Professional Documents
Culture Documents
Product
Catalogue
1
Index
S.No. INDEX
1 Desilter
2 Desander
3 Mud Cleaner
4 Vacuum Degasser
5 Shale Shaker
6 Mud Agitator
9 Master Bushing - Medium Duty Pin Drive & Square Drive Split
10 Casing Bushing
11 Roller Kelly Bushing - Heavy Duty Pin Drive & Square Drive
15 Casing Slips
18 Safety Clamps
25 Stabbing Guide
2
26 Wear Guide Assembly Plate & Drifts for Casing and Tubing
28 Dies for Woolley Slips, TSK Slips & Varco Power Slips
Inserts for Rotary Slips, Dies for Safety Clamp & Inserts for Cavins Tubing
29
Spider
30 Slip Inserts, Tong Dies, Iron Roughneck Dies & Holders
42 Hammer Union
45 Rotary Subs
46 Butterfly Valve
47 Ball Valves
3
DESILTER
PAN Ind. Desilter is a Hydroclone that is used to remove sand particles which have a grain size of 20 microns or
less. Hydroclones operate on the basis of centrifugal force such that the mud with smaller particles is returned
to the active system while the larger particles are discarded. The usual size of a Desilter is 6 inches and above,
however the most common size is 10 inches. PAN Ind. Desilter makes separations between 15 and 45 μm.
Characteristics
▪ Material Used: 100% Polyurethane to Make Desilter Cones Longer Life.
▪ Clamp Type for Easy Maintenance.
▪ Compact Design with Small Footprint.
▪ Flexible Fast Connection Is Available For User Assembly.
Technical Parameter
PAN Ind. Desilter
Model PAN-DL-10
Vibrating mode Elliptical
Motor type Standard Design
Power(kW)/(HP) 1 x 0.75 kW (1 HP) (one motor)
G-force(G) ≤ 8.3 (adjustable)
Total screen area(m2 )/(ft 2 ) 0.78/8.4
Screen tilt angle adjustment scope( °) Unadjustable
Pressure head(m/ft) 23/75
Capacity(m3/h)/(GPM) 227/1000
Screen type Soft edged (a whole piece of soft screen)
Screen spec (mm)/(in) 600 x 1450/24 x 57
Desilter cone spec. 4”
Number of Desilter cones 10
Separation size of Desilter cones(μm) 15~44
Noise (dB) <85
Dimensions (mm)/(in) 1455 x 2426 x 1774/57 x 96 x 70
Weight (kg)/(lbs) 1050/2315
IN-Line Desilter
PAN Ind. Desilter
Model PAN-DL-20
Inlet Size (In Inch) 8”
Outlet Size (In Inch) 8”
Size of sand discharge port (In Inch) 8”
Cone Spec. (In Inch) 4”
Number of Cones 20
Separation size (μm) 10-74
Capacity of Single cone (GPM) 50-80
Pressure head (m)/Pressure head (ft) 75
4
DESANDER
PAN Ind. Desander is a hydroclone that is used to remove sand and silt from drilling fluids in an Oil Field
drilling rig. Hydroclones operate on the basis of centrifugal force such that the mud with smaller particles
is returned to the active system while the larger particles are discarded. PAN Ind. Desander removes
those abrasive solids from the drilling mud which cannot be removed by shakers. We mainly used 8 "and
10" cones Desander to separate solid-phase particle size 45-75 in the drilling fluids
Characteristics
▪ Material Used: 100% Polyurethane to Make Desilter Cones Longer Life.
▪ Clamp Type for Easy Maintenance.
▪ Compact Design with Small Footprint.
▪ Flexible Fast Connection Is Available For User Assembly.
Technical Parameter
PAN Ind. Desander
Model PAN-DS-2
Vibrating mode Elliptical
Motor type Standard Design
Power(kW)/(HP) 1 x 0.75 kW (1 HP) (one motor)
G-force(G) ≤ 8.3 (adjustable)
Total screen area(m2 )/(ft 2 ) 0.78/8.4
Screen tilt angle adjustment scope( °) Unadjustable
Pressure head(m/ft) 23/75
Capacity(m3/h)/(GPM) 227/1000
Screen type Soft edged (a whole piece of soft screen)
Screen spec (mm)/(in) 600 x 1450/24 x 57
Desilter cone spec. 10”
Number of Desilter cones 2
Separation size of Desilter cones(μm) 44~74
Noise (dB) <85
Dimensions (mm)/(in) 1455 x 1774 x 2100/57 x 70 x 83
Weight (kg)/(lbs) 1240/2734
Vertical Desander
PAN Ind. Desilter
Model PAN-DS-3
Inlet Size (In Inch) 8”
Outlet Size (In Inch) 10”
Size of sand discharge port (In Inch) 10”
Cone Spec. (In Inch) 10”
Number of Cones 3
Separation size (μm) 40-100
Capacity of Single cone (GPM) 500
Pressure head (m)/Pressure head (ft) 75
5
MUD CLEANER
PAN Ind. mud cleaner is a combination of Desander and Desilter mounted over a shaker with a fine mesh
screen. A mud is fed to the inlet of the hydrocyclone (Desander / Desilter) to separate particles and the
underflow passes to the fine screen mesh where in particles are discarded and thrown away.
Characteristics
▪ Polyurethane material, high-chromium cast iron or ceramic to make Desander and Desilter cones.
▪ Desander cones can be installed between one and three 10" Desander cones, each cone can process
500 GPM and makes a separation between 45 and 75 μm.
▪ Desilter cones can be installed between eight and twenty 4" or 5" Desilter cones, each cone can
process 80 GPM, and makes a separation between 15 and 45 μm.
▪ Mechanical Deck is adjustable during operation.
▪ Hook-strip shaker screen for fast screens changing with screens.
▪ Desilter assembly can be arranged as in-line or round type according to customer’s requirements.
Technical Parameter
PAN Ind. Mud Cleaner
Model PAN-MC-210 PAN-MC-320
Vibrating mode Linear Motion Linear Motion
Power(kW)/(HP) 2 x 1.72 kW (2 x 2 HP) (Italy Oli) 2 x 1.72 kW (2 x 2 HP) (Italy Oli)
G-force ≤ 7.4 (adjustable) 7.1 (6.5~7.5 adjustable)
Shaker Screen (m2)/(ft2) 2.2/24 2.7/29
Deck Adjustment( °) -1~+5 -1~+5
Pressure head(m/ft) 23/75 23/75
Screen Category Hook Strip Frame/Pre-tensioned
Screen mesh Size (mm)/(inch) 700 x 1050/27.5 x 41 585 x 1165/23 x 46
Desander Cyclone Diameter 10” 10”
Desander Cyclone Number 2 3
Desander Separation size (μm) 44~74 44~74
Desilter Cyclone Diameter 4” 4”
Desilter Cyclone Number 10 10
Desilter Separation size (μm) 15~44 15~44
Noise (dB) <85 <85
L x W x H (mm) (inch) 2448 x 2943 x 2508/96 x 116 x 98 3277 x 2180 x 3072/129 x 86 x 121
Weight (kg)/(lbs) 2380/5248 3450/7607
6
VACUUM DEGASSER
PAN Ind. Vacuum Degasser eliminates the gas from the mud. During the drilling process, the gas
contained in drilling fluids from wells affects the mud property, bring hidden danger and shorten the
service life of some equipment. So, it is necessary to install a vacuum degasser to eliminate such type of
gas from the mud.
Characteristics
▪ Compact design and small footprint
▪ Self-priming device enables it to pump drilling fluids without a centrifugal pump.
▪ It can also serve as a high-power mud agitator
▪ Corrosion is eliminated and cost of repair and maintenance is reduced.
Technical Parameter
PAN Ind. Vacuum Degasser
Model PAN-VD-240 PAN-VD-270 PAN-VD-300 PAN-VD-360
Max Capacity (m3/h) 240 270 300 360
Vacuum Degree (mmHg) 300-340 400-450 400-450 400-550
Transmission Ratio 1.67 1.68 1.68 1.72
Main Motor Power (kW) – 4 class 15 22 30 37
Vacuum Pump Power (kW) – 4 class 2.2 kW – 4 Grade 2.2 kW – 4 Grade 4 kW – 4 Grade 5.5 kW – 4 Grade
Rotating Speed (rpm) 876 870 880 860
Displacement (m3/h) 28 48 90 180
Proper mud weight (g/cm3) ≤2 ≤2 ≤2.5 ≤2.5
Degassing Efficiency (%) ≥95 ≥95 ≥95 ≥95
Weight (Kg) 1200 1450 1960 2510
External Dimension (inch) 69 x 42 x 61 77 x 43 x 67 89 x 53 x 68 94 x 59 x 75
7
SHALE SHAKER
PAN Ind. shale shaker is solids control equipment in drilling purification system. It can remove cuttings
above 75 μm brought from the drilling well to leave the liquid with smaller particles into the tanks below,
which will flow into next grade solids control equipment for further treatment.
