Professional Documents
Culture Documents
Tips CRT TV Repair
Tips CRT TV Repair
Very strong red content in the picture, sometimes the fault would clear with the
strong red content fading until the correct greyscale was achieved
After much searching around i found the problem. There was a very small crack in the solder
at RH23, this is a 2K4 surface mounted resistor located at the back of the tube base.
Resoldering both sides of it cured the fault
(Sparky)
Jvc TV Model: C-V14EKS/B/W (Onwa Chassis)
No Red
I was hoping the nvm had become corrupt and turned the red drive down but it was fine (To
enter service mode press and hold vol up and vol down on the front panel and switch set on).
Thankfully ZD405 (8V2) had expired (almost s/c) and removed the red
(Andy Doswell)
Sanyo Video Model: VHR776E
Dead
Check and replace PR512 (which is located towards the front right hand side)
(T.t.r.s. - Tim)
Nikkai TV Model: BABY 10
No / int luminance
Poor contacts within the service switch
(John)
Sony TV (AE1 Chassis)
Unit not working, no FL display, ticking from PSU, head drum twitching
Electrolytic cap in PSU primary dried up (47uF, 50v)
(Anonymous)
Ideal/Slx TV Model: IDTV28T/IDTV28N/SLX28T2/28N (SM2 Chassis)
Procedure to exit child lock with pin unknown / "locked" displayed on screen
Switch set on, press menu, select feature and press enter, select parental lock and press enter,
then enter the code 0, 7, 1, 1 twice, the lock should now have cleared
(Josh)
Fermendi TV (F19 Chassis)
Dead no click, Q502, Q601, Q602 shorted and blown fuse 602
Change all the above parts and also check R647, C512, C525, D607, D608, D609, D610,
D622, VDR601 off primary side of T605. I`ve also found T605 bad too. ToughDog, Sony has
Dead, good tip that I always use to save changed parts after replacing Q502, Q601,
Q602 and blown fuse 602
I hook up 100 watt light bulb across fuse conection, then turn on tv, if light is very bright you
still have a short. You saved the parts you changed, light should be dim and or blinks
(Dwayne)
Sony TV Model: KV27TS20
Dim display
Check capacitor CP41 (220uF, 10v)
(Tom)
Panasonic Video Model: NV-L20
Poor playback and recording (looks like poor heads). Also shows as interference
when playback appears
Check all electrolytics in secondary of switch mode power supply
(Ray)
Hitachi Video Model: VTM640
Dead, after replacing ic601 (STR54041) and Q601 (BC637) standby led blinks red
twice, then blank, no HV
Replace fuse p801 (ICPN15 - 0.6A 50V, TO92)
(Anonymous)
Amstrad Video Model: DD8900
Bottom deck fails to load tape when pressing play/record. Sounds like loading
motor is labouring when the pinch roller engages capstan shaft
The loading may complete if black pulley wheel on motor drive is 'helped'. Look for stiff
linkages before suspecting Motor
(Anonymous)
Tatung TV (F Series Chassis)
Starts up with black raster, then shuts down with LED blinking 4 times
This is the micro telling you that the auto grey-scaling procedure has failed. Change resistors
R909, R913 & R922 (180k, 1%) on crt base PCB. You will probably find that all these have
gone high
(Rob Hancock)
Matsui TV Model: 1408T
Locked out by incorrect pin number being used - and Dixon's want 25 to do this!
1: Press standby on remote control to switch TV on
2: Press volume minus button on set front, while pressing 7 on remote control for at least two
seconds, until 'OK' appears in the middle of the screen
Thanks to my son who has no TV training at all!!
(James)
Panasonic TV Model: TX28W3 (EURO 1 Chassis)
No raster, only heard a pip from speakers that went after a few seconds
C623 and R628 changed
(Nima)
Grundig TV Model: ST70-460 (CUC4635 Chassis)
Dry joint on R636, vertically mounted 4.7 ohm wirewound in sw mode circuit
(Peter Nutkins)
Nei TV Model: 2031TX
No Power
R802 open circuit. Unknown device (poss. Thermistor). Replaced with 15K, 2Watt
(Anonymous)
Sony TV Model: KV-2565MT (SCC-E64P Chassis)
Dead
This was found to be due to the STR58041 chip
(Anonymous)
Philips TV Model: GR2.4AA (GR2.4AA Chassis)
Sound mutes for too long when changing stations (up to 30 secs)
The MAB8441-T005 was faulty (no longer available)
(Anonymous)
Thorn Video Model: VR414LVA
Chopper secondary voltage (115V) was way too high (around 220V)
C615, Q605, Q606 and R308 had all died, The value of C607 (47uF) was out of range. Note:
This set is equivalent to the Princess GT-1412
(Armando Valente)
Sony TV Model: KV-HF14M80 (BG-3S SSC-U21F Chassis)
divider network (C306 & C307 in series, centre of which goes to the protect circuit), it is hard
to get to being right by the line output transistor
(Kind Regards - LB)
Beko TV Model: 14.2
The +Ub voltage (+140V) was not present, fault in switching power supply
Transistor T601 (SK2545) had failed, replace/check resistor R602 (1Meg ohm) in switch
control circuit, also if T601 is s/c the control chip TDA16846 will also be damaged
(Gordon w.Cox)
Sony TV Model: KV25K5U (FE1/FE1A Chassis)
Noise from speakers / center speaker even with the volume set at minimum
Replace IC1300 (BA4558F 8pin smd) and IC1302 (TDA7480) which are both located on the
central speaker amplifier plug-in PCB
(J.C.)
Jvc Video Model: HRJ205
Set stays in standby intermittantly or will int switch off to standby also brightness
and contrast slightly low
Resolder all joints in the power supply (very small dry joints that need a microscope to find !)
also check / replace replace capacitors C109 and C110 and check condition of other psu caps.
(Pappy)
Start up problems
Replace CB712 and CB726 in the power supply. Both are same value (4.7uF, 50V)
(Anonymous)
Goldstar TV Model: 20A80
No picture, FR406 ok
Check the video output amplifier stage for failure
(Zubair Almas)
Panasonic Video Model: NV870 (D1 Mechanism)
Noisy FM audio
Add a 0.01uF 50v ceramic capacitor between pin 9 of IC4509 and ground (only applies to
units with serial numbers prior to D5K)
(Anonymous)
Panasonic Video Model: NV870 (D1 Mechanism)
Picture is folded over at the top and curled at the top left hand side
Replace C559 and C560
(Anonymous)
Sony TV Model: KV1412
Noisy picture
Replace relay RY481 on S2 board
(Nigel Burton)
Sony TV Model: KV1412
Set reverts to standby mode when switched on, because IC003 does not reset
correctly
Replace IC003 on A board, IC type CX523013P
(Nigel Burton)
Medion TV Model: MD7103VTS (11AK18 Chassis)
Power LED and Sound OK. EHT Voltage for 1 Second after switching on via
Remote Control
Replace vertical deflection circuit IC605 (TDA8361) - dont forget to apply Heat transfer
compound !!
