNiS188
1)
For Shaft loading curves, see page 14.
NOTE: - If running motors with 100% dry air and no lubrication, performance can be reduced with 5-15% at max output.
- To optimize life time for a lubrication free motor, use lubricated air if the application allows it.
LZB46-RL-A200 LZB46-RL-AR170
LZB46-RL-A065 LZB46-RL-AR050 218
LZB46-RL-A040 LZB46-RL-AR030 218 42 176
LZB46-RL-A025
42 LZB46-RL-AR020 176 40
LZB46-RL-A015
40 LZB46-RL-AR010 30
Ø46
4
LZB46-RL-A010
30 LZB46-RL-AR007 Ø46 5 h7
4
Ø17
LZB46-RL-A005 LZB46-RL-AR004 5 h7
Ø17
M5
A/F 41
M5
Ø16 j6
18
A/F 41
Ø16 j6
18
A
THREAD DEPTH 15 mm
THREAD DEPTH 15 mm
Optional mountings
218 10
6
421060 176 Ø 8.3
60 40
3
30 R2 218
40
Ø46
R2
3 4
Ø45 h8
40
42 218 176 40
5 h7
96
Ø 45 h8
Ø17
Ø45 h8
42
40 176 96
96
38
M5
40
3040
Ø46 40
A/F 41
38
10
40
4
Ø16 j6
30
18
Ø46
10
4 M5 20 5 h7
Ø17
39 2 Ø8.3
M5 20 26 5 h7
Ø17
26 2
A/F 41
50 47.2 28
M5
Ø16 j6
BSP 1/4” 44.2
18
A/F 41
Ø16 j6
THREAD DEPTH 15 mm
18
Foot Ordering No. 4430 0575 81 218 Aluminium Stainless steel
263.5
42 263.5176
Flange Ordering No. 4430 0490 81 Flange Ordering No. 4430 1483 80
44
14.3
40 44 40 THREAD DEPTH 15 mm 28 10 86
14.3
30
40 28 30 THREAD
60 DEPTH
86 15 mm Ø46
4
30 Ø60
5 h7
Ø17
5 Ø60
10.5
3
R2
40
5 10 6 h7
M5
Ø45 h8
All versions 10 6 h7
A/F 41
60
96
M5
Ø16 j6
Ø19 j6
A/F 55
/2”
38
21.5
Ø46
40 40
3
Ø30
R2
Clockwise/10
40
Ø19 j6
A/F 55
21.5
10
Clockwise Reversible
Ø46
3
Ø30
R2
Ø45 h8
Anti-clockwise
96
M5 20
Ø45 h8
10 Ø8.3
39 2 LZB46-RL-A0030
26 LZB46-RL-AR0025
96
THREAD DEPTH 15BSP
mm1/4” 47.2
38
50
40
/4” LZB46-RL-A0020 LZB46-RL-AR0015
38
10
40
BSP 1/4”
THREAD DEPTH 15mm LZB46-RL-A0012 LZB46-RL-AR0010
10
M5 20
39 2 Ø8.3
10.6
60 50 47.2
BSP 1/4” 44
14.3
80 5 44
14.3
10.5
4044 28 86 6 h7
14.3
38
50
40
0
40
30 R3 28 86
10
Ø60 h8
50
M5
A/F 41 0
118
BSP 1/2” R3 Ø60
30
Ø60 h8
M5 20
50 j6
A/F 55
118
539 Ø8.3
21.5
2 Ø60
10.5
Ø46
44
Ø30
Ø19
47.2 26 6 h7
50 5
10.5
10
44
50
6 h7
M5 10
30
M5
A/F 41
10 BSP 1/2” M6
Reversible
10
M6A/F 41
A/F 55
1/2” 3
21.5
42
Ø46
60
Ø30
61.2 Ø10.3 35
Ø19 j6
A/F 55
21.5
263.5 42
Ø46
10 60
Ø30
40 10 BSP 1/4” 28 86
BSP 1/4”
10.5
30
THREAD DEPTH 15mm Ø60
5 14
M5 10.6
A/F 41 80
10.5
10.5
Ø19 j6
A/F 55
14
21.5
50
Ø46
Ø30
0
BSP 1/2” R3 14
Ø60 h8
80
118
5050
30
10
30R 0
Ø60 h8
50
118
61.2 Ø10.3
118
60 42 3
44
35
50
44
50
10
30
M6
10
61.2
Optional mountings
30 3 8 Ø10.3
M6 1460 42 Ø10.3
61.2 35 Ø10.3
60 42 3
80 35
50
50
0
R3
Ø 60 h8
Ø60 h8
118
118
44
50
50
10
30
M6
61.2 Ø10.3 3
60 42 3 35
35 47
4000 8000 12000 16000 20000 24000 r/min 1000 2000 3000 4000 5000 6000 7000 r/min 1000 2000 3000 4000 5000 r/min
500 1000 1500 2000 2500 3000 r/min 300 600 900 1200 1500 r/min 200 400 600 800 1000 r/min
100 200 300 400 500 600 r/min 50 100 150 200 250 300 350 r/min 40 80 120 160 200 240 r/min
Torque
Nm
Power
kW Air cons.
Power l/s
Max
output
Air. cons.
Conversion factors
1 kW = 1.34 hp
Torque
1 Nm = 0.74 Ibf - ft
Torque
at max
power 1 l/s = 2.1 cfm
1 hp = 0.75 kW
1 Ibf-ft = 1.36 Nm
Speed r/min
1 cfm = 0.47 l/s
4000 8000 12000 16000 20000 r/min 1000 2000 3000 4000 5000 6000 r/min 500 1000 1500 2000 2500 3000 3500 r/min
400 800 1200 1600 2000 r/min 200 400 600 800 1200 1600 r/min 100 200 300 400 500 600 700 800 r/min
100 200 300 400 500 r/min 50 100 150 200 250 r/min 20 40 60 80 100 120 140 160 r/min
Torque
Nm
Power
kW Air cons.
Power l/s
Max
output
Air. cons.
Conversion factors
1 kW = 1.34 hp
Torque
1 Nm = 0.74 Ibf - ft
Torque
at max
power 1 l/s = 2.1 cfm
1 hp = 0.75 kW
1 Ibf-ft = 1.36 Nm
Speed r/min
1 cfm = 0.47 l/s
BSP 3/8”
4430 245
89.5
15
Ø60
5 40
16
44
30 40 89.5 6 h7
16
15
Ø60
A/F 50 BSP 1/2” 5 30 89.5
M5
15
Ø60
A/F 55
Ø19 j6
21.5
5 6 h7
M5 Ø30
Ø56
A/F 50 13.5 6 h7
Reversible BSP 1/2”
A/F 55
Ø19 j6
21.5
13.5 A/F 50 BSP 3/8”
1/2”
Ø30
BSP
Ø56
M5
A/F 55
Ø19 j6
21.5
Ø30
Ø56
13.5
THREAD DEPTH 15m m
13.5 13.5 BSP 3/8”
BSP 3/8”
13.5
BSP 3/8”
11
245
THREAD DEPTH 15m m
44
11 15
14
11
30 89.5
15
15
80 Ø60
A/F 50
15
BSP 1/2” 5
Optional mountings 14
14 6 h7
50
0
80 R3
Ø60 h8
A/F 50 BSP 1/2”
118
A/F 50 BSP 1/2”
M5
A/F 55
Ø19 j6
21.5
50
Ø30
44
Ø56
118 50
0
R3
50
Ø60 h8
30
10
13.5
30 R
Ø60 h8
M6
118
13.5
61.2 Ø10.3
44
BSP 3/8”
50
60 42 3
44
50
35
10
THREAD
M6 DEPTH 15m m 30
10
M6
60 61.2 30 Ø10.3
61.2 42 3 Ø10.3
60 3 35
11
42
35
15
313.5
Foot Ordering
62 No. 4430 0178 80 251.5 Flange
14 Ordering No. 4430 0569 84
60 48.2 313.5 74.8 89.5
A/F 50 BSP 1/2” 80 313.5
6250 25 251.5
62 251.5
50
5 60 48.2 0 74.8 89.5
Ø60
R3
Ø30
Ø60 h8
118
50 25
50 25
Clockwise/
44
50
5
Ø60
5
Anti-clockwise
Ø30
Reversible
Ø60
Ø30
10
Ø62 K6
M6 30
M10
LZB54-L-A0025
Ø56
LZB54-L-A0012 LZB54-L-AR0009
Ø62 K6
M10
Ø56
M10
Ø56
LZB54-L-AV0025
LZB54-L-AV0017 THREAD DEPTH
24mm 2.7
LZB54-L-AV0012
313.5
THREAD DEPTHDEPTH
THREAD
24mm24mm 62 2.7 2.7 251.5
60 48.2 74.8 89.5
50 25
M8 (x6)
5 THREAD DEPTH
Ø60
Ø30
18mm
5
F7
M8M8 (x6)
(x6) 8 h7
A/
THREAD
THREAD DEPTH
DEPTH
18mm
18mm
R36.5 R36.5
6 P9
Ø62 K6
75
5
M10
F7
Ø56
8 h7
8 h7
Ø28 j6
R36.5 A/F
A/
31
6 P9
6 P9
Ø28 j6
Ø28 j6
31
31
THREAD DEPTH
24mm 2.7
Ø83 h9
Ø83 h9
Ø83 h9
M8 (x6)
THREAD DEPTH
18mm
75
8 h7
F
A/
R36.5
6 P9
Ø28 j6
31
Ø83 h9
0.80 – 1.20 kW
1.07 – 1.61hp
Material in parts:
• Casing and front part stainless steel: ISO 683/XIII Type 17,
SS 14 2346, DIN 17440 X12CrNiS188
For optional stainless steel motor cell, vane kits and other
accessories see chapter Accessories
Speed
at Air
max Torque Min consumption Shaft
Max out- at max starting Stall Free at max loa-
Output put output torque torque speed output weight ding
code1)
Model
Lubrication free Kw hp r/min Nm lb-ft Nm lb-ft Nm lb-ft r/min l/s cfm kg lb ATEX code Ordering No
Clockwise rotation (Keyed shaft)
LZB54-RL-A180-11 1.20 1.61 10000 1.15 0.85 1.80 1.33 2.30 1.70 17500 22.00 47.00 3.00 6.6 g Ex II 2GD h T4 IIC T110°C 8411 0569 77
LZB54-RL-A050-11 1.20 1.61 2900 4.00 3.00 6.40 4.70 8.00 5.90 5100 22.00 47.00 3.00 6.6 g Ex II 2GD h T4 IIC T110°C 8411 0569 85
LZB54-RL-A030-11 1.20 1.61 1750 6.60 4.90 10.50 7.70 13.20 9.70 3100 22.00 47.00 3.00 6.6 g Ex II 2GD h T4 IIC T110°C 8411 0569 93
LZB54-RL-A020-11 1.20 1.61 1300 8.90 6.60 14.00 10.30 17.80 13.10 2300 22.00 47.00 3.00 6.6 g Ex II 2GD h T4 IIC T110°C 8411 0570 03
LZB54-RL-A010-11 1.18 1.58 630 18 13.30 29 21.00 36 27 1050 22.00 47.00 3.10 6.8 g Ex II 2GD h T4 IIC T110°C 8411 0570 11
LZB54-RL-A007-11 1.18 1.58 380 30 22.00 48 35.00 60 44 650 22.00 47.00 3.10 6.8 g Ex II 2GD h T4 IIC T110°C 8411 0570 29
LZB54-RL-A005-11 1.18 1.58 280 40 30.00 65 48.00 80 59 500 22.00 47.00 3.10 6.8 g Ex II 2GD h T4 IIC T110°C 8411 0570 37
Reversible (Keyed shaft)
LZB54-RL-AR130-11 0.82 1.10 6800 1.15 0.85 1.40 1.03 2.30 1.70 12000 18.00 38.00 3.00 6.6 g Ex II 2GD h T4 IIC T110°C 8411 0570 45
LZB54-RL-AR035-11 0.82 1.10 1960 4.00 3.00 5.10 3.80 8.00 5.90 3700 18.00 38.00 3.00 6.6 g Ex II 2GD h T4 IIC T110°C 8411 0570 52
LZB54-RL-AR020-11 0.82 1.10 1190 6.60 4.90 8.40 6.20 13.20 9.70 2300 18.00 38.00 3.00 6.6 g Ex II 2GD h T4 IIC T110°C 8411 0570 60
LZB54-RL-AR015-11 0.82 1.10 880 8.90 6.60 11.00 8.10 17.80 13 1700 18.00 38.00 3.00 6.6 g Ex II 2GD h T4 IIC T110°C 8411 0570 78
LZB54-RL-AR008-11 0.80 1.07 430 18 13.30 23 17.00 36 27 800 18.00 38.00 3.10 6.8 g Ex II 2GD h T4 IIC T110°C 8411 0570 86
LZB54-RL-AR005-11 0.80 1.07 260 30 22.00 38 28.00 60 44 500 18.00 38.00 3.10 6.8 g Ex II 2GD h T4 IIC T110°C 8411 0570 94
LZB54-RL-AR004-11 0.80 1.07 190 40 30.00 51 38.00 80 59 370 18.00 38.00 3.10 6.8 g Ex II 2GD h T4 IIC T110°C 8411 0571 00
1)
For Shaft loading curves, see page 14.