PAN Ind. shale shakers are the equipment with welded structure. Vibration motor & screen plate base
are installed into screen basket with special parts. Screen basket is fixed on the adjustment beam. At
each of the four vertexes of the screen basket put a vibration damping spring, which can prevent the
adjoining parts and devices from being affected by the vibration. Linear Motion Shale Shaker of PAN Ind.
is especially effective while drilling top-hole sections where heavy and high-volume solids are usually
encountered. In these intervals, shakers may generate powerful G-forces and its effective vibrating
motion can quickly remove the dense solids from screens and particles from wells.
Characteristics
▪ Hi-speed conveyance of cuttings.
▪ Higher processing capacity.
▪ Able to process heavier solids loads.
▪ Enhances cuttings processing volume.
▪ Single side shale shaker screens tension system to easily change the screens.
▪ Shale shaker feeder can be weir feeder or box feeder.
Technical Parameter
PAN Ind. Linear Motion Shale Shaker
Model PAN-LMSS-301 PAN-LMSS-302 PAN-LMSS-401 PAN-LMSS-303
Vibration Mode (kW)/(hp) Linear Motion Linear Motion Linear Motion Linear Motion
G-Force ≤7.4 (Adjustable) ≤7.0 (Adjustable) 7.1 (6.5~7.5 Adjustable) 7.0 (6.6~7.4 Adjustable)
Shaker Screen (m2)/(ft2) 2.2 / 24 2.7 / 29 2.7 / 29 2.0 / 21.5
Deck Adjustment (°) -1~+5 -1~+5 -1~+5 -1~+5
Capacity (GPM) 500~600 600~750 600~750 500~600
Screen Type Hook Strip Hook Strip Hook Strip Frame/Pre-tensioned
Screen Dimension (inch) 27.5 x 41 33 x 42.5 23 x 46 23 x 46
Screen No. 03 03 04 03
Noise (dB) <85 <85 <85 <85
Weir Height (mm)/(inch) 882 / 35 882 / 35 780 / 30 940 / 37
L x W x H (inch) 111 x 72 x 64 125 x 74 x 64 118 x 73 x 60 92.5 x 69 x 65
Weight (kg) 1815 1930 1925 1680
8
MUD AGITATOR
PAN Ind. mud agitator is part of the drilling fluids solids control equipment, which is mainly used to
agitate and mix the drilling mud to prevent solids particles from depositing in the circulating tank and to
stabilize the performance of drilling fluids. The motor and speed reducer, speed reducer and impeller
shaft are connected by steel coupling.
Technical Parameter
PAN Ind. Mud Agitator
Model PAN-MA-400 PAN-MA-550 PAN-MA-750 PAN-MA-1100 PAN-MA-1500 PAN-MA-2200
Motor
Power 4 5.5 7.5 11 15 22
(kW)
Motor 50 Hz 1430 1450 1450 1460 1460 1470
Rated
Speed 60 Hz 1716 1740 1740 1752 1752 1764
Impeller 50 Hz 72 72 72 73 73 73
Speed
(rpm) 60 Hz 69 69 69 70 70 70
Impeller Double 500 650/600 700/650 800/700 850/750 1000/900
Diameter
(mm) Single 500 650/700 800 850 900
9
MASTER BUSHING HINGED TYPE PIN DRIVE
PAN-MB-3750 MODEL for NATIONAL, EMSCO, OILWELL & All Other Rotary Tables
PAN Ind. manufactures Master Bushing 37½” hinged type Pin Drive suitable for 37½” to 49½” Rotary table for
offshore & onshore drilling operation to provide rotational force to drill string. It is equipped with standard Bowl
No. 3 & optional Bowl No. 1 & 2 with taper as per API Specifications to accommodate 2-3/8” to 13-3/8” O.D of
Drill Pipes, Drill collars & tubular to handle up to the load of 500 tons. Torque Rating: 32362 Nm at 300 RPM.
The PAN-MB is incorporated with Bowl lock assembly that lock the Bowls. It is designed in hinged type that can
be removed easily from Rotary Table; facilitate to pass large Diameter Bits and Tubular directly through Rotary
Table.
Master Bushing
Model PAN-MB-3750 Hinge Pin Removable
10
Master Bushing Accessories:
▪ Lifting Sling: Chain type with four hooks for Master Bushing & Two Hook for Bowl for lifting purpose.
▪ Bit Breaker Adapter Plate: To accommodate different sizes of Bit Breakers for Makeup –Breakup of Bits.
▪ Insert Bowls: API Insert Bowl No 1, 2 & 3 to handle tubular.
S. DESCRIPTION Req. Qty Identical Varco PAN PART No. PAN PART No. PAN PART No.
No. Per Set PART No. For National For Oil Well For EMSCO
Master Bushing Bare body segment
1 2 no -- P35710 P35710-SQ P35710-E
only
2 Hinge Pin-Removable (with handle) 1 no 6604 P35711 P35711-SQ P35711-E
3 Hinge Pin Retainer 1 no. 6606 P35711-A P35711-A-SQ P35711-A-E
4 Hinge Pin-Stationary (with retainer) 1 no 6605 P35712 P35712-SQ P35712-E
5 Bowl lock assembly 2 no -- P35714 P35714-SQ P35714-E
6 Eccentric Pin 1014 P35714-A P35714-A-SQ P35714-A-E
7 Eccentric Pin Lock 1016 P35714-B P35714-B-SQ P35714-B-E
8 Eccentric Pin Retainer 50106-22 P35714-C P35714-C-SQ P35714-C-E
9 Drive Hole Bushing 4 no 3699 P35715 P35715-SQ P35715-E
Other Components to be supplied with set
10 Lifting Sling 1 no 6699 P35716 P35716-SQ P35716-E
11 Bit Breaker Adapter Plate 1 no 1816 P35717 P35717-SQ P35717-E
12 Insert Bowl No: 1 11-3/4" to 13-3/8" 6610 P35751 P35751-SQ P35751-E
13 Insert Bowl No: 2 9-5/8" to 10-3/4" any one 6609 P35752 P35752-SQ P35752-E
14 Insert Bowl No: 3 2-3/8” to 8-5/8" 6608 P35753 P35753-SQ P35753-E
11
MASTER BUSHING SOLID BODY PIN DRIVE
PAN Ind. manufactures Master Bushing Pin Drive Solid Body suitable
for 27½”and 20½” API Rotary Table, it is equipped with standard Bowl
No. 3 and optional Bowl No. 1 & 2, to accommodate tubular from 2-3/8”
to 13-3/8” with the help Insert Bowls, having a maximum Handling
capacity of 500 Tons string load. Torque Rating: 27459 Nm at 300 RPM.
The PAN-MB is incorporated with Bowl lock assembly that lock the
Bowls, MB have locking type drive hole bushes system to lock the Kelly
Bushing and Power Slip Lifter. The Pin Drive Master Bushing allows the
Kelly Bushing to fit on the top of the master bushing and makes
possible to use extended Split Bowls while the Kelly Bushing is in
operation.
S.No. DESCRIPTION Req. Qty. Per Part No. For PAN- PART No. For
Set MB 2750 PS PAN-MB 2050 PS
1. Master Bushing Bare body only One P25751-PS P25051-PS
2. Bowl Lock Assy. Two P25752-PS P25052-PS
3. Drive Hole Bushing Four P25753-PS P25053-PS
4. Lifting Sling One P25754-PS P25054-PS
5. Bit Breaker Plate One P25755-PS P25055-PS
Insert Bowl No.1 For 11.3/4” To 13.3/8” Tubular P25756-PS --
6. Insert Bowl No.2 For 9.5/8” To 10.3/4” Tubular any one P25757-PS P25057-PS
Insert Bowl No.3 For 2.3/8” To 8.5/8” Tubular P25758-PS P25058-PS
12
MASTER BUSHING SPLIT TYPE PIN DRIVE WITH BOWL SUITABLE FOR 27½” ROTARY
TABLE AND ITS PARTS LIST
Master Bushing Split type accommodate API Insert Bowl No. 1, 2 &
3 to handle tubular size from 2-3/8” to 13-3/8”, Master Bushing
having 4 Nos of drive hole bushes to lock the Kelly Bushing with the
help of eccentric Drive Pin and Bowl lock assembly to lock the Bowl
in the split Bushing. Lifting Sling 2 Hook type to lift Master Bushing
and Bowls & Bit Breaker Adapter plate are provided.
