Professional Documents
Culture Documents
BITS Pilani
Pilani Campus
BITS Pilani
Pilani Campus
Introduction
Control of material in manufacturing. Control of the flow of material from a raw state to a finished product. Most industries buy material, transport it to the plant, change the material into parts, assemble parts into finished products, and sell and transport the product to the customer. The flow of material as they progress, with the aid of inventories, through the production cycle can be diagrammed as shown in the following figure.
Specific objectives of the inventory management and control group are to maintain optimum inventory levels and inventory turnover for operation of the business at maximum profit Through the control of inventories, it should be ensured that the right material in the right quantity and of the right quality is made available at the right place at the right time.
Inventory Classifications
In the same manner that we identify the various functions in material management with the flow of goods, we can identify the different types of inventories or stocks of material maintained in a manufacturing plant. All plants use the same general classification of inventories, including raw material, purchased parts, work-in-progress, finished goods, and supplies.
Raw Material
A raw material inventory includes all items that, after being received at the plant, require additional processing before becoming an identifiable part of the finished product. It is obvious that the finished product of one plant- such as roll, bar, and sheet steel- may be the raw material of the next industrial purchaser.
Purchased Parts
This classification of inventory is applied to component parts of a product that need no additional processing before being assembled into the finished product. In some cases this material may be classified as raw material inventory. More times than not, however, a separate classification is justified. The TV picture tube that is the finished product of one manufacturer becomes a purchased part to the television set manufacturer.
Work-in-Process
This classification of inventory is self-explanatory. All material that leaves either raw material stores of purchased parts stores enters the work-in-process inventory until the product is completed and placed in finished goods. Work-in-process is the inventory of material, the flow of which is controlled by production control procedures to be discussed in a later chapter.
Finished Goods
This classification applied to the quantities of finished goods that are held at the factory awaiting shipment. It will include stocks held in warehouses owned and operated by the manufacturer, or stock held on dealers floors on consignment. The value of the finished goods inventory is usually very high and a principal factor in the financial management of the company. A typical example of this is the piston ring manufacturer, who, in addition to supplying the original car manufacturer, also maintains large stocks of many different sizes of piston rings in automotive supply houses for quick service to the auto repairman. These stocks are on consignment; that is the piston ring manufacturer does not receive any payment for the goods until they have been sold by the distributor.
BITS Pilani, Pilani Campus
Supplies
All the materials needed for the operation of the plant that are not used as parts of the finished product are classified as supplies. In the chapter on cost accounting we have identified this inventory classification as indirect material. On the other hand, the material that becomes part of the finished product is called direct material. Lubricating oils, sweeping compound, light bulbs, and many other items fall into the supply category.
Optimum Inventory
The complex relationship between modern industry and its market presents a real problem in the size of inventories that should be maintained. Large inventories in the face of declining sales mean lower profits. Small and inadequate inventories in the face of an increasing market demand may result in the loss of sales to competitors and a decreased profit. Recognition of these conditions should indicate that the optimum inventory is not necessarily either the minimum or the maximum level of inventory; nor is it operation at a maximum inventory turnover.
Inventory Turnover
A very common index of inventory control, inventory turnover is the ratio of the value of the product shipped to the average investment in inventory for the same period. Inventory turnover = (value of product shipped)/(value of average inventory) Obviously, the higher this index, the lower the inventory levels and the lower the cost of maintaining the inventories. Also, it is obvious that a high index indicates a shorter manufacturing cycle with all the saving inherent therein.
Rate of Usage
The anticipated rate of usage of the part must be considered together with the time required to produce a replacement lot. Quantities should be established such that at all times stock will be available to the assembly departments. This principle is used by the materials control group in determining inventory levels.
Ordering Cost
Next in importance is the cost to acquire the item. In a manufacturing situation this would be a setup cost. If the part is purchased an ordering cost would be incurred. For a cost such as this, the quantity purchased or made is important the larger the quantity, the lower the perpiece cost.
Deterioration or obsolescence
Another factor to be considered is the deterioration or obsolescence of a large stock of parts. All these factors must be weighed by management and an economic lot size determined that will result in the acquisition of parts at an optimum cost per unit.
=T =
Working Days
/ Year
d =
D
Working Days / Year
ROP = d L
D = Demand per year S = Setup (order) cost per order H = Holding (carrying) cost d = Demand per day L = Lead time in days
BITS Pilani, Pilani Campus
EOQ Example
Youre a buyer for SaveMart. SaveMart needs 1000 coffee makers per year. The cost of each coffee maker is $78. Ordering cost is $100 per order. Carrying cost is 40% of per unit cost. Lead time is 5 days. SaveMart is open 365 days/yr.
SaveMart EOQ
EOQ
D= S= C= I= H= H= 1000 $100 $ 78 40% CxI $31.20
2 D S H
2 1000 $100 EOQ $31.20
EOQ = 80 coffeemakers
SaveMart ROP
ROP = demand over lead time = daily demand x lead time (days) =dxl
D = annual demand = 1000 Days / year = 365 Daily demand = 1000 / 365 = 2.74 Lead time = 5 days
Computer Assistance
The computer is the direction to go for assistance if its use can be justified. One can do much posting of numbers by hand for the rental or purchase price of a computer, but there will be a point in almost every companys operation when the inventory problem can best be handled by computer, most often using a database management system.
