Professional Documents
Culture Documents
Hook
NFC Cover
Rib
Groove
No. Screw Type
S3 C.B.S-TITE, SCREW, 3X8, F/ZB-3C
ADF Cover
ADF Cover
ADF Unit
SCN Unit
1. Close the ADF Unit. To prevent ADF Unit from opening by the hinge force, secure the ADF Unit to the
2. Remove the two screws (S8: ). SCN Unit as follows. It is dangerous if the ADF Unit opens during repair work, so
3. Open the ADF cover. make sure to secure it firmly.
4. Remove the screw (S8: ) near the marking “x12S” on the frame.
5. Secure the ADF Unit to the SCN Unit by inserting the screw (S8: ) removed in step 4 into
the hole A and tightening it.
6. Close the ADF cover.
Bracket
SCN Unit
SC Arm
ADF hinge
If you open the ADF/SCN without removing the screw, the hinges will be damaged. Before proceeding to the next step, make sure:
Make sure to remove the screw before opening it. • The four screws on the ADF Hinge are removed.
• The ADF Unit and the SCN Unit are secured. (p.676)
7. Remove the total of four screws (S1: ) on both left and right of the ADF Hinge. 8. Set up the SC Arm while lifting up the ADF Unit and SCN Unit.
9. Fix the Bracket at the lower of the SCN Unit by the hook of the SC Arm to support the
ADF Unit and SCN Unit.
C H E C K Make sure the Hook Lever on the SC Arm clicks in place and the bracket is
P O IN T
secured firmly.
To close the ADF Unit and SCN Unit, push the Hook Lever of the SC Arm, and
remove the Bracket of the SCN Unit from the SC Arm.
Stacker Unit
Hole
Front Tray Guide
Hook
Hook
Stacker Unit
Stacker Lever
1. Open the Stacker Unit. 1. Remove one screw with stopper (S10: ).
2. Remove one screw with stopper (S10: ). 2. Slide the Rear Tray Guide in the direction of the arrow, then remove it.
3. Slide the Front Tray Guide in the direction of the arrow, then remove it while avoiding the C H E C K If the Stacker Unit is fully opened, it is difficult to remove the Rear Tray Guide. To
Stacker Lever. P O IN T
remove it easily, slightly open the Stacker Unit after loosening the screw.
C H E C K If the Stacker Unit is fully opened, it is difficult to remove the Front Tray Guide. To
P O IN T
remove it easily, slightly open the Stacker Unit after loosening the screw. When installing the Rear Tray Guide, align the two hooks with the holes of the
Stacker Unit, then attach it.
When installing the Front Tray Guide, align the two hooks with the holes of the
Stacker Unit, and then attach it.
Stacker Unit
Housing
Frame
Dowel 2
Cutout B
Positioning Hole
1. Remove the two black screws (S3: ), slide it in the direction of the arrow, and remove the 1. Open the Stacker Unit as wide as it goes.
Cable Cover. 2. Remove the two screws with stopper (S10: ).
To install the cable cover, hook the seven hooks on the holes of frame (x4) and 3. Lift up the Reverse Guide Plate a little.
housing (x3). 4. Remove the cutout A of the Reverse Guide Plate from the dowel 1, remove the cutout B of
the Reverse Guide Plate from the dowel 2, and remove the Reverse Guide Plate.
When installing the Reverse Guide Plate, fit the dowel (x2) to the positioning hole
(x2) of the Reverse Guide Plate.
Head
Hole in
Head
1. Loosen the one screw (S25: ) fixing the Head Lifting Lever. 2. Lift up the head and then hook the tip of the Head Lifting Jig into the hole of the head.
3. Hook the Head Lifting Jig on the frame as shown in the figure above.
4. Slide the Head Lifting Lever in the direction of the arrow, and insert it below the head.
5. Tighten the one screw to fix the Head Lifting Lever.
Connector
Positioning Hole
1. Release the cable from the clamp (x1). When installing the Static Eliminator Brush, pay attention to the following points.
