KBE_MOT-€DC17SCR-Bosch_B977_KO001 Version: 1.0 Page: 116
[os-68)
B377 FUEL PRESSURE SENSOR
COMPONENT DESCRIPTION
Table of contents
41, Fuel pressure sensor.
4.1, Installation location...
1,2, Pin assignment...
1.3. Measured values.
2, Test recommendation.n.nniisnnnn
2.1. Check the power supply of the fuel pressure sensor.
2.2. Checking the cable harness for disconnection.
2.3, Checking the cable hamess for short ciCuit....n
2.4, Checking the cable hamess for short circuit to ground.
2.5. Checking the voltage signal of the fuel pressure sensor.
3. MAN-cats®,
1. Fuel pressure sensor
The fuel pressure sensor monitors the fuel
pressure at the pump feed (low-pressure
side). By changing the fuel pressure the
output signal voltage changes.
1.1, Installation locationVersion: 1.0 Page: 216 [o-68)
kee_MoT-eD¢?
{CR-Bosch_B977_O001
The fuel pressure sensor is mounted on the
fuel filter system (KSC) (illustration shows
an example).
Key
Number Designation
Fuel pressure sensor
1.2. Pin assignment
Key
Number Designation
Power supply
Ground
Signal voltage
1.3. Measured valueskee_MoT-eDc?
{CR-Bosch_8977_Ko! Version: 1.0 Page: 316 [oo-68)
Technical data
Designation Setpoint values
Power supply 5v
Pressure measuring range From 0 bar (0.5 V) to 15 bar (4.5 V)
2. Test recommendation
Co
If this instruction is not followed, it could result in damage to the component or to other
objects.
Therefore:
+ Always use the latest MAN-cats® version
Use a digital multimeter.
Use test device EDC17/EGC4, item number 80.99641-6070
Use test adapter, item number 80.99641-6044
2.1. Check the power supply of the fuel pressure sensor
Measure the voltage between the required contacts as per the following table:
Designation Contact Setpoint values
Fuel pressure sensor 1 4.75-5.25V
Ground Terminal 31
2.2. Checking the cable harness for disconnectionKBE_MOT-EDC17SCR-Bosch_ 83% Version: 1.0 Page: 46 [oo-68)
Measure the resistance between the required contacts as per the following table:
Designation Contact Setpoint values
Fuel pressure sensor 1 0029
‘A435 EDC control unit cet
Fuel pressure sensor 2 00.20
A435 EDC control unit c19
Fuel pressure sensor 3 0020
A435 EDC control unit C35,
2.3. Checking the cable harness for short circuit
Measure the resistance between the required contacts as per the following tab|
Designation Contact Setpoint values
Fuel pressure sensor 1 >1MQ
Fuel pressure sensor 2
Fuel pressure sensor 1 >1Ma
Fuel pressure sensor 3
Fuel pressure sensor 2 >1MaKBE_MOT-EDCH7SCR och BS Version: 1.0 Page: 518 (er-60
Designation Contact Setpoint values
Fuel pressure sensor 3
2.4, Checking the cable harness for short circuit to ground
Measure the resistance between the required contacts as per the following table:
Designation Contact Setpoint values
Fuel pressure sensor 1 >1MO
Ground Terminal 31
Fuel pressure sensor 2 >1MQ
Ground Terminal 31
Fuel pressure sensor 3 >1MO
Ground Terminal 31
2.5. Checking the voltage signal of the fuel pressure sensor
Measure the voltage signal as per the following table: Use the EDC17/EGC4 testing rig for
the measuring process and allow the engine to idle for at least one minute.
Designation Contact Setpoint values
A435 EDC control unit C35 1-2.5V01 Version: 1.0
Page: 616
[oo-68)
Designation Contact
A435 EDC control unit c19
3. MAN-cats®
*MOT-EDC17SCR-Bosch-Monitoring Pressures*
Setpoint values