SPLIT BODY SQUARE DRIVE MASTER BUSHING SUITABLE FOR 27-½” ROTARY TABLE
Having Itself Taper of Bowl No. 3 Along With Lifting Sling
S. DESCRIPTION Req. Qty. Per PART No. FOR PAN-MB 2750 PART No. FOR PAN-MB
No. Set SSP 1750 SSP
1. Master Bushing Bare Body Two P25751-SSP P15751-SSP
13
MASTER BUSHING MEDIUM DUTY PIN DRIVE & SQUARE DRIVE SPLIT
S.No. DESCRIPTION Req. Qty. Per Part No. For PAN- Part No. For PAN- PART No. FOR PAN-
Set MB 2750 PSP MB 2050 PSP MB 1750 PSP
1. Master Bushing Bare Body Two P25751-PSP P25051-PSP P15751-PSP
2. Drive Hole Bushing Four P25753-PSP P25053-PSP –
3. Lifting Sling One P25754-PSP P25054-PSP P15754-PSP
4. Bit Breaker Adapter Plate One P25755-PSP P25055-PSP P15755-PSP
14
CASING BUSHING
PAN Ind. manufactures different sizes of Casing Bushing in Models Solid & Split type for inserting tubular directly
into Rotary Tables for a range of 17½” to 37½” and accommodates casing size from 2-3/8” to 30” in a diameter with
the help of required size of Insert Bowls. Insert Bowls available in different sizes to lower the required sizes of Casing
Pipe.
It is easily fitted into the Rotary Table at the time of lowering the Casing Pipes in well hole & it helps to make casing in
centre of the hole during Drilling Operations.
15
ROLLER KELLY BUSHINGS HEAVY DUTY PIN DRIVE & SQUARE DRIVE
PAN IND. manufacture Pin Drive Kelly Bushing for onshore & offshore
Drilling Operations, available in two sizes PAN-KB Model 27 PDHD,
20 PDHD, suitable for a range of 20½” to 49½” Rotary Table having
23” and 25-3/4” Dia Pin Centre, works as connecting equipment
between Rotary Table & Kelly. This unit is used for Heavy Duty
Drilling Operation & high torque conditions at the time of Drilling
Operations & handles Kelly sizes from 3” to 6”Square or
Hexagonal. Suitable up to torque load: 32362 N-m at 300 RPM
16
KELLY BUSHING 27, 20 PDHD & 27 SDHD COMPLETE SET LIST:
HEAVY DUTY ROLLER KELLY BUSHINGS Roller Assembly Complete* Part
Kelly No.
Size/type 27 PDHD COMPLETE KELLY BUSHING 20 PDHD SDHD
PAN Identical
Identical COMPLETE KELLY COMPLETE
PAN- PART BUSHING PART No. VARCO PART
VARCO PART KELLY BUSHING
No. No. No.
3" Hex P25701-P 3650-30 P25001-P P25701-S P25101 3667
3½" Hex P25702-P 3650-35 P25002-P P25702-S P25102 3668
4¼" Hex P25703-P 3650-42 P25003-P P25703-S P25103 3669
5¼" Hex P25704-P 3650-52 P25004-P P25704-S P25104 3672
6" Hex P25705-P 3650-60 P25005-P P25705-S P25105 3673
2½: Sq. P25722-P - - - - -
3" Sq. P25706-P 3651-30 P25006-P P25706-S P25106 3660
3½" Sq. P25721-P 3651-35 P25011-P P25711-S P25110 3661
4¼" Sq. P25707-P 3651-42 P25007-P P25707-S P25107 3662
5¼" Sq. P25708-P 3651-52 P25008-P P25708-S P25108 3665
6" Sq. P25709-P 3651-60 P25009-P P25709-S P25109 3666
Roller Assembly consists of Flat/V-roller (One), Roller Pin (One) Bearing (One), and Thrust Washer (Two)
KELLY BUSHING SPARE PARTS LIST:
Item 27 PDHD
DESCRIPTION PAN- PART 20 PDHD SDHD
No. VARCO PART
No. No.
1. Kelly Bushing Body assembly less roller assembly P25710-P 3653 P25010-P P25710-S
2. Hold down bolt P25711 13501 P25711 P25711
3. Hold down bolt lock screw P25711-A 50110-8-S
4. Nut for hold down bolt P25712 1208 P25712 P25712
5. Lock washer for nut P25713 51110-C P25713 P25713
6. Drive pin with washer P25714 1605 P25714-S --
7. Wrench P25715 1210 P25715 P25715
8. Wiper assembly P25716 -- P25716 P25716
9. Wiper Retainer Plate P25716-B 1321
10. Wiper Retainer Plate Screw P25716-C 50008-10-S
11. Roller Pin P25717 3609 P25717 P25717
12. Roller Bearing P25718 1312 P25718 P25718
13. Sleeve Bush P25719 1326 P25719 P25719
14. Thrust Washer P25720 3618 P25720 P25720
17
KELLY BUSHING 17 PDMD, 17 SDMD & 17 SDHD COMPLETE SET LIST:
17 PDMD 17 SDMD 17 PAN-
KELLY INDIVIDUAL ROLLER FOR HEX
COMPLETE COMPLETE SDHD ROLLER
SIZE / KELLY KELLY BUSH COMPLETE ASSEMBLY V FLAT
TYPE BUSHING KELLY BUSH ROLLER ROLLER
2½" SQ P15701-P P15701-S P15701-SH P15721 P15729 P15737
3" SQ P15702-P P15702-S P15702-SH P15722 P15730 P15738
3½" SQ P15703-P P15703-S P15703-SH P15723 P15731 P15739
4¼" SQ P15704-P P15704-S P15704-SH P15724 P15732 P15740
5¼" SQ P15705-P P15705-S P15705-SH P15725 P15733 P15741
3" HEX P15706-P P15706-S P15706-SH P15726 P15734 P15742
3½" HEX P15707-P P15707-S P15707-SH P15727 P15735 P15743
4¼" HEX P15708-P P15708-S P15708-SH P15728 P15736 P15744
18
ROTARY SLIPS / DRILL PIPE SLIPS
PAN Model RSST, RSMD & RSLG
PAN Ind. manufactures Rotary Slips/ Drill Pipe slips to handle tubular
size 2-3/8”to 7” to be used in API Insert Bowl No 3 having an API
taper of 4 inch per feet on the diameter. Having various gripping
length i.e. Short, Medium & Long, having elastromer gripes on
handles. Suitable to 100 Tons to 250 Tons Load capacities.
PAN manufactures Rotary Slips in wedged shape and designed in three
body segments that are hinged together, forming a near circle around
the Drill Pipe, to provide maximum handling capacity, high strength
with minimum weight to ease the handling. The PAN design provides
for full distribution of load throughout the length of the slips which
helps in preventing damage of Drill Pipes. The Inserts are changed at
Rig sites in a very short time by simply removing the locking
arrangement and retainers. Rotary Slips are also available with flexible
handles (on demand).
19
PAN-RS - RSMD MEDIUM ROTARY SLIPS COMPLETE SET LIST:
Slip Body Sizes (Inches) 3-1/2 4-1/2
API Pipe Sizes (OD Inches) 2.3/8 2.7/8 3.1/2 3.1/2 4 4.1/2
Slip Complete with insert : Part No. 20121 20122 20123 20124 20125 20126
Slip Complete with Insert (Weight) 88 kg. 85 kg. 82 kg. 94 kg. 91 kg. 86 kg.
Insert Part No. 20160-30 20161-30 20162-30 20163-45 20164-45 20165-45
Slip Body Sizes (Inches) 5 5-1/2
API Pipe Sizes (OD Inches) 4 4.1/2 5 4.1/2 5 5.1/2
Slip Complete W/insert : Part No. 20127 20128 20129 20130 20131 20132
Slip Complete with Insert (Weight) 92.5 kg. 89 kg. 84 kg. 91 kg. 84 kg. 82.5 kg.
Insert Part No. 20168-45 20166-45 20167-45 20168-45 20169-45 20170-45
20
DRILL COLLAR SLIPS
PAN manufactures Drill Collar Slips in three sizes Short, Regular &
Long covering all popular Drill Collar sizes in use i.e. from 3” to
14”O.D.Drill Collar Slips, Provided with elastromer grips on handles.
PAN Drill Collar Slips are having multi segment design to give a full
wrap around the diameter of Drill Collars having an API Taper of 4
inch per feet on the diameter fitted with Circular Buttons and up right
handles, have extra back support to ensure sufficient strength &
support to the inserts of various sizes. It is general practice to use
Safety Clamps while handling Drill Collars so the top surface of these
slips are designed flat to ensure smooth fitting of the safety clamp.
21
DESCRIPTION PAN-DCS-S PAN-DCS-R PAN-DCS-L
Spare Parts List Part No. Part No. Part No.
Segment - Right End 20212 20237 20241
Segment-Left End 20213 20238 20242
Segment-Intermediate 20214 20239 20243
Hinge Pin with Cotter Pin 20215 20240 20244
Handle Pin with Washer & Cotter Pin 20216 20216 20216
Handle for Right & Left End Segment 20217 20217 20217
Handle for Intermediate Segments 20218 20218 20218
Retaining Cotter Pin 20235 20235 20235
Retaining Screw with Lock Washer 20236 20236 20236
22
CASING SLIPS
PAN Ind. Casing Slips are made out of best quality of alloy steel having
an API taper of 4 inch per feet on the diameter, fitted with circular
buttons and with 3 to 4 Nos of upright handles. Multi Segment
design of slips ensures self centering of casings in the rotary table.