(Rainer)
Sony TV Model: KV28WS3 (AE3 Chassis)
At switch on a strange sound comes and goes for a few seconds, no sound and
vision
Check R622, Q624 and T639
(Anonymous)
Grundig TV (CUC5310 Chassis)
Randomly switching to scart input when the programme output from the tuner
should be displayed
This is now becoming a common problem, the cause being the painter chip IC7064 which is
located on the small signals panel, there are 8 different versions but only 3 common versions
(Anonymous)
Schneider TV Model: DTV2
Totally dead except for a few rapid flashes from the green led at switch on
C811 a 100uF, 16v capacitor in the power supply was the cause, it is located next to the
chopper transistor's heatsink. This is the same TV/Video as the Goodmans TVC14VP
(Rob Marshall)
Panasonic Video Model: NV-HD675 (Z-Mech Chassis)
After switching on, no longer able to switch-off with remote control, standby light
comes on with sound muted. (Original remote control: RM-700)
Opto-coupler PC113 faulty
(Esohe)
Ge TV Model: PTK195AA (PTK195 Chassis)
Works fine for 10 or 15 min. (or sometimes 1 or 2 days) then bows from top and
loses convergence
Replace the STK730-130, located on small board above the convergence module
(Clonch tv)
Lenco TV Model: 14P1MNA
Standby only
Check R101 (4.7ohm), TR102 (C6180) and C126 (47uF, 16V)
(Akalipt)
Sony TV Model: KV-M1400 (BE2A Chassis)
No sound, picture ok
When shifting up the channel frequency using the fine tuning, a very weak sound could be
heard. Replaced the sound IF demodulator chip U2829B(IC2110)
(Rui Loureiro - Portugal)
No sound
IC901 (TDA4935) blown due to excessive supply voltage, capacitors C619, C623, C810,
C600, C601, C859 defective. Also verify R822
(Jeroni Paul)
Jvc TV Model: AV25S1EK
Field collapse
Resolder TDA3654 as joints appear good but on application of soldering iron show to be dry
(Pj)
Mitsubishi TV Model: CS40503
Led changes from green to red, fails to start up, no EHT but secondary voltages in
psu ok (150V ok)
Check Q601 and Q606, these are Q600 LOPT drivers, there should be 2V P-P on base of
Q606 and 150V on collector of Q601, replace Q606 with a BC182 (check pinout)
(Steve May)
Matsui TV Model: 25M3
No vertical deflection
R615 open (0.13 ohm 1/2W). Also resoldered many bad solder joints
(Jeroni Paul)
Jvc Video Model: HRD750
Poor tape transport, tape is crumpled, upper or lower side gets rippled
Replace the capstan roller, if the tape transport is still not smooth check the guidepole
(between the audio/control head and the capstan), tape must touch border-ring. Adjust the
audio head position (screws marked A and T)
(Anonymous)
Bluesky TV Model: TDX-70 (11AK19 Chassis)
HT low / missing
Q608 (BU2508) dead (short-circuited). Needed replacement. That's all...
(Anonymous)
Panasonic TV Model: TC2195DRS (Z3T Chassis)
SMPS noise. Low volt and high current on Usyst, no screen or sound
FBT TLF15606F
(Anonymous)
Irradio TV Model: MC-FBC-006
between both motherboards, especialy the one very close to plastic frame
(Jose Carlos Pinto - Oporto)
Toshiba TV Model: 2505DB
Set starts, horizontal and vertical deflection work, HT ok, crt heaters ok, but no
sound or picture
I turned the G2 voltage up and noticed a white screen with flyback lines, frame ok. I detected
two badly soldered double diode rectifiers in the secondary part of the power supply ! I
checked all other joints, and everything was ok !! success
(Anonymous)
Hitachi TV Model: C1714T
Frame collapse, causing set to go dead, also can cause the regulator transistor, to go
s/c. BUT12AF. H.T. unstable
Check R951 (39K) goes high, in this case 65K, causing HT to go high
(G3xxr)
Philips TV (GR2.1 AA Chassis)
Poor picture quality from CVBS EXT1 and EXT3. Low intensity high saturation.
Loss of sync. Shock and temp dependent
Dry joints on SMD resistors 3014 and 3019 on IF/Sound module other side of encapsulated
TDA2549
(Choc's maker.)
Sony TV Model: KV-A2923
Attempts to start up. When main switch is pushed ON, relay coupling and
decoupling (on-off, on-off)
Replace: C805 (47uF, 50V) next to the TDA4605 and C801 (1uF, 50V)
(Zoran)
Goldstar TV Model: CBT-9745 (PC91A Chassis)
TV dead. PSU ok, led lit. When button pushed on remote the LED goes out but set
does not start (Missing HF voltage)
Replace: C417 (1uF, 250V) Elko for HF oscill. (next to HF trafo)
(Zoran)
Philips TV (FL1.1AA Chassis)
Frame Collapse
Replace IC401 (TDA8177F) and resistors R325, R326, R327
(Jim Ross)
Matsui TV-Vid Combi Model: TVR185
Int sound
Check voltage on sound IC, if it drops with high volume change C620 (1000uF, 25 vdc)
(Arl)
Sharp TV Model: 66GF-63H
No picture no sound timer light flash 44 fast 45 then 5 times then 5 times
Replace power block part # 1-468-510-11
(Mervin)
Toshiba TV Model: 198X6M
Black screen from tuner but OSD (menus and channel no.), teletext and sound work
normally
Q500 and Q504 blown, replacement cured fault. Removing R508 also restored picture. Fault
puts TDA8840 in RGB insertion mode continuously, so separated RGB input might still work
(Joe Kelleher)
No vertical deflection
If resistor R445 (1ohm) has gone open circuit this may cause IC550 (LA783x) to also fail.
Replaced both IC550 and R445
(Daniel)
Sony TV (FE-1 Chassis)
Procedure to display past error codes and the number of times they have occured
(particulary useful for ongoing intermittent faults)
Enter the standby mode then press the on-screen display button (i+), 5, volume down, and
finally the tv button. Note: the error count can be reset by pressing 8 then 0 on the remote
control
(Josh)
Sony TV (FE-1 Chassis)
Intermittently displays bright red/green/blue raster then shuts down with led
flashing 2, 4 or 5 times
Amazingly this was due to the CRT being faulty !