2. Pinch both ends of the Cable Holding fixed to the frame, then remove it. Insert the Static Eliminator Brush in the direction of the arrow from the hole at the
3. Disconnect the connectors (x2). rear while taking care not to bang it against the frame or surrounding parts.
4. Remove the one screw (S9: ). Insert the tip of the frame of the Static Eliminator Brush into the positioning hole
of the receiving part located on the inner side of the front and then fix the Static
5. Pull out the Static Eliminator Brush in the direction of the arrow while taking care not to
Eliminator Brush in place.
bang it against the frame.
OUTLINE
Time
Part or Component Guide Disassembly/ Adjustment/
Total
Reassembly Inspection
DISASSEMBLY FLOWCHART
Start
B7 Cable Cover
C7 (→P. 765)
EJ Unit
A1
EJ Unit
NG EJ Unit Slide Rail B OK EJ Unit Slide Rail B
Hook
EJ Unit
Hook
EJ Unit NG Lever
When the EJ Unit Rail of the EJ Unit is supplied as ASP, one on the machine side (EJ
C H E C K When installing the EJ Unit, be aware of the following points.
P O IN T
Unit Slide Rail B) and the other on the EJ unit side (EJ Unit Slide Rail A) are supplied If you feel an abnormal load when installing the EJ Unit, do not force to push it.
as a pair. Remove it to check the condition, then try to install it again.
EJ Unit Slide Rail A which is a part on the machine side becomes unnecessary in Install it after checking the conditions of the bearing part on the EJ Unit Slide Rail
replacing. Remove it. B (x2). The EJ Unit Rail might be damaged if it is being installed in the "NG"
1. Pull out the EJ Unit until it stops. condition shown above.
2. While pushing the hook (x2) on the EJ Unit Slide Rail A, pull out the EJ Unit and remove Do not install and remove it when the relay unit is installed.
it. Insert the EJ Unit into the correct position while opening the Front Cover and
pushing the lever shown above.
B1 C1 B2 C2
SCN Rear Cover NFC Cover
Rear
NFC Cover
Rib
Groove
No. Screw Type No. Screw Type
S18 C.SHOULDER S-TITE, SCREW, 3X5 S3 C.B.S-TITE, SCREW, 3X8, F/ZB-3C
1. Remove the three screws (S18: ), remove the SCN Rear Cover. 1. Remove one black screw (S3: ).
2. Slide the NFC Cover in the direction of the arrow, and remove it.
To install the NFC Cover, fit the four Ribs of the NFC Cover to the Grooves of the
NFC Cover Inner, slide it in the rear direction.
B3 C3 B4 C4
SCN Housing Cap Open the ADF/SCN.
ADF Unit
Hook
ADF Cover
ADF hinge
SCN Unit
ADF hinge
To prevent ADF Unit from opening by the hinge force, secure the ADF Unit to the If you open the ADF/SCN without removing the screw, the hinges will be damaged.
SCN Unit as follows. It is dangerous if the ADF Unit opens during repair work, so Make sure to remove the screw before opening it.
make sure to secure it firmly.
4. Remove the screw (S8: ) near the marking “x12S” on the frame. 7. Remove the total of four screws (S1: ) on both left and right of the ADF Hinge.
5. Secure the ADF Unit to the SCN Unit by inserting the screw (S8: ) removed in step 4 into
the hole A and tightening it.
6. Close the ADF cover.
Bracket
Stacker Unit
SCN Unit
Hole
Front Tray Guide
Hook Lever
SC Arm
Hook
Stacker Lever
Before proceeding to the next step, make sure: 1. Open the Stacker Unit.
• The four screws on the ADF Hinge are removed. 2. Remove one screw with stopper (S10: ).
• The ADF Unit and the SCN Unit are secured. (p.676) 3. Slide the Front Tray Guide in the direction of the arrow, then remove it while avoiding the
8. Set up the SC Arm while lifting up the ADF Unit and SCN Unit. Stacker Lever.
9. Fix the Bracket at the lower of the SCN Unit by the hook of the SC Arm to support the C H E C K If the Stacker Unit is fully opened, it is difficult to remove the Front Tray Guide. To
ADF Unit and SCN Unit. P O IN T
remove it easily, slightly open the Stacker Unit after loosening the screw.
