Professional Documents
Culture Documents
GBSS12.0
Feature Parameter Description
Issue 01
Date 2010-06-30
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.
Website: http://www.huawei.com
Email: support@huawei.com
GSM BSS
Adjustment of Adaptive Timing Advance Contents
Contents
1 Introduction ................................................................................................................................1-1
1.1 Scope ............................................................................................................................................ 1-1
1.2 Intended Audience......................................................................................................................... 1-1
1.3 Change History.............................................................................................................................. 1-1
1 Introduction
1.1 Scope
This document describes the feature of adjustment of adaptive timing advance of Huawei Global System
for Mobile communications (GSM) Base Station Subsystem (BSS).
The feature involved is GBFD-110901 Adjustment of Adaptive Timing Advance.
Document Issues
The document issues are as follows:
01 (2010-06-30)
Draft (2010-03-30)
01 (2010-06-30)
This is the first release of GBSS12.0.
Compared with issue Draft (2010-03-30) of GBSS12.0, issue 01 (2010-06-30) of GBSS12.0 incorporates
the changes described in the following table.
Draft (2010-03-30)
This is the draft release of GBSS12.0.
3 Technical Description
By means of adjustment of adaptive timing advance, the TA offset of an MS can be reduced to +1 or -1
time length of a symbol.
In the GSM system, TDMA technology is applied over the Um interface. Each MS must transmit signals
in the assigned timeslot, and the BTS must receive the signals in the corresponding timeslot. Figure 3-1
shows the delay offset of signals received by the BTS when the MS is traveling away from position P1, to
P2, and then to P3.
It is assumed that the MS originally occupies timeslot 1 (TS1). That is, the signals transmitted by the MS
are expected to arrive at the BTS in TS1, as shown in Figure 3-1. When the MS is close to the BTS, the
transmission delay is short, and the BTS can receive signals from the MS right in TS1. As the MS travels
away from the BTS, the transmission delay is prolonged and the signals transmitted by the MS may
arrive at the BTS in a later TS if the TA is not adjusted. For example, as shown in Figure 3-1, when the
MS moves to P3, some signals from the MS arrive in TS2. These signals are overlapped by the signals
that are from other MSs and also arrive in TS2, and thus they cannot be decoded appropriately.
Figure 3-1 Signal reception with TA unchanged
P1 P2 P3
Ts1 Ts2 Ts1 Ts2 Ts1 Ts2
To avoid this problem, the base station subsystem (BSS) monitors the required transmission time of
each signal from the MS to the BTS and informs the moving MS of TA adjustment. Then, the MS
transmits signals with the adjusted TA. This ensures that all signals from the MS can be received by the
BTS in TS1, as shown in Figure 3-2.
A TA value ranges from 0 µs to 233 µs. The TA value affects the radio coverage of cells.
P1 P2 P3
Ts1 Ts2 Ts1 Ts2 Ts1 Ts2
In the GSM system, the TA value is an integer ranging from 0 to 63. It refers to the time required for
transmitting 0- to 63-bit data. If the TA value is 0, the MS need not transmit signals in advance; if the TA
value is 63, the distance between the MS and the BTS is the maximum, that is, approximately 35 km. If
the MS transmits signals at a distance greater than 35 km, the signals arrive at the BTS in the next
timeslot and cannot be decoded appropriately. By means of adjustment of adaptive timing advance, the
TA offset of the MS can be reduced to +1 or -1 time length of a symbol. By setting MAXTA, the BSC can
specify the maximum TA value of MSs in each cell. It is recommended that MAXTA of MSs in common
cells be set to 62.
4 Parameters
Table 4-1 Parameter description
Parameter NE MML Description
ID
MAXTA BSC6900 SET Meaning: This parameter specifies the
GCELLBASICPARA(Optional) actual coverage area of a cell. After
receiving the channel request message or
handover access message, the BTS
determines whether the channel
assignment or handover is performed in
the cell by comparing the TA and the
value of this parameter. The value of this
parameter is determined by that of "Cell
Extension Type" in the "ADD GCELL"
command.
5 Counters
For the counters,see the BSC6900 GSM Performance Counter Reference.
6 Glossary
For the acronyms, abbreviations, terms, and definitions, see the Glossary.
7 Reference Documents
[1] 3GPP TS 45.002: “Multiplexing and multiple access on the radio path”
[2] BSC6900 Feature List
[3] BSC6900 Optional Feature Description
[4] BSC6900 GSM Parameter Reference
[5] BSC6900 GSM MML Command Reference