Professional Documents
Culture Documents
LOCTITE® 262™
December-2009
l
ee
St
Viscosity Medium, thixotropic 75
Cure Anaerobic Zinc dichromate
Secondary Cure Activator
Application Threadlocking 50
Strength Medium to High Brass
® 25 el
LOCTITE 262™ is designed for the permanent locking and s ste
sealing of threaded fasteners. The product cures when in les
Sta
confined in the absence of air between close fitting metal 0
surfaces and prevents loosening and leakage from shock and 1min 5min10min 30min 1h 3h 6h 24h 72h
Cure Time
vibration. Typical applications include the locking and sealing
of large bolts and studs (up to M25 ). The thixotropic nature of Cure Speed vs. Bond Gap
LOCTITE® 262™ reduces the migration of liquid product after The rate of cure will depend on the bondline gap. Gaps in
application to the substrate. threaded fasteners depends on thread type, quality and size.
The following graph shows shear strength developed with time
Mil-S-46163A on steel pins and collars at different controlled gaps and tested
LOCTITE® 262™ is tested to the lot requirements of Military according to ISO 10123.
Specification Mil-S-46163A. Note: This is a regional approval. 100
% of Full Strength on Steel
m
ASTM D5363
5m
m
5m
m
Each lot of adhesive produced in North America is tested to
0.0
2
0.1
0.
the general requirements defined in paragraphs 5.1.1 and 50
5.1.2 and to the Detail Requirements defined in section 5.2.
NSF International 25
Registered to NSF Category P1 for use as a sealant where
there is no possibility of food contact in and around food
processing areas. Note: This is a regional approval. Please 0
contact your local Technical Service Center for more 1min 5min10min 30min 1h 3h 6h 24h 72h
information and clarification. Cure Time
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
TDS LOCTITE® 262™, December-2009
% of Full Strength on Steel 100 M10 steel nuts and bolts N·m 40
(lb.in) (350)
C°
(psi) (≥1,450)
22
50
°C
After 1 hour @ 22 °C
5 °C
40
25 Compressive Shear Strength, ISO 10123:
Steel pins and collars N/mm² ≥3
(psi) (≥435)
0
1min 5min10min 30min 1h 3h 6h 24h 72h
Cure Time
75 Heat Aging
Aged at temperature indicated and tested @ 22 °C
No activator
125
49
50
76
% Strength @ 22 °C
100
71
74
25
75
120 °C
0 50
1min 5min10min 30min 1h 3h 6h 24h 72h
Cure Time 150 °C
25
TYPICAL PROPERTIES OF CURED MATERIAL
Physical Properties: 0
Coefficient of Thermal Expansion, 80×10-6 0 1000 2000 3000 4000 5000
ISO 11359-2, K-1 Exposure Time, hours
Coefficient of Thermal Conductivity, ISO 8302, 0.1
W/(m·K)
Chemical/Solvent Resistance
Specific Heat, kJ/(kg·K) 0.3
Aged under conditions indicated and tested @ 23 °C.
% of initial strength
TYPICAL PERFORMANCE OF CURED MATERIAL Environment °C 100 h 500 h 1000 h 5000 h
Adhesive Properties Motor oil (MIL-L-46152) 125 85 85 75 75
After 24 hours @ 22 °C Leaded Petrol 22 100 100 100 100
Breakaway Torque, ISO 10964: Brake fluid 22 100 100 100 100
M10 steel nuts and bolts N·m 22 Water/glycol 50/50 87 100 85 85 85
(lb.in) (190)
Acetone 22 95 95 95 95
Prevail Torque, ISO 10964: Ethanol 22 95 95 95 95
M10 steel nuts and bolts N·m 32 ® 22 128 140 125
DEF (AdBlue )
(lb.in) (280)
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
TDS LOCTITE® 262™, December-2009
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
TDS LOCTITE® 262™, December-2009
The data contained herein are furnished for information only and are
believed to be reliable. We cannot assume responsibility for the results
obtained by others over whose methods we have no control. It is the
user's responsibility to determine suitability for the user's purpose of
any production methods mentioned herein and to adopt such
precautions as may be advisable for the protection of property and of
persons against any hazards that may be involved in the handling and
use thereof. In light of the foregoing, Henkel Corporation specifically
disclaims all warranties expressed or implied, including
warranties of merchantability or fitness for a particular purpose,
arising from sale or use of Henkel Corporation’s products. Henkel
Corporation specifically disclaims any liability for consequential
or incidental damages of any kind, including lost profits. The
discussion herein of various processes or compositions is not to be
interpreted as representation that they are free from domination of
patents owned by others or as a license under any Henkel Corporation
patents that may cover such processes or compositions. We
recommend that each prospective user test his proposed application
before repetitive use, using this data as a guide. This product may be
covered by one or more United States or foreign patents or patent
applications.
Trademark usage
Except as otherwise noted, all trademarks in this document are
trademarks of Henkel Corporation in the U.S. and elsewhere. ®
denotes a trademark registered in the U.S. Patent and Trademark
Office.
Reference 0.7
For the most direct access to local sales and technical support visit: www.henkel.com/industrial