Professional Documents
Culture Documents
Nguon
Nguon
id091400110400
Note
• Terminals with terminal voltage that cannot be measured are not indicated in the terminal voltage table
(reference).
am2zzw00008324
Ter
mi Signal name Connected to Measurement conditions Voltage (V) Inspection item(s)
nal
Under any condition • ROOM 25A fuse
INTERIOR 15A • INTERIOR 15A fuse
1A Power supply B+ • Battery
fuse
• DC-DC converter*8
Ignition switched ON (engine off • C/U IG1 15 A fuse
B+
1B Power supply C/U IG1 15 A fuse or on) • Battery
Ignition switched off or at ACC 1.0 or less • DC-DC converter*8
Brake pedal depressed B+
1C Brake switch Brake switch Brake switch
Brake pedal not depressed 1.0 or less
Ignition Clutch pedal not • Starter relay
B+
switched depressed • Battery
ON • DC-DC converter*8
Starter monitor (MTX) Starter relay (engine Clutch pedal
1.0 or less • PCM
off or on) depressed • Starter Interlock
1D Switch
Ignition Other than selector • Starter relay
switched lever is in P or N B+ • Battery
Starter monitor (ATX) Starter relay ON position • DC-DC converter*8
(engine Selector lever is in P
off or on) 1.0 or less • PCM
or N position • TCM
Ter
mi Signal name Connected to Measurement conditions Voltage (V) Inspection item(s)
nal
Switch the ignition to ACC or ON • Outlet cigarette
B+
(engine off) socket
1E ACC monitor MIRROR 7.5 A fuse Ignition switched off • MIRROR 7.5 A fuse
1.0 or less • DC-DC converter*8
• ACC relay
Starter interlock switch Starter interlock Clutch pedal not depressed B+ Starter interlock
(MTX) switch Clutch pedal depressed 1.0 or less switch
Other than selector lever is in P
1F B+
Selector lever position switch or N position
TCM TCM
(ATX) Selector lever is in P or N
1.0 or less
position
Hazard warning switch not
B+
Hazard warning pressed (OFF) Hazard warning
1G Hazard warning switch signal
switch Hazard warning switch pressed switch
1.0 or less
(ON)
Push button start pressed 1.0 or less
1H Push button start 1 Push button start Push button start
Push button start not pressed B+
Integrity determination using terminal voltage
1I Push button illumination Push button start Push button start
inspection is not possible.
1J* P position Not P position Selector lever is in P position B+
Not P position switch
1 switch Except above 1.0 or less
Engine starting conditions are
Push button illumination 1.0 or less
1K Push button start met Push button start
(green)
Except above B+
Steering shift switch (up)
1.0 or less
1L* Steering shift switch (up) Steering shift switch
pressed
Steering shift switch
5 Steering shift switch (up) not
B+
pressed
Ignition switched to ACC or ON
Push button illumination 1.0 or less
1M Push button start (engine off) Push button start
(amber)
Except above B+
Steering shift switch (down)
1.0 or less
1N* Steering shift switch (down) Steering shift switch
pressed
Steering shift switch
5 Steering shift switch (down) not
B+
pressed
Door lock-link Driver's door locked 1.0 or less
Door lock-link switch
1P Lock input switch (driver's Driver's door unlocked
Approx. 5 (driver's door)
door)
Because this terminal is for communication, integrity determination
1Q BCM BCM
using terminal voltage inspection is not possible.