(Josh)
Philips TV Model: 33SL5796/16B (FL 1.0 Chassis)
Snowy picture specially in VHF band. After about 5 minutes, picture snowy in all
bands. About 10 minutes after switching on, no picture nor sound, just snow on the
screen
Replaced the TUNER/IF. Original code was FQ816ME which is no longer in production.
Replacement code is FQ916DME
(Rui Loureiro - Portugal)
Sony TV Model: KV-21RXR1
Narrow Picture
After resoldering joints in the line output stage, check R629 (27ohms, 1/2w) safety resistor to
E/W FET, also o/c capacitor C630 (0.47, 250volts). According to the schematic R629 is 2.7
ohms
(Conrad626)
Philips TV Model: 14PV220 (EPSILON 2001 Chassis)
Dead (Totally)
SMPS Chopper IC 7310 (MC44608 P75). I had no output from pin 5 with start up voltage pin
8 OK at 290V. If start up missing check start up resistor 3335 (1K). The only source I found
for IC 7310 was Philips direct, part number 9322-143-51682, cost ~ 10
(Paul van gelder)
Philips TV Model: 21GR2751 (G90B Chassis)
Stereo set with no sound off air, maximum volume produces low hiss, some sound
possible if station is detuned slightly. Sound via SCART is ok
Replace IC U2829B on audion panel
(Bill)
Nordmende TV Model: GALAXY 55 (ICC8 Chassis)
Dull picture
Replace (TT33) on tube base
(B goan)
Nordmende TV Model: GALAXY 55 (ICC8 Chassis)
Tape loading carrage is very loose and sloppy will not load and eject tape properly
Mode switch is faulty, out of alignment or has a bad connection back to the PCB. This switch
is located underneath the tape drive mechanism
(Anonymous)
Samsung TV Model: CB7230WT
After replacing the line output transformer, the following sympton was displayed.
Display flashing standby light and stereo II
Short s23 and s24 briefly, which will put the set into service mode. Option 1 should read 010
this applies only to the 25FL and 29FL. Option 2 should be 001 for sets with text and 004 for
sets without text
(John Carey)
Jvc TV Model: AV28WZ2
Blank raster
Replace defective TDA6111Q for Red, Blue and green
(Rens van der enden)
Thomson TV Model: 28VK-44E
Stuck in standby but tripping, not the usual nvm problem and nothing s/c
Check and replace C804 (1uF, 25V), C806, C807 (100uF/50V) in supply. Use 105 degrees
cap. types
(Rob's TV-service - Holland)
Philips TV Model: 25FL1760 (FL1 Chassis)
Set tries to go to stereo as indicated by the on screen display, but most of the time it
is stuck in mono, when in stereo the right channel was hissing
Replace the TDA8415 on the stereo decoder board, confirm this buy putting multimeter on
pin 7 and 8, they should have a voltage of 3.2 volts
(Cannny)
Philips TV Model: 29FL1770 or 25FL1760 (FL1 Chassis)
No pictures or sound
Disconnect the P1 and P2 plugs on the right hand side board. L.o.p.t. side. If the set now starts
up then change all sound output IC's
(Cannny)
Philips TV Model: 29FL1770 or 25FL1760 (FL1 Chassis)
When selecting a channel it locks in initially but will then go off tune (as if the
voltage tuning had varied)
Replaced the TDA i.c. in the tuner i.f. section. (tried the capacitors first of course).
(Cannny)
Philips TV Model: 29FL1770 or 25FL1760 (FL1.0 Chassis)
Lights flashing at the front, if carefully interpreted they point to the primary of the
power supply
Replaced 2SB 3795B chopper transistor, heated the heatsink with a hair dryer and it started
right up, weird as the transistor was reading fine
(Cannny)
Decca TV Model: D20RDE6 (D Series Chassis)
Dead set
Found the IRD shorted
(Anonymous)
Telefunken TV Model: Palcolor S540C (ICC9 Chassis)
At switch on front l.e.d turns green, blinks twice then set returns to standby. All h.t
voltages rise, then fall away as set goes into standby
33 ohm resistor feeding standby 5V reg was high (8 ohms - not shown cct diagram), in my
case D605 on the 45 volt supply from the LOPT was faulty, although it measured o.k
(Supadan)
Thomson TV (TX807 Chassis)
(H)VTU Tension de sintonia 99v pero en el zener DH01 (ZTK33A) hay 22v.
Sustituir zener 33v (ZTK33A)
(Eisi)
Hitachi TV Model: C2146TN
No colour
Dead
Found Q802 (C4927) short, replace with same type as no other types last
(Seles)
Panasonic TV Model: TX-2470
Bright red raster with flyback lines,shutting down after about 30 seconds with
squealing from power supply
The fault was due to the supply choke to the red output stage on the tube base panel being
O/C, I can only assume the shut down was due to excessive beam current, a long soak test
proved all was now ok
(Thunderdunc)
Philips TV Model: 20PT3742
When switching to STBY raster remains and buzz noise is heared from the speakers
Cause: +B voltage (103 V) does not switch-off. Remedy: Replace defective C541
(Vitaly)
Schneider TV Model: STV515
Appears to be stuck in standby with the front led flashing and the h.t. at about half
the correct voltage
This set led me a merry dance until i discovered the set was actually in the child lock mode !!
The problem was solved once this was disabled using the remote control
(Josh)
Sharp TV Model: 51DT-25H
NVM modification / symptoms such as no video, tuning drift & reduced height
from cold
Fit 2 zener diodes (part no. RH-EX0404BM22) in positions D510 and D511, fit coil (part no.
VP-CF120K0000) in place of link J122 and fit zener diode (part no. RH-EX0412BMZZ) in
position D403
(Josh)
Beko TV Model: 12.8
The +Ub voltage (+118V) was not present, fault in switching power supply
Transistor T901 (SK2545 or P3NB60FP) had failed. Replace it and check C908 (22uF, 35V)
replace it with 22uF, 50V. Also C912 (1uF, 25V) replace it with 1uF, 50V and D906 (1N4148)
always replace it with 1N4948T
(Jo)
Philips PLASMA TV Model: 42FD9954 (S FM24 Chassis)
No audio
Check and replace ic101 with STV2246C and check and replace c135 (100uF, 16V) replace it
with a 220uF, 50V. Also check and replace C308 (470uF, 16V) replace it with a 470uF, 50V
(Jo)
Beko TV Model: 12.8
VCR is locked out, no sound, noise picture and front panel buttons do not work.
NVRAM has been lost
Access the NVRAM menu. On remote hold A-Dub button for 10secs, VCR display will read
TEST, then hold the menu button until the NVRAM menu is displayed on screen. I do not
know the codes for this model, if anyone knows them please pass them on!
