Professional Documents
Culture Documents
2021-04-27 הגנה מפני ברקים
2021-04-27 הגנה מפני ברקים
The negatively charged area - אזור טעוןin the storm will send out a charge toward the
ground called a stepped or downward leader - נגן ראשי כלפי מטה.
When the downward leader gets close to the ground it is attracted - נמשךby positively
charged objects and a channel develops - ערוץ מתפתח.
You see the electrical transfer in this channel as lightning - ברק.
There may be several return strokes - משיכות החזרהof electricity within the established
channel that is seen as flickering lightning - ברק מהבהב.
The best lightning protection system will produce an upward leader - נגן ראשי כלפי למעלה
that is stronger than other nearby objects at an optimum time.
The lightning protection system must conduct the lightning discharge - הפריקות ברקים
through a continuous low impedance path to ground.
LIGHTNING PARAMETERS
Waveshape. T1/T2 -> 10/350
Protection Methods.
- Mesh method
- Rolling sphere method (RSM)
- Protection angle method (PAM)
Potential rise of the building’s earth-termination system with respect to the remote earth
caused by the peak value of the lightning current
Step potential:
Side flashing:
All down-conductors have a resistance and, more importantly,
inductance. During the lightning flash the rapid rate of
current rise can cause the inductive voltage rise of the
conductor to reach a magnitude where sufficient voltage
exists for the conductor to flashover to a nearby conductive
and earthed object.
Galvanic corrosion occurs when two dissimilar metals are in contact with each
other in the presence of an electrolyte.
קורוזיה גלוונית מתרחשת כאשר שתי מתכות שונות זו מזו במגע זו עם זו בנוכחות אלקטרוליט
In this situation, one metal becomes the anode and the other the cathode.
The anode will tend to go into solution and therefore corrode.
אנודה נוטה להיכנס לתמסה ומתחיל קורוזיה.במצב זה מתכת אחת הופכת לאנודה והשנייה לקתודה
For example, a bare copper conductor should not be directly connected to steel,
as the electrochemical potential difference is 0.53 V (≥ 0.5 V).
שכן הפרש הפוטנציאל, מוליך נחושת חשוף לא צריך להיות מחובר ישירות לפלדה,לדוגמא
) וולט0.5 ≥( וולט0.53 האלקטרוכימי הוא.
However, if the copper is tin plated then the difference becomes that of tin
(0.24 V), which is acceptable.
וזה מקובל,) וולט0.24( ההבדל הופך להיות זהה לפח, אם הנחושת מצופה בדיל,עם זאת.
Aluminum Aluminum
Copper Copper
Steel Aluminum
Zinc Aluminum
Natural components
Natural conductive components can be used as an integral part of the lightning
protection system.
.רכיבים מוליכים טבעיים יכולים לשמש כחלק בלתי נפרד ממערכת ההגנה מפני ברקים
Natural components are typically metallic structural items that will not be modified
during the life of the structure, such as reinforcing steel, metal framework.
, כגון פלדה מחזקת,רכיבים טבעיים הם בדרך כלל פריטים מבניים מתכתיים שלא ישונו במהלך חיי המבנה
מסגרת מתכתית.
Natural components must meet minimum material requirements and be electrically
continuous with secure interconnections between sections such as brazing, welding,
clamping, seaming, screwing or bolts.
רכיבים טבעיים חייבים לעמוד בדרישות החומר המינימליות ולהיות רציפים חשמלית עם חיבורים מאובטחים
הברגה או ברגים, תפר, הידוק, ריתוך,בין חלקים כגון הלחמה
Table. Minimum material thickness of metal pipes and sheets
for natural air-terminations.
• The overall resistance from top to ground level is less than 0.2 ohms.
• A major part of vertical and horizontal connections are welded or securely
connected.