C H E C K Make sure the Hook Lever on the SC Arm clicks in place and the bracket is
P O IN T
secured firmly. When installing the Front Tray Guide, align the two hooks with the holes of the
To close the ADF Unit and SCN Unit, push the Hook Lever of the SC Arm, and Stacker Unit, and then attach it.
remove the Bracket of the SCN Unit from the SC Arm.
B6 C6 B7 C7
Rear Tray Guide Cable Cover
Housing
Frame
Cable Cover
Hook
1. Remove one screw with stopper (S10: ). 1. Remove the two black screws (S3: ), slide it in the direction of the arrow, and remove the
2. Slide the Rear Tray Guide in the direction of the arrow, then remove it. Cable Cover.
C H E C K If the Stacker Unit is fully opened, it is difficult to remove the Rear Tray Guide. To To install the cable cover, hook the seven hooks on the holes of frame (x4) and
P O IN T
remove it easily, slightly open the Stacker Unit after loosening the screw. housing (x3).
When installing the Rear Tray Guide, align the two hooks with the holes of the
Stacker Unit, then attach it.
B8 C8
Stacker Unit Front Housing Assy
Front
Hinge
Stacker Unit
Front Cover
1. Close the Stacker Unit. 1. Raise up the Front Cover and remove it from the Hinge.
2. Remove the four screws (S11: ).
3. Open the Stacker Unit and remove it.
Housing FD
C10 C11
FD Sub Tray Stacker Sub Cover
Stacker Unit
FD Sub Tray
Rib
Hole
Stacker Sub Cover
1. Open the Stacker Unit as wide as it goes. 1. Remove the three screws (S1: ), then remove the Stacker Sub Cover.
2. Remove the two screws with stoppers (S1: ), then remove the FD Sub Tray.
When installing the FD Sub Tray, insert the ribs (x2) into the holes indicated in the
figure above before fixing with screws.
Right Side
Connector
MP Tray Unit
Connector
When installing the Before Duplex Confluence Plate, align the ribs of the Before When installing the Tray Lift Unit, align the ribs and the positioning holes in the Tray
Duplex Confluence Plate with the positioning holes in the frame as shown in the Lift Unit shown in the figure above, then attach it.
figure above, and then attach it.
OUTLINE
Time
Part or Component Guide Disassembly/ Adjustment/
Total
Reassembly Inspection
DISASSEMBLY FLOWCHART
Start
B10 Housing FD C10 Reverse Guide Plate
(→P. 781) D10 (→P. 783)
A1 B1 Belt Cover
C1 D1 (→P. 772)
B11 Paper Guide End Assy C11 Drive Gear Cover
(→P. 782) D11 (→P. 784)
A2 B2 Front Housing Assy
C2 D2 (→P. 772)
C12 Helical Gear, T32
D12 (→P. 784)
B3 C3 SCN Rear Cover A3 Drive Gear Cover
D3 (→P. 776) (→P. 773)
C13 Duplex Roller, 2 D13 Housing Rear, Right
(→P. 785) (→P. 785)
B4 C4 NFC Cover A4 Helical Gear, T32
D4 (→P. 777) (→P. 773)
D14 Housing Rear, Left
(→P. 786)
B5 C5 SCN Housing Cap A5 Open the MP Tray Unit.
D5 (→P. 777) (→P. 774)
D15 Open the Board Box
(→P. 786)
B6 C6 A6
Open the ADF/SCN Cable Cover C1, Upper
D6 (→P. 778) (→P. 775)
D16 Duplex Feed Clutch
(→P. 787)
B7 C7 Front Tray Guide A7 Paper Assist Assy
D7 (→P. 780) (→P. 775)
D17 Duplex Roller, 3
(→P. 788)
A1 B1 C1 A2 B2 C2
Belt Cover Front Housing Assy
D1 D2
Front
Front Cover
Hinge
Front Cover
Tab
Belt Cover
1. Open the Front Cover. 1. Raise up the Front Cover and remove it from the Hinge.
C H E C K The screw of the belt cover cannot be removed because there is a stopper.
P O IN T
2. Loosen the two screws (S4: ), then remove the belt cover in the direction of the arrow.
Insert the tab (x2) into the hole of the front housing before installing the belt cover.
