Professional Documents
Culture Documents
5. Dirt Grooves - Dirt grooves shall be provided where necessary for GO members above 120 mm up
to 200 mm. The dimensions (Reaffirmed
of the dirt grooves with ,U’ shape shall have width 4 mm and the 2008)
depth
shall be such that it clears the minor diameter d the plug gauges.
6, Designation
6.1 Gauging members for screw plug gauges shall be designated by the name of the (Reaffirmed
gauging 2007)
member
GO or NO GO, nominal diameter, pitch and the tolerance class according to IS : 4218 ( Part IV)-1976
‘IS0 metric screw threads: Part IV Tolerancing system’. If the pitch is not indicated in the designation,
:oarse pitch shall be implied.
Example
(Reaffirmed 2006)
GO or NO GO gauging members of screw plug gauges of nominal diameter 125 mm, pitch
3 mm and tolerance class 6H shall be designed as:
and
3.3 GO or NO GO screw check plug gauging member for solid NO GO screw ring gauge of nominal
diameter 125 mm, pitch 3 mm and tolerance class 6 g. shall be designated as:
and
j-4 lf the dirt groove is provided for GO screw plug gauge of nominal diameter 125 mm, pitch 3 mm
jnd tolerance class 6H, it shall be designed as:
IS : 10685 - 1983
TABLE 1 DIMENSIONS FOR GAUGING MEMBERS FOR GO AND NO GO SCREW PLUG GAUGES
AND SCREW CHECK PLUG GAUGES ( SIZE RANGE ABOVE Ml20 UP TO
AND INCLUDING M200)
( Clause 3 )
LJGR~ovES ’
bOAND bl BLANKS EQUALLY SPACED b2 AND b3 BLANKS
~RIto.25mm
I
1.85mm min
DETAIL OF GROOVE
!I
-~___ meter - ____~__ -~ _
4
Ab-
ove %I’,0
IncllJ
Pitches
for GO
Gauges
L
I Pitches
for GO
Gauges
L t Pitches
for GO
Gauges
L f Pitcher j
for GO
Gauge: j
L t
ding
- -.- -.- ,__~ _ .~ --._..
I-120 140 9 100 5 2 16 3 25 5 4 35 IO 6 50 12
-__ __._
2
Free Standard provided by BIS via BSB Edge Private Limited to Hariom Instru-Labs -
Ahmedabad(mechanicalhariom@gmail.com) 59.94.197.115 [for non-commercial
IS : 10665 -use only].
1983
7. General Requirements
7.1 Other requirements for gauging members not covered in this standard, shall ccnform to IS : 7018
( Part 1 ) - 1983 ‘Technical supply condrtions for gauges: Part I General’ ( first revision ).
7.2 The gauge handles shall be according to IS :5388-1983 ‘Handles for plug gauges, plain and
threaded ( second revision )‘.
8 .l IS/ Cerlificafion Marking - Details available with the Ir.dian Standards Institution.
EXPLANATORY NOTE
Gauging members for screw plug gauges GO and NO GO members have been combined to
cover the requirements of GO and NO GO gauging members in one standard.
The gauging members in this range are of trilock type. This extends the interchangeable end
system to the larger size.
An additional advantage of this type of gauge is that the gauging members can be, reversed
when the entering end is worn out. The wedge shaped prongs on the handle are engaged with
corresponding grooves in the gauging members by a single screw providing a self centring support with
a positive lock and a degree of rigidity equivalent to that of a solid gauge.
The requirements of the gauging members for size range Ml to M 40 and from above M40
up to and including Ml20 have been covered in separate standards.
3
--.---
Prmted at Arcm Prmr, NW Delhi, India