𝑑 = 2 ∗ √2𝑟ℎ − ℎ2
Where:
d = distance between two rods (m)
r = radius of the rolling sphere (m)
h = height of the rods (m)
2
Where:
20
p = penetration distance (m)
r = radius of the rolling sphere (m)
d = distance between the two rods (m)
20
p=20-sqrt(20^2-(17/2)^2)=2m
d = 2*sqrt(2*r*h-h^2) = 2* sqrt(2*20*2-2^2) = 17.4 m
איור :1מרחב ההגנה של קולט ברק אנכי
בודד.
ראשית ,נחשב את גובה של המוט המתכת הנדרש להגנה על הבניין .לאחר מכן ,נבנה תוכנית משוערת של התחמ''ש ,ועל
התוכנית נסמן את רדיוס האזור המוגן .אז ,עם יהיה צוקך ,לקבע את המקום לקולט ברק נוסף.
𝑥𝐻 𝐻 −
∙ 𝐻 ∙ 𝑅𝑥 = 1.6
𝑥𝐻 𝐻 +
כאשר:
𝑥𝐻 – גובה המבנה המוגן6m – .
45 35
𝑚 𝑅𝑥 = √( )2 + ( )2 = 28.5
2 2
המתקן מצויד עם 4קולט ברקים נוספים (על איור :2תוכנית סידור ציוד משוער (ניתן להשיג דיאגרמה
מדויקת יותר לאחר השלמת רישומי בנייה) מסומן ב)lightning terminal – LT-
.1.1.2בחירת מגני ברק ל ,33 kVנמצאים לפני שנאי הספק.
מגני ברק מאפשר את הגבלת המתח ברשת לרמה המותרת עבור רמת הבידוד הדרוש.
מגן ברק הוא מייצג את הנגד לא לינארית בעלת מתח גבוה מאוד.
במתח העבודה העיקרי מגן ברק אינה משפיעה על פעולתו הרגילה של הציוד .התנגדות שלו מאוד גבוה.
כאשר התרחש מתח יתר ,ההתנגדות של המגן ברק צונחת בחדות ,מה שמוביל להגבלת המתח ברשת.
אחר שאימפולס במתח גבוה הסתיים ,ההתנגדות של מגן ברק חוזרת למצבה הרגיל (התנגדות גבוהה) והוא
מפסיקה להשפיע על רשת אספקת החשמל .פעימות מתח יתר ,לרוב קצרות מאוד ,והמגן ברק פועל במהירות
גבוהה מאוד ,שלא גורם את אספקת החשמל במערכת.
כאשר:
ממתח הנומינלי של רשת הספקת חשמל - Unom
מתח נומינלי של מגן ברק - Unom.Zn
מתח תפעולי מרבי של מגן ברק חייב להיות גבוה מהמתח הנומינלי של המערכת .2
)𝑈𝑛𝑜𝑚 ≤ 𝑈𝑀𝐶𝑂𝑉.𝑍𝑛1(2
כאשר:
-ממתח הנומינלי של רשת הספקת חשמל Unom
- UMCOV.Znמתח תפעולי מרבי של מגן ברק
מתח שיורי נקוב המתקבל ,כתוצאה ממעבר זרם אימפולס חייב להיות גבוה יותר .3
ממתח שיורי מחושב.
𝑚𝑜𝑛𝑈𝑟𝑒𝑠.𝑐𝑎𝑙 ≤ 𝑈𝑟𝑒𝑠.
כאשר:
מתח שיורי המחושב במערכת - 𝑙𝑎𝑐𝑈𝑟𝑒𝑠.
מתח שיורי הנומינלי הנשאר אחרי העברת זרם אימפולס - 𝑚𝑜𝑛𝑈𝑟𝑒𝑠.