(James)
Philips TV Model: 24PW6005 (A10E Chassis)
Dead, fuse ok
Replace Q701 (P3NA80FI) with a P4NB80FI-mbr. Check Q702 (BC338). Replace R703
(5,6E, 5W), all components in supply. Check print for poor contacts
(Rob's tv-service - Holland)
Panasonic Video (K Deck Chassis)
Unable to switch on with remote and no LED display at the front of set
Due to STBY 5v missing. Checked and found the 5v reg/reset IC002. (L78LR05D) was s/c,
replace the IC to clear the fault
(Anonymous)
Philips TV Model: 25PT4103 (L6.2 Chassis)
Sleep timer box on screen, remote & front buttons not working
Changed the EEPROM IC847 (24C04)
(Urhoej)
Akura TV Model: AP2821-S
Dead
Replace RP05 (1 meg, 1/4 watt)
(Darren)
Toshiba TV Model: 2573
Stuck in standby.
Screen blanked out,with 4 coloured lines two thirds of the way down from the top
of pic. Sound OK
R704 (100 ohm resistor) connected to pin 6 of the frame output chip was o/c
(Anonymous)
Philips TV Model: 28PW6332/05
Loud bang internally, then completely dead. Plug fuse ok. Set about 4 years old
Internal 4A fuse blown. Bang was 330pF cap 2540 across PSU MOSFET exploding, suspect
went s/c. Diodes 6513 & 6511 cracked and s/c. Replaced C2540. Could not get diode
1N5062/BYW55 rep, so replaced all 4 diodes with BY399. PSU MOSFET removed and
checked,ok. Voila
(Andrew Wilson)
Panasonic TV-Vid Combi Model: TX-14/21GV1
Dead Set
No surround sound
As Mark said in a fault on the Euro 4 chassis, Replace the TDA2030.
On this model there are three TDA2030 s. If you have to replace any also as a matter of
course replace the two regulators Q2701 and Q2702 or the chances are the TDA s wont last
long
(Anonymous)
Sony TV (FE-1 Chassis)
No sound
This may be remedied by entering TT24 in the service mode, if fault persists Q202
(2SC2412K) could be leaky
(Josh)
Sony TV (FE-1 Chassis)
Pressing the screen format button displays wide, smart, zoom and 4:3 modes but
settings have no effect on picure
Enter TT35 in the service mode to select a 4:3 CRT
(Josh)
Sony TV (FE-1 Chassis)
Tv stays in stand-by when the power is swiched on. No response from the remote
or any button on the set
F on top righthand of screen then loss of geometery data and int shutdown, unable
to restart but when try do so set cuts out
Painter IC failure, A small 100 leg device a joy to change if you have the right gear ! Ref
IC7064 also updated software on new IC
(Christv)
Samsung TV Model: CT566 (K51A Chassis)
No power
Voltage not changing on pin 18 IC901 (SZM-368ET2)
(Anonymous)
Nokia TV Model: SP71L1
Dark picture
Replace RL03
(Kostas - Greece)
Samsung TV Model: CB7230WT
OSD appears as one big horizontal line with wrong colours and noise (looks like no
Tv turns on automatically. Power supply works well, +5V present but seems that
CPU (7700) does not (no standby mode), no remote or control on the front of the
set
After replacing CPU (TMP47C434) and crystal 1770 (4.0MHz) both control worked
intermittently. Replacing transistor 7674 (BC548) solved the problem
(Mladen - Visegrad)
Amstrad Video Model: DD8901 (47014601 Chassis)
E/W failure
Replace CD22 (470nF) and TV06 (BD680)
(Anonymous)
Jvc Video Model: HRJ610
Dead
Transistor Q31 in PSU leaky
(K. Tait)
Panasonic TV Model: TX-32PK3
Initial rustle of high voltage then nothing, goes to standby, same with remote or
front panel controls
R12 burnt out (0.22ohms), replacing this plus the IC01 vertical IC (TDA8177) got set
working. NB: also check D01 for shorts
(Ben)
Toshiba TV Model: 219T9B
Sound crackles and whistles a short time after switch-on. Gets worse as set warms
up
Solder all links and components that have unpainted copper areas around component legs on
upper side of main board near to the audio processing I.C. The same applies to the
components near the microprocessor
(Anonymous)
Toshiba TV Model: 145R7B
Dead
No tuning
Check R3703 for o/c and R3702. Also in CTT-H AA chassis, then R3602
(Hanske)
Philips TV Model: 37TA1070 (CTT-H AA Chassis)
No tuning voltage on tuner. Goes for: Philips and Magnavox versions. Also the
Radiotone TV386VT-SCART which is the same
Resistor 3602 (8Kohm) broken. It is in the 95Volts line providing 33V for tuning circuit. This
chassis uses the same processor as the GR1-AX which also might have the same problem. In
that case resistor 3702 is to blame
(Hanske)
Philips TV (CP110 Chassis)
Operating fine (good picture, sound and control) but sometimes sharp sounds
coming from the set (not via audio), sounding like the LOPT but more loud, sharp
and variable (15 Khz)
The long coil next to the LOPT was resonating/generating sound (not the LOPT itself), solved
by cleaning the top and putting a bubble of silicone kit on it, and after temporarily removing
the coil from the pcb fixating a ty-wrap strongly around the bottom increasing the magnetferrite contact-pressure and stiffness of plastic support construction
(Bartronics)
Philips TV (L6.2 Chassis)
No sound, no picture and the power supply makes a loud and low tone chirping
noise
Replace shorted Capacitor 2912 (2n2, 2kV) on the deflection module. Note that 2912 is hard
to find. It should be blue. If it's brown it's bust
(Anonymous)
Philips TV Model: 27CE4599-33R (2B Chassis)
No sound
R829 (4.7 ohm) o/c
(Anonymous)
Fidelity TV Model: CTV3221
Dead
Check all high value resistors in primary of the p.s.u. If the fuse is blown, expect to replace I1,
Q1 and R1 as well, Probably best to do all three and check the rectifier diodes
(Anonymous)
Sony TV Model: KV2032
Intermittent functions
Check for dry joints on mode switch and clean off any grease inside the switch
(Vincenzo)
Telefunken TV (TX92F Chassis)
Keeps on burning the surge resistor 280ohm 5W in series with the chopper
transformer
Replace the chopper transfomer it has a short either on the primary or secondary side
(Prince)
Philips TV Model: 29PT785C (G88 Chassis)
The set goes into protection and tries to restart. The tube shows no horizontal lines
After disconnecting the horizontal plug the +148V and CRT high voltage remained stable.