2. Open the I/C Cover. 1. Release the cable from the clamps (x6).
3. Remove the 11 screws (S7: ), then remove the Front Housing Assy. 2. Remove the four screws (S1: ), then remove the Drive Gear Cover.
A4 A5
Helical Gear, T32 Open the MP Tray Unit.
Right Side
Front E Ring 4
MP Tray Unit
B
A
C
Stopper Ring
C H E C K If a Helical Gear, T32 needs to be removed not to be replaced but to proceed with 1. Open the MP Tray Unit.
P O IN T
disassembly, refer to the following and remove the appropriate Helical Gear, T32.
1. Remove the Stopper Ring or E Ring 4, then remove the Helical Gear, T32.
A6 A7
Cable Cover C1, Upper Paper Assist Assy
Hole
1. Remove the one screw (S1: ), then remove the Cable Cover C1, Upper. 1. Remove the one screw (S1: ).
When installing the Cable Cover C1, Upper, align the dowels with the positioning 2. Slide the Paper Assist Assy in the direction of the arrow, and remove it.
holes. When installing the Paper Assist Assy, pass the Link Lever through the hole in the
Take care not to catch the cable. Paper Assist Assy and then align the tabs (x5) with the cutouts in the frame.
A8 B3 C3
Duplex Roller, 1 SCN Rear Cover
D3
Front Rear
Bearing
Stopper Ring
1. Remove the Stopper Ring. 1. Remove the three screws (S18: ), remove the SCN Rear Cover.
2. Remove the bearing from the hole in the frame.
3. Slide Duplex Roller, 1 to the front and remove the protrusion of the One Way Bearing
from the hole in the frame.
4. Remove the Duplex Roller, 1 while taking the shaft out of the hole in the frame.
B4 C4 B5 C5
NFC Cover SCN Housing Cap
D4 D5
Hook
NFC Cover
Rib
Groove
No. Screw Type
S3 C.B.S-TITE, SCREW, 3X8, F/ZB-3C
ADF Cover
ADF Cover
ADF Unit
SCN Unit
1. Close the ADF Unit. To prevent ADF Unit from opening by the hinge force, secure the ADF Unit to the
2. Remove the two screws (S8: ). SCN Unit as follows. It is dangerous if the ADF Unit opens during repair work, so
3. Open the ADF cover. make sure to secure it firmly.
4. Remove the screw (S8: ) near the marking “x12S” on the frame.
5. Secure the ADF Unit to the SCN Unit by inserting the screw (S8: ) removed in step 4 into
the hole A and tightening it.
6. Close the ADF cover.
Bracket
SCN Unit
SC Arm
ADF hinge
If you open the ADF/SCN without removing the screw, the hinges will be damaged. Before proceeding to the next step, make sure:
Make sure to remove the screw before opening it. • The four screws on the ADF Hinge are removed.
• The ADF Unit and the SCN Unit are secured. (p.676)
7. Remove the total of four screws (S1: ) on both left and right of the ADF Hinge. 8. Set up the SC Arm while lifting up the ADF Unit and SCN Unit.
9. Fix the Bracket at the lower of the SCN Unit by the hook of the SC Arm to support the
ADF Unit and SCN Unit.
C H E C K Make sure the Hook Lever on the SC Arm clicks in place and the bracket is
P O IN T
secured firmly.
To close the ADF Unit and SCN Unit, push the Hook Lever of the SC Arm, and
remove the Bracket of the SCN Unit from the SC Arm.
B7 C7 B8 C8
Front Tray Guide Rear Tray Guide
D7 D8
Stacker Unit
Hole
Front Tray Guide
Hook
Hook
Stacker Unit
Stacker Lever
1. Open the Stacker Unit. 1. Remove one screw with stopper (S10: ).
2. Remove one screw with stopper (S10: ). 2. Slide the Rear Tray Guide in the direction of the arrow, then remove it.
3. Slide the Front Tray Guide in the direction of the arrow, then remove it while avoiding the C H E C K If the Stacker Unit is fully opened, it is difficult to remove the Rear Tray Guide. To
Stacker Lever. P O IN T
remove it easily, slightly open the Stacker Unit after loosening the screw.
C H E C K If the Stacker Unit is fully opened, it is difficult to remove the Front Tray Guide. To
P O IN T
remove it easily, slightly open the Stacker Unit after loosening the screw. When installing the Rear Tray Guide, align the two hooks with the holes of the
Stacker Unit, then attach it.
When installing the Front Tray Guide, align the two hooks with the holes of the
Stacker Unit, and then attach it.
B9 C9 B10
Cable Cover Housing FD
D9
Frame
Housing FD
Cable Cover
Hook
1. Remove the two black screws (S3: ), slide it in the direction of the arrow, and remove the 1. Close the Stacker Unit.
Cable Cover. 2. Remove the four black screws (S3: ), then remove the Housing FD.
To install the cable cover, hook the seven hooks on the holes of frame (x4) and
housing (x3).
Connector Connector
Front
Bearing
Clamp
Shaft of EJ Roller 5
Connector
Stopper Ring
Dowel 2
Cutout B
Dowel
Positioning Hole
Be careful not to touch the Static Eliminator Brush of the Paper Guide End Assy when 1. Open the Stacker Unit as wide as it goes.
attaching the Paper Guide End Assy. 2. Remove the two screws with stopper (S10: ).
3. Lift up the Reverse Guide Plate a little.
6. Remove the Paper Guide End Assy in the direction of the arrow. 4. Remove the cutout A of the Reverse Guide Plate from the dowel 1, remove the cutout B of
Insert the tips of the comb-shaped part of the Paper Guide End Assy between the EJ the Reverse Guide Plate from the dowel 2, and remove the Reverse Guide Plate.
Roller 5 and Star Wheel Parts shown in the figure above while lowering the Star When installing the Reverse Guide Plate, fit the dowel (x2) to the positioning hole
Wheel Parts with a finger. (x2) of the Reverse Guide Plate.
C11 C12
Drive Gear Cover Helical Gear, T32
D11 D12
Front
Front E Ring 4
Clamps
A
C
Stopper Ring
1. Release the cable from the clamps (x6). C H E C K If a Helical Gear, T32 needs to be removed not to be replaced but to proceed with
P O IN T
2. Remove the four screws (S1: ), then remove the Drive Gear Cover. disassembly, refer to the following and remove the appropriate Helical Gear, T32.
1. Remove the Stopper Ring or E Ring 4, then remove the Helical Gear, T32.
C13
Duplex Roller, 2 Housing Rear, Right
D13
Rear Right
Rear
Bearing
Dowel
Front
Bearing
Hook
Dowel
No. Screw Type
S7 C.B.S-TITE(P4), SCREW, 3X10, F/ZN-3C
1. Remove the Stopper Ring at the rear and remove the bearing from the frame. 1. Remove the six screws (S7: ).
2. Move the shaft at the rear of the Duplex Roller, 2 in the direction of the arrow to remove it 2. Slide the Rear Right Housing in the direction of the arrow, then disengage the three hooks.
from the frame and insert it into the hole in the frame shown in the figure above. 3. Remove the Rear Right Housing while remove the two dowels.
3. Slide the Duplex Roller, 2 toward the rear to remove the bearing at the front from the
frame and then remove Duplex Roller, 2.
Board BOX
Hook
Hook Rib
No. Screw Type No. Screw Type
S7 C.B.S-TITE(P4), SCREW, 3X10, F/ZN-3C S1 C.B.S-TITE R, SCREW, 3X8, F/ZN-3C
1. Remove the three screws (S7: ). 1. Remove the three screws (S1: ).
2. Slide the Rear Left Housing in the direction of the arrow to disengage the two hooks, and 2. Lift up the Board BOX a little, disengage the two hooks, and open the Board BOX.
remove the Rear Left Housing.
When installing the Rear Left Housing, fix it with the hooks after fitting the three ribs
to the hole on the frame, then tighten the screws.
Connector
Hook
Stopper Ring
Rib
3. To fix the Board Box while it is in the open state, remove the Board Box fixed wire from 1. Disconnect the connector.
the Rib of the Board Box and hook it onto the hook on the printer side. 2. Release the cable from the clamps (x4).
