Professional Documents
Culture Documents
3306c Cylinder Head Install 1
3306c Cylinder Head Install 1
• Home
• Caterpillar
• sebr05170132
Cylinder Head
Remove Cylinder Head (D330C, D333C, 3304 & 3306 Industrial Engines)
start by:
2. Remove bolt and clip (3). Remove sensing line (5) for water temperature gauge.
Remove bolt and clip (2). Remove ammeter gauge wire (1). Remove bolts (4).
3. Remove fuel injection lines. Put caps on lines and pump openings. Disconnect
turbocharger oil supply and drain lines.
5. Fasten a hoist to the cylinder head and remove it from the cylinder block.
Weight of the assembly is 360 lb. (163 kg).
Install Cylinder Head (D330C, D333C, 3304 & 3306 Industrial Engines)
1. Clean sealing surfaces of the cylinder head and block. Install a new gasket on
the cylinder block and install the cylinder head.
3. Put 9M3710Anti-Seize Compound on threads of the cylinder head bolts. Install the
bolts and washers and tighten the bolts in the following sequence:
1 - Tighten all bolts with numbers in order to 115 lb.ft. (15.9 mkg).
2 - Tighten all bolts with numbers again in order to a torque of 175 ± 5 lb.ft.
(24.2 ± 0.7 mkg).
3 - Last, tighten all bolts (hand torque only) with numbers again in order to a
torque of 175 ± 5 lb.ft. (24.2 ± 0.7 mkg).
4 - Tighten all bolts with letters in order to a torque of 22 lb.ft. (3.0 mkg).
5 - Tighten all bolts with letters again in order to a torque of 32 ± 5 lb.ft. (4.4
± 0.7 mkg).
6 - Last, tighten all bolts (hand torque only) with letters again in order to a
torque of 32 ± 5 lb.ft. (4.4 ± 0.7 mkg).
4. Make an adjustment of the inlet valves to get a clearance of .015 (0.38 mm) and
exhaust valves to get a clearance of .025 in. (0.64 mm).
5. Connect turbocharger oil supply and drain lines. Remove caps from fuel injection
lines and pump openings. Install fuel injection lines. Tighten nuts to a torque of
30 ± 5 lb.ft. (4.1 ± 0.7 mkg).
6. Install bolt and clip that hold ammeter gauge wire. Install bolt and clip that
hold water temperature sensing line.
end by:
Remove Cylinder Head (D330C, D333C, 3304 & 3306 Marine Engines)
start by:
4. Remove turbocharger oil supply line (3) and oil drain line (5).
5. Remove bolts (7) that hold elbow (8) to cylinder head. Loosen clamp (9) and
remove elbow (8).
6. Disconnect the sensing line (11) for the fuel ratio control.
7. Remove the fuel injection lines (10) and put covers on all fuel openings.
8. Remove the lifting eye (12) from the rear of the engine.
9. Remove the remainder of the bolts that hold the cylinder head to the cylinder
block.
10. Install one 3/8"-16 NC forged eyebolt and fasten a hoist and a strap. Remove
the cylinder head. Weight of the assembly is 400 lb. (181 kg).
Install Cylinder Head (D330C, D333C, 3304 & 3306 Marine Engines)
1 - Tighten all bolts with numbers in order to 115 lb.ft. (15.9 mkg).
2 - Tighten all bolts with numbers again in order to a torque of 175 ± 5 lb.ft.
(24.2 ± 0.7 mkg).
3 - Last, tighten all bolts (hand torque only) with numbers again in order to a
torque of 175 ± 5 lb.ft. (24.2 ± 0.7 mkg).
4 - Tighten all bolts with letters in order to a torque of 22 lb.ft. (3.0 mkg).
5 - Tighten all bolts with letters again in order to a torque of 32 ± 5 lb.ft. (4.4
± 0.7 mkg).
6 - Last, tighten all bolts (hand torque only) with letters again in order to a
torque of 32 ± 5 lb.ft. (4.4 ± 0.7 mkg).
4. Make an adjustment of the inlet valves to get a clearance of .015 (0.38 mm) and
exhaust valves to get a clearance of .025 in. (0.64 mm).
6. Remove covers from all fuel openings and install fuel injection lines (1).
Tighten nuts to a torque of 30 ± 5 lb.ft. (4.1 ± 0.7 mkg).
7. Connect the sensing line (2) for the fuel ratio control.
8. Install water elbow and install the bolts that hold it. Tighten hose clamp.
10. Install turbocharger shield (3) and the bolts and nuts (4) that hold it.
11. Install the bolts (6) that hold the turbocharger oil drain line.
12. Install the bolts (5) that hold the turbocharger oil supply line.
end by:
https://avsmanual.com/i.caterpillar/sebr05170132/