Professional Documents
Culture Documents
Hex Bolts Grade A B Metric
Hex Bolts Grade A B Metric
U H E T
METRIC
R F
L
ISO 4014 F G K
Width WrenchWidth Across Across ing Flats Corners Height Max 3.2 4 5 5.5 7 8 10 13 16** 18** 21** 24 30 36 Min 3.02 3.82 4.82 5.32 6.78 7.78 9.78 12.73 15.73 17.73 20.67 23.67 29.67 35.38 Min 3.41 4.32 5.45 6.01 7.66 8.79 11.05 14.38 17.77 20.03 23.36 26.75 33.53 39.98 Min 0.68 0.89 1.1 1.31 1.87 2.35 2.7 3.61 4.35 5.12 6.03 6.87 8.6 10.35
Max 0.25 0.25 0.25 0.4 0.4 0.5 0.5 0.6 0.6 0.6 0.6 0.8 0.8 0.8
Min 0.1 0.1 0.1 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.2 0.2 0.2
Max 2 2.6 3.1 3.6 4.7 5.7 6.8 9.2 11.2 13.7 15.7 17.7 22.4 26.4
Min 2.27 3.07 4.07 4.57 5.88 6.88 8.88 11.63 14.63 16.63 19.37 22.49 28.19 33.61
0.35 0.4 0.45 0.5 0.7 0.8 1 1.25 1.5 1.75 2 2 2.5 3
9 10 11 12 14 16 18 22 26 30 34 38 46 54
40 44 52 60 73*
Tolerance on Length
12-16mm: 0.35
35-50mm: 0.5
55-80mm: 0.6
130-150mm: 0.8
*For nominal lengths over 200mm. **DIN 931 spec for maximum width across flats on these three diameters are 17, 19 & 22 mm, respectively.
ISO 4014 K
Width WrenchWidth Across ing Across Flats Corners Height Max 24 30 36 46 55 65 75 85 95 Min 23.16 29.16 35 45 53.8 63.1 73.1 82.8 92.8 Min 26.17 32.95 39.55 50.85 60.79 71.3 82.6 93.56 104.86 Min 6.8 8.51 10.26 12.8 15.46 17.91 20.71 24.15 27.65
Min 0.2 0.2 0.2 0.2 0.2 0.3 0.3 0.3 0.3
Max 3 4 4 6 6 8 10 12 13
44 52 60 72 84 96 108 -
Tolerance on Length
110-120mm: 1.75
200-240mm: 2.3
260-300mm: 2.6
320-400mm: 2.85
420-500mm: 3.15
METRIC
8.8
Material
Heat Treatment Core Hardness Surface Hardness Proof Load Tensile Strength Elongation Plating
Class 8.8 bolts shall be heat treated by quenching in a liquid medium from above the transformation temperature and reheating to a tempering temperature of 425C. For diameters less than or equal to 16mm: Rockwell C22 - 32 (Vickers HV 250 - 320) For diameters greater than 16mm: Rockwell C23 - 34 (Vickers HV 255 - 335) Shall not be more than 30 Vickers points above the measured core hardness on the product For diameters less than or equal to 16mm: 640 N/mm2 minimum For diameters greater than 16mm: 660 N/mm2 minimum For diameters less than or equal to 16mm: 800 N/mm2 minimum For diameters greater than 16mm: 830 N/mm2 minimum 12% minimum See Appendix-A for plating information
10.9 10.9
Material
Heat Treatment Core Hardness Surface Hardness Proof Load Tensile Strength Elongation Plating
Class 10.9 bolts shall be heat treated by quenching in oil from above the transformation temperature and reheating to a tempering temperature of 425C. Rockwell C32 - 39 (Vickers HV 320 - 380) Shall not be more than 30 Vickers points above the measured core hardness on the product 940 N/mm2 minimum 1040 N/mm2 minimum 9% minimum See Appendix-A for plating information