Professional Documents
Culture Documents
6600 Installation - 2021V1
6600 Installation - 2021V1
Picture 1 Picture 2
steps:
Remove 1. First, confirm whether the rack placement position and the bed panel are
this
fixed block the horizontal. If not, adjust them to the horizontal state through the gasket .
2. Remove the longitudinal and transverse fixing blocks and screws from the
bed, as picture 1,2,5.
Picture 5
Steps:
1. Take out the column, chest film rack, film box, and put them in order, as
picture 1.
2. Need 3 people to put the column up, one person will keep the column
Use the M10*22 screws ,
fix the column
Stand the chest
base and block base alignment, with the M10*22 screws to fixe the
on the block base.
radiography frame Picture 4 column on the block base, as picture 3.
Picture 3 up and place it in the
designated position
3. Need 3 people lift the chest film column to the base, that was placed in
the designated position, and put it up, as picture 4.
Picture1 Picture2
Steps :
1. Remover the metal cover of the collimator. Loosen the sheet metal
screws of the two side buckles and push them outward to remove the
mounting plate, as the picture 1,2.
Remover the metal of
Loosen the sheet metal
the collimator
screws of the two side
Tighten
picture6
this screws
:
3.5 meters
Serial cable
Picture 3
Angle identification cable
Steps:
1. Connect the Angle identification cable to the touch switch, as
Connect the Angle
identification cable picture 1,2.
to the touch switch
voltage cable to
the tube
Pull out the electromagnet wire
Picture 1 Picture 2 of tube rotate. And connect this
two wires together.
Steps :
1. Insure the cable length from the tube housing to the tube
Insure this arm is: 65cm, as picture1.
length is : 65cm
Picture 3 Picture 4
3. The cable direction is depends on the chest radiograph
stand placed left or right, follow the chest radiograph stand
opposite direction, as picture 4.
by cable tie
pulley magnet cable
2. Motor, encoder and pulley magnet cables are wired from the
are wired from here ,
go through this Picture 4 Picture 5 3. First, the encoder wire is threaded through the slot at the bottom
Picture 3 port
of the counterweight sealing plate, and lock the plate, then lock the
motor and encoder cable into the wire slot and lock the wire slot, as
picture 4,5.
of chest radiography frame 2. Use a 50cm winding pipe to wind up the cables of tube lifting
Picture 3 motor and potentiometer, as picture 4.
Connect
Picture 4
the
electromagnet
Paste a cable clip at 3. Paste a cable clip at this position to fix the cables of tube lifting
line of bed
this position to fix
motor and potentiometer, as picture 4.
the cables of tube
fix
the
Picture 1 Picture 2
Remove the
3. First remove the bucky shell, and then fix the Bucky on the
mounting block with hexangular set screws, as picture 3.
Picture 3 Picture 4
First remove the bucky
shell, and then fix the Note: Before install the bucky, confirm the chest radiography
Bucky on the mounting
chest radiography frame
frame direction, According to the actual situation, bucky
block with hexangular
set screws has different direction. detector's socket should always be facing the operating table.
According to the actual
situation, bucky detector's
socket should always be
facing the operating table
Picture 1 Picture 2
Steps :
Put the bucky's shell
2. After finish put into the filter grid, Put the bucky's shell on and
Loosen the filter grid fixed
lock the screw.
block, put into the filter grid,
Picture 1 electromagnet and encoder Picture 2 1. Lock the counterweight sealing plate, then lock the electromagnet and
cables into the cable slot, and
encoder cables into the cable slot, and lock the screw, as picture 1.
lock the screw
2. Fix the electromagnet cable to the slot with the cable clip, as picture 2.
Tied up the electromagnet
cable tie
3. Connect the chest radiography frame’s lifting motor’s cable, and the
Connect the chest
Connect the Picture3 chest radiography frame’s lifting electromagnet’s cable, and the chest
radiography frame’s
chest radiography frame’s lifting potentiometer’s cable, as the picture 1.
lifting motor’s cables
radiography frame’s
cables
lifting electromagnet’s
4. Connect the controller cable of the Bucky, as picture 3.
Controller cable
connection
Connect the
Requirments:
chest
potentiometer’s cable
radiography frame’s
1. The cable should be straightened and neat.
lifting
2. Ensure that all cable terminals are inserted in place.
Picture 1
Steps :
1. Remove the sealing plate and limit block on one side of
Remove the sealing plate and limit
2. Loosen the filter grid fixed block, put into the filter grid,
and confirm the position is centered, then lock the fixed
block, as picture 2,3.
Picture 2 Loosen the filter grid fixed block,
put into the filter grid, and confirm
Filter grids’ positioning Note: There are positioning reference holes around the
the position is centered, then lock
the fixed block.
reference holes
chest installation frame.
Note: There are positioning
reference holes around the chest
Picture 3
Requirments:
installation frame
1. Ensure that the filter grid and the detector are aligned.
Picture1
Steps :
1. Ensure the filter grid is installed completed,
put the bed panel back, and install back the
sealing plate and limit block.
Picture 2 Picture 3
Requirments:
Low High Ensure the filter grid is installed
position Position
aging test
completed, put the bed panel back,
1. During the process of disassembly and assembly,
and install back the sealing plate and pay attention to protect the bed board to prevent
limit block
collision.
Auto tracing mode calibrate steps:
Towards the tube to bucky Stand, move the tube to lowest Position, and move the bucky stand to same level,
long press “low position” button for 3 seconds.
Auto tracing mode calibrate steps:
Move the tube to highest Position, and move the bucky stand to same level,
long press “high position” button for 3 seconds.
Picture1
Using the Ribbon to
tied up the cables in
here
Wrap the High voltage Steps :
10cm cable 、
screen serial cable 、
1. Tie up the cables, as picture 1.
collimator cable with
bucket-type end straps
3. Wrap all the cables that come out from the bed, chest
radioghy frame, and put them all in order.
10cm
Wrap the cables
with
wrapping band
Thank You !