The small pcb on the tube (scan coils with 5 or 6 pins) was dry jointed at copperside
(Anonymous)
Sharp TV Model: DV3760H
At switch on set starts-up with lots of sparks inside CRT socket, then switches to
standby
Replace FBT - HR 8317. There is a repair kit available from Thompson for this chassis, which
includes a new loptx, tuning caps and a couple of coils. There are also some surface mount
resistor value changes. It's Pt. no: 35175720
(Andy Doswell)
Panasonic TV Model: TX33AK10 (EURO 5 Chassis)
No secondary supplies
Check / replace C418 (100uF, 25v), C489 (100uF, 40v), C425 (1uF, 400v), posistor PTC401,
R422 (5.6ohms, 1w) and the chopper transformer
(Anonymous)
Goldstar TV-Vid Combi Model: KY14V30
Red led blinks on / off, TV does not turn via power button and/or remote but after
20 minutes or so it turns on and works fine
Replace R902, R901, R905, R903, R900A, Q902, and possibly the two (one small and one
large) capacitors in the section labeled as the power supply. The board will be black under the
components that are bad. Q902 is an NPN transistor and is hard to find.
(Eliot)
Sony TV Model: KV28WS2U
Dead set, with 300v across smoothing (takes a very long time to discharge, watch
out!)
Check RP06 (3.9M ohm) for O/C, the one I had had nothing else gone
(Anonymous)
Firstline TV Model: 1433GR
No picture, no OSD
Zener diode D219 (12V) shorted. Check capacitors C608, C606, C617, C619, C411 and
resistor R256 (39 ohm, 1W). Unreg. voltage to R256 should be 16-17V with no change when
warm
(Jeroni Paul)
Philips TV Model: 28ML8805-16B (FL1.6AA Chassis)
Dead
Fuse open (3.15A), transistor 7216 (ON4827 = BUT12AF) shorted and solder joint of SMD
resistor 3305 (11K) cracked (located on PS control board)
(Jeroni Paul)
Philips TV Model: 28ML8805-16B (FL1.6AA Chassis)
When inserting tape, tape goes in, get a motor whirring noise, and tape ejects again
with an "F02" or "F04" error. Closer examination shows that tape seating correctly,
but tape not being fed out to the head
Cause was the motor powering the main mechanical feed/load and eject gear, underside of
main front right of central chasis. Small plastic part on motor spindle under gear had split, so
slipping. Secured part and gear to spindle with super glue! OK now!
(Ian Harrison)
Bush TV (11AK19 Chassis)
Poor picture
Faulty C329 (4.7uF)
(Vlado - Macedonia)
Philips TV (2BS Chassis)
No E-W Correction
Replace TR7467
(Vlado - Macedonia)
Sharp TV Model: (21B Chassis)
No UHF Band
Check Q212
(Vlado - Macedonia)
Goldstar TV (PC12A Chassis)
Dead
Replace D401
(Vlado - Macedonia)
Goodmans TV Model: GTV69WZDT
Set dead
Replace switch mode i.c IC106 (MC44608P40
(Fairfield Televisions)
Samsung TV-Vid Combi Model: TVP-3350IS (SCV11C Chassis)
Stuck in stand-by
X501 4MHz Xtal
(Anonymous)
Hitachi TV Model: C2867TN
Dead psu
C110 defective in psu (47uF, 25V) - Resevoir cap for ic
(Anonymous)
Bush TV Model: 2866NTX/SM2
This set was dead apart from a hissing sound from the speaker, no standby led
5 volt regulator on front panel had 13 volt input but only 1 volt output, Replacement cured the
fault
(Brian odonnell)
Panasonic Monitor Model: E110 (NA Chassis)
Over a short period of time the convergence of the picture gets steadily worse.
Eventually it is so bad that even the teletext shows double or triple images when
they are made up of a combination of colours. Pure colours: Red, Green or Blue are
OK.
The Tube must be replaced. Apparantly this is a known problem to Panasonic, especially on
32" tubes. It has been known to happen both in and out of warranty. So far Panasonic when
contacted have also paid for repairs when out of warranty (2 years old)
(Anonymous)
Sony TV Model: KV27EXR25
Picture fades away few seconds after start-up till no picture. Sometimes no picture
at all. Sometimes picture OK for longer. Sound unaffected.
Faulty joints on CRT pcb. Cracked solder joints at tube socket connections on CRT circuit
board. Caused variable supply to CRT heaters. Resolder all socket pins to pcb.
(Col)
HOT is s/c, after replacement tv functions are erratic, snow on screen / goes into
standby / black screen
Change the VCU 2136 (It is possible to replace with a VCU 2133)
(Daniel)
Vestel TV (11AK19P3 Chassis)
Field reduced at the bottom of the screen with about one inch of undefined lines
instead of a picture
Oscilloscope checks at the rail supply U5 showed a high ripple content, replacement of the
smoothing capacitor CL52 (1000uF, 40V) cured the trouble
(Angovisao)
Various Video Model: Various
Severe NS bowing
Check for leakage of the small electrolytic capacitors on the vertical correction pcb at the
right of the main pcb, check C4014 in particular and if found to be faulty also check transistor
Q4009 (2SA950) which may also have been damaged
(Josh)
No Power
Check / Replace power switch, it read zero ohms at contacts - however carbon build-up stops
p.s.u. from starting
(B-1)
Hitachi TV Model: CPT1446R (NP84CQ Chassis)
H.T fluctuations, picture becomes half white and half black. H.T varies from about
80V to 110V
Replace ZD902. It's a 10V zener diode
(Sparky)
Philips TV Model: 25PT452A/11 (GR2.2 Chassis)
Set tries to start three times, HV comes up for a short moment. After this LED is
blinking first four times, then seven times
Change vertical chip TDA8177F and the four diodes in front of it
(Kalle - Sweden)
Dead
Check C822, Z801, Z802 (CPN10)
(Vlado - Macedonia)
Daewoo TV (CP785 Chassis)
No picture
Replace IC (TDA8385J)
(Vlado - Macedonia)
Sharp TV (5BSA Chassis)
Small picture
Replace D716 (27V) and D717 (75V)
(Vlado - Macedonia)
Thomson TV Model: 28WS23E (ICC17 Chassis)
Set trips off int. Set tries to come on then goes back to standby
Dry joints on line o/p transformer
(Ockbrook tv and video)
Saba TV (ICC8 Chassis)
No power
Replace Q805 (2SC3852A)
(Vlado - Macedonia)
Lg TV Model: CZ-20E60 (11.1 Chassis)
No power
Check +6v rail in PSU. If low replace capacitor CP19 (1000uF, 10v)
(Rich)
Philips Video Model: VR722 (VR722/02/05/08/13)
Dead
Check / replace R809 (0.47ohms). Could be the first indication of the chopper transforme
going faulty
(Anonymous)
Panasonic TV Model: TX25W1E
After about 30 minutes the set goes to standby, the LED flashes and TV starts
again. After 1 Minute the TV Displays : Antenna connection failed!
Change IC101 of IF on A-Board. Order Nr. 875946647
(Daniele Marseglia)
Matsui TV Model: 25M2 (Sanyo? Chassis)
Dry joints on regulator Q420, not too easy to find as it is not close to power supply or frame
stage, it is the supply to the frame generetor IC
(Shanks)
Samsung TV Model: CB5012Z (P58SC Chassis)
Standby LED blinks off when Standby pressed on remote control. Supplies do not
come up and set does not run.
Value of R256 (4K7 SMT) is marginal to turn Q504 on fast enough for micro to see supplies
come up. Replaced R256 with 1K (0805 SMT) problem solved
(Kevin - Plymouth)
Toshiba TV Model: CF2666R (TAC9102 Chassis)
At switch on the set pulsates 6 times before the H.T settles at 110V and the set
powers on
Replace R804 (0.56 ohms). It's located in the primary of the power supply and is used for
current sensing. Also note this is actually a Daewoo CP375S chassis
(Sparky)
Jvc TV Model: C14ET1EK (ONWA Chassis)
Intermittent dead with red standby light on, but won't switch back on, comes back
on it's own, won't respond to remote or local controls
Low 5v standby supply due to diode D869 faulty, check by replacement
Matsui TV Model: 14V1R
After presing play picture appears but looks like in pause mode
Clean and lubricate the capstan flywheel
(Santos Trejo)
Jvc TV Model: AV-S250EKT
No picture and no sound and when switching on, the high voltage transformer
makes a sound
The capacitor in pos. 2420 was bad (it produced smoke after some time)
(Kjell)
Mitsubishi TV Model: BD28WS (11AK19 Chassis)
At switch on front l.e.d turns green, blinks 3 times then set returns to standby. All
h.t voltages rise, then fall away as set goes into standby
Line transistor TL19 was short circuit. After replacement the transistor shorts again
Change capacitor CL21
(Anonymous)
Sharp TV Model: Unknown
Almost totally dead. No video or audio whatsoever. Only the clicking sound of two
power relays when the set is turned on, and conversely at power down. The
green/red lights on the front panel do appear. Repeated failure every 2-3 years.
Why ?
An insight into what TV engineers did, after speaking to Sony UK: (a) 0.47K resistor replaces
L656 in line to Q651 B. (b) 0.33 ohm resistor added between L650 and Q651 E. A resistor
also replaces L657. Still lasted only 2 years. Any better ideas ?
(George)
Vestel TV (11AK19 Chassis)
At switch on front l.e.d turns green, blinks 3 times then set returns to standby. All
h.t voltages rise, then fall away as set goes into standby
Dry joints IC807
(Lance)
This set had a bright picture, no off air video and no video via scart
The cure, thanks to Panasonic technical was to replace the memory chip I702 (X24C)
(Sparky)
Grundig TV (CUC6310 Chassis)
No east-west
Check R569, TDA8145, D566
(Louis)
Grundig TV Model: ST82-774 TOP/EURO
Standby led fault codes and meanings list / standby led flashes then pauses
Code meanings are as follows: 10 = child lock mode, 11 = timer mode, 14 = there is no
response from Iv01, 15 = there is no response from IS40, 20 = bus access prohibited by
software, 21 = bus data line held low, 23 = bus clock line held low, 25 = switched 5v supply
missing, 26 = crt is not warming in the allotted time, 27 = deflection failure more than three
times, 28 = IF01 guard voltage (pin 8) exceeded, 34 = no response from the nvm chip IR03,
36 = incorrect address passed to bus handler, 37 = unexpected level on NMI line (power fail),
41 = bus data line not recoverable
(Anonymous)
Sony TV Model: (FE-1 Chassis)
Dead set
I replaced the BU546 transistor in the power supply and resoldered some paths on the PCB.
An intermittent soldering path to the collector of the transistor was the reason for the
destroyed BU546
(Tom Bevers)
Samsung TV Model: TXG2547 (K51A Chassis)
After replacment of FBT, the set starts and reverts to standby mode immediately. If
the Crt heater is fed by an external transformer (i.e. 6 V. a/c), the screen will show a
very weak light, except in the corners
13V. was present on pin 11 of V. output IC TDA8350Q during the brief moment when the set
tried to start. The TDA8350Q was found to be defective and was replaced. Don't forget to
check +A voltage after replacing the FBT
(Jose Carlos Pinto - Oporto)
Hitachi TV Model: C1709T
Dead
Check C1003 (1uF, 100v) then the STRD1806 and D1004 for s/c
(Anonymous)
Philips TV Model: 28ML8805-16B (FL1.6AA Chassis)
No start up, l.e.d flashes orange 7 times then stops. All rails on secondary of
chopper seem ok
You will probably find the line o/p transformer is at fault
(Sparky)
Sony TV Model: KVS3432U (AE2 Chassis)
Front led flashing 13 times, HT at first came on at 139V then went to 75V going off
etc (shuting back down in protection mode)
Found R854 open circuit on -15 volt line (off line output transformer)
(Errol Rankin)
Finlux TV Model: 71G2 ID:54361330 (Stereo Plus Chassis)
Bottom half of the screen is black. Very distorted picture in top half. Volume weak.
The programming menu, and the "Extra" menu, has disappeared. In "Service mode"
(Mute, M and TV buttons in sequence), all settings are set to the max. value (63)
The existing IC "SPL 40R01" in location NF10, and the connected EEPROM in location
NF80, was replaced with replacement IC "SPL 51R02" and an empty EEPROM. It comes in a
kit, which also includes installation instructions and a user manual
(H. Rosenberg)
Jvc Video Model: HRD560
3/4 of the playback picture is snow may look like duff heads!
Check 3.3uF,50v capacitor on lower drum motor pcb, this is an smd type but can be replaced
with standard cap mounted on its side and tilted downwards slightly to clear mech chassis
(K Ferrier)
Noisy capstan
C22 in Power supply fixed it for me
(Anonymous)
Various Remote Controls
Handheld remote problems, quick check which everybody might not know
Switch broadcast radio to medium waveband, around mid-band. From about two feet away
point remote at radio and press any button. All buttons should cause radio to bleep. Not clever
but useful. Any other ideas ?
(David Kilmarnock)
Saba TV Model: M3715 (TX805 Chassis)
Volume up full, red bargraph but no sound, Picture bargraphs also at full and will
not adjust
Disconnect pin 1 of MN1220, press vol down then store then resolder pin 1 - only seems to
correct problem if resoldered while unit is powered.
