Professional Documents
Culture Documents
Readmebolol
Readmebolol
TXT File
Notes for MINI-LINK Craft 2.20.2 Upgrade Release.
(c) Ericsson AB 2003-2013. All Rights Reserved.
This file contains the latest information about this upgrade version of
MINI-LINK Craft.
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
SUPPORTED MINI-LINK RELEASES
MINI-LINK Craft 2.20.2 supports
- MINI-LINK TN 3.2 - 5.0
- MINI-LINK CN 500 1.1 - 2.2
- MINI-LINK CN 210 1.0 - 1.2
- MINI-LINK CN 510 1.0 - 1.2
- MINI-LINK PT 2010 1.1 - 1.2
- MINI-LINK LH 1.1 - 1.2
- MINI-LINK SP 110 1.2 - 1.3
- MINI-LINK SP 210 1.2 - 1.5
- MINI-LINK SP 310 1.2 - 1.5
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
LICENSING CONDITIONS
Provision for the use of this software package, including programs and related
documents, is that you read and accept the licensing conditions shown during
the installation of MINI-LINK Craft upgrade.
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
MINI-LINK Service Software (MSS) and included products are under export
control. All export and re-export shall be in accordance with national and
international export control regulations. An export license application has
been approved.
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
THIRD PARTY SOFTWARE PRODUCTS
see MINI-LINK Craft\DISTRIBUTION COPYRIGHT\readme.txt
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
INSTALLATION OF MINI-LINK Craft 2.20.2 UPGRADE
Before you start:
- Make sure that one of the previous MINI-LINK Craft 2.0 - 2.20.1 versions are
-
installed.
Make sure that administrative rights are set.
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
KNOWN BUGS AND LIMITATIONs for MINI-LINK CRAFT
1. Configuration Time for MMU units
In MINI-LINK TN releases 3.3.1 to 3.3.2, MINI-LINK Craft may freeze when
setting up protection on newly inserted MMU units. This operation normally
takes a few minutes to complete. Workaround is to re-start MINI-LINK Craft
and setup protection once again after 5 minutes.
2. Basic NE Page: Change of IP Address
When changing the IP address for the node and pressing reconnect, it may
take up to 15 minutes before a new log-in window is displayed. The work
around is to close MINI-LINK Craft after the change of IP address. Restart
MINI-LINK Craft and perform a new log-in on the node.
3. Script error when performing SW upgrade
When upgrading MINI-LINK node, containing MINI-LINK TN 4.2 SW or older SW,
with MINI-LINK TN 4.2FP SW or newer SW, then a script error will occur. The
script error is displayed at restart of the NPU unit. The script error does
not cause any problem for the SW upgrade.
4. Silent installation of MINI-LINK Craft
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
TECHNICAL SUPPORT
If you have a technical question or have encountered a problem with this
software, please contact your local Ericsson representative.
When contacting your local Ericsson representative, please provide the
following information for the fastest possible service:
- Product serial number
- Your name, company name, and phone number
- Product name and version number
- Type and version of operating system, including service packs
- Complete description of the problem, including steps to reproduce it
- Exact wording of any messages displayed when you encountered the problem
- Steps taken to resolve the problem
- All previous correspondence with Ericsson in this matter
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
No. 19000 - CXP 902 0016/1
Rev AK
Date 2013-02-15
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *