Professional Documents
Culture Documents
457.3
18" Typical Handmade Ebony
Typical Frets are Nickel/Silver 638.2 Tailpiece. Refer To Details
Bead = .106" (2.7mm) Wide x 25 1/8"
.044" (1.12mm) Hign. F-Hole In Carved Top
Fretboard Support
4.6
3/16"
Neck Section
17.8
11/16"
Neck Section
Carved Spruce Top-Refer
16.6
21/32"
41. 5 "
8
To Plate Contour Map and
1 5/ Plate Sections For Profiles ABS Plastic Binding:
14.6
9/16"
2.29mm x 6.35 W/ BW
2 31/32"
14.56"
9/1
41. 5 Side Plates: Maple 3/32" Thick Purfling On Bottom
75.7
15 /8"
14.10° (2.4mm) Consider Figured Refer To Binding Detail
Note That Headpiece Tapers ABS Plastic Fretboard Binding: Dashed Lines Indicate Neck Slot Wood Such As Birds-Eye
From 12.7mm To 14.5mm Binding: 2.29mm x 6.35mm For Dual Action Adjustable Truss Or Curly Maple. Back & Side
Purfling: Rod. Wood Must Match.
Neck Section
Black: 0.5mm x 2.0mm
White: 0.5mm x 2.0mm Vertical Grain Maple Neck
Black: 0.5mm x 2.0mm Either One Piece Or Laminate
White: 0.5mm x 2.0mm For Additional Strength
2.5 2.0 41.0 2.0 2.5 2.5 2.0 46.0 2.0 2.5
Nut Details Carved Maple Guitar Back Plate.
1/32"
1/32"
3/32" 3/32" 1 5/8" 3/32" 3/32" 3/32" 3/32" 1 13/16" 3/32" 3/32"
1/4"
7/32"1.0
7/32"1.0
6.4
Match Side Wood. Consider Either
9. 4 "
3/8
12.7"
Ebony or East Indian Ebony or East Indian Birds-Eye Maple or Curly Maple
1/2
5.3
5.3
Binding: 3.4mm x 1.52mm 3+3 - Perloid Keystone BTN - Tuners - Nickel or Gold Rosewood Fretboard Rosewood Fretboard
1/32"
1/32"
1/32"
15/32"
1.0
1.0
1.0
w/9.5" (241mm) Radius w/9.5" (241mm) Radius
11.6
Purfling: Finish.
Black: 0.5mm x 3.4mm
White: 0.5mm x 3.4mm Note: This Drawing Shows the Traditional Benedetto Two-way Adjustable Two-way Adjustable
Truss Rod Truss Rod
14.6
Peghead Shape for Reference Only.
9/16"
21/32"
Black: 0.5mm x 3.4mm
16.6
11/16"
17.8
White: 0.5mm x 3.4mm You Should Design Your Own Shape to Make This
Instrument Unique and Not Copy Other Copyrighted 5.5
7/32"
Shapes
R 304.8 R 304.2
15/32"
12.2
4.60°
4.6 Spruce X-Brace Spruce X-Brace
3/16"
5/32"
4.1
5/32"
4.3
1/8"
3.5
Vertical Grain Mahogany Kerfed Lining: Consider Spruce or
ABS Plastic Binding @ Headpiece: Or Spruce Head Block Mahogany Fine-Grained Wood Spruce Side Brackets/Braces
2 5/8"
66.5
Dual Action 14-1/2" Long Truss Rod w/ Hex Extend To Top And Back Plates
2 5/8"
66.5
Binding: 3.4mm x 1.52mm 14.10° If A Pickup And Electronics
Purfling: Adjustment at Neck End. Route Channel Vertical Grain Maple Neck Dovetail Neck Joint Carve Relief's At Brace Sides Are Added To Guitar, Modify
Black: 0.5mm x 3.4mm In Neck So Truss Rod is Slightly Below Either One Piece Or Laminate As Shown Button To Accept 1/4" Phone
White: 0.5mm x 3.4mm Surface of Neck (.25mm). Apply 3/4" Wide For Additional Strength Plug Jack.Centered In Button
Black: 0.5mm x 3.4mm Masking Tape Over Rod Channel Prior to
White: 0.5mm x 3.4mm Gluing Fretboard.
3/16"
3/16"
3. 4 " Truss Rod Cover. Multi-layer
4.7
4.7
1/8 ABS Plastic With Beveled Edge Finger Rest Attachement 5.0
Block. Attach To Side Of Apply Wire Hold-Down Clips ABS Plastic Binding: 3/16" Spruce or Mahogany
Neck Extension With (2) To Bottom of Finger Rest Tail Block. Vertical
3. 4 "
2 9/32"
58.3
415/8"
1
.4
11.4