(Bku)
Mark TV Model: TVD1420TX
Poor starting, some times comes on then cuts out with LED going out
Dry joints along centre heatsink where the three ICs are mounted, reflow solder on ICs and
then check HT (160 Volts)
(Anonymous)
Sony TV Model: KV-25M80 (BG-2 Chassis)
Dead
5V Supply Transformer Short
(Subhash)
Goldstar TV Model: CF28A54L (PC58A Chassis)
No sound, speakers pop out if volume is raised from zero. Audio output from
Dolby (A1) board at +5v dc.
Lightning damage to this set and connected VCR. Centre/surround amplifier IC shorted
blowing IC protector to its negative rail. Both amplifier ICs replaced as a precaution. No
damage to Dolby (A1) board
(Simon)
Philips TV (L6.2 Chassis)
AV1, AV2 are fine but AV3 do not work. Picture may be ok but no sound
Replace BA7604N, and check CX64 (47pF)
(Daniel Simes - Portugal)
Daewoo TV (CP775 Chassis)
No tuning
R124 (15K) o/c, (33 Volt tuning supply)
(Apollo service centre)
Loewe Opta TV Model: Contur T70 (C9000 Chassis)
Dead
One of the three series connected 68Kohms resistors was open-circuit. RP44 is rated at only
0.25w. It hides beneath two large green power resistors. The other two 68Kohm resistors are
rated at 0.5W. We replaced them all with 1W resistors. Soak tested ok
(Ann Reid)
Orion TV (5130-2RC Chassis)
Picture was black and white, twisted, sound came and went
If switched on for a long time the picture improved but was still not OK. Capacitor C210 in
the IF section had failed. Replaced and all OK!
(Pavel)
Hitachi TV Model: C2864TN
Display shows dew sensor at irregular intervals and different circumstances causing
the video to go in standby mode
Bouncing effect of power switch on timer board. Only one section of this double pole switch
is used. Add a 1nF capacitor in parallel to this switch and use the second section as well
(Robert)
Sony TV Model: KVM1400
Replace ICP fuse in HT line PS801 (N15, 600mA) mounted adjacent to pin 7 of LOPT
(Dave)
Panasonic TV Model: 21LIT
PLL will not lock for all frequencies (keeps running during program search), on
screen display moving / unstable
Changed the tuner and the STV8224 also check transistor at location TV02 is ok
(Anonymous)
Hitachi TV Model: C2546TN
Excessive width
This was due to Q532 (2SK2251-01) being s/c, it is advisable to also check other EW circuit
components as a precaution
(Josh)
Sharp TV Model: 54DT25S
Frame foldover
Check C713, Q510 and Q505
(A. McGovern)
Samsung TV Model: CB7230WT
NO D VIDEO
QUERO O PROGRAMAO DO INTEGRADO DE MEMORIA DO 24CO8
(Anonymous)
Toshiba Video Model: V730UK
Dead
PR512 in the PSU was o/c
(Paul)
Sony TV Model: KV2020
No Sound
Replace sound i.c (TBA120U)
(Anonymous)
Toshiba TV Model: AVM 2505 (G3V25050 Chassis)
Intermittent dead
When pin 11 of IP001 (U4614) jumps between 8v and 10v suspect shorted 2SA1020, as the
secondary is shorted, leaving the chopper switching between on/off states
(Liran Daniel)
Panasonic TV Model: CT-T14R
El diodo en paralelo con condensador electrolitico C810 vuela porque este voltaje
esta bien alto cerca a 200 voltios debe ser 138v
Cambiar la R610 de 110k (estaba alterada)
(Juan)
Vestel TV (11AK19 Chassis)
Screen blanked out with 4 coloured lines two thirds of the way down from the top
of pic. Sound OK
100 ohm resistor connected to pin 6 of the frame output chip was o/c. The IC is TDA8356.
The resistor is R704 and is on top of a small hole in the chassis
(Raul Almeida)
Grundig Video Model: VS500VPS
Loss of colour
Filter BP301 may have poor internal contacts
(Anonymous)
Bush TV Model: 2059NTX
Dead
Fit a power supply kit from SEME RK215 for a safer and reliable repair
(Anonymous)
Philips TV Model: 14PT1352/58 (L6.1AA Chassis)
The fault with this tv was a snowy picture (no channels tuned in) also the
permanent 33V supply on pin 9 of the tuner was low at only 1.6V
The first thing i tried was a resistance check between pin 9 and ground. The reading was only
120 Ohms. There's a surface mounted cap right next to pin 9 of the tuner. This was found to
be leaky, It's value is 47nF. Also resistor 3442 (3.9K) was o/c
(Sparky)
Lg TV Model: CI29H40 (PC8KA Chassis)
There was a bright white screen with flyback lines on this set. The A1 adjustment
had very little effect
I found that IC901 (TDA6108JF) on the tube base was faulty, pin 7 (blue o/p) and pin 8
(green o/p) both read s/c to ground. Note: this chip was probably taken out due to the tube
flashing over as in my case
(Sparky)
Philips TV (ANUBIS A Chassis)
Low Contrast
C2448 (47uF, 200v) open circuit
(Paul Willis)
Bush TV Model: 1473T
Dead
This was due to C14 (1uF, 63v) in p.s.u being faulty, replaced with a 2.2uF, 63V
(Markus)
Seleco TV Model: 26SA37NL
Salora TV (L Chassis)
Dead
DN15 s/c (8v line)
(Anonymous)
Mitsubishi TV Model: CT29B2STX
Field collapse
Check R410 (1ohm) in feed to D403 for o/c
(Anonymous)
Toshiba Video Model(s) V632UK, V642UK, V752UK, V852UK
No or very dull picture with osd and text just visible, A1 control makes little
difference, looks like poor crt
18v zener diode Z703 s/c located near lopt, it is part of the acl beam current limiter
(Simon Edwards)
Sharp TV Model: 66FW53H (DA100 Chassis)
No Power - dead T700 and T701 (BUW41B) and R713 (22ohms, 5W). New parts
work short time and dead again
Dry capacitors C712 and C726 (4.7uF, 35V)
(Raymundo)
Hypson TV Model: HY1493 (3915 TH Chassis)
no. 260P255040) and for dry joints around R954, R974 and R985
(Anonymous)
Philips TV Model: (GR2 Chassis)
Image appeared after a 5-20 minutes, sound was choppy when changed by the
remote
Replaced C2690 (100F, 50V) with a 100F, 63V type, this is located on the small overvolt
board in the power supply area
(Jy)
Philips TV (CP110 Chassis)
No e/w correction
This was due to T504
(Anonymous)
Finlux TV Model: SN87A2
No sound or picture
Check R44 for o/c and D20 for s/c
(Anonymous)
Sinudyne TV Model: 34B0A
No image from tuner. Image from AV input (rgb) is rolling over the screen (no
synchronisation)
Check if teletext is present at the top of the screen. If this is ok replace the TDA5931
(normally the sound will also be missing)
(Trancy boy 1)
Grundig TV (CUC4400 Chassis)
No vertical
R822 (15K) open
(Joao Soares)
Panasonic Video Model: NVHD100
Narrow sync pulse output in E-E but ok when pre-recorded tape is played
Replace 3.3uF, 50v SM capacitor on hybrid IC301, If fault persists replace IC301 on the Y/C
sub board
(J. Herbert / Anonymous)
Sony TV Model: (BE1 Chassis)
Loss of sound when set was cold / extremely distorted sound when cold (after set
was turned on)
Sound recovered within a few minutes of turn-on and was then normal. Check the electrolytic
capacitors and diode near to the audio output IC heatsink. 100% rectification was achieved by
replacing the diode and small value electrolytics in the immediate area of this IC's heatsink
(Steve Larkins)
Sharp TV Model: 51DT25H (U Chassis)
Picture too big, maybe strange colors, shuts down after a few seconds
Check for shorts in IC606 (9V voltage reg)
(Kalle Birgersson, Uddevalla Sweden)
Philips TV Model: 28PW6005 (A10 Chassis)
No line drive
This one had me puzzled for a while until I found that diode D861 was open-circuit
(intermittently!)