Slips insert are so designed that these hold the casing pipe firmly
with-out causing any damage. The advantage of multi segment
design lies in the fact that by simply increasing or decreasing the
number of slip segments, casing sizes from 5 inch to 30 inch OD
can be handled with ease while dressing the slip with appropriate
size of insert.
23
Casing Slip Spare Parts List:
DESCRIPTION CMS-XL Part No.
Segment - Right End 20316
Segment-Left End 20317
Segment-Intermediate 20318
Hinge Pin with Cotter Pin 20319
Handle Pin with Washer & Cotter Pin 20320
Handle for Right & Left End Segment 20321
Handle for Intermediate Segments 20322
Retaining Screw with Lock Washer 20323
24
PNEUMATIC POWER SLIPS
PAN Ind. manufactured Pneumatic Power Slip is a fully automatic,
remote controlled, air operated system for the setting and releasing
of drill pipe slips for 3-1/2" to 5-1/2" drill pipe. The PPS can
accommodate 6-5/8" drill pipe, but only as a tripping tool.
The PPS eliminates the difficult and sometimes dangerous job of
hand setting and lifting of Drill Pipe Slips. The Pneumatic Power Slips
can be controlled by either a hand or foot operated remote control
valve. The Power slips are set by gravity and released by applied air
pressure. The Power Slips is designed to fit into 27-1/2" and 37-1/2"
to 49-1/2" Rotary Tables equipped with Pin Drive Master Bushings.
PAN manufactured Pneumatic Power Slips are non Rotating
equipment.
Slip for Power Slip 4-1/2" Slip Body for 3-1/2" to 4-1/2" drill pipe
Slip for Power Slip 5-1/2" Slip Body for 4-1/2" to 5-1/2" drill pipe
Slip for Power Slip 6-5/8" Slip Body for 6-5/8" drill pipe only
25
POWER SLIP LIFTER (PNEUMATIC OR HYDRAULIC)
Lifter for Rotary Slip, Drill Collar Slip & Casing Slip
Power Lifter for Rotary Slip: It accommodates Rotary Slips in the range of 2-3/8” to 8-5/8”.
Power Slip Model Part No. Rotary Table Size Master Bushing Type Pipe Size handling
capacity
P-PSL-1750 P RT-17-1/2” Pin Drive 2-3/8” to 8-5/8”
P-PSL-2050 P RT- 20-1/2” Pin Drive Solid Body 2-3/8” to 13-3/8”
P-PSL-2050 P RT- 20-1/2” Pin Drive Split Body 2-3/8” to 8-3/8”
P-PSL-2750 P RT- 27-1/2” Pin Drive Solid Body 2-3/8” to 13-3/8”
P-PSL-2750 S RT- 27-1/2” Square Drive Body 2-3/8” to 13-3/8”
P-PSL-2750 P RT- 37-1/2” Pin Drive Hinged Type 2-3/8” to 13-3/8”
Power Lifter for Drill Collar Slip: It accommodates Drill Collar Slip in the range of 3” to 14”.
Power Slip Model Part No. Rotary Table Size Master Bushing Type Pipe Size handling
capacity
P-PSL-1750 P RT-17-1/2” Pin Drive 3” to 8-5/8”
P-PSL-2050 P RT- 20-1/2” Pin Drive Solid Body 3” to 14”
P-PSL-2050 P RT- 20-1/2” Pin Drive Split Body 3” to 8-5/8”
P-PSL-2750 P RT- 27-1/2” Pin Drive Solid Body 2-3/8” to 13-3/8”
P-PSL-2750 P RT- 37-1/2” Pin Drive Hinged Type 2-3/8” to 13-3/8”
P-PSL-1750 P RT-17-1/2” Pin Drive 3” to 8-5/8”
26
Power Slip Lifter for Casing Slip: It accommodates Casing Slips in the range of 5” to 30”.
Power Slip Model Additional Power Slip Rotary Table Size Casing Bushing Type Pipe Size
Part No. Fixtures to be fixed Handling Capacity
on Casing Bushing
P-PSL-2700 – RT- 27-1/2” CB 20” Split type 5” to 20”
-- RT- 37-1/2” CB 20” Split type 5” to 20”
Base with Rings for 24” RT- 37-1/2” CB 24” Split type 24”
P-PSL-3700
Base with Rings for 26” RT- 37-1/2” CB 26” Split type 26”
Base with Rings for 30” RT- 37-1/2” CB 30” Split type 30”
1. Cylinder P2791 01
2. Cylinder Base Hinge P2792 01
3. Cylinder Rod Hinge P2793 01
4. Reducing Nipple P2794 02
5. Pressure Control Valve P2795 02
6. Hose Pipe Assembly ( 26”Length) P2796 01
7. Hose Pipe Assembly ( 18”Length) P2797 01
8. Hose Joint Connector P2798 02
9. Nut P2799 02
10. Hose Pipe Assembly ( Power Slip to Foot Paddle Valve) P2756 02
11. Connector P2757 03
12. Foot Paddle Valve P2758 01
27
SPARE PART LIST OF AIR OPERATED POWER SLIP
S. No. Part Name PAN Part No. Qty.
1. Base Plate P2761 01
2. JIB P2762 01
3. Hinge Link P2763 01
4. Retaining Link P2764 01
5. Pin-1 (Base & JIB Mounting) P2765 01
6. Pin-2 (Hinge link to Retaining Link Mounting) P2766 02
7. Pin-3 (Hinge Link to Cylinder Eye Rod Mounting) P2767 01
8. Pin-4 (JIB to Hinge link Mounting) P2768 01
9. Pin ( Slip Fastening Link Mounting ) P2769 01
10. Splint Pin ( Slip Fastening Link Mounting Pin Locking) P2770 01
11. Locking Plate ( Retaining Link Pin Locking) P2771 05
12. Screw P2772 14
13. Washer P2773 14
14. Screw ( Cylinder Stroke Adjustment) P2774 01
15. Nut P2775 01
16. Slip Fastening Link (Short) P2776 01
17. Pin ( Slip Fastening Link to Rotary Slip Mounting) P2777 01
18. Nut ( Ref. S.No.17) P2778 01
19. Quick Lock Pin Assembly P2779 04
20. Instruction Plate P2780 01
21. Pneumatic Cylinder Assembly P2781 01
22. Protection Plate Assembly P2782 06
23. Pin ( Protection Plate Mounting) P2783 04
24. Bushing P2784 12
25. Nut P2785 04
26. Washer with Tap P2786 12
27. Screw P2787 12
28. Shackle P2788 06
29. Spring P2789 02
30. Control Valve Assembly P2790 01
PAN will provide modified Rotary Slips (If ordered along with PSL) or will provide drawings for modifications so
that it can be done at your site.
28
SAFETY CLAMPS
DESCRIPTION PANSC-R
10½” - 11½” 11½” - 12½” 12½” - 13.5/8” 13.5/8” - 14.3/4” 14.3/4” - 15.7/8”
P/N : SC Complete Set P12508 P12509 P12510 P12511 P12512
Weight in Kg. 55 58.5 62 66 69.9
Total Links 12 13 14 15 16
Nos. of Gripping Dies 13 14 15 16 17
DESCRIPTION PANSC-XL
22.5/8” - 23.3/4” - 24.7/8” - 26” - 29.3/8” -
32” 36”
23.3/4” 24.7/8” 26” 27.1/8” 30½”
P/N : SC Complete Set P12519 P12520 P12521 P12522 P12523 P12524 P12525
Weight in Kg. 100 103.5 107 110.5 152.5 181 185
Total Links 22 23 24 25 28 31 35
Nos. of Gripping Dies 23 24 25 26 29 32 36
29
SAFETY CLAMPS HYDRAULIC
30
“T” TYPE SAFETY CLAMP
PAN Ind. offers safety clamps for tubing (T) and casing
(C). Multipurpose (MP) safety clamps are adjustable to a variety of
tubular. Manual clamps are equipped with screw and nut combination.
The nut secures the clamp around the pipe and should be tightened
with the supplied nut wrench. The clamp grips uniformly by design.
The individual links give the clamp flexibility to wrap around the pipe
and the inserts are spring loaded.
31
PAN Ind. MUD BUCKET
MUD BUCKET MANUAL TYPE
PAN Ind. Manufactures Mud Buckets are made in Three models: P-MG-3’,
P-MG-6’ and P-MG-6’L. Our mud guards are cost effective as it saves the
loss of expensive drilling fluid and reduces the labour for rig floor wash as
well as eliminates the chances of slipping accidents due to slippery rig
floors. The MG-6’ is 6’ x 10-¾” and can handle drill pipe sizes from 2-3/8” to
5½”. The MG- 6’L is 6’ x 16”, it’s larger cavity is designed for drill pipe sizes
from 2-3/8” to 6-5/8” and can handle larger volumes of line fluids. Both
models can be supplied with neoprene or nitrile seals.
