Professional Documents
Culture Documents
100H Inspection Tables
100H Inspection Tables
DO A DI FOR DAMAGE, CONDITION AND PLAY (NO REMOVAL REQUIRED) (AXIAL PLAY CHECK ONLY) (MAXIMUM
PLAY ALLOWED: 0.25 MM -0.0099 IN) . REFER TO: 39-A-62-22-00-00A-31AA-A
62-36 ROTATING CONTROLS INSTALLATION -PITCH CHANGE LINK ASSEMBLY SPHERICAL BEARINGS:
DO A DI FOR CONDITION, DAMAGE AND PLAY (REMOVAL OF PITCH CHANGE LINK ASSEMBLIES
REQUIRED) (AXIAL PLAY CHECK ONLY) (MAXIMUM PLAY ALLOWED: 0.2 MM -0.0079 IN). IF PLAY FOUND
IS BETWEEN 0.1 AND 0.2 MM (0.0039 AND 0.0079 IN), INSPECTION INTERVAL MUST BE REDUCED AT 100
FH. REFER TO: 39-A-62-31-00-00A-31AB-A
64-27 ROTATING CONTROLS INSTALLATION -PITCH CHANGE LINK ASSEMBLY SPHERICAL BEARINGS
DO A DI FOR CONDITION, DAMAGE AND PLAY (REMOVAL OF PITCH CHANGE LINK ASSEMBLIES REQUIRED) (AXIAL
PLAY CHECK ONLY) (MAXIMUM PLAY ALLOWED: 0.2 MM -0.0079 IN). IF PLAY FOUND IS BETWEEN 0.1 AND 0.2 MM
(0.0039 AND 0.0079 IN), INSPECTION INTERVAL MUST BE REDUCED AT 100 FH.
Make sure that the measured distance Y is less than 26.90 mm (1.06 in).
Make sure that the measured distance X is more than 24.35 mm (0.96 in).
If the distances that you found are not in the given limits, replace the anti-rotation block (3) with a new item. Refer
to 39-A-62-22-07-00A-520A-A and 39-A-62-22-07-00A-720A-A. and record the details in below Table.
62-50
MAIN ROTOR DAMPER SPHERICAL BEARINGS
DO A DI FOR ALIGNMENT OF SLIPPAGE MARKS AND FOR SEALANT INTEGRITY ON THE STAKING AND
CERAMIC COATING DAMAGE OF EYE END ASSY AND BODY END ASSY SPHERICAL BEARINGS. REFER TO: 39-
A-62-22-02-01A-31AA-A. NOTE: TASKS APPLICABLE ONLY TO MAIN ROTOR DAMPER P/N 3G6220V01353.
If you find that the bearing (3) has one or more defective conditions, replace the rod end (2). Refer to data
module 39-A-62-22-02-01A-921A-B.
If you find that the bearing (5) has one or more defective conditions, replace the lag damper (1). Refer to
data modules 39-A-62-22-02-00A-520A-A and 39-A-62-22-02-00A-720A-A.
If Lag Damper replaced If Damper rod end replaced
MR Damper Rectification WS
SN New PN New SN New PN New SN Ref
(if replaced):
100 Hours Mandatory Inspection Tables
If the damper body end (3) moves at a value more than 30 Nm (265 lbf in) Replace the lag damper (1). Refer to 39-
A-62-22-02-00A-520A-A and 39-A-62-22-02-00A-720A-A. Record the details of defective part in below Table
If the value is higher than 30.0 Nm (265.5 lb in) for Damper rod end, replace the damper rod end (see AMP DM n°
39-A-62-22-02-01A-921A-B). Record the details of defective part in below Table.
MR Torque If the Torque value recorded is higher than 30.0 Nm
Damper SN Value Damper rod end replaced
………………… Yes ☐ No ☐
………………… Yes ☐ No ☐
………………… Yes ☐ No ☐
………………… Yes ☐ No ☐
………………… Yes ☐ No ☐