(Graham, Falsgrave Electrical)
Matsui TV-Vid Combi Model: TVR185
No picture No sound
Faulty IC TDA6107q on crt board
(Imran)
Seg TV Model: CTV7951GB
Dead set
Check the following caps, C828 (1000uF, 16v), C817 (1000uF, 16v) and C848 (100uF, 25v).
The caps take out the following components in the power section. Chopper FET Q802
(2SK2545) equivalent BUZ901A (need to isolate BUZ901A from heatsink), R817
(2.2ohm/5W), D805 (BA159), D802 (IN4007) and D801 (IN4007)
(Ian Paterson)
Jvc TV Model: AV25SD4EK
Standby LED changes from Red to Green as normal, but no picture or sound. Set
appears not to come out of standby
Check for dry joints on the line output transformer tags. Resolder all as a precaution anyway
(John)
Sharp TV Model: 66FW53H
Sometimes does not start up from cold, but starts well from power off or standby
after a few minutes
After checking all PSU components and consulting many colleagues, casually the tip of my
iron touched the body of T2628 (BF423) and the set started. After more then 20 attempts, I
realised that this transistor became intermittent when cold
(Jose Carlos Pinto - Oporto)
Samsung TV Model: CX5012
Dead, no line oscilation, power supply and line output stage are OK
Check / replace C2549 (390 or 470nF / 400V) and C2545 (1n5 or 1n2, 2000v)
(Anonymous)
Philips TV Model: 14GR1221 (GR1AX Chassis)
This set would not switch automatically into A/V mode when a video or any other
equipment was connected via the scart
The set could manually be placed into A/V from the tv's front end controls. The cure was to
replace ZD301 (ZTE251). I assumed it was a 2V but as i had none in stock i tried a 2.7V
zener which worked perfectly. It's located near the scart socket
(Sparky)
Panasonic Video Model: NV-G40
The H.T wouldn't vary at all, even though it was actually at the correct level (157V)
ZD941 (BZV10) was found to be o/c. It's a 6.5V zener diode and not as i had assumed by the
numbering on it a 10V. ZD941 and the H.T pot VR941 are located next to the optocoupler
(Sparky)
Nokia TV Model: SP71D1 and others (Stereo Plus Chassis)
Appears to be no line drive but if scoped the drive is at very high frequency
Suspect C308 (3.3nF) high stability type
(Jamal)
Panasonic TV Model: TC1400T
Set shuts down shortly after start up with standby led flashing 2, 4 or 5 times
Check / replace chip resistors R543 (47Kohms) and R541, R573 and R575 (all 100Kohms)
(Josh)
Grundig TV Model: 8214
Audio, no video
Change Capacitors C4501 and C4502, in the vertical section
(Anonymous)
Ferguson TV (ICC9 Chassis)
Ew distortion
Check / replace CL42 (4.7uF, 160v), don`t forget to use 105 Celsius type replacement
(Anonymous)
Sharp TV Model: DV3760H
No remote control op
Microprocessor MN15151
(Anonymous)
Ferguson TV (TX92 Chassis)
Dead, No LED, 2.5Amp fuse O.K. Some voltages present at BP02 ON/OFF switch
connection. 160v at terminal D of TP16. 26v, 200v, 13v lines all zero
Replace TP16 (P6NA60FI) and diode DP17 (BZX55C15)
(Col)
Sony TV Model: KVA2542
Fault not limited to this model. Turning itself to standby, mostly when warm.
Flashing error code on LED's.
Dry joint on IC TDA8179 (under metal shield). May need replacing with STV9379. May also
need to alter picture geometry settings (HSIZE, HPOS, VSIZE, VPOS) in service menu
(Garth)
The word "factory" in a red box is permanently displayed on screen and sound
volume goes from 0% to 50% to 100%
Enter service mode, go down to nvm and press volume plus on remote
(Anonymous)
Toshiba TV-Video Combi Model: VTV1402S
E/W fault
Coil L603 (part num RCILP0286BMZZ) had severely burnt up and Q506 E/W driver
2SD2391 (Part num RH-TX0151BMZZ) was short circuit. If you have this fault check L604
for invisible dry joints, if you don't you may find you still have an E/W fault when you have
replaced the faulty parts
(Regards - LB)
Goldstar TV Model: CIT-9322
Reddish picture
Replaced Transistor Q2005 Type 2N3906 (shorted)
(Anonymous)
Mitsubishi TV Model: CT29B2STX
After replacing the line output TX the set still appears to be tripping
Try switching the set on with the remote control. The micro seems to remember the tripping
state, the remote control re-setting it
(Anonymous)
Toshiba Video Model: V709B (Samsung Chassis)
Does not start when cold, simply produces a very fast trrrr noise...
Increased value of C711 (10uF, 63V) by adding a 4.7 uF in parallel on the bottom side of the
printed circuit board
(Vusu)
Daewoo TV-Video Combi Model: GB14F7T1
At switch on the Led Blinks 3 times, supply tries to come up with a Tick-Tick
sound. After trying 4 times to come up it goes to error standby with Led blinking
very fast. Error code 3
Make sure primary side of power supply is ok by desoldering jumper JL26, connect Pin 3 of
IL01 (protection) to pin 4 ground. Bypass DP127. Put 100