32
S. NO. PART NAME Part No QTY
01 Main Body P-MG6P-01 –
02 Handle P-MG6P-02 02 NOS.
Top & Bottom Pipe Insert Seal (nitrile Rubber) Size is available from 2-3/8” to
03 P-MG6P-03 A TO H 04 NOS.
6-5/8”
04 Door Seal (rubber) P-MG6P-04 04 NOS.
05 Lifting Hook P-MG6P-05 02 NOS.
06 Right Side Cylinder End Mounting Bracket P-MG6P-06 03 NOS.
07 Pneumatic Cylinder With Both Side End Mounting P-MG6P-07 03 NOS.
08 Safety Guard P-MG6P-08 01 NOS.
09 Left Side Cylinder end Mounting Bracket P-MG6P-09 03 NOS.
10 Filter Regulator Lubricant Combine Unit P-MG6P-10 01 NOS.
11 Liver Type Rotary Valve P-MG6P-11 01 NOS.
12 Bottom Leg (for Stand) P-MG6P-12 04 NOS.
13 Mud Exhaust Pipe 4” /6” P-MG6P-13 01 NOS.
14 Quick Opening & Closing Hose Clamp P-MG6P-14 01 NOS.
15 Pneumatic Hose Air In P-MG6P-15 01 NOS.
16 Pneumatic Hose Air Out P-MG6P-16 01 NOS.
17 Manifold P-MG6P-17 3 LENGTH
18 Pneumatic Hose Air Out P-MG6P-18 3 LENGTH
19 Manifold P-MG6P-19 02 NOS.
20 Air Supply Hose Complete With Qd Connection P-MG6P-20 50 FEET LONG
33
BIT BREAKERS & BIT GAUGE
PAN Ind. Manufactures Bit Breakers & Bit Gauge as Oil Field
required.
PAN Ind. Bit Breakers are Heavy Plate that fits in the Rotary
Table and holds the drill bits while it is being made up in or
broken out of the drill stem.
PAN Ind. Bit Breakers are durable and have high performance.
PAN Ind. manufactures all sizes of Bit Breakers with quality
standard.
34
Bit Gauges for TCR Bit
S. No. BIT SIZE PAN-Part No. S. No. BIT SIZE PAN-Part No.
1. 4.1/8” P-BG-1501 21. 10½” P-BG-1509-B
2. 4¼” P-BG-1501-B 22. 10.5/8” P-BG-1510
3. 4¾” P-BG-1501-A 23. 11” P-BG-1510-A
4. 5.5/8” P-BG-1502 24. 11-3/4” P-BG-1511
5. 5.7/8” P-BG-1502-A 25. 12¼” P-BG-1511-A
6. 6” P-BG-1503 26. 13¾” P-BG-1512
7. 6.1/8” P-BG-1504-B 27. 14¾” P-BG-1513
8. 6¼” P-BG-1503-A 28. 15” P-BG-1513-A
9. 6½” P-BG-1504 29. 16” P-BG-1514
10. 6¾” P-BG-1504-A 30. 17½” P-BG-1515
11. 7.3/8” P-BG-1505 31. 18½” P-BG-1516
12. 7½” P-BG-1505-A 32. 20” P-BG-1517
13. 8.½” P-BG-1506 33. 22” P-BG-1518
14. 8.5/8” P-BG-1506-A 34. 23” P-BG-1519
15. 8¾” P-BG-1507 35. 24” P-BG-1520
16. 8.3/8” P-BG-1507-B 36. 26” P-BG-1521
17. 9” P-BG-1507-A 37. 28” P-BG-1522
18. 9½” P-BG-1508 38. 30” P-BG-1522-A
19. 9.5/8” P-BG-1509 39. 34” P-BG-1524
20. 9.7/8” P-BG-1509-A 40. 36” P-BG-1523
35
STABBING GUIDE
Stabbing Guides: Model PAN-SG: The Stabbing Guide is for Tubing,
Casing & Drill Pipe having spring loaded to closed position by a torsion
spring and provided with a pair of hand grip levers to facilitate
opening, placement, and removal.
36
Stabbing Guide for Tubular and casing
Applicable diameter for Tubular Applicable diameter for Tubular
PAN - SG Model PAN - SG Model
and Casing (In.) and Casing (In.)
PAN - SGT 2-3/8” 2-3/8” Tubing PAN - SGC 7-5/8” 7-5/8” Casing
PAN - SGT 2-7/8” 2-7/8” Tubing PAN - SGC 8-5/8” 8-5/8” Casing
PAN - SGT 3-1/2” 3-1/2” Tubing PAN - SGC 9-5/8” 9-5/8” Casing
PAN - SGT 4” 4” Tubing PAN - SGC 10-3/4” 10-3/4” Casing
PAN - SGT 4-1/2” 4-1/2” Tubing PAN - SGC 11-3/4” 11-3/4” Casing
PAN - SGC 4-1/2” 4-1/2” Casing PAN - SGC 13-3/8” 13-3/8” Casing
PAN - SGC 5” 5” Casing PAN - SGC 13-5/8” 13-5/8” Casing
PAN - SGC 5-1/2” 5-1/2” Casing PAN - SGC 14” 14” Casing
PAN - SGC 6” 6” Casing PAN - SGC 16” 16” Casing
PAN - SGC 6-5/8” 6-5/8” Casing PAN - SGC 18-5/8” 18-5/8” Casing
PAN - SGC 7” 7” Casing PAN - SGC 20” 20” Casing
37
WEAR GUIDE PLATE ASSEMBLY
PAN Ind. manufactures Casing & Tubing drifts as per API 5CT
Specifications. Drifts are available in Steel, Aluminium, Teflon and
Nylon in size ranging from 2-3/8”-20”.
Drifts are used for testing roundness of Casing & Tubing; making
certain there are no Kinks, bends or flat places in the pipe. Drifts are
used to ensure that the Drill pipes are of proper diameter throughout
to run downhole tools. PAN can manufacture drifts as per customer
specifications when requested.
38
TONG DIES & SLIP INSERTS
While running in or pulling out tubular at oil rigs the joints (tool joints)
are tightened or loosened with the help of manual tongs or power
tongs.
Dies are the principal element in the manual tongs and power tongs
which carry out the function of gripping the tool joints, before torque
application. (Rollers or chain are also used for gripping of tubular while
using pipe spinners)
PAN Ind. manufactures tong dies out of best quality alloy steel. The
dies are case hardened to a desired depth, while leaving the inner
portion (core) ductile. The hardened surface is highly resistant to
wear and exhibits quality gripping of tool joints. The inner ductile
core absorbs the shock of sudden impact and heavy torque. Teeth
edges are slightly rounded off to eliminate the teeth bite on drill pipe.
The combined effect is efficient operation in the long run. PAN Ind.
made these dies meet OEM specifications.
Dies for Manual Tong
Size in Inch Place of Use Interchange ability of PAN with
Type Dies PAN-No. Ref Part No.
→ BJ Type SDD, C, F, LF Manual Tongs Blue Diamond P55551-B 16401-6
with 1¼” slot
½” X 1¼" x 5" → BJ Power Casing Tongs Pyramid P55551-P 16401-2
→ Top Drive Torque Wrench Coarse P55551-C 16401-1
→ Foley Make Manual Tongs
Plain P55551-PL 16401
→ Lamb Power Casing Tongs
2-7/8”Round
2-7/8”Flat
3-1/2”Round
3-1/2”Flat
39
Dies for Woolley Slips
Body Size of Insert for D/Pipe Ref. Part No. Body Size of Insert for Ref. Part No.
Slips Size Slips D/Pipe Size
5½” x 5½” 757-054-0154 4½” x 4½” 757-044-0344
5½” x 5” 757-054-0150 4½” Long X 4½” x 4” 757-044-0340
5½” Long B 757-054-0144 757-044-0334
5½” x 4½” 4½” x 3½”
5½” x 4” 757-054-0140 4½” x 4½” 757-044-0144
5” x 5” 757-050-0350 4½” x 4” 757-044-0140
4½” Long B 4½” x 3½” 757-044-0134
5” Long B 5” x 4½” 757-050-0344
4½” x 2-7/8” 757-044-0127
5” x 4” 757-050-0340 4½” x 2-3/8” 757-044-0123
40
Inserts for Rotary Slips
Inserts for Rotary Slip ( 3-1/2” Body Size) Inserts for Rotary Slip ( 3-1/2” Body Size)
PAN Dies Part Ref. Dimensions PAN Dies Part Ref. Dimensions
No. Part No.CDI No. Part No.CDI
20160 2160 2-3/8” x 3-1/2” 20163 2163 3-1/2” x 4-1/2”
20161 2161 2-7/8” x 3-1/2” 20164 2164 4” x 4-1/2”
20162 2162 3-1/2” x 3-1/2” 20165 2165 4-1/2” x 4-1/2”
Inserts for Rotary Slip ( 5” Body Size) Inserts for Rotary Slip (5-1/2” Body)
PAN Dies Part Ref. Dimensions PAN Dies Part PAN Dies Part PAN Dies Part No.