NOTE: - If running motors with 100% dry air and no lubrication, performance can be reduced with 5-15% at max output.
- To optimize life time for a lubrication free motor, use lubricated air if the application allows it.
245 Ø60
5
44
6 h7
40
16
A/F 55
15
Ø19 j6
Ø60
21.5
Ø30
Ø56
5 218
42 13.5 176 6 h7
40
13.5
BSP 3/8”
A/F 50
Reversible 30 BSP 1/2”
M5
A/F 55
Ø19 j6
4
21.5
Ø30
Ø56
THREAD DEPTH 15m m 245
5 h7
Ø17
13.5 44
M5
11
13.5 40
A/F 41
BSP 3/8”
16
Ø16 j6
18
15
30 89.5
THREAD DEPTH 15m m
15
Ø60
5 14
6 h7
11
A/F 50 DEPTH 15 mm
BSP 1/2” 80
218
THREAD
A/F 50 42BSP 1/2” 176
15
M5
218
50
A/F 55
Ø19 j6
21.5
40 0
Ø30
Ø56
42 176 R3 14
Ø60 h8
30
118
13.5 40 10 Ø46
4
A/F 50 13.5 30BSP 1/2” 80 5 h7
44
60
50
Ø17
5 h7
M5
50
300
Ø17
3
R2 M6THREAD DEPTH 15m m
40
R3 A/F 41
Ø16 j6
41 h8
61.2 Ø10.3
Ø45 h8
118
18
60
M5
42 3
A/FØ60
96
35
Ø16 j6
11
18
44
50
38
40
15
10
10
M6 30
M5 THREAD DEPTH
20 15 mm 61.2 Ø8.3 14 Ø10.3
3960 2 3
26 42
50
THREAD DEPTH 15 mm
47.2 35
80 313.5
A/F 50 BSP 1/2”
62 251.5
Optional mountings 10
50
60 48.2 0 74.8 89.5
R3
60 6
Ø60 h8
263.5 10 Ø 8.3
118
50 25
44 60 3
R2 313.5
40
44
50
40 5 28 86
Ø60
Ø45 h8
Ø30
62 3 251.5
10
R2
96
30
40
40
30
60 M6
Ø 45 h8
74.8
61.2 Ø10.3
38
40
5 60 96
96
42 3
50 25 6 h7 35
10
38
Ø62 K6
40
40
M10
Ø56
M5 5 20
M5
Ø60
39 Ø8.3
10
2” 2
Ø30
47.2 26
Ø19 j6
50
A/F 55
21.5
M5 20
Ø46
Ø8.3
Ø30
39 2 2
BSP 1/4” 47.2 26 28
50
44.2
313.5
Ø62 K6
BSP 1/4”
Foot Ordering No. 4430 0575
DEPTH81 Aluminium Stainless steel
M10
/4”
Ø56
THREAD 263.5
62 251.5
24mm 2.7
44 60 Flange Ordering No. 4430 0490
48.2 74.881 89.5 Flange Ordering No. 4430 1483 80
14.3
30
40 5 28 86 Ø60
Ø60
Ø30
5 30 THREAD DEPTH
10.5
/2”
M5
Ø19 j6
A/F 55
21.5
A/F 55Ø46
M10
Ø56
M5
Ø30
BSP 1/2”
5
118 /F 7
0 8 h7 50
50
Ø19 j6
21.5
0
Ø46
R3
A
Ø30
Ø 60 h8
Ø60 h8
10
R36.5
M8 (x6)
6 P9
118
BSP 1/4”
THREAD DEPTH
Ø28 j6
44
F 7 50
50
18mm
31
24mm
30 2.7 8 h7
M6
A/
60 42
6 P9
35
35 47
Ø28 j6
31
14
Ø83 h9
BSP 1/2”
/F 41 80 14 M8 (x6)
1
BSP 1/2” Foot Ordering No. 4430
80 0178 81 Aluminium Stainless steel
THREAD DEPTH
18mm
Flange Ordering No. 4430 0569 84 Flange Ordering No. 4430 2357 80
50
0
R3
75
Ø60 h8
8 h7
118
F
Ø83 h9
A/
50
0
R3
R36.5
Ø60 h8
44
6 P9
118
50
Ø28 j6
10
44
31
50
30
M6
61.2 Ø10.3
10
60 30 42 3
M6 35
61.2 Ø10.3
60 42 3
35
Ø83 h9
0.79 – 0.82 kW
1.05 – 1.10 hp
For optional stainless steel motor cell, vane kits and other
accessories see chapter Accessories.
1)
For Shaft loading curves, see page 14.
The brake needs minimum 5 bar to release. Performance curves same as standard motors.
NOTE: - If running motors with 100% dry air and no lubrication, performance can be reduced with 5-15% at max output.
- To optimize life time for a lubrication free motor, use lubricated air if the application allows it.
324
44 280
Reversible 40 128 19
13.5 30
13.5 Ø60
5
BSP 3/8”
M5
74
11
A/F 55
324
Ø30
Ø56
15
44 280
40 128 19
BSP 1/2”
13.5 30
A/F 50 THREAD DEPTH 15mm 89.5
13.5 Ø60
5
BSP 3/8”
6 h7
Optional mountings
Ø19 j6
21.5
M5
74
11
A/F 55
Ø30
Ø56
14
15
80
BSP 1/2”
50
0
A/F 50 THREAD DEPTH 15mm R3 89.5
Ø60 h8
118
44
50
6 h7
10
M6 30
60 61.2 Ø10.3
42 3
Ø19 j6
35
21.5
14
Foot Ordering No. 4430 0178 80 Flange Ordering No. 4430 0569 84
80
50
0
R3
Ø60 h8
393.5
118
62 331.5
44
50
60 48.2
10
M6 30
13.5 50 25 128 19
60 61.2 Ø10.3
13.5 42 3
5 35
BSP 3/8”
Reversible with brake
Ø30
LZB54-LB-AR0020
LZB54-LB-AR0012
A/F 70
Ø62 K6
LZB54-LB-AR0009
11
M10
Ø56
15
393.5
62 331.5
BSP 1/2”
THREAD DEPTH 60 48.2
A/F 50 89.5
24mm 2.7 154.8
13.5 50 25 128 19
13.5
5
BSP 3/8” Ø30
M8 (x6)
THREAD DEPTH
A/F 70
18mm
Ø62 K6
11
M10
Ø56
75
15
8 h7
F
A/
R36.5
6 P9
BSP 1/2”
Ø28 j6
31
Ø83 h9
M8 (x6)
THREAD DEPTH
18mm
75
8 h7
F
A/
R36.5
6 P9
Ø28 j6
31
Ø83 h9
4000 8000 12000 16000 20000 r/min 1000 2000 3000 4000 5000 6000 r/min 500 1000 1500 2000 2500 3000 3500 r/min
400 800 1200 1600 2000 2400 r/min 200 400 600 800 1000 1200 r/min 100 200 300 400 500 600 700 r/min
100 200 300 400 500 r/min 50 100 150 200 250 300 r/min 40 80 120 160 200 r/min
kW Nm LZB54-L-A0012 l/s
1.4 350
1.2 300 30
1.0 250 25
0.8 200 20
0.6 150 15
0.4 100 10
0.2 50 5
Torque
Nm
Power
kW Air cons.
Power l/s
Max
output
Air. cons.
Conversion factors
1 kW = 1.34 hp
Torque
1 Nm = 0.74 Ibf - ft
Torque
at max
power 1 l/s = 2.1 cfm
1 hp = 0.75 kW
1 Ibf-ft = 1.36 Nm
Speed r/min
1 cfm = 0.47 l/s
4000 8000 12000 r/min 1000 2000 3000 4000 r/min 400 800 1200 1600 2000 2400 r/min
400 800 1200 1600 2000 r/min 200 400 600 800 1000 r/min 100 200 300 400 500 r/min
50 100 150 200 250 300 350 400 r/min 40 80 120 160 200 240 r/min 20 40 60 80 100 120 140 r/min
kW Nm LZB54-L-AR0009 l/s
1.0
0.8 400
0.6 300 30
0.4 200 20
0.2 100 10
20 40 60 80 100 r/min
Torque
Nm
Power
kW Air cons.
Power l/s
Max
output
Air. cons.
Conversion factors
1 kW = 1.34 hp
Torque
1 Nm = 0.74 Ibf - ft
Torque
at max
power 1 l/s = 2.1 cfm
1 hp = 0.75 kW
1 Ibf-ft = 1.36 Nm
Speed r/min
1 cfm = 0.47 l/s
Compact mounting
Data at air pressure 6.3 bar (91 psi)
Speed Torque Min Air
Max at max at max starting Stall Free consumption
output output output torque torque speed at max Weight Shaft
Model output loading
Lubricated kW hp r/min Nm lb-ft Nm lb-ft Nm lb-ft r/min l/s cfm kg lb code 1) ATEX code Ordering No.
Clockwise rotation (Keyed shaft)
LZB66-L-A0025-15 1.80 2.41 125 139 103 205 151 278 205 230 34 72 5.3 11.7 h Ex II 2GD h T6 IIC T85°C 8411 0600 18
LZB66-L-A0017-15 1.80 2.41 75 227 167 337 249 454 335 145 34 72 5.3 11.7 h Ex II 2GD h T6 IIC T85°C 8411 0600 26
Reversible (Keyed shaft)
LZB66-L-AR0020-15 1.41 1.89 115 117 86 151 111 233 172 200 31 66 5.3 11.7 h Ex II 2GD h T6 IIC T85°C 8411 0601 09
LZB66-L-AR0012-15 1.41 1.89 70 191 141 249 184 382 282 120 31 66 5.3 11.7 h Ex II 2GD h T6 IIC T85°C 8411 0601 17
1)
For Shaft loading curves, see page 14.
M5
A/F 55
Ø19 j6
21.5
Ø30
30
Ø60
14.7
G 3/8”
5
263.3 6 h7
G 3/4” 263.3
44 219.3
18.7
M5
A/F 55 THREAD
44 DEPTH 15mm 219.3
A/F 55
Ø19 j6
40
21.5
Ø30
40
14.7
30
Reversible 30 Ø60
G 3/8” Ø60
G 3/8” 5
13.5 5
G 3/4” 6 h7
6 h7
A/F 55 THREAD DEPTH 15mm 14
13.5
18.7
M5
G 3/8”
A/F 55
Ø19 j6
18.7
M5
21.5
Ø30
80
A/F 55
Ø19 j6
21.5
Ø30
14.7
14.7
50
0
R3
14
Ø60 h8
13.5
118
G 3/4” Optional mounting 14
14.7
13.5
G 3/4”G 3/8”
44
50
A/F 55 THREAD DEPTH 15mm
10
80
M6 30
G 3/4” 60 61.2 Ø10.3
3
50
A/F 55 0 42
R3 35
14
Ø60 h8
118
13.5
14.7
44
13.5
50
13.5 14
G 3/8” 14
10
13.5
G 3/8” M6 80 30
G 3/4” 80 60 61.2 Ø10.3
A/F 55 42 3
333.5 35
50
0
62 R3
14
50
271.5
Flange Ordering No. 4430 0569 84
Ø60 h8
Foot60.5
Ordering No. 4430 0178 R80
30
118
14
Ø60 h8
48 184.3
118
14.7
44
50 M8 (X6)
50
14.7
44
THREAD DEPTH
50
10
5 M6 30 18 mm
10
5
F7
G 3/4” M6 30
61.2 Ø10.3
60 333.5
A/
A/F 55 42 3 Ø10.3
G 3/4” 60 61.2 35
62 271.5 3
R 36.5
A/F 55 42
6 P9
35
60.5 48 184.3
Ø62 K6
M10
M8 (X6)
Ø30
Ø60
50
THREAD DEPTH
5 18 mm
5
F7
A/
Clockwise THREAD 333.5 R 36.5
6 P9
DEPTH 62 333.5 Ø83 h9
271.5
LZB66-L-A0025-11 24mm 2.7
Ø62 K6
62
60.5 271.5
48 184.3
M10
Ø30
Ø60
LZB66-L-A0017-11 60.5
50 48 184.3 8h M8 (X6)
LZB66-L-A0012-11 50 M8 (X6) DEPTH
THREAD
5 THREAD
18 mm DEPTH
5
F5 7
18 mm
Ø28 j6
5
THREAD
FA/7
Reversible
31
DEPTH
A/
Ø83 h9
R 36.5
24mm 2.7
6 P9
LZB66-L-AR0020-11
R 36.5
6 P9
Ø62 K6
LZB66-L-AR0012-11
M10
Ø30
Ø60
Ø62 K6
8h
M10
Ø30
Ø60
LZB66-L-AR0009-11
Ø28 j6
31
THREAD 338.6
DEPTH
THREAD Ø83 h9
24mm
DEPTH 100.8 2.7
Ø83 h9
24mm 2.7
55.6
Ø808 h11
h
45.2 8h
5/16” -18 UNC (x6)
38.1 THREAD DEPTH 18mm
Ø28 j6
31
Ø28 j6
338.6
31
2.9
100.8
R28.6
55.6
Ø68.3- 00.2
Ø60 h10
Ø80 h11
Ø20
45.2
5/16” -18 UNC (x6)
38.1 THREAD DEPTH 18mm
M5
M6 (x6)
THREAD DEPTH 12mm
2.9 338.6
338.6
R28.6
26
Clockwise 100.8
THREAD DEPTH 15mm
Ø68.3- 00.2
Ø60 h10
100.8 A/F 72
55.6
Ø20
M6 (x6)
45.2
THREAD DEPTH 12mm
2.9 26
2.9 THREAD DEPTH 15mm
LZB66-L-AR0020-15
R28.6
Ø60 h10
Ø68.3- 00.2 0
LZB66-L-AR0012-15
Ø60 h10
Ø20
Ø20
4.762 h7
M5
M6 (x6)
THREAD DEPTH 12mm
M5
(x6)
THREAD DEPTH 12mm
M621.2
4.762 h7
4.762 h7
21.2
21.2
Ø19.05- 00.013
Ø19.05- 00.013
1.79 kW
2.40 hp
LZB66-L-A0025-16
52 35
Ø 60
52
371
G 3/8"
18.7
14.7 EXH
3/4" Square
G 3/4" Ø 27
A/F 55
Ø 65.7
LZB66-L-A0013-16
52 35 Ø 60
Ø 86
52
424
G 3/8" 140
18.7
14.7 EXH
15.5
8.5 4.5 M6
23 20
Ø10
G 3/4" 3/4" Square
A/F 55
27
65.7
1.43 – 1.87 kW
1.91 – 2.51hp
Material in parts:
For optional stainless steel motor cell, vane kits and other
accessories see chapter Accessories.
Speed
at Air
max Torque Min consumption
Max out- at max starting Stall Free at max
Output put output torque torque speed output weight
Shaft
Model loading
Lubrication free Kw hp r/min Nm lb-ft Nm lb-ft Nm lb-ft r/min l/s cfm kg lb code1) ATEX code Ordering No
Clockwise rotation (Keyed shaft)
LZB66-RL-A180-11 1.87 2.51 8200 2.20 1.62 3.20 2.40 4.40 3.20 16000 34.00 72.00 3.4 7.5 g Ex II 2GD h T4 IIC T110°C 8411 0604 32
LZB66-RL-A050-11 1.87 2.51 2400 7.60 5.60 11.30 8.30 15.20 11.20 4500 34.00 72.00 3.4 7.5 g Ex II 2GD h T4 IIC T110°C 8411 0604 40
LZB66-RL-A030-11 1.87 2.51 1440 12.50 9.20 18.60 13.70 25.00 18.40 2700 34.00 72.00 3.4 7.5 g Ex II 2GD h T4 IIC T110°C 8411 0604 57
LZB66-RL-A020-11 1.87 2.51 1060 17.00 12.50 25.00 18.40 34.00 25.00 2000 34.00 72.00 3.4 7.5 g Ex II 2GD h T4 IIC T110°C 8411 0604 65
LZB66-RL-A010-11 1.83 2.45 510 34 25.00 51 38.00 68 50 950 34.00 72.00 3.5 7.7 g Ex II 2GD h T4 IIC T110°C 8411 0604 73
LZB66-RL-A007-11 1.83 2.45 310 57 42.00 84 62.00 114 84 600 34.00 72.00 3.5 7.7 g Ex II 2GD h T4 IIC T110°C 8411 0604 81
LZB66-RL-A005-11 1.83 2.45 230 77 57.00 113 83.00 154 114 440 34.00 72.00 3.5 7.7 g Ex II 2GD h T4 IIC T110°C 8411 0604 99
Reversible (Keyed shaft) Ex II 2GD h T4 IIC T110°C
LZB66-RL-AR130-11 1.46 1.96 7500 1.90 1.40 2.40 1.80 3.80 2.80 13500 31.00 66.00 3.4 7.5 g Ex II 2GD h T4 IIC T110°C 8411 0605 09
LZB66-RL-AR035-11 1.46 1.96 2200 6.40 4.70 8.30 6.10 12.80 9.40 3900 31.00 66.00 3.4 7.5 g Ex II 2GD h T4 IIC T110°C 8411 0605 17
LZB66-RL-AR020-11 1.46 1.96 1320 10.50 7.70 13.05 10.00 21.00 15.50 2400 31.00 66.00 3.4 7.5 g Ex II 2GD h T4 IIC T110°C 8411 0605 25
LZB66-RL-AR015-11 1.46 1.96 970 14.30 10.50 18.05 13.60 29.00 21 1750 31.00 66.00 3.4 7.5 g Ex II 2GD h T4 IIC T110°C 8411 0605 33
LZB66-RL-AR008-11 1.43 1.92 470 29 21.00 37 27.00 58 43 850 31.00 66.00 3.5 7.7 g Ex II 2GD h T4 IIC T110°C 8411 0605 41
LZB66-RL-AR005-11 1.43 1.92 290 48 35.00 62 46.00 96 71 500 31.00 66.00 3.5 7.7 g Ex II 2GD h T4 IIC T110°C 8411 0605 58
LZB66-RL-AR004-11 1.43 1.91 210 64 47.00 84 62.00 128 94 370 31.00 66.00 3.5 7.7 g Ex II 2GD h T4 IIC T110°C 8411 0605 66
1)
For Shaft loading curves, see page 14.
NOTE: - If running motors with 100% dry air and no lubrication, performance can be reduced with 5-15% at max output.
- To optimize life time for a lubrication free motor, use lubricated air if the application allows it.
M5
A/F 55
Ø19 j6
21.5
Ø30
14.7
218
G 3/4” 263.3
42
A/F 55 176
THREAD DEPTH 15mm
40 44 219.3
30 40 Ø46
Reversible
4
30 5 h7
Ø17
Ø60
13.5 G 3/8”
M5
5
6 h7
A/F 41
13.5 14
Ø16 j6
G 3/8”
18
80
18.7
M5
A/F 55
Ø19 j6
21.5
Ø30
50
14.7
0
R3
14
Ø60 h8
218
118
THREAD DEPTH 15 mm
42 176
14.7
44
218
50
40 G 3/4”
4255 17615mm
10
Ø46
4
5 h7
M5
Ø17
3
R2
40
A/F 41
Ø16 j6
13.5
Ø45 h8
18
M5
96
14
A/F 41
13.5
Ø16 j6
G 3/8”
18
38
40
80
333.5
10
62 271.5
THREAD DEPTH
20 15 mm
50
M5
60.5 39 248 30 Ø8.3 184.3
26R
14
Ø60 h8
47.2
118
50
THREAD DEPTH 15 mm 50 M8 (X6)
14.7
THREAD DEPTH
44
50
5 18 mm
Optional mountings
5
10
F7
10
30
A/
60 M6 6
263.5 10 61.2 Ø10.3Ø 8.3
R 36.5
G 3/4” 60 3
6 P9
44 A/F 55 60 42
3 35
R2
Ø62 K6
40
M10
Ø30
28
Ø60
40 86
Ø45 h8
3
R2
96
30
40
40
Ø 45 h8
Ø60
Ø45 h8
38
40
5 96
96
6 h7
10
THREAD
38
40
40
DEPTH Ø83 h9
M5 20 2.7 333.5
24mm
M5
39 Ø8.3
10
2” 2
47.2 62 26
271.5
Ø19 j6
50
A/F 55
21.5
M5 20
Ø46
Ø8.3 8h
Ø30
BSP 1/4” 18 mm
5
Foot Ordering No. 4430 0575 81 Aluminium Stainless steel
31
/4”
R 36.5 Ø28 5
263.5
Flange Ordering No. 4430 0490 81 Flange Ordering No. 4430 1483 80
A/
44
14.3
6 P9
40 28 86
44
14.3
Ø62 K6
30
M10
Ø30
Ø60
40 28 86 Ø60
5 30
10.5
Ø60 6 h7 8
5 14 338.6 Ø10.3
10.5
/2”
M5
Ø83 h9
A/F 55
21.5
55.624mm 2.7
A/F 55Ø46
M5
Ø30
Ø19 j6
21.5
Ø46
Ø 60 h8
Ø60 h8
118
BSP 1/4”
44
Ø28 j6
2.9
50
50
31
BSP 1/4”
R28.6
30
Ø68.3- 00.2
Ø60 h10
M6
61.2
Ø20
M6 (x6)
THREAD DEPTH 12mm
14
BSP 1/2”
/F 41 80 14 338.6 26
THREAD DEPTH 15mm
A/F 72
1
BSP 1/2” Foot Ordering No. 4430
80 0178 81 100.8Aluminium Stainless steel
Flange Ordering No. 4430 0569 84 Flange Ordering No. 4430 2357 80
50
55.6 0
R3 4.762 h7 Ø80 h11
Ø60 h8
118
45.2
50
38.1
44
21.2
50
10
44
2.9
50
30 Ø19.05- 00.013
M6
R28.6
61.2 Ø10.3
10
60 30 42 3
Ø68.3- 00.2
Ø60 h10
M6 35
Ø20
61.2 Ø10.3
60 42 3
35
M5
M6 (x6)
THREAD DEPTH 12mm
26
THREAD DEPTH 15mm
A/F 72
4.762 h7
21.2
Ø19.05- 00.013
4000 8000 12000 16000 r/min 1000 2000 3000 4000 5000 r/min 500 1000 1500 2000 2500 3000 r/min
0.4 10 15 15 30
1.2 9 45 1.20.4 15 45
15 0.4 15
0.4 3 15 0.4 5 15
1.6
0.8 60
60 30 1.60.8120
200 30 0.8 200 30
1.2
0.4 45
30 45
15 1.20.4 90100 45 15 0.4 100 15
0.8 30 30 0.8 60 30
100 200 300 400 500 r/min 50 100 150 200 250 r/min 30 60 90 120 150 r/min
0.4 15 15 0.4 30 15
0.8 300
1.6 30 1.60.8400100 30 0.8 200 30
1.2
0.4 300
150 45
15 1.20.430050 45 15 0.4 100 15
With right50angle
100 head
150 200 250 r/min 30 60 90 120 150 r/min
4000 8000 12000 r/min 1000 2000 3000 4000 r/min 500 1000 1500 2000 2500 r/min
400 800 1200 1600 2000 r/min 200 400 600 800 1000 r/min 100 200 300 400 500 600 r/min
50 100 150 200 250 300 350 400 r/min 40 80 120 160 200 240 r/min 20 40 60 80 100 120 140 r/min
kW Nm LZB66-L-AR0009 l/s
1.5 500
1.2 400 40
0.9 300 30
0.6 200 20
0.3 100 10
20 40 60 80 100 r/min
Torque
Nm
Power
kW Air cons.
Power l/s
Max
output
Air. cons.
Conversion factors
1 kW = 1.34 hp
Torque
1 Nm = 0.74 Ibf - ft
Torque
at max
power 1 l/s = 2.1 cfm
1 hp = 0.75 kW
1 Ibf-ft = 1.36 Nm
Speed r/min
1 cfm = 0.47 l/s
369.3
Clockwise 57 312.3
44.5 48.2
25 130 45
R38.1
Ø85.5 h10
M6
Ø88.9 h9
23
Ø62.1
Ø100
THREAD DEPTH
A/F 70 16mm 2.7 A/
F8
0
Reversible
6.35 h7
19.35
28.15
19.35
Ø 77 Ø25.4 j6
70
12.43
23
BSP 1/2”OR NPTF 1/2”–14 Ø 40 Ø 95
127.5˚ 127.5˚
M5 Depth 10 (x3)
M32x1.5 Depth 15 10
500 1000 1500 2000 2500 r/min 100 200 300 400 500 600 700 800 r/min 100 200 300 400 500 600 700 r/min
100 200 300 400 500 r/min 50 100 150 200 250 300 350 r/min 40 80 120 160 200 r/min
kW Nm LZB77-L-A0017 l/s
3.0
2.5 750 75
2.0 600 60
1.5 450 45
1 300 30
0.5 150 15
Reversible (AR)
kW Nm LZB77-L-AR024 l/s kW Nm LZB77-L-AR007 l/s kW Nm LZB77-L-AR006 l/s
2.5 2.5 150 2.5 150
500 1000 1500 2000 2500 r/min 100 200 300 400 500 600 700 800 r/min 100 200 300 400 500 600 700 r/min
100 200 300 400 500 r/min 50 100 150 200 250 300 350 r/min 40 80 120 160 200 r/min
kW Nm LZB77-L-AR0015 l/s
2.5 Torque
Nm
Power
2.0 600 kW Air cons.
80 l/s
Power
Max
output
1.5 450 60
Air. cons.
1.0 300 Conversion factors
40
1 kW = 1.34 hp
0.5 150 20 Torque
1 Nm = 0.74 Ibf - ft
Torque
at max
power 1 l/s = 2.1 cfm
Key chuck and quick chuck for LZB22/33-12 Threaded shafts for re-building standard motors
Body
Motor Thread dimension Ordering No.
diameter Capacity
Chuck type Mount mm mm Ordering No. LZB42-L-A200 1/2"–20 UNF 4430 0868 80
Key chuck 3/8"-24 UNF 30 0 - 6.5 4021 0283 00 LZB42-L-A065 1/2"–20 UNF 4430 0868 80
Key chuck 3/8"-24 UNF 36 2.0 - 10.0 4021 0416 00 LZB42-L-A040 1/2"–20 UNF 4430 0868 81
Key chuck 3/8"-24 UNF 46 2.0 - 13.0 4021 0289 00 LZB42-L-A025 1/2"–20 UNF 4430 0868 82
Key chuck 1/2"-20 UNF 42.8 1.5 - 13 4021 0289 01 LZB42-L-A015 1/2"–20 UNF 4430 0869 80
Quick chuck 3/8"-24 UNF 34 0 - 6.5 4021 0401 00 LZB42-L-A010 1/2"–20 UNF 4430 0869 80
Quick chuck 3/8"-24 UNF 36 0 - 10.0 4021 0402 00 LZB42-L-A005 1/2"–20 UNF 4430 0869 80
Quick chuck 3/8"-24 UNF 36 2.0 - 13.0 4021 0403 00 LZB42-L-A0030 3/4"–16 UNF 4430 0870 80
LZB42-L-A0020 3/4"–16 UNF 4430 0870 80
LZB42-L-A0012 3/4"–16 UNF 4430 0870 80
LZB54-L / LZB66-A180 1/2"–20 UNF 4430 0871 80
LZB54-L / LZB66-A050 1/2"–20 UNF 4430 0871 80
LZB54-L / LZB66-A030 1/2"–20 UNF 4430 0871 81
LZB54-L / LZB66 -A020 1/2"–20 UNF 4430 0871 82
LZB54-L / LZB66-A010 3/4"–16 UNF 4430 0870 80
LZB54-L / LZB66- A007 3/4"–16 UNF 4430 0870 80
LZB54-L / LZB66-A005 3/4"–16 UNF 4430 0870 80
Collet chuck and collets for LZB22-12 to LZB33-12 Safety remote control
Capacity Type Ordering No.
Type mm in Ordering No. Safety remote control 4430 2218 80
Collet holder cpl. 4110 0844 90
Collet 3 4150 0081 00
Collet 5 4150 0075 01
Collet 6 4150 0075 00
Collet 8 5/16" 4150 0074 00
Collet 1/8" 4150 0082 00
Collet 5/32" 4150 0648 00
Collet 3/16" 4150 0649 00
Collet 1/4" 4150 0076 00
Stainless steel motor cell, LZB14 Stainless steel motor cell, LZB22
Air Motor Motor cell Air Motor Motor cell
Model Ordering No. Ordering No. Model Ordering No. Ordering No.
Clockwise rotation (Key shaft) Clockwise rotation (Key shaft)
LZB14-RL-A190-11 8411 0122 09 4430 2194 80 LZB22-RL-A120-11 8411 0219 11 4430 2304 83
LZB14-RL-A048-11 8411 0122 17 4430 2194 80 LZB22-RL-A049-11 8411 0219 29 4430 2304 83
LZB14-RL-A029-11 8411 0122 25 4430 2194 80 LZB22-RL-A036-11 8411 0219 37 4430 2305 83
LZB14-RL-A12-11 8411 0122 33 4430 2194 80 LZB22-RL-A022-11 8411 0219 45 4430 2304 83
LZB14-RL-A007-11 8411 0122 41 4430 2194 80 LZB22-RL-A011-11 8411 0219 52 4430 2304 83
Reversible (Key shaft) LZB22-RL-A008-11 8411 0219 60 4430 2305 83
LZB14-RL-AR140-11 8411 0122 58 4430 2194 84 LZB22-RL-A005-11 8411 0219 78 4430 2304 83
LZB14-RL-AR034-11 8411 0122 66 4430 2194 84 Reversible (Key shaft)
LZB14-RL-AR020-11 8411 0122 74 4430 2194 84 LZB22-RL-AR126-11 8411 0220 83 4430 2304 84
LZB14-RL-AR008-11 8411 0122 82 4430 2194 84 LZB22-RL-AR028-11 8411 0220 75 4430 2304 84
LZB14-RL-AR005-11 8411 0122 90 4430 2194 84 LZB22-RL-AR021-11 8411 0220 16 4430 2305 84
LZB22-RL-AR013-11 8411 0220 67 4430 2304 84
LZB22-RL-AR006-11 8411 0220 59 4430 2304 84
LZB22-RL-AR005-11 8411 0220 08 4430 2305 84
LZB22-RL-AR003-11 8411 0220 91 4430 2304 84
Stainless steel motor cell, LZB34 Stainless steel motor cell, LZB46
Air Motor Motor cell Air Motor Motor cell
Model Ordering No. Ordering No. Model Ordering No. Ordering No.
Clockwise rotation (Key shaft) Clockwise rotation (Key shaft)
LZB34-RL-A210-11 8411 0338 41 4430 2291 83 LZB46-RL-A200-11 8411 0472 15 4430 1076 83
LZB34-RL-A060-11 8411 0338 58 4430 2291 83 LZB46-RL-A065-11 8411 0472 23 4430 1076 83
LZB34-RL-A033-11 8411 0338 66 4430 2291 83 LZB46-RL-A040-11 8411 0472 31 4430 1076 83
LZB34-RL-A026-11 8411 0338 74 4430 2290 83 LZB46-RL-A025-11 8411 0472 49 4430 1206 80
LZB34-RL-A013-11 8411 0338 82 4430 2291 83 LZB46-RL-A015-11 8411 0470 82 4430 1076 83
LZB34-RL-A007-11 8411 0338 90 4430 2291 83 LZB46-RL-A010-11 8411 0471 08 4430 1076 83
LZB34-RL-A005-11 8411 0339 08 4430 2290 83 LZB46-RL-A005-11 8411 0471 16 4430 1206 80
Reversible (Key shaft) LZB46-RL-A0030-11 8411 0471 24 4430 1076 83
LZB34-RL-AR150-11 8411 0339 16 4430 2291 84 LZB46-RL-A0020-11 8411 0471 32 4430 1076 83
LZB34-RL-AR043-11 8411 0339 24 4430 2291 84 LZB46-RL-A0012-11 8411 0471 40 4430 1206 80
LZB34-RL-AR024-11 8411 0339 32 4430 2291 84 Reversible (Key shaft)
LZB34-RL-AR019-11 8411 0339 40 4430 2290 84 LZB46-RL-AR170-11 8411 0472 56 4430 1076 84
LZB34-RL-AR009-11 8411 0339 57 4430 2291 84 LZB46-RL-AR050-11 8411 0472 64 4430 1076 84
LZB34-RL-AR005-11 8411 0339 65 4430 2291 84 LZB46-RL-AR030-11 8411 0472 72 4430 1076 84
LZB34-RL-AR004-11 8411 0339 73 4430 2290 84 LZB46-RL-AR020-11 8411 0472 80 4430 1206 84
LZB46-RL-AR010-11 8411 0471 57 4430 1076 84
For the complete range LZB34-RLB- Ordering No. 4430 2291 84 LZB46-RL-AR007-11 8411 0471 65 4430 1076 84
LZB46-RL-AR004-11 8411 0471 73 4430 1206 84
LZB46-RL-AR0025-11 8411 0471 81 4430 1076 84
LZB46-RL-AR0015-11 8411 0471 99 4430 1076 84
LZB46-RL-AR0010-11 8411 0472 07 4430 1206 84
Stainless steel motor cell, LZB54 Stainless steel motor cell, LZB66
Air Motor Motor cell Air Motor Motor cell
Model Ordering No. Ordering No. Model Ordering No. Ordering No.
Clockwise rotation (Key shaft) Clockwise rotation (Key shaft)
LZB54-RL-A180-11 8411 0569 77 4430 2375 83 LZB66-RL-A180-11 8411 0604 32 4430 2478 80
LZB54-RL-A050-11 8411 0569 85 4430 2375 83 LZB66-RL-A050-11 8411 0604 40 4430 2478 80
LZB54-RL-A030-11 8411 0569 93 4430 2312 83 LZB66-RL-A030-11 8411 0604 57 4430 2483 80
LZB54-RL-A020-11 8411 0570 03 4430 2375 83 LZB66-RL-A020-11 8411 0604 65 4430 2478 80
LZB54-RL-A010-11 8411 0570 11 4430 2375 83 LZB66-RL-A010-11 8411 0604 73 4430 2478 80
LZB54-RL-A007-11 8411 0570 29 4430 2312 83 LZB66-RL-A007-11 8411 0604 81 4430 2483 80
LZB54-RL-A005-11 8411 0570 37 4430 2375 83 LZB66-RL-A005-11 8411 0604 99 4430 2478 80
Reversible (Key shaft) Reversible (Key shaft)
LZB54-RL-AR130-11 4430 2375 84 LZB66-RL-AR130-11 8411 0605 09 4430 2478 81
LZB54-RL-AR035-11 8411 0570 52 4430 2375 84 LZB66-RL-AR035-11 8411 0605 17 4430 2478 81
LZB54-RL-AR020-11 8411 0570 60 4430 2312 84 LZB66-RL-AR020-11 8411 0605 25 4430 2483 81
LZB54-RL-AR015-11 8411 0570 78 4430 2375 84 LZB66-RL-AR015-11 8411 0605 33 4430 2478 81
LZB54-RL-AR008-11 8411 0570 86 4430 2375 84 LZB66-RL-AR008-11 8411 0605 41 4430 2478 81
LZB54-RL-AR005-11 8411 0570 94 4430 2312 84 LZB66-RL-AR005-11 8411 0605 58 4430 2483 81
LZB54-RL-AR004-11 8411 0571 00 4430 2375 84 LZB66-RL-AR004-11 8411 0605 66 4430 2478 81
A B C D 0.36 – kW motor
Silencers No-load speed
Anechoic room Noise level
Interval of 1 m Measure dB(A)
A B C D
Sinter bronze LBB ECSB-2 Blue
Motor Ordering No. Ordering No. Ordering No. Ordering No.
None 94
LZB14 9090 0507 00 - 9090 2100 01 -
LZB22 A, AV 9090 0508 00 4250 1878 83 9090 2100 01 -
LZB22 AR, LR 9090 0507 00 4250 1878 83 9090 2100 01 -
LZB33, LZB34 9090 0508 00 - 9090 2100 01 -
LZB42-L 9090 0510 00 - 9090 2100 01 0803 5011 07 Silencer only 77
LZB46-L 9090 0510 00 - 9090 2100 01 0803 5011 07
LZB54-L 9090 0510 00 - 9090 2100 01 0803 5011 07
LZB66-L - - 9090 2100 02 -
LZB77-L - Build in silencer - -
LZL03 - - 9090 2100 01 0803 5011 06
LZL05 - - 9090 2100 02 0803 5011 07 Hose only 84
NOTE: The noise damping and power loss values are approximate. The ECSB-2 silencer –01 Hose with silencer 75
has 1/2”and the –02 has 1” threaded port. They need to be connected to the motor via
tube or hose with suitable connections.
LZL vane motors are available in five sizes, offering outputs of 1.05 kW, 1.3 kW, 2.3 kW, 3.4 kW and 5.2 kW, respectively.
They are designed to give outstanding starting and low speed performance. This is achieved by using a six vane motor and by
optimum vane/cylinder sealing – obtained through a combination of ‘vane air’ and interconnecting pins.
Featuring few components, these motors are ruggedly constructed and offer a long service life.
Restrictors
Figure 3
Clockwise rotation – the smaller restrictor (1) is fitted in the
inlet port and the larger restrictor (2) in the outlet port
(see Figure 3). This is how the motor is delivered.
Fa LZL 35 A = 25 mm
(N) LZL 25 A = 25 mm
LZL 15 A = 25 mm
1200
LZL 05 A = 20 mm
LZL 03 A = 20 mm
1000
800
600
400
200
Fr
200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 (N)
LZL 35 A = 25 mm
LZL 25 A = 25 mm
LZL 15 A = 25 mm
LZL 05 A = 20 mm
LZL 03 A = 20 mm Figure 2
The power motors come in all five sizes and are designed to give
4. 1. 2.
highest power and still maintain good low speed characteristics.
These motors are delivered with lube free vanes and can
theretofore operate without lubrication.
• Reliable starting
• Long working life and easy servicing 1. Rubber hose valves for venting bearing and seals.
2. Vane pins.
3. Double seals.
EX certification valid for fixture mounted use only with a 4. Stainless steel bushing.
maximum surrounding temperature of +40°C (104°F). 5. Aluminum front with stainless steel screws.
* Motors without restrictor plates in the air in- and outlet, the motor should not be run above max allowed speed.
** Max allowed speed for the specified ATEX code is 5000 rpm.
Max Air
Power at Torque at 3000 Stall allowed consumption at
3000 rpm rpm torque speed 3000 rpm Weight
Model
Lubrication free kW hp Nm lb-ft Nm lb-ft r/min l/s cfm kg lb ATEX code Ordering No.
LZL03-L-M-AC 0.41 0.55 1.3 0.95 3.3 2.4 3000 16 34 2.9 6.4 Ex II 2GD h T6 IIC T85oC X 8411 1010 06
LZL03-L-M-IEC 0.41 0.55 1.3 0.95 3.3 2.4 3000 16 34 3.8 8.4 Ex II 2GD h T6 IIC T85oC X 8411 1010 14
LZL03-L-M-NEMA 0.41 0.55 1.3 0.95 3.3 2.4 3000 16 34 3.9 8.6 Ex II 2GD h T6 IIC T85oC X 8411 1010 22
Unrestricted* 1.0 1.3 3.3 2.4 3.8 2.8 3000 24 51
LZL05-L-M-AC 0.63 0.84 2.0 1.5 5.8 4.3 3000 25 52 3.9 8.6 Ex II 2GD h T6 IIC T85oC X 8411 1010 63
LZL05-L-M-IEC 0.63 0.84 2.0 1.5 5.8 4.3 3000 25 52 4.8 10.6 Ex II 2GD h T6 IIC T85oC X 8411 1010 71
LZL05-L-M-NEMA 0.63 0.84 2.0 1.5 5.8 4.3 3000 25 52 4.9 10.8 Ex II 2GD h T6 IIC T85oC X 8411 1010 89
Unrestricted* 1.7 2.2 5.3 3.9 5.8 4.3 3000 35 74
* Motor without restrictor plates in the air in- and outlet, the motors should not be run above max allowed speed.
1. 2.
Stainless steel motors
The material used in all external parts is ISO 683/Xlll Type 17,
SS 14 2346, DIN 17440 X 12CrNiS188.
Max Air
Power at Torque at 3000 Stall allowed consumption at
3000 rpm rpm torque speed 3000 rpm Weight
Model
Lubrication free kW hp Nm lb-ft Nm lb-ft r/min l/s cfm kg lb ATEX code Ordering No.
LZL05-RL-P-IEC 0.63 0.84 2.0 1.5 5.8 4.3 3000 25 52 6.1 13.4 Ex II 2GD h T4 IIC T110oC 8411 1010 97
LZL05-RL-P-NEMA 0.63 0.84 2.0 1.5 5.8 4.3 3000 25 52 6.1 13.4 Ex II 2GD h T4 IIC T110oC 8411 1011 01
Unrestricted* 1.7 2.2 5.3 3.9 5.8 4.3 3000 35 74
* Motor without restrictor plates in the air in- and outlet, the motors should not be run above max allowed speed.
G A
0.2
0.0
Rev.Ver
Rev.Ver
K A
J
LZL_CATALOG
LZL03-L-P-AC
I H
Drawing name
Model name
F F B
90°(4x)
R
E
P
L
D F-F F
45°
S
C
T N
M
LZL05-L-P-HUB
15°(2x)
U
O
A E
F
copied, used for manufacturing or communicated to any other person or company.
This document is our property and shall not without our permission be altered,
Tolerances, if not - - - - -
indicated, according to:
AC-STD - - - - -
Name Secrecy class
VANE MOTOR LZL03-L-P-AC LZL03
Material
- 1102 K/-
CAD
- Pro/E G
Scale Format Family Compare Drawing owner
1:1 A2 - 8411 1009 88
Drawn
D Öhlund
Blank
-
Replaces
- TOO
Cons.class Rev Status Designation Sheet 1 (1)
0 - - - - 1295 K/- 0 In Work
8411 1009 70
Transferred from
Mass/Volume Date
Note Pos. Modified from Date Intr. - - 2016-05-23
Model A B C D E F G H I J K L M N O P R S T U
LZL03-L-M/P-AC mm 124 Ø105 Ø70 j6 Ø16 j7 18 5 h9 40 30 2.0 2.5 8.5 M5x15 65 BSP ⅜” 36 Ø69 Ø85 Ø7 1 -
LZL03-L-M/P-IEC mm 124 Ø160 Ø110 j6 Ø14 j7 16 5 h9 30 20 2.0 3.5 8.5 M5x15 65 BSP ⅜” 36 Ø69 Ø130 Ø10 - -
LZL03-L-M/P-NEMA mm 124 Ø165.1 Ø114.3 Ø15.875 17.85 4.75 51.5 31.75 1.7 3.175 10 M5x15 65 BSP ⅜” 36 Ø69 Ø149.225 ⅜”-16 UNC 1 -
LZL03-L-M/P-NEMA inch 4.88 Ø6.5 Ø4.5 Ø0.625 0.703 0.187 2.03 1.25 0.07 0.125 0.39 M5x15 2.56 BSP ⅜” 1.42 Ø2.72 Ø5.875 ⅜”-16 UNC 0.04 -
LZL05-L-P-AC mm 152 Ø105 Ø70 j6 Ø18 j7 20.5 6 h9 40 30 3.0 2.5 8.5 M5x15 81 BSP ½” 44 Ø76 Ø85 Ø7 - -
LZL05-L-M-AC mm 152 Ø105 Ø70 j6 Ø16 j7 18 5 h9 40 30 2.0 2.5 8.5 M5x15 81 BSP ½” 44 Ø76 Ø85 Ø7 0.5 -
LZL05-L-M/P-IEC mm 152 Ø160 Ø110 j6 Ø14 j7 16 5 h9 30 20 2.0 3.5 8.5 M5x15 81 BSP ½” 44 Ø76 Ø130 Ø10 - -
LZL05-L-M/P-NEMA mm 152 Ø165.1 Ø114.3 Ø15.875 17.85 4.75 51.5 31.75 1 3.175 10 M5x15 81 BSP ½” 44 Ø76 Ø149.225 ⅜”-16 UNC 0.5 -
LZL05-L-M/P-NEMA inch 5.98 Ø6.5 Ø4.5 Ø0.625 0.703 0.187 2.03 1.25 0.04 0.125 0.39 M5x15 3.19 BSP ½” 1.73 Ø3 Ø5.875 ⅜”-16 UNC 0.02 -
LZL05-L-P-HUB mm 152 Ø84 Ø44.45 j6 Ø12.7 14.51 3.175 H7 45 12.3 6.8 16 8.5 - 81 BSP ½” 44 Ø76 Ø63.6 ¼"-20 UNC 15.5 4.1
LZL05-L-P-HUB inch 5.98 Ø3.31 Ø1.75 Ø0.5 0.57 0.125 1.77 0.5 0.3 0.63 0.335 - 3.19 BSP ½” 1.73 Ø3 Ø2.5 ¼"-20 UNC 0.61 0.161
LZL05-RL-P-IEC mm 152 Ø160 Ø110 j6 Ø14 j7 16 5 h9 30 20 2.0 3.5 8.5 M5x15 81 BSP ½” 44 Ø76 Ø130 Ø10 - -
LZL05-RL-P-NEMA mm 152 Ø165.1 Ø114.3 Ø15.875 17.85 4.75 51.5 31.75 1 3.175 10 M5x15 81 BSP ½” 44 Ø76 Ø149.225 ⅜”-16 UNC 0.5 -
LZL05-RL-P-NEMA inch 5.98 Ø6.5 Ø4.5 Ø0.625 0.703 0.187 2.03 1.25 0.04 0.125 0.39 M5x15 3.19 BSP ½” 1.73 Ø3 Ø5.875 ⅜”-16 UNC 0.02 -
LZL15-L-P-AC mm 181.5 Ø140 Ø95 j6 Ø22 j7 24.5 6 h9 52.5 40 5.0 3.0 12 M6x16 95 BSP 3/4" 54 Ø100 Ø115 Ø9 - -
LZL15-L-P-IEC mm 181.5 Ø200 Ø130 j6 Ø19 j6 21.5 6 h9 40.5 30 5.0 3.5 12 M6x16 95 BSP 3/4" 54 Ø100 Ø165 Ø12 - -
LZL15-L-P-NEMA mm 181.5 Ø165.1 Ø114.3 Ø15.875 17.85 4.75 51.5 31.75 1.5 3.175 12 M6x16 95 BSP 3/4" 54 Ø100 Ø149.225 ⅜”-16 UNC - -
LZL15-L-P-NEMA inch 7.15 Ø6.5 Ø4.5 Ø0.625 0.703 0.187 2.03 1.25 0.06 0.125 0.472 M6x16 3.74 BSP 3/4" 2.13 Ø3.94 Ø5.875 ⅜”-16 UNC - -
LZL25-L-P-AC mm 221 Ø160 Ø110 j6 Ø28 j7 31 8 h7 62.5 50 5.0 3 12 M10x22 118 BSP 1” 70 Ø120 Ø130 Ø10 - -
LZL25-L-P-IEC mm 221 Ø200 Ø130 j6 Ø24 j6 27 8 h7 49.5 40 5.0 3.5 12 M10x22 118 BSP 1" 70 Ø120 Ø165 Ø12 - -
LZL35-L-P-AC mm 248.5 Ø200 Ø130 j6 Ø28 j7 31 8 h7 60 50 5.0 3.5 14 M10x22 129 BSP 1¼" 70 Ø134 Ø165 Ø12 - -
LZL35-L-P-IEC mm 248.5 Ø250 Ø180 j6 Ø28 j6 31 8 h7 60 50 5.0 4.0 14 M10x22 129 BSP 1¼" 70 Ø134 Ø215 Ø14.5 - -
2000 4000 6000 8000 r/min 2000 4000 6000 r/min 2000 4000 6000 r/min
LZL03-L-M
Throttled with air flow restrictor
Nm l/s
LZL: Performance curves at air pressure 6.3 bar (91 psi)
1.25 3.0 Curve idling speed
2.8 1400 rpm Torque 1400 rpm Air Cons.
Low to medium speed 1.0 2.6
2.4 1200 rpm Torque 1200 rpm Air Cons.
0.75 2.2
LZL03-L-M 2.0 1000 rpm Torque 1000 rpm Air Cons.
0.5 Throttled with air flow restrictor 1.8
800 rpm Torque 800 rpm Air Cons.
kW Nm LZL03-L-M l/s kW Nm LZL05-L-M / LZL05-RL-P l/s
Nm 1.6
l/s
4.0 2.0 7.5 0.25 1.4 600 rpm Torque
1.25 3.0 Curve idling speed 600 rpm Air Cons.
1.2
1.05 3.5 2.8 1400 rpm Torque 1400 rpm Air Cons.
1.0
1.6 6.0 401.0 200 400 600 800 10002.6 r/min
0.9 3.0
2.4 1200 rpm Torque 1200 rpm Air Cons.
0.75 2.5 25 1.2 4.5 30
0.75 2.2
0.6 2.0 20 2.0 1000 rpm Torque 1000 rpm Air Cons.
15 0.8 3.0 200.5 1.8
0.45 1.5 800 rpm Torque 800 rpm Air Cons.
1.6
0.3 1.0 10 0.25 1.4
0.4 1.5 10 600 rpm Torque 600 rpm Air Cons.
0.15 0.5 5 1.2
1.0
500 1000 1500 2000 2500 3000 r/min 500 1000 1500 2000 2500 3000 r/min 200 400 600 800 1000 r/min
LZL05-L-M
Throttled with air flow restrictor
l/s kW Nm LZL05-L-M / LZL05-RL-P l/s Nm l/s
2.0 7.5 1.75 4.0 Curve idling speed
1.5 3.5 1400 rpm Torque 1400 rpm Air Cons.
1.6 6.0 40
1.25
3.0 1200 rpm Torque 1200 rpm Air Cons.
25 1.2 4.5 30 1.0
20 LZL05-L-M 2.5 1000 rpm Torque 1000 rpm Air Cons.
0.8 3.0 20 0.75 Throttled with air flow restrictor
15
2.0 800 rpm Torque 800 rpm Air Cons.
0.5
Nm l/s
10
0.4 1.5 10 1.5
1.75
0.25 4.0 600
Curve rpm Torque
idling speed 600 rpm Air Cons.
5
1.5 1.0
3.5 1400 rpm Torque 1400 rpm Air Cons.
000 r/min 500 1000 1500 2000 2500 3000 r/min 200 400 600 800 1000 r/min
1.25
3.0 1200 rpm Torque 1200 rpm Air Cons.
1.0
2.5 1000 rpm Torque 1000 rpm Air Cons.
0.75
2.0 800 rpm Torque 800 rpm Air Cons.
0.5
Torque
Nm 0.25 1.5 600 rpm Torque 600 rpm Air Cons.
Power
kW Air cons. 1.0
Power l/s 200 400 600 800 1000 r/min
Max
output
Air. cons.
Conversion factors
1 kW = 1.34 hp
Torque
1 Nm = 0.74 Ibf - ft
Torque
at max
power 1 l/s = 2.1 cfm
1 hp
1 Ibf-ft
= 0.75 kW
= 1.36 Nm –––––
---------
Speed r/min Performance with restrictors
1 cfm = 0.47 l/s
For information about performance curves, see page 6. Performance without restrictors, (unrestricted)
Operating speed
The maximum allowable radial load on the output shaft of There are two options of mounting arrangement:
each gear unit, at the halfway point on the shaft can be Foot or Flange as illustrated in Figure 5.
obtained from the data tables for each model.
Figure 5
Temperature
B3 B5 B6 B51
B7 B53 B8 B52
V5 V1 V6 V3
NOTE: For some positions additional oil needs to be added to the gear box, see service instructions for details
1.2 – 2.0 kW
1.7 – 2.6 hp
Model Ratio kW hp r/min Nm lb-ft Nm lb-ft r/min r/min l/s cfm kg lb N Ordering No.
LZL05-BF322-A-012 12.3 1.2 1.7 352 33 25 56 41 740 36 77 14 31 2360 8411 1808 40
LZL05-BF322-B-012 12.3 1.2 1.7 352 33 25 56 41 740 36 77 14 31 2360 8411 1808 57
Unrestricted* 12.3 2.0 2.6 512 36 27 56 41 740 54 114 14 31 2100
LZL05-BF322-A-018 18.2 1.2 1.7 238 49 36 83 61 500 36 77 14 31 2770 8411 1808 65
LZL05-BF322-B-018 18.2 1.2 1.7 238 49 36 83 61 500 36 77 14 31 2770 8411 1808 73
Unrestricted* 18.2 2.0 2.6 346 54 40 83 61 500 54 114 14 31 2450
LZL05-BF322-A-033 33.1 1.2 1.7 131 90 66 151 111 275 36 77 14 31 3370 8411 1808 81
LZL05-BF322-B-033 33.1 1.2 1.7 131 90 66 151 111 275 36 77 14 31 3370 8411 1808 99
Unrestricted* 33.1 2.0 2.6 190 97 72 151 111 275 54 114 14 31 3000
LZL05-BF322-A-060 59.4 1.2 1.7 73 161 119 271 200 153 36 77 14 31 4800 8411 1809 07
LZL05-BF322-B-060 59.4 1.2 1.7 73 161 119 271 200 153 36 77 14 31 4800 8411 1810 15
Unrestricted* 59.4 2.0 2.6 106 174.9 129 271 200 153 54 114 14 31 4280
LZL05-BF363-A-102 102.2 1.2 1.6 42 272 200 456 336 89 36 77 22 49 5650 8411 1810 23
LZL05-BF363-B-102 102.2 1.2 1.6 42 272 200 456 336 89 36 77 22 49 5650 8411 1810 31
Unrestricted* 102.2 1.9 2.6 62 295 217 456 336 89 54 114 22 49 5020
LZL05-BF363-A-140 139.8 1.2 1.6 31 372 274 624 460 65 36 77 22 49 5690 8411 1810 49
LZL05-BF363-B-140 139.8 1.2 1.6 31 372 274 624 460 65 36 77 22 49 5690 8411 1810 56
Unrestricted* 139.8 1.9 2.6 45 403 297 624 460 65 54 114 22 49 5060
100 200 300 400 500 600 700 800 r/min 100 200 300 400 500 r/min 50 100 150 200 250 300 r/min
Torque
Nm
Power
kW Air cons.
Power l/s
Max
output
Air. cons.
Conversion factors
1 kW = 1.34 hp
Torque
1 Nm = 0.74 Ibf - ft
Torque
at max
power 1 l/s = 2.1 cfm
1 hp
1 Ibf-ft
= 0.75 kW
= 1.36 Nm –––––
---------
Speed r/min Performance with restrictors
1 cfm = 0.47 l/s
For information about performance curves, see page 6. Performance without restrictors, (unrestricted)
2.1 – 3.0 kW
2.9 – 4.1 hp
Model Ratio kW hp r/min Nm lb-ft Nm lb-ft r/min r/min l/s cfm kg lb N Ordering No.
LZL15-BF322-A-011 11.2 2.2 2.9 307 68 50 116 86 639 61 129 19 42 2530 8411 1810 61
LZL15BF322-B-011 11.2 2.2 2.9 307 68 50 116 86 639 61 129 19 42 2530 8411 1810 79
Unrestricted* 11.2 3.0 4.1 389 74 55 116 86 639 86 181 19 42 2310
LZL15-BF322-A-018 18.2 2.2 2.9 189 111 82 188 139 393 61 129 19 42 2970 8411 1810 87
LZL15-BF322-B-018 18.2 2.2 2.9 189 111 82 188 139 393 61 129 19 42 2970 8411 1810 95
Unrestricted* 18.2 3.0 4.1 239 121 89.3 188 139 393 86 181 19 42 2710
LZL15-BF322-A-033 33.1 2.2 2.9 104 202 149 343 253 216 61 129 19 42 3600 8411 1811 03
LZL15-BF322-B-033 33.1 2.2 2.9 104 202 149 343 253 216 61 129 19 42 3600 8411 1811 11
Unrestricted* 33.1 3.0 4.1 132 220 162 343 253 216 86 181 19 42 3300
LZL15-BF322-A-060 59.4 2.2 2.9 58 362 267 615 454 120 61 129 19 42 5150 8411 1811 29
LZL15-BF322-B-060 59.4 2.2 2.9 58 362 267 615 454 120 61 129 19 42 5150 8411 1811 37
Unrestricted* 59.4 3.0 4.1 73 395 291 615 454 120 86 181 19 42 4710
LZL15-BF363-A-102 102.2 2.1 2.9 34 609 449 1036 764 70 61 129 27 60 6040 8411 1811 45
LZL15-BF363-B-102 102.2 2.1 2.9 34 609 449 1036 764 70 61 129 27 60 6040 8411 1811 52
Unrestricted* 102.2 3.0 4.0 43 665 491 1036 764 70 86 181 27 60 5520
LZL15-BF613-A-165 164.5 2.1 2.9 21 981 723 1668 1230 43 61 129 70 154 15000 8411 1811 60
LZL15-BF613-B-165 164.5 2.1 2.9 21 981 723 1668 1230 43 61 129 70 154 15000 8411 1811 78
Unrestricted* 164.5 3.0 4.0 26 1071 790 1668 1230 43 86 181 70 154 15000
*) Unrestricted, the motors should not be run without load
100 200 300 400 500 600 700 r/min 50 100 150 200 250 300 350 400 r/min 40 80 120 160 200 240 r/min
Torque
Nm
Power
kW Air cons.
Power l/s
Max
output
Air. cons.
Conversion factors
1 kW = 1.34 hp
Torque
1 Nm = 0.74 Ibf - ft
Torque
at max
power 1 l/s = 2.1 cfm
1 hp
1 Ibf-ft
= 0.75 kW
= 1.36 Nm –––––
---------
Speed r/min Performance with restrictors
1 cfm = 0.47 l/s
For information about performance curves, see page 6. Performance without restrictors, (unrestricted)
3.3 – 4.8 kW
4.4 – 6.4 hp
Model Ratio kW hp r/min Nm lb-ft Nm lb-ft r/min r/min l/s cfm kg lb N Ordering No.
LZL25-BF322-A-011 11.2 3.3 4.4 254 123 91 192 141 531 86 183 26 57 2700 8411 1811 86
LZL25-BF322-B-011 11.2 3.3 4.4 254 123 91 192 141 531 86 183 26 57 2700 8411 1811 94
Unrestricted* 11.2 4.8 6.4 370 128 94 192 141 531 140 297 26 57 2430
LZL25-BF322-A-018 18.2 3.3 4.4 156 201 148 311 230 327 86 183 26 57 3170 8411 1812 02
LZL25-BF322-B-018 18.2 3.3 4.4 156 201 148 311 230 327 86 183 26 57 3170 8411 1812 10
Unrestricted* 18.2 4.8 6.4 227 207 153 311 230 327 140 297 26 57 2860
LZL25-BF363-A-035 34.6 3.2 4.3 82 373 275 579 427 172 86 183 34 75 4100 8411 1812 28
LZL25-BF363-B-035 34.6 3.2 4.3 82 373 275 579 427 172 86 183 34 75 4100 8411 1812 36
Unrestricted* 34.6 4.7 6.2 120 386 285 579 427 172 140 297 34 75 3700
L25-BF613-A-059 58.6 3.2 4.3 48 632 466 981 724 101 86 183 77 170 13000 8411 1812 44
LZL25-BF613-B-059 58.6 3.2 4.3 48 632 466 981 724 101 86 183 77 170 13000 8411 1812 51
Unrestricted* 58.6 4.7 6.2 71 654 482 981 724 101 140 297 77 170 11700
LZL25-BF613-A-114 113.6 3.2 4.3 25 1226 904 1902 1403 52 86 183 77 170 16000 8411 1812 69
LZL25-BF613-B-114 113.6 3.2 4.3 25 1226 904 1902 1403 52 86 183 77 170 16000 8411 1812 77
Unrestricted* 113.6 4.7 6.2 36 1268 935 1902 1403 52 140 297 77 170 16000
LZL25-BF613-A-165 164.5 3.2 4.3 17 1775 1309 2754 2031 36 86 183 77 170 16000 8411 1812 85
LZL25-BF613-B-165 164.5 3.2 4.3 17 1775 1309 2754 2031 36 86 183 77 170 16000 8411 1812 94
Unrestricted* 164.5 4.7 6.2 25 1836 1354 2754 2031 36 140 297 77 170 16000
1 50 50 1 100 50 1 150 50
100 200 300 400 500 600 r/min 50 100 150 200 250 300 350 r/min 40 80 120 160 200 r/min
Torque
Nm
Power
kW Air cons.
Power l/s
Max
output
Air. cons.
Conversion factors
1 kW = 1.34 hp
Torque
1 Nm = 0.74 Ibf - ft
Torque
at max
power 1 l/s = 2.1 cfm
1 hp
1 Ibf-ft
= 0.75 kW
= 1.36 Nm –––––
---------
Speed r/min Performance with restrictors
1 cfm = 0.47 l/s
For information about performance curves, see page 6. Performance without restrictors, (unrestricted)
5.1 – 6.3 kW
6.8 – 8.4 hp
Model Ratio kW hp r/min Nm lb-ft Nm lb-ft r/min r/min l/s cfm kg lb N Ordering No.
LZL35-BF322-A-006 6.3 5.0 6.7 394 121 90 192 141 838 129 273 34 75 2360 8411 1813 01
LZL35-BF322-B-006 6.3 5.0 6.7 394 121 90 192 141 838 129 273 34 75 2360 8411 1813 19
Unrestricted* 6.3 6.2 8.3 464 128 94 192 141 838 159 337 34 75 2230
LZL35-BF322-A-011 11.2 5.0 6.7 221 216 159 340 251 471 129 273 34 75 2810 8411 1813 27
LZL35-BF322-B-011 11.2 5.0 6.7 221 216 159 340 251 471 129 273 34 75 2810 8411 1813 35
Unrestricted* 11.2 6.2 8.3 261 227 167 340 251 471 159 337 34 75 2650
LZL35-BF613-A-029 29.4 4.9 6.6 84 555 409 875 645 180 129 273 85 187 10600 8411 1813 43
LZL35-BF613-B-029 29.4 4.9 6.6 84 555 409 875 645 180 129 273 85 187 10600 8411 1813 50
Unrestricted* 29.4 6.1 8.1 99 583 430 875 645 180 159 337 85 187 10000
LZL35-BF613-A-048 47.6 4.9 6.6 52 899 663 1417 1045 111 129 273 85 187 12100 8411 1813 68
LZL35-BF613-B-048 47.6 4.9 6.6 52 899 663 1417 1045 111 129 273 85 187 12100 8411 1813 78
Unrestricted* 47.6 6.1 8.1 61 944 696 1417 1045 111 159 337 85 187 11400
*) Unrestricted, the motors should not be run without load
200 400 600 800 1000 r/min 100 200 300 400 500 r/min 40 80 120 160 200 r/min
kW Nm LZL35-BF613-A/B-048 l/s
7
6 1800 240
5 1500 200
4 1200 160
3 900 120
2 600 80
1 300 40
Torque
Nm
Power
kW Air cons.
Power l/s
Max
output
Air. cons.
Conversion factors
1 kW = 1.34 hp
Torque
1 Nm = 0.74 Ibf - ft
Torque
at max
power 1 l/s = 2.1 cfm
1 hp
1 Ibf-ft
= 0.75 kW
= 1.36 Nm –––––
---------
Speed r/min Performance with restrictors
1 cfm = 0.47 l/s
For information about performance curves, see page 6. Performance without restrictors, (unrestricted)
M
P
G O ØS
H
B
F
R
ØQ
A
D
N
ØC
E
X
I K ØT
J U
L V
ØM
ØQ
ØD
ØE
A
LZL35-BF613-A-xxx 53.5 14 h9 50 h6 316 195 5.0 100 90 125 180 N/A 232 692.5 M16x36 BSP 1 1/4 119.5 Ø134 68 Ø250 Ø18 250 300 25
R
N
ØQ
ØC
A
D
N
ØC
E
X
L
I
I K ØT ØT
J
J U
Flange models L V
G P
H O ØS
B F
R
ØM
ØQ
ØD
ØE
A
ØC
L
I
ØT
J
Temperatures
TZB25 is built on turbine technology and is 40% more efficient than a traditional type of air motor using vane technology.