Do not attempt to close the Board Box while the Board Box Fixed Wire is hooked 3. Remove the Stopper Ring.
onto the hook on the printer side because the Board Box Fixed Wire will be bent and 4. Pull off the Duplex Feed Clutch from the shaft.
the Board Box will become unable to be fixed.
When installing the Duplex Feed Clutch, align the rib of the Duplex Feed Clutch with
the frame as shown in the figure above.
Duplex Roller, 3
Duplex Roller, 3
Front Bearing Rear
D17
1
Rear Bearing
Stopper Ring Front Frame Duplex Roller, 3
Rear Frame
3
Duplex Roller, 3
Stopper Ring
Front
Bearing
6
Stopper Ring
Stopper Ring
1. Remove the Stopper Ring at the rear. Install the Duplex Roller, 3 with the following procedure.
2. Slide the Duplex Roller, 3 in the direction of the arrow to remove the bearing at the front 1. Install only the bearing at the front of the Duplex Roller, 3.
from the frame. 2. Move the bearing as near to the roller as possible and then insert the shaft at the
3. Pull out the Duplex Roller, 3 from the rear bearing to remove it. front in the hole of the front frame.
3. Insert the rear shaft of the Duplex Roller, 3 into the hole of the bearing.
4. Slide the Duplex Roller, 3 to the rear and then align the position of the front
bearing with the groove of the shaft and fix it with the Stopper Ring.
5. Fix the bearing at the front to the hole in the frame.
6. Attach the Stopper Ring to the groove of the shaft at the rear to fix the Duplex
Roller, 3 in place.
OUTLINE
Time
Part or Component Guide Disassembly/ Adjustment/
Total
Reassembly Inspection
DISASSEMBLY FLOWCHART
Start
A2 B2 Front Housing Assy C11 Helical Gear, T26 C20 Paper Guide End Assy
C2 D2 (→P. 791) D11 (→P. 798) D20 (→P. 804)
B4 Paper Guide End Sub C13 NFC Cover D22 Paper Guide End
C4 D4 (→P. 793) D13 (→P. 799) (→P. 806)
A1 B1 C1 A2 B2 C2
Belt Cover Front Housing Assy
D1 D2
Front
Front Cover
Hinge
Front Cover
Tab
Belt Cover
1. Open the Front Cover. 1. Raise up the Front Cover and remove it from the Hinge.
C H E C K The screw of the belt cover cannot be removed because there is a stopper.
P O IN T
2. Loosen the two screws (S4: ), then remove the belt cover in the direction of the arrow.
Insert the tab (x2) into the hole of the front housing before installing the belt cover.
Paper Guide, 3
Hook and Hole
Hook and
Hole
B4 C4 C5
Paper Guide End Sub Housing Rear, Right
D4 D5
Hook
Hook
Dowel
No. Screw Type No. Screw Type
Paper Guide End Sub
S1 C.B.S-TITE R, SCREW, 3X8, F/ZN-3C S7 C.B.S-TITE(P4), SCREW, 3X10, F/ZN-3C
1. Remove the leg of the Torsion Spring from the Paper Guide End Sub. 1. Remove the six screws (S7: ).
2. Remove the E Ring 4 and remove the Torsion Spring. 2. Slide the Rear Right Housing in the direction of the arrow, then disengage the three hooks.
3. Remove the one screw (S1: ), then remove the Paper Guide End Sub Right Shaft. 3. Remove the Rear Right Housing while remove the two dowels.
4. Slide the Paper Guide End Sub in the direction of the arrow, and remove it.
C6 C7
Housing Rear, Left Open the Board Box
D6 D7
Board BOX
Hook
Hook Rib
No. Screw Type No. Screw Type
S7 C.B.S-TITE(P4), SCREW, 3X10, F/ZN-3C S1 C.B.S-TITE R, SCREW, 3X8, F/ZN-3C
1. Remove the three screws (S7: ). 1. Remove the three screws (S1: ).
2. Slide the Rear Left Housing in the direction of the arrow to disengage the two hooks, and 2. Lift up the Board BOX a little, disengage the two hooks, and open the Board BOX.
remove the Rear Left Housing.