𝑈𝑟𝑒𝑠.𝑐𝑎𝑙 ≤ 2.2 ∗ √2 ∗ 𝑈𝑝ℎ
נבחר מגן ברק .The 3EK7 surge arrester from Siemens - Metal oxide varistor (MOV) -
(נספח .) Error! Reference source not found. -
כאשר:
ממתח הנומינלי של רשת הספקת חשמל - Unom
מתח נומינלי של מגן ברק - Unom.Zn
מתח תפעולי מרבי של מגן ברק חייב להיות גבוה מהמתח הנומינלי של המערכת .2
תקין 𝑉𝑘 𝑈𝑛𝑜𝑚 ≤ 𝑈𝑀𝐶𝑂𝑉.𝑍𝑛1(2) ; 33 𝑘𝑉 ≤ 36
כאשר:
-ממתח הנומינלי של רשת הספקת חשמל Unom
- UMCOV.Znמתח תפעולי מרבי של מגן ברק
מתח שיורי נקוב המתקבל ,כתוצאה ממעבר זרם אימפולס חייב להיות גבוה יותר .3
ממתח שיורי מחושב.
𝑠𝑦𝑠𝑈𝑙𝑖𝑛𝑒. 33
∗ 𝑈𝑟𝑒𝑠.𝑐𝑎𝑙 ≥ 2.2 ∗ √2 ∗ = 2.2 ∗ √2 𝑉𝑘 = 59.28
√3 √3
תקין 𝑉𝑘 𝑈𝑟𝑒𝑠.𝑐𝑎𝑙 ≤ 𝑈𝑟𝑒𝑠.𝑛𝑜𝑚 ; 59.28 ≤ 242
כאשר:
מתח שיורי המחושב במערכת - 𝑙𝑎𝑐𝑈𝑟𝑒𝑠.
מתח שיורי הנומינלי הנשאר אחרי העברת זרם אימפולס - 𝑚𝑜𝑛𝑈𝑟𝑒𝑠.
כאשר:
ממתח הנומינלי של רשת הספקת חשמל - Unom
מתח נומינלי של מגן ברק - Unom.Zn
מתח תפעולי מרבי של מגן ברק חייב להיות גבוה מהמתח הנומינלי של המערכת .2
תקין 𝑉𝑘 𝑈𝑛𝑜𝑚 ≤ 𝑈𝑀𝐶𝑂𝑉.𝑍𝑛1(2) ; 6.6 𝑘𝑉 ≤ 7.2
כאשר:
-ממתח הנומינלי של רשת הספקת חשמל Unom
- UMCOV.Znמתח תפעולי מרבי של מגן ברק
מתח שיורי נקוב המתקבל ,כתוצאה ממעבר זרם אימפולס חייב להיות גבוה יותר .3
ממתח שיורי מחושב.
𝑠𝑦𝑠𝑈𝑙𝑖𝑛𝑒. 6.6
∗ 𝑈𝑟𝑒𝑠.𝑐𝑎𝑙 ≥ 2.2 ∗ √2 ∗ = 2.2 ∗ √2 𝑉𝑘 = 11.9
√3 √3
תקין 𝑉𝑘 𝑈𝑟𝑒𝑠.𝑐𝑎𝑙 ≤ 𝑈𝑟𝑒𝑠.𝑛𝑜𝑚 ; 11.9 ≤ 104
כאשר:
מתח שיורי המחושב במערכת - 𝑙𝑎𝑐𝑈𝑟𝑒𝑠.
מתח שיורי הנומינלי הנשאר אחרי העברת זרם אימפולס - 𝑚𝑜𝑛𝑈𝑟𝑒𝑠.
The 3EK7 surge arrester from Siemens - Metal oxide varistor (MOV)
https://www.eselo.lv/upload/catalog/vidspriegums/siemens_3ek7_iec_ansi_eng.pdf
Rated voltage (Ur) - An arrester fulfilling the IEC standard must withstand its
rated voltage (Ur) for 10 s after being preheated to 60 °C and subjected to energy
injection as defined in the standard. Thus, Ur shall equal at least the 10-second TOV
capability of an arrester.
Continuous operating voltage (Uc) - It is the maximum permissible r.m.s. power
frequency voltage that may be applied continuously between the arrester terminals.
Maximum system voltage (Um) - The maximum voltage between phases during normal
service.