Available in clockwise and counter clockwise direction. The 2.8 Kw – 3.8 hp TZB is geared for high torque applications and
capable of maintaining stable speed under load. The TZB has a compact design with two mounting options for easy installation
as standard. Designed and built for tough applications, the TZB outlasts and outperforms. A turbine motor that brings innovation
and efficiency in tough applications.
Lube free
Air Air
Speed Torque Min consumption consump-
Max at max at max starting Stall Free at max tion
Shaft
Output output output torque torque speed output at Idling weight
load-
lb- lb- lb- ing
Model Kw hp rpm Nm ft Nm ft Nm ft rpm l/s cfm l/s cfm kg lb code ATEX code Ordering No
TZB25-L-A0008-14 2.7 3.6 70 370 270 680 500 700 510 80 40 85 10 20 5.3 11.7 h EX II 2 GD h T4 IIh T135oC X 8411 3100 16
TZB25-L-A0012-14 2.7 3.6 110 230 170 440 325 460 340 120 40 85 10 20 5.3 11.7 h EX II 2 GD h T4 IIh T135oC X 8411 3100 24
TZB25-L-A0032-14 2.8 3.8 280 95 70 165 120 170 125 320 40 85 10 20 3.5 7.7 d EX II 2 GD h T4 IIh T135oC X 8411 3100 32
TZB25-L-A0050-14 2.8 3.8 450 60 45 110 80 110 80 500 40 85 10 20 3.5 7.7 d EX II 2 GD h T4 IIh T135oC X 8411 3100 40
TZB25-L-AV0008-14 2.7 3.6 70 380 280 680 500 705 520 80 40 85 10 20 5.3 11.7 h EX II 2 GD h T4 IIh T135oC X 8411 3100 57
TZB25-L-AV0012-14 2.7 3.6 100 270 200 470 345 490 360 115 40 85 10 20 5.3 11.7 h EX II 2 GD h T4 IIh T135oC X 8411 3100 65
TZB25-L-AV0032-14 2.8 3.8 280 100 75 165 120 170 125 320 40 85 10 20 3.5 7.7 d EX II 2 GD h T4 IIh T135oC X 8411 3100 73
TZB25-L-AV0053-14 2.8 3.8 470 60 45 100 75 105 75 530 40 85 10 20 3.5 7.7 d EX II 2 GD h T4 IIh T135oC X 8411 3100 81
Dimensions in mm
M5
depth 15
Thread
370
55.6 164
10.4
Ø19.05 h6
Ø68.3
Ø80
88
Ø20
108
depth 15
M5
Thread
262
55.6 112.5
12
10.4
Ø19.05 h6
Ø68.3
88
Ø20
10 10 30 10
0.5 100 0.5 100 0.5
20 40 60 80 100 rpm 20 40 60 80 100 rpm 50 100 150 200 250 300 350 rpm
20 10 10 100 10
0.5 0.5 100 0.5
100 200 300 400 500 600 rpm 20 40 60 80 100 rpm 20 40 60 80 100 120 140 rpm
2.5 2.5
120 40 80 40
2.0 2.0
90 30 60 30
1.5 1.5
60 20 40 20
1.0 1.0
30 10 20 10
0.5 0.5
50 100 150 200 250 300 350 rpm 100 200 300 400 500 600 rpm
Air Air
Speed Torque Min consumption consump-
Max at max at max starting Stall Free at max tion
Shaft
Output output output torque torque speed output at Idling weight
load-
lb- lb- lb- ing
Model Kw hp rpm Nm ft Nm ft Nm ft rpm l/s cfm l/s cfm kg lb code ATEX code Ordering No
TZB25-L-A0008-15 2.7 3.6 70 370 270 680 500 700 510 80 40 85 10 20 5.6 12.3 h EX II 2 GD h T4 IIh T135oC X 8411 3100 17
TZB25-L-A0012-15 2.7 3.6 110 230 170 440 325 460 340 120 40 85 10 20 5.6 12.3 h EX II 2 GD h T4 IIh T135oC X 8411 3100 25
TZB25-L-A0032-15 2.8 3.8 280 95 70 165 120 170 125 320 40 85 10 20 3.8 8.4 d EX II 2 GD h T4 IIh T135oC X 8411 3100 33
TZB25-L-A0050-15 2.8 3.8 450 60 45 110 80 110 80 500 40 85 10 20 3.8 8.4 d EX II 2 GD h T4 IIh T135oC X 8411 3100 41
TZB25-L-AV0008-15 2.7 3.6 70 380 280 680 500 705 520 80 40 85 10 20 5.6 12.3 h EX II 2 GD h T4 IIh T135oC X 8411 3100 58
TZB25-L-AV0012-15 2.7 3.6 100 270 200 470 345 490 360 115 40 85 10 20 5.6 12.3 h EX II 2 GD h T4 IIh T135oC X 8411 3100 66
TZB25-L-AV0032-15 2.8 3.8 280 100 75 165 120 170 125 320 40 85 10 20 3.8 8.4 d EX II 2 GD h T4 IIh T135oC X 8411 3100 74
TZB25-L-AV0053-15 2.8 3.8 470 60 45 100 75 105 75 530 40 85 10 20 3.8 8.4 d EX II 2 GD h T4 IIh T135oC X 8411 3100 82
Dimensions in mm
depth 16
M6
Thread
364
62.5 152
12
Ø25.4 j6
Ø89
34.9
109
depth 16
M6
Thread
306
57 100
12
Ø25.4 j6
Ø89
88
PZB piston motors are available in tree sizes, offering outputs from 0.04 (0.05 hp) to 0.2 (0.27hp).
The PZB range of piston air motors is energy efficient and has unique low speed and high starting torque features, adding value
in many applications. The compact design and flange configurations make it easy to install. The PZB air motor is ATEX Certified
and operates without lubrication, making it ideal for white room and chemical, as well as automation and handling applications.
1.Flange configuration
2. Centrifugal piston technology.
3 3. Long life bearings
* Motor without restrictor plates in the air in- and outlet, the motors should not be run above max allowed speed.
PZB 09-21 : Performance curves at air pressure 6.3 bar (91 psi) and Shaft load curves
kW Nm PZB09-L-AR500-11 l/s kW Nm PZB15-L-AR500-11 l/s kW Nm PZB21-L-300-11 l/s
0.10 5 0.14 18
0.24
0.12 9.0 15
0.08 4 7.5 0.20 15
4 0.10 7.5
0.16 12 12
0.06 3 6.0
3 0.08 6.0
0.12 9 9
0.06 4.5 4.5
0.04 2 2
3.0 0.08 6 6
0.04 3.0
0.02 1 1 0.02 1.5 1.5 0.04 3 3
0 100 200 300 400 500 rpm 0 100 200 300 400 500 rpm 0 50 100 150 200 250 300 rpm
3000 3000
2500 2500
2000 2000
Fr[N]
Fr[N]
1500 1500
1000 1000
500 500
0 0
0 200 400 600 800 1000 1200 1400 1600 0 200 400 600 800 1000 1200 1400 1600 1800 2000
Fa[N] Fa[N]
a c ba dc
Torque
Nm
Power
kW Air cons.
Power l/s
Max
output
Air. cons.
Conversion factors
1 kW = 1.34 hp
Torque
1 Nm = 0.74 Ibf - ft
Torque
at max
power 1 l/s = 2.1 cfm
1 hp = 0.75 kW
1 Ibf-ft = 1.36 Nm
Speed r/min
Atlas1 cfm
Copco Air Motors
= 0.47 l/s | 105
For information about performance curves, see page 6.
Dimensions (mm)
L3
L2
L1
L6 L5
D4
A
L4
D2
D1
M
D5
D3
67.50
D6
PZB09 – AC99 Ø99 Ø14 Ø99 Ø55 Ø67 Ø12 M4x9 M6x10 M5x6 25 27 81.5 15.75 5 16 M4x10 8411 4090 00
PZB09 – IEC-FF115 Ø99 Ø14 Ø140 Ø95 Ø115 Ø12 Ø10 M6x10 M5x6 25 24 81.5 15.75 5 16 M4x10 8411 4090 18
PZB09 – NEMA-56C Ø99 Ø5/8” Ø6.5” Ø4.5” Ø5.875” Ø12 3/8”-16 M6x10 M5x6 50 2.06” 107.5 17.85 3/16” 1 ¼” - 8411 4090 26
PZB09 – AC-BF99 Ø99 Ø14 Ø99 Ø55 Ø67 Ø12 M4x9 M6x10 M5x6 25 27 111.5 15.75 5 16 M4x10 8411 4090 34
PZB09 – AC129 Ø99 Ø19 Ø129 Ø95 Ø115 Ø12 M6 & Ø6,7 M6X10 M5X6 40 43.5 98 21.75 6 28 M6x18 8411 4090 67
PZB15 – AC99 Ø99 Ø14 Ø99 Ø55 Ø67 Ø12 M4x9 M6x10 M5x6 25 27 96.5 15.75 5 16 M4x10 8411 4150 00
PZB15 – IEC-FF115 Ø99 Ø14 Ø140 Ø95 Ø115 Ø12 Ø10 M6x10 M5x6 25 24 96.5 15.75 5 16 M4x10 8411 4150 18
PZB15 – NEMA-56C Ø99 Ø5/8” Ø6.5” Ø4.5” Ø5.875” Ø12 3/8”-16 M6x10 M5x6 50 2.06” 122.5 17.85 3/16” 1 ¼” - 8411 4150 26
PZB15 – AC129 Ø99 Ø19 Ø129 Ø95 Ø115 Ø12 M6 & Ø6,7 M6X10 M5X6 40 43.5 113 21.75 6 28 M6x18 8411 4150 67
PZB21 – AC159 Ø159 Ø19 Ø159 Ø95 Ø115 Ø16 M6x10 G1/8”x10 M5x6 40 43 113.5 21.75 6 28 M6x18 8411 4210 00
PZB21 – IEC-FF115 Ø159 Ø19 Ø240 Ø180 Ø215 Ø16 Ø14,5 G1/8”x10 M5x6 40 39 113.5 21.75 6 28 M6x18 8411 4210 18
PZB21 – NEMA-56C Ø159 Ø5/8” Ø6.5” Ø4.5” Ø5.875” Ø16 3/8”-16x10 G1/8”x10 M5x6 50 2.06” 125 17.85 3/16” 1 ¼” - 8411 4210 26
PZB21 – AC-BF159 Ø159 Ø19 Ø159 Ø95 Ø115 Ø16 M6x10 G1/8”x10 M5x6 40 43 162.5 21.75 6 28 M6x18 8411 4210 34
ATEX certificate:
Atlas Copco AB
(publ) SE-105 23 Stockholm, Sweden
Phone: +46 8 743 80 00
Reg. no: 556014-2720
atlascopco.com