No. Part No.CDI No. No.
20165 2165 4” X 5” 20168 20168 20168
20166 2166 4-1/2”x 5” 20169 20169 20169
20167 2167 5” x 5” 20170 20170 20170
41
42
EZY TORQUE HYDRAULIC CAT HEAD
PAN manufactured “EZY Torque Hydraulic Cat Head” is specially
designed to provide an accurate, smooth, constantly increasing
make-up and break out joint at rotary table, in a torque range of
40,000 to 1,50,000 ft-lbs.
PAN Ind.“EZY Torque Hydraulic Cat Head” are available to fit
individual rig requirements and operation parameters; it is
powered by an independent power source. The power unit can
be controlled form a convenient location on the rig with a
remote control module; it features a lever actuated control
valve, pressure gauge, and a pilot relief valve to provide pressure
operation and regulation. Using hig grade petroleum base
hydraulic fluid.
FEATURES
▪ Self-contained unit with hydraulic power & control unit suitable for safe
operation.
▪ Precise pressure control enables continuous makeup capability.
▪ Hydraulic operation of remote control module eliminates electrical hazards.
▪ Simple hydraulic circuit ensures trouble – free performance.
▪ Utilizes construction ensures durability.
▪ Angle Between pull line & torque arm is 90°.
▪ Positive displacement, tande pump provides efficient, steady hydraulic energy.
▪ Control module enables remote pressure regulation and cylinder operation.
Cylinder is mounted with the anchor adapter block.
▪ Contains Flame proof and explosion proof induction motor (10 HP, 1725 – 1760
RPM, 460 Volts, 60 Hz) to run hydraulic pump.
▪ Protection covers to protect electrical system from weather conditions and
operational situation (rain, water & mud) and hydraulic fluid from contamination.
▪ Tested at 3000 psi.
MODEL : PANEZT-10
Working Cylinder Stroke Line Pull Range Time Period of Wire Rope Size Wire Line Travel Overall
Pressure (Min) Length Stroke Weight (Apr.)
43
ROTARY TABLE ADAPTER
The Table Adapters: Is used to reduce rotary table Opening size for 49-
1/2” to reduce in 37-1/2” size & 37-1/2”to reduce in 27-1/2” with the
helpof this Adapter, Available as per the all type Master Bushing Solid &
Split Bushing.
With help of Rotary Slip Modified type, for Umbilical hose to pass the
hose through rotary table & rotary slip will hold the tubular with the help
of Bowl slotted type.
44
MANUAL TONGS
PAN Ind. Manual Tongs are necessary tools applied to make up and break out pipes. Changing lug jaws and latch
steps can adjust different handling sizes of the tongs.
They are interchangeable with other major manufacturer's tongs. Each tong features tough, heavy-duty designs
with heat-treated hinge pins and long-lasting "stagger tooth" tong dies (Blue Diamond, Pyramid). They are
designed and manufactured according to API Spec 7K.
MANUAL TONG
MANUAL TONG WELL SERVICING (EXTENDED CASING TONG) MANUAL TONG (CASING TONG)
45
DRILL PIPE POWER TONGS & CASING TONGS
Drill Pipe Power Tong is used for quick and safe making up and breaking out of drill pipes and drill collars hence they
reduces the drill time and lowers the cost. PAN Drill Pipe Tongs are designed and manufactured in according with API 7K.
CASING TONGS
Casing Tongs are used for quick and safe making up and breaking out of casing, they are placed in the drill hole to
maintainthe well opening. PAN Casing Tongs are available in variety of sizes and designed to handle high torque casing.
46
CASING BACK-UP TONGS
Model Size Range Max Torque (kN.m)
PCT-16Y 4” - 7” 16
▪ The Structure is compact, concise and light. Master Tong is driven by Low speed large torque hydraulic motor
which matching with manual control valve. The backup tong just likes a spanner. Total weight is approximately
100 Kgs.
▪ The Operating is briefness and convenience with high efficiency. Put the correspondence size jaw set into
master tong and the corresponding size glutting into backup tong, turning the reset knob in correct direction
then can make up and break out sucker rod by operating manual control valve. Two speed, snapping at low
speed, spinning at high speed.
▪ Large low gear torque, especially suitable for the instance that is difficult to break out sucker rod thread.
Model PAN29/2Y
Application Range : Sucker Rod: ¾”, 7/8”, 1”
High Gear Rated Torque 740 ft.lbs
Low Gear Rated Torque 1480 ft.lbs
High Gear Maximum Rotation Speed 120 RPM
Low Gear Maximum Rotation Speed 40 RPM
Opening of Tong Head 65 mm
Overall Dimension (L x W x H) 636 x 361 x 520 (mm)
Weight 100 Kg
Rated System Pressure 1450 PSI
Max Oil Supply 21 gpm
IRON ROUGHNECK
JIRN-110 Iron Roughneck can be remote controlled. It is designed according to API Spec 7K specifications. It is a
convenient and modularized product which can be used to make-up and break-out operation of drill pipes, drill
collars, casings and other type of couplings from 3½” to 8½”
47
DRILL PIPE / DRILL COLLAR SPINNER
PAN Ind. manufactured “Drill Pipe/Drill Collar Spinner” is the best replacement of the spinning rope (or chain). It
is applied for the mechanized spinning operation. The applicable range of pipe diameter is wide, and it
can be quickly & arbitrarily adjusted whenever necessary by changing the rollers. There are two configurations
for clamping apparatus: air tyre and air cylinder. It is suitable for working under temperature range of -6° C to
55° C. It is suitable for Drill Pipe / Drill Collar Size of 2-7/8” to 5½”.
PAN Pipe Spinners are durable, easy to use and designed for safety and longevity. The compact designs are self-
contained, requiring no dedicated power source.
FEATURES
▪ Powerful air Motor (Motor does not contain vane spring or push pins).
▪ Air Cylinder sub assembly, Door valve, throttle valve.
▪ Drive Roller, pressure roller & Roller arm sub-assembly.
ACCESSORIES
▪ Hanger Assembly (Metallic hanger, safety chain shackle, levelling screw, D shackle 2 Nos.)
▪ Air Line Assembly (Supply line 1¼”, 200 psi (min. b.p.) 50 ft length, Air Lubricator, filter, regulator and gauge).
▪ Muffler to reduce the noise.
48
TECHNICAL SPECIFICATION
Model PAN140-200 PAN254-250 PAN254-300Y
Drive Mode Pneumatic Hydraulic
mm 73.025 – 139.7 73.025 – 254 73.025 – 254
Size Range
in 2-7/8 – 5½ 2-7/8 - 10 2-7/8 – 10
Mpa 0.6 – 0.8 0.5 – 0.9
Air Pressure
Psi 90 – 120 72 – 130
Mpa 14
Pressure Rating
Psi 2000
N.m 2000 2500 3000
Max. Brake Torque
Ft.lbf 1475 1840 2210
Speed RPM 0 - 108 0 – 120 0 – 95
m³/min 6.8 15
Air Consumption
ft³/min 240 529
LPM 120 – 140
Flow
GPM 32 – 37
mm 1400 X 530 X 835 1250 X 570 X 465 100 X 560 X 700
Overall Dimension
in 55 X 21 X 33 49 X 23 X 18 44 X 23 X 28
Kg 467 440 400
Weight
lbs 1030 971 880
SPEED AND TORQUE OF SCREWING ON/OUT AND BRAKE TORQUE OF SPINNING WRENCH
Diameter of Drill Pipe Screw-on speed Screw-on torque at max power Brake Torque
in rpm N.m (lbf.ft.) N.m (lbf.ft)
5½ 56.8 1000 (738) 1500-2000 (1100-1475)
5 62.5 906 (668) 1360-1810 (1000-1335)
4½ 69.5 815 (600) 1220-1630 (900-1000)
4 78 725 (535) 1090-1450 (800-1070)
3½ 89.3 630 (465) 950-1260 (700-930)
2-7/8 108 520 (384) 780-1030 (575-760)
49
PAN Ind. SUPPLY RANGE OF ELEVATORS
Slip Type Elevators: HYC Casing Elevator, MYC Casing Elevator, YC Casing Elevator,YT Slip Tubing
01
Elevator, HYT Tubing Elevator, MYT Slip Tubing Elevator
02 Center Latch Elevator: “A” Series Center Latch Collar Type Elevator
18° Center Latch Elevator: “G” Series, MG Type 100 Ton Elevator, RG Type 150 Ton Elevator,MGG Type 250
03
Ton Elevator, GG Type 350 Ton Elevator
04 Collar Type Side Door Elevator: “X” Series, “SLX”- “SX” Elevator
05 Single Joint Elevator: S- Series Type “SJ”
06 Weld less Links
50
PAN Ind. SUPPLY RANGE OF SPIDERS
51
TYPE QQP PNEUMATIC SPIDER
The QQP series pneumatic spiders are mainly applied to hold the drill
pipes and tunings for their couplers fastening and removing during
the oil well repairing operation. The cylinder, which is driven by the
compressed air, activates the slip body lifting and lowering action, thus
it largely reduced the workers working strength and increased the
working effect. It is safe and reliable, easy in operation, and rational in
structure, which is an ideal tool for the oil well repairing operation.
These are manufactured as per API Spec 7K.
Model Max Load
Tons KN mm Inch
PANQQP/585 60 585 60.3 – 88.9 2-3/8” – 3½”
PANQQP/675 75 675 60.3 – 88.9 2-3/8” – 3½”
PANQQP/900 100 900 60.3 – 127 2-3/8” – 5”
Model Applicable Diameter of Tubular (Inch) Taper Rated Capacity (Short Tons)
PAN13-3/8/200 7” – 8-5/8” 1:3
9” – 13-3/8” 1:4
7” – 8-5/8” 1:3
PAN20/200 200 Ton
9” – 20” 1:4
PAN30/200 16” – 30” 1:4
PAN36/200 18-5/8” – 36” 1:4
PAN30/500 16” – 30” 1:3
PAN36/500 18-5/8” – 36” 1:3 500 Ton
PANH20/500 2-3/8” – 20" 1:3
52
SUCKER ROD WRENCH
PAN Sucker Rod Wrench is made of high quality alloy steel, and boasts the advantage of hardness and abrasion
resistance, its opening is applicable to the square shape of the steel – made sucker rod. The balanced design of
PAN sucker Rod Wrench can reduce the fatigue of users, which is an outstanding tool for manual mounting and
demountingsucker rod.
Split-Fluted Drill Pipe / Casing Protector are best suited for applications where there are high circulations of
mud. In fluted design the OD of the protectors are bigger hence making it more shock absorbing and the fluted
space on the outer surface of the protectors helps the mud to pass through the protectors easily.
53
AIR OPERATED THREAD PROTECTOR
PAN Ind. supply of Air-operated thread protector's ensure safe, reliable casing and tubing Pin-end protection. The
working principle of the Air protectors is based on pressurization by rig air (72 to 130PSI, or 5 to 9 bar) with the
help of Air Gun, ensuring easy installation and reliable protection for all API standard and premium threads.
54
S.NO. PLASTIC THREAD PROTECTOR S.NO. PLASTIC THREAD PROTECTOR
01 2-3/8” EUE PIN & BOX 12 3 -1/2” REG PIN & BOX
02 2-7/8" EUE PIN & BOX 13 4 -1/2" REG PIN & BOX
03 3-1/2” EUE PIN & BOX 14 6 -5/8" REG PIN & BOX
04 4-1/2" EUE PIN & BOX 15 7- 5/8" REG PIN & BOX
05 2 -3/8” IF PIN & BOX/NC-31 16 5 -1/2" FH PIN & BOX
06 2 -7/8” IF PIN & BOX/NC-31 17 6- 5/8" FH PIN & BOX
07 3 -1/2” IF PIN & BOX/NC-38 18 2- 7/8" PH-6 PIN & BOX
08 4” IF PIN & BOX /NC-46 19 3- 1/2" PH-6 PIN & BOX
09 4 -1/2" IF PIN & BOX/NC-50 20 4- 1/2" PH-6 PIN & BOX
10 2 -3/8” REG PIN & BOX 21 2 -7/8" HT PAC PIN & BOX
11 2 -7/8” REG PIN & BOX 22 NC- 35 PIN & BOX
S.NO. THREAD PROTECTOR IN NITRILE RUBBER S.NO. THREAD PROTECTOR IN NITRILE RUBBER
01 ¼” LP/NPT PIN & BOX 16 4” FIG/IF/XT 39/NUE PIN & BOX
02 4-1/2” REG/IF/EUE/PH 6/LTC/ NEW VAM
1/2” LP/NPT PIN & BOX 17
PIN & BOX
03 1” LP/NPT/AMMT PIN & BOX 18 5” STUB/BTC PIN & BOX
04 5-1/2” FH/BTC/LTC/STC/IF/GPDS 55/ HT55
1-1/4” AMMT PIN & BOX 19
PIN & BOX
05 1-1/2” AMMT PIN & BOX 20 6-5/8”REG/FH PIN & BOX
06 1-5/8” UN 18 PIN & BOX 21 7” BTC PIN & BOX
07 1” 66 NUE PIN & BOX 22 7-5/8”REG PIN & BOX
08 1” 90 EUE PIN & BOX 23 8-5/8”REG PIN & BOX
09 1-9/16” PIN & BOX 24 9-5/8” BTC PIN & BOX
10 1-315” NUE PIN & BOX 25 13-3/8” BTC PIN & BOX
11 2” FIG 1502/605/NPT/LP PIN & BOX 26 18-5/8” BTC PIN & BOX
12 2-3/8” REG/IF/EUE/PAC/NUE PIN & BOX 27 20” BTC PIN & BOX
13 2-7/8 “ REG/IF/NUE/EUE/HT/PH6/HTPAC/
28 WT 26 PIN & BOX
FOX/RBDS/ NEW VAM PIN & BOX
14 3” LP/NPT/FIG 1502/FIG 602 PIN & BOX 29 XT 50 PIN & BOX
15 3-1/2” REG/IF/EUE/PH-6/ NEW VAM/NUE/
30 ST 57 26 PIN & BOX
FOX PIN & BOX
55
LIFTING BAIL/CAP
PAN Ind. offers a wide range of Cast Steel Thread Protectors with
lifting bails from quality steel castings in conformity with ASTM A27
Grade 60-30. They are heat treated to give 60,000 psi Tensile
Strength and 30,000 psi Yield Strength and are furnished with heavy
duty bails suitable for picking up and laying down drill collars, drill
pipes.
Threads and Shoulders are precision machined as per API Standard.
Lifting Bails are Cast Steel Thread Protectors with Lifting Bails
ranging from 2-3/8” to 8-5/8” with REG, IF, FH, XH, H-90 and NC
connections.
Lifting Bails for Drill Collars and Drill Pipes
Standard Pin Standard Box
OD Protector weight Protector weight Standard weight per
Connection Size & Type
Range lb lb set
NC 23 6 6 12
3-1/8”
2-3/8” REG 6 6 12
–
NC 26 2-3/8” IF 6 6 12
3-1/2”
2-7/8” PAC 6 6 12
4-1/2” NC 31 2-7/8” IF 9 9 18
– 2-7/8” XH 9 9 18
4-3/8” 3-1/2” REG 10 10 20
4-1/2” NC 35 12 10 22
– NC 38 3-1/2” IF 12 10 22
5-1/8” 3-1/2” XH 12 10 22
5 – 5-3/4” NC 40 4” FH 17 17 34
5-3/4” 4-1/2” REG 15 17 32
–
6-1/4” 4-1/2” FH 15 17 32
6-1/4” NC 46 4” IF 16 21 37
–
6-3/4” 4-1/2” H90 16 21 37
6-3/4” NC 50 4-1/2” IF 15 21 36
– 5-1/2 REG 31 27 58
7-1/4” 5-1/2” H90 30 27 57
5-1/2” FH 30 28 58
7-1/4”
6-5/8” REG 27 28 55
–
6-5/8” H90 30 30 60
8-1/4”
6-5/8” FH 37 37 74
8-1/4” – 9” NC 61 32 32 64
7-5/8” REG 39 33 72
9”-10”
7-5/8” H-90 52 42 94
8-5/8” REG 50 46 96
10” – 11”
8-5/8” H-90 66 55 121
56
Lifting Bails for Drill Collars and Drill Pipes
Standard Pin Standard Box
OD Protector weight Protector weight Standard weight
Connection Size & Type
Range lb lb per set
– 2-3/8” EUE 7 7 14
– 2-7/8” EUE 7 7 14
– 3-1/2” EUE 9 9 18
– Fig 1502 10 10 20
57
DRESSER TYPE COUPLINGS
Material Grade: Style 38 & Style 40
Followers: MS Fabricated
Middle Ring: MS, SS304, SS316Bolts/Nuts: EN8
Stops: 316 Stainless Steel
Gaskets: Grade 42 Buna N (Others available on request)
Coating: Fusion-Bonded Epoxy as Standard
58
HAMMER LUG UNION
PAN I n d . offers a complete range of hammer unions in standardand
sour service. Hammer unions are commonly used in oilfield industry to
seal two pieces of pipe or hose together and connected by threads or
welds. They are high-pressure threaded or welded connections with two
halves, a threaded female half and a wing male half with swivel nut that
fit together and seal upon turning and then hammering the nut half
together with the threaded half. To fit different sizes of pipe or hose,
corresponding types of hammer unions are designed. In most cases,
they come in sizes from 1" up to 10" and in pressures from 1,000 psi up
to 15,000 psi. We distinguish pressure ratings with different colors.