Inventory Costs
Sales personnel wish their company to stock large quantities of all items in the product line so they can meet even the most unreasonable demands of their customers. Typical production personnel wish to keep large quantities of parts on hand so there is never any danger of a production line having to shut down for lack of parts.
Type of Product
If the materials used in the manufacture of the product have a high unit value when purchased, a much closer control is usually in order. Jewelers are much more careful with their stock of diamonds than they are with display cases full of lowpriced costume jewelry. This same principle holds in manufacturing.
Type of Manufacture
The close relationship between the type of product and the type of manufacture makes an analysis of the effect on inventory controls somewhat repetitious. Continuous manufacture is common to the manufacture of standard products. However, some standard products are made in batches. Where continuous manufacture is employed, the rate of production is the key factor. Here, as a matter of fact inventory control is of major importance and in reality controls the production of the product.
Volume
The volume of product to be made, as represented by the rate of production, may have little effect on the complexity of the inventory problem. Literally millions of brass bases for light bulbs are manufactured each month involving the control of only two principal items of raw inventory.
Inventory Management
The planning of the control of inventory can be divided into two phases: Inventory management Inventory control. Inventory management consists of:
1.
2. 3. 4.
Determination of optimum inventory levels and procedures for their review and adjustment Determination of the degree of control that is required for the best results Planning and design of the inventory control system Planning of the inventory control organization.
Degree to Control
Inventory management must decide just how much control is needed to accomplish the objective. The least control as evidenced by systems, records, and personnel- that is required to perform the function efficiently is the best control. This problem of the degree of control can be approached from the viewpoint of quantity, location and time.
Just-in-Time Concept
Much publicity was given during the early 1980s to the Japanese style just-in-time inventory concepts. The goal of JIT is simple enough; get the material to its next processing point just at the time it is needed. Theoretically, then, no inventory will be needed. JIT can be implemented with manufacturing work-in-process or with material purchased from outside vendors. The latter will require coordination with these vendors. One truck transportation company obtains much of its business by catering to companies that must deliver parts to other companies just in time. The Toyota company in Japan has developed a scheduling discipline for internal control of in process material movement, called kanban, which substantially reduces WIP inventories and hence reduces the associated costs.
Inventory Control
The inventory control group puts the plans of inventory management into operation. These plans are seldom complete in every detail. The day-to-day planning required to meet production requirements the second phase of planning for inventory control is the responsibility of this group.
The basic information normally carried on perpetual inventory records includes: 1. On order: This part of the record shows the quantity of material ordered but not received. Now order are added in this column and receipts subtracted. 2. Received: All receipts are posted here; there is no balance quantity in this column. 3. On hand: This balance figure represents the quantity of the item that should be in the stock room. Receipts are added to this column and issues subtracted. 4. Issued: A record of all quantities issued to the factory is entered in this column. 5. Allocated: In this column are entered the quantities to be reserved for later issue for specific order. Reserving of materials still in this stock room will ensure their availability when they are needed on the manufacturing floor. 6. Available: This is the quantity of material on hand that is still available for assignment to future orders.
BITS Pilani, Pilani Campus
Pricing Inventories
There are four basic ways to price inventories for accounting purposes: 1. First in first out (FIFO): Under this procedure, all issues are priced at the cost of the oldest lot until that lot is used up. Then the price of the next oldest lot is used, and so on. In other words the first price into the inventory is the first price out of the inventory when issuing materials. 2. Last-in-first out (LIFO): under this procedure, all issues are priced at the cost of the newest lot until that lot is used up. Then the price of the next to newest lot is used, and so on. If, in the meantime, another lot comes in, the price of this even newer lot is used when issuing material until the entire quantity involved is issued, at which time the price reverts to the next newest unused quantity.
BITS Pilani, Pilani Campus
3. Average value: Under this system, the values of issues are computed by using the weighted average cost of the material in stock. As new material is received at slightly different prices a new computation must be made as to the weighted average cost of the total material on hand. 4. Standard costs: A standard cost is established for each material, and all disbursements are charged out at this standard value regardless of the price actually paid for the material.
Bin Control
We have discussed perpetual inventories at length. Again they are applicable to what we have previously designated as high or intermediate value inventory items. It is still evident that such procedures as we have touched on briefly are costly. For those items in which the cost of keeping such records cannot be justified, a bin control is usually adopted.
Storerooms
Storerooms (or stock rooms) are areas in which material is held in controlled storage. All material received in the area is counted and recorded, none is issued without the proper stores requisition. Controlling materials in such a manner costs money in terms of space, personnel, and handling. These costs must be offset by better service to the factory and reduced loss of materials.
Physical Inventories
A physical inventory is used to verify the balances shown on the perpetual inventory records and to obtain a correct count on all items of inventory that may be on a bin control system. Physical inventories may be taken in two different ways. Using the first method, plans may be made for a complete shutdown of manufacturing activity.
Thank You