Professional Documents
Culture Documents
May 2014
Version 1
Agenda
IP-20G
IP-20S
IP-20C
IP-20
Platform
IP-20LH
Compact
All-Outdoor
Terminal / Terminal /
Single-Carrier Single-Carrier
IP-10Q
Aggregation
Nodal Nodal
Compact
All-Outdoor
Terminal / Terminal /
Single-Carrier Single-Carrier
Q2/2014
IP-20G
IP-10Q
Aggregation
C C
C RFU-C 1+0
1+1
C C
1+0
IP-20N C IP-20C
C
2+0
C
1+1
C
IP-20N
C
C IP-20N
1+0 C C
C
1+0
2+0
C
2+0 1+0
IP-10G C C
IP-20N
IP-20G
C C
IP-20G IP-10G
• 6 x 1 GE interfaces total
• 2 x dual mode GE electrical or cascading interfaces (RJ-45)
• 2 x GE electrical interfaces (RJ-45)
• 2x GE optical interfaces (SFP)
• Optional: 16 x DS1 interfaces
• Single or dual radio interfaces (TNC)
• Single or dual power-feeds (-48v)
• Sync in/out interface
• Management interfaces
• Terminal – RS232 (RJ-45)
• 2x FE electrical interfaces (RJ-45)
• External alarms interface
• RFU-C support
• IP-20G maintains high capacity, with up to 1024QAM modulation in its first SW release (T7.7), and up to
2048QAM in future release
9
FibeAir IP-20G – Front panel description
Passive cooling
(Fan-less design)
1RU
Power
16 x E1/DS1s External
1 or 2 RFU -48V DC
(optional) Alarms 2 x FE
2 x GE interfaces (Single-feed &
MDR69 connector (DB9) Management
Optical (TNC) Dual-feed options)
(RJ45) 2 x Dual-Mode: (SFP)
GE Electrical or
Sync in/out
‘Cascading’
(RJ45)
Terminal (RJ45) 2 x GE
(RJ45) Electrical
(RJ45)
• If the user only needs to use a single management interface, a standard Cat5 RJ-45 cable (straight or
cross) can be connected to the MGMT interface.
• To access both management interfaces, a special 2 x FE splitter cable can be ordered from Ceragon.
• Port Status LED – The LED for management interface 1 is located on the upper left of the MGMT
interface. The LED for management interface 2 is located on the upper right of the MGMT interface.
• ACT – Indicates whether the interface is working properly (Green) or if there is an error or a
problem with the interface’s functionality (Red), as follows:
• Off – The radio is disabled.
• Green – The radio is active and operating normally.
• Blinking Green – The radio is operating normally and is in standby mode.
• Red – There is a hardware failure.
• Blinking Red – Troubleshooting mode.
• LINK – Indicates the status of the radio link, as follows:
• Green – The radio link is operational.
• Red – There is an LOF or Excessive BER alarm on the radio.
• Blinking Green – An IF loopback is activated, and the result is OK.
• Blinking Red – An IF loopback is activated, and the result is Failed.
• RFU – Indicates the status of the RFU, as follows:
• Green – The RFU is functioning normally.
• Yellow – A minor RFU alarm or a warning is present, or the RFU is in TX mute mode, or,
in a protected configuration, the RFU is in standby mode.
• Red – A cable is disconnected, or a major or critical RFU alarm is present.
• Blinking Green – An RF loopback has been activated, and the result is OK.
• Blinking Red – An RF loopback has been activated, and the result is Failed.
• FibeAir IP-20G receives an external supply of -48V current via one or two power
interfaces (the second power interface is optional for power redundancy).
• The IP-20G monitors the power supply for under-voltage and includes reverse
polarity protection, so that if the positive (+) and negative (-) inputs are mixed up, the
system remains shut down.
• The allowed power input range for the IP-20G is -40V to -60V. An under voltage alarm
is triggered if the power goes below the allowed range, and an over voltage alarm is
triggered if the power goes above the allowed range.
• The synchronization interface contains two LEDs, one on the upper left of the interface and one
on the upper right of the interface, as follows:
• T3 Status LED – Located on the upper left of the interface. Indicates the status of T3 input clock,
as follows:
• Off – There is no T3 input clock, or the input is illegal.
• Green – There is legal T3 input clock.
• T4 Status LED – Located on the upper right of the interface. Indicates the status of T4 output
clock, as follows:
• Off – T4 output clock is not available.
• Green – T4 output clock is available.
• Blinking Green – The clock unit is in a holdover state.
Sync
48V
Radio Interface 1
Power
48V Supply Framer Modem IF
RFU
Interface RFU
(Optional Dual
Feed)
ABC/BBS XPIC
Sync
Radio Interface 2
Sync
In/Out Sync Unit (Optional)
FE Management
Interfaces
CPU
Terminal
Ethernet
Ethernet Services
TDM Interfaces
GE Traffic
Interfaces
(Optional)
Network
Processor TDM
16 x E1
TDM Pseudowire Services Services Framer LIU
Interface
Processor
GE/Cascading Services
Interfaces
Engine
TDM Cross
Connect
Native TDM
Services
21