The specified time has elapsed
1S* Steering angle sensor power Steering angle since key placed outside vehicle 1.0 or less
Steering angle sensor
6 supply sensor and all doors locked
Except above Approx. 5
1T* Steering angle sensor Steering angle Under any condition
1.0 or less Steering angle sensor
6 ground sensor
Steering wheel is turned to left 4.00—
1U* Steering angle sensor (signal Steering angle
and right 4.75⇔0.25 Steering angle sensor
6 A/D1) sensor
—0.75
Steering wheel is turned to left 4.00—
1W Steering angle sensor (signal Steering angle
and right 4.75⇔0.25 Steering angle sensor
*6 A/D1) sensor
—0.75
RESUME switch is pressed Approx. 1.5
CANCEL switch is pressed 1.0 or less
ON switch is pressed Approx. 1.9
Cruise control
1Y Cruise control switch signal OFF switch is pressed Cruise control switch
switch
SET (+) switch is pressed 1.0 or less
SET (-) switch is pressed
Except above Approx. 3.6
Ter
mi Signal name Connected to Measurement conditions Voltage (V) Inspection item(s)
nal
Cruise control Under any condition
1Z Cruise control switch ground 1.0 or less Cruise control switch
switch
Up switch is pressed 1.0 or less
1A Down switch is pressed Approx. 1.2
Steering switch signal Steering switch Steering switch
A INFO button is pressed Approx. 2.2
Except above Approx. 3.3
1A Under any condition
Steering switch ground Steering switch 1.0 or less Steering switch
B
1A Coil antenna (push Because this terminal is for communication, integrity determination
PATS+
C button start) using terminal voltage inspection is not possible.
1A Coil antenna (push Because this terminal is for communication, integrity determination
PATS-
E button start) using terminal voltage inspection is not possible.
1A Under any condition
GROUND Body ground 1.0 or less Body ground
F
2A GROUND Body ground Under any condition 1.0 or less Body ground
2B GROUND Body ground Under any condition 1.0 or less Body ground
Switch the ignition to ACC or ON
B+
2C ACC relay control ACC relay (engine off or on) ACC relay
Ignition switched off 1.0 or less
2E* Clutch pedal Clutch pedal not depressed B+ Clutch pedal position
Clutch pedal position switch
2 position switch Clutch pedal depressed 1.0 or less switch
2F* LF control unit Because this terminal is for communication, integrity determination
LF control unit
3 communication using terminal voltage inspection is not possible.
Ignition Selector lever at
B+
2G switch position except P
Shift lock Shift lock solenoid ON Selector lever at P Shift lock solenoid
*1 (engine position and brake 1.0 or less
off or on) pedal depressed
2H* LF control unit Because this terminal is for communication, integrity determination
LF control unit
3 communication using terminal voltage inspection is not possible.
2I* Keyless antenna (inside Keyless antenna Because this terminal is for communication, integrity determination
4 vehicle, center) (interior, center) using terminal voltage inspection is not possible.
Push button start pressed 1.0 or less
2J Push button start 2 Push button start Push button start
Push button start not pressed B+
2K* Keyless antenna (inside Keyless antenna Because this terminal is for communication, integrity determination
4 vehicle, center) (interior, center) using terminal voltage inspection is not possible.
2L* Under any condition
GROUND Shield ground 1.0 or less Body ground
4
Because this terminal is for communication, integrity determination
2M HS-CAN+ -
using terminal voltage inspection is not possible.
Because this terminal is for communication, integrity determination
2O HS-CAN- -
using terminal voltage inspection is not possible.
Keyless receiver power Under any condition
2Q Keyless receiver Approx. 5 Keyless receiver
supply
Keyless receiver Because this terminal is for communication, integrity determination
2R Keyless receiver
communication using terminal voltage inspection is not possible.
Ignition switched ON (engine off
B+
2S IG1 relay control IG1 relay or on) IG1 relay
Ignition switched off or at ACC 1.0 or less
When cranking B+ • Starter relay
2V Starter relay Starter relay Except above *7 1.0 or less, • PCM
or B+*7 • Start stop unit
Under any condition • AT 15 A fuse
2W Power supply AT 15 A fuse B+ • Battery
• DC-DC converter*8
Under any condition • SRS2 / ESCL 15 A
SRS2 / ESCL 15 A fuse
2X Power supply (ESCL) B+ • Battery
fuse
• DC-DC converter*8
*1 : ATX
*2 : MTX
*3 : With advanced keyless entry system
*4 : With keyless entry system
*5 : With steering shift switch
*6 : With smart city brake support (SCBS)
*7 : Because the voltage varies depending on the vehicle conditions, examination using the terminal voltage
inspection is not possible.
*8 : With i-ELOOP