Below is the chart for complete pressure rating and color codes for each
high-pressure hammer union available.
59
OIL SAVERS
These are made of specially formulated compounds which are tough and have a
long life. Oil Saver Rubbers are molded from a special compound of oil, gas and
abrasion-resistant rubber for long service life. Oil and other fluids are removed
from the wire line and allowed to re-enter the well, which helps prevent
potential well-site contamination. Our savers are supplied in different colors red,
green, blue etc. These are made of hardness ranging from 35° to 55° A.
Type H
HSPC Description Replacement Rubber for OEM Units
Type H 3/8" - 5/8" Guiberson Type H
Type H 3/8" - 5/8" Soft Guiberson Type H
Type H 5/16" - 7/16" Soft Guiberson Type H
ROD WIPERS
They aid in keeping hydrocarbon seepage to a minimum while under pressure. They clean rods of excessive oil
and waxes to provide a safer working environment. Size: 5.15" O.D. 0.609" LD.
BJ Equivalent
HSPC Normal Size Replacement Rubber for
Description OEM Units
BJ - 5/8” .612” BJ Type Rod Wiper
BJ - 3/4” .750” BJ Type Rod Wiper
BJ - 7/8” .875” BJ Type Rod Wiper
BJ - 1” 1.000” BJ Type Rod Wiper
60
ADAPTORS & CROSSOVERS
PAN Ind. offers a range of Adapter Crossovers and Changeovers in integral,
threaded and welded construction for sizes up to 5 inches in different
combination as per customer requirement. These Crossovers are
manufactured for pressure rating up to 15,000 PSI.
PUP JOINT
PAN Ind. offers a range of Pup Joints with Integral Hammer Union end
connections.
These Pup Joints are used on high pressure discharge lines, choke and kill
lines,auxiliary flow and other applications.
These light weight Pup Joints are available in lengths ranging 1 feet to 12
feetand sizes from 2-inch to 4 inch for pressure rating 6000 to 15,000 PSI.
Pup Joints in welded, NPST and NPT (Threaded) Construction as per
customer requirement.
PAN Ind. Offers Adapter & Spacer Spools as per API 6A Specification &
according to the customer requirement with reference to size and length.
These items are supplied with full material traceability and necessary
documents.
FLANGES
PAN Ind. offers a wide range of flow products as per API 6A Specification.
These products are also manufactured as per customer specification for
PSL Levels, Materials, Temperature class and supplied with complete
certification and necessary documents.
61
ROTARY SUBS
PAN Ind. Rotary Subs include Lift Subs, Lift Plug, Saver Subs, Straight OD Subs and Reduced Section Subs. These
subs are manufactured & supplied from 4145 Alloy Steel. All Subs material is MPI tested. These are fully heat
treated to a Brinell hardness range of 285-341and have an Izod impact strength of 40 Ft/lb minimum.
The connections of Rotary Subs are manufactured as per API specification and API monogrammed The Rotary
Subs are available in standard lengths of 18”, 36" and 48". Any other length can also be supplied.
LIFT SUB
A Lift Sub makes the handling of drill collars, shock tools, directional equipment and other
tools safe and efficient by using drill pipe elevators. Lift subs can be easily screwed to the
top of the tool and feature an elevator groove. PAN lift subs are complied with API
specifications.
LIFT PLUG
The Lift Plug is a small easy-to-handle sub that forms the top of the drill collar. It has a lifting
flange that acts as a safety stop when drill collars without elevator recesses are being pulled
out of the hole. For easing handling of the Lift Plug its center section isbored out.
SAVER SUB
Saver Sub is used to extend the life of the Kelly by taking the connection wear each time it
is make-up to a drill stem component. It can be easily repaired and also inexpensive to
replace. The saver sub can also be equipped with a rubber protector to reduce casing
wear resulting from contact damage with a lower Kelly connection.
STRAIGHT OD SUB
Straight OD Sub is used to connect drill stem components that have a similar outside
diameter. The drill bit, downhole tools, heavy weight drill pipe and drill pipe can be
crossed over using a straight OD sub.
Reduced Section Sub is used to connect drill stem components that have different
diameters that warrant the cross-sectional change necessary to accommodate different
connections. This sub would be used to crossover large OD drilling tools or a tapered drill
collar string.
62
CABLE PROTECTION
PAN offers wide range of cable protection solutions to reduce cable risks and prevent expensive workovers.
Downhole Electrical cables are vulnerable to frequent failure due to their natural limits of breaking strain or poor
operational factors. Also the highly deviated wells may also increase the cable tensions. Our cable protectors are
available in both standard and customized systems.
63
BUTTERFLY VALVE
PAN Ind. Butterfly Valves are manufactured with the strongest and durable
materials to ensure a long dependable and trouble free service. A valve is
one which can be used for isolating or regulating flow. PAN is a leading
manufacturer, supplier of valves in India and a leading exporter of valves to
many international locations. Today PAN is a widely recognized leader in
manufacturing and exporting of superior quality Industrial valves for a wide
range of applications. Our valves and other flow control products have a
strong reputation for reliability, quality and service. PAN Valves are
manufactures as per API 609 Spec., BS-5155, EN593.
Type: Wafer Type / Lug Type / Centric Disc / Offset Disc / Double langed
Manufacturing Standard: API 609 / BS 5155
Testing Standard: API 598 / ASME B 16.34
Size Range: 50NB To 600NB
Pressure Rating: PN10 / PN16 / Class 150
Temperature Range: 90°C Approx.
MATERIAL OF CONSTRUCTION
Valve Parts
Cast Iron I.S. 210 Grade FG200/220 Ductile Cast Iron GG40; Cast Carbon Steel
ASTM A-216 Grade WCB: Cast Stainless Steels CF8 & CF8M; Ductile Iron/SG Iron to
Body:
BS EN 1563 Gr. EN-JS1030
Ductile Cast Iron GG40; Cast carbon Steel
ASTM A-216 Grade WCB; Cast Stainless Steels CF8 & CF8M; 316 SS/ASTM A 351 Gr
Disc:
CF8/CF8M With Polished Periphery
Seat: Nitrile, EPDM, Viton
Seal Holding Rings on Disc: Renewable AST. 182 GR. F6 HELD BY SS SCREW
Flange less Wafer Type to fit between existing flanges without gasket: Flow
Ends :
Control Lever Operated
FEATURES:
▪ Easy and quick opening and closing. Small fluid resistance. It can be frequently operated.
▪ Simple structure, small size, and light weight.
▪ It can transmit mud, and has the least amount of liquid accumulated at the outlet of the pipeline.
▪ Under low pressure, good sealing can be achieved.
▪ Good regulating performance
64
BALL VALVES
PAN Ind. Ball Valves are manufactured to meet API Std. 6D and BS 5351, and
tested to API 6D/ API 598/ ASME B 16.34.
These valves are used for quick shut off and low emission application.
Design Standard: BS-5351 / API-6D (Single Piece Design)
Face To Face Dimensions: ASME B 16.10 / API 6D
MATERIAL OF CONSTRUCTION:
Made from barstock
Figurein carbon steel or stainless steel (304, 316.304L, 316L, 321), Alloy 20, Hastelloy B & C.
No.
81
Castings in carbon steel to ASTM A 216 GR.WCB.
Castings in stainless steel to ASTM A 351 GR. CF8/CF 8M/CF 8C/CF 3/CF 3M. Alloy20, Hastalloy B & C.
Castings in C.I. to I.S. 210 Gr. FG 200/220/260/300/350/400
Castings in Alloy Steel to ASTM A 217 C5, WC6, WC9, WC12
Casting in Bronze.
Size Range: 15mm to 600 mm
Pressure Rating: Class 150/300/600/800/900/1500/2500
2 Piece / 3 Piece, Full or Reduced Port, Floating or Trunnion Mounted, Fire Safe Design available.
ENDS:
FEATURES:
▪ 3 Piece, Thread Ends BSPT-11, FULL BORE(ASME Class 150, 300, 600 & 2500), ISO 17292
▪ Positive shut off
▪ Longer life
▪ Quick in function
▪ No lubrication
▪ Visual On/Off indication
▪ Compact design
▪ Corrosion resistant
▪ Low pressure drop
▪ Simplicity
65
PAN Ind. RANGE IN VALVES
NON RETURN VALV SWING TYPE FORGED STEEL CHECK VALVE SWING CHECK VALVE
66
BALL VALVE THREE PIECE SCREW END
3 WAY MOTORISED CONTROL VALVE BALL VALVE
67
WAFER TYPE CHECK VALVE
DUAL PLATE CHECK VALVE PINCH VALVE
68