When installing the Rear Left Housing, fix it with the hooks after fitting the three ribs
to the hole on the frame, then tighten the screws.
Rear
Ink Supply
Unit
Cutout
Grounding
wire
Hook
Frame Stay
Cable
Rib Clamp
Board BOX
Pressure
Pump Unit
Maintenance Grounding
Unit wire
Hole
No. Screw Type
Rib S1 C.B.S-TITE R, SCREW, 3X8, F/ZN-3C
3. To fix the Board Box while it is in the open state, remove the Board Box fixed wire from 1. Remove one each screw (S1: ) and remove one each Grounding Cable from the following
the Rib of the Board Box and hook it onto the hook on the printer side. units.
Do not attempt to close the Board Box while the Board Box Fixed Wire is hooked Ink Supply Unit (x1), Pressure Pump Unit (x1), Maintenance Unit (x1)
onto the hook on the printer side because the Board Box Fixed Wire will be bent and 2. Remove the four screws (S1: ).
the Board Box will become unable to be fixed. 3. Release the two cables from the Cable Clamp, then remove the Frame Stay.
When installing the Frame Stay, insert the lower rib into the hole on the frame and
then fit the upper rib with the cutout of the frame.
Pull the two cables connecting to the Pressure Pump Unit around the Cable Clamp
installed to the Frame Stay as shown above.
C9 C10
I/C Detector Ink Supply Unit
D9 D10
Gray tube
Hook
I/C Detector
1. Remove the CSIC FFC from the connector on the CSIC Relay Board. Gray tube is connected to the ink collection pack to prevent ink from leaking to
2. Peel off the CSIC FFC fixed by using the double side tape from the frame, release it from outside the printer. Make sure no ink collects on the ink tray in the unit.
the hook (x1).
3. Remove one screw (S1: ), then pull out the I/C Detector in the direction of the arrow. 1. Disconnect the gray tube from the Relay Ink Path Assy.
When installing the I/C Detector, fit the dowel of the Ink Supply Unit to the
positioning hole of the I/C Detector.
Rear
Rear
Ink Tube
Tube clips
2. Remove the two screws (S14: ), then remove the Supply Air Joint. C H E C K The Relay Joint Cap used in the next step is contained to the Relay Ink Path Assy
P O IN T
When the Supply Ink Joint is removed, the Ink may be discharged from the supplied as ASP.
connection point. Take care not to contaminate the periphery. Engage the protrusions on the Supply Joint, Ink with the grooves on the Relay
Joint Cap.
5. Remove the Supply Ink Joint, attach the Relay Joint Cap to the connection point of the
C H E C K The Tube Clips used in the next step are equipped to the container inside of the Front edge, and then fix it with the hook (x4).
P O IN T
Cover.
3. Hold all the Ink Tubes shown above two by two by the Tube Clip (x2).
4. Remove the two screws (S14: ) fixing the Supply Ink Joint.
Stopper Ring
Connector
6. Remove the Ink Supply Unit Cable from the connector. 1. Remove the Stopper Ring, then remove the Helical Gear, T26.
7. Remove the three screws (S1: ) and the three screws with stopper (S2: ), then remove
the Ink Supply Unit.
When installing the Ink Supply Unit, hook the hook (x2) of the upper Ink Supply Unit
on the Cutout on the frame.
C12 C13
SCN Rear Cover NFC Cover
D12 D13
Rear
NFC Cover
Rib
Groove
No. Screw Type No. Screw Type
S18 C.SHOULDER S-TITE, SCREW, 3X5 S3 C.B.S-TITE, SCREW, 3X8, F/ZB-3C
1. Remove the three screws (S18: ), remove the SCN Rear Cover. 1. Remove one black screw (S3: ).
2. Slide the NFC Cover in the direction of the arrow, and remove it.
To install the NFC Cover, fit the four Ribs of the NFC Cover to the Grooves of the
NFC Cover Inner, slide it in the rear direction.
C14 C15
SCN Housing Cap Open the ADF/SCN.
D14 D15
ADF Unit
Hook