Professional Documents
Culture Documents
What Is Rogers CuClad 233 PCB
What Is Rogers CuClad 233 PCB
Table of Contents
The Rogers CuClad 233 laminate utilizes a medium PTFE/fiberglass ratio which
balances off the lower Dk. Due to this feature, the Rogers CuClad 233 laminate can
boost its dissipation factor with no effect on the mechanical properties. In addition,
the laminate is also reinforced using woven glass, which in turn increases the
laminate’s dimensional stability. These two features make the Rogers CuClad 233 an
excellent choice for low-noise amplifiers, couplers, and filters.
The Rogers CuClad 233 laminate has a construction that is cross plied. Due to this
construction, the laminate can maintain impeccable dimensional stability. It can also
balance mechanical and electrical properties, which in turn boost its efficiency
immensely.
The Rogers CuClad 233 laminate bears the following features that make it stand out
when you compare it with other laminates:
If you are looking to utilize the Rogers CuClad 233 laminate, here are some benefits
that you are going to get:
laminate
The Rogers CuClad 233 laminate features the following properties. Each one curves
the laminate into one of the best laminates in the world today.
Physical properties
Physical properties are the properties that we can observe and measure without
affecting a component’s chemical composition.
The Rogers CuClad 233 laminate bears the following physical properties:
Density
2.26 g/cc
Water Absorption
Water absorption is one feature that stands out in the Rogers CuClad 233 laminate.
The laminate bears a pretty low water absorption rate that hits:
The Rogers CuClad 233 laminate has an outgassing value of 0.00% (and 0.010 via
NASA) under the following conditions:
The laminate has 0.010% volatile condensable components under the following test
conditions:
laminate
When you apply a force upon a Rogers CuClad 233 laminate, it is bound to exhibit
the following mechanical properties:
Tensile strength
Under normal conditions, the Rogers CuClad 233 laminate has a tensile strength of:
67.6 MPa
Modulus of elasticity
The Rogers CuClad 233 laminate has the following modulus of elasticity:
2.85 GPA
Flexure modulus
The flexure modulus of the Rogers CuClad 233 laminate under a temperature of 230C
is:
>=2.56 GPA
Compressive modulus
1.90 GPA
Peel strength
After applying thermal stress to the Rogers CuClad 233 laminate, its peel strength hits
a whooping:
2.45 kN/m
The Rogers CuClad 233 laminate features the following electrical properties:
Volume resistivity
Under normal conditions, the Rogers CuClad 233 laminate bears the following
volume resistivity:
8.00e + 14 ohms- cm
Surface resistance
2.40e + 12 ohm
The Rogers CuClad 233 laminate has a dielectric constant of 2.33 under the following
test conditions:
A frequency of 1.00e + 6 Hz
When you up the frequency to 1.00e + 10 Hz, the Dk of the Rogers CuClad 233
laminate remains stagnant at:
2.33
Dielectric Breakdown
The Rogers CuClad 233 laminate has the following dielectric breakdown:
>= 45000V
Dissipation factor
The Rogers CuClad 233 laminate has a dissipation factor of 0.0013 under the
following conditions:
Arc resistance
The Rogers CuClad 233 laminate has an arc resistance that is:
Thermal properties are a significant factor to consider as PCBs are almost always
under constant heat. Hence having a laminate with impeccable thermal properties is
essential.
The Rogers CuClad 233 laminate has the following thermal properties:
CTE linear
The Rogers CuClad 233 laminate has an X CTE linear of 23.0 µm/m-°C under the
following conditions:
Under the same test conditions, the y-direction CTE linear value hits 24.0 µm/m-°C
under the same test conditions.
Thermal conductivity
The Rogers CuClad 233 laminate has the following thermal conductivity:
0.258 W/m-K
Flammability
V-0
Conclusion
The Rogers CuClad 233 laminate is a durable, efficient and effective laminate. Its
feature and benefits make it one of a kind in the tech market. Hence if you are looking
for a laminate to utilize on your PCB, look no further.
Related Posts:
https://www.raypcb.com/rogers-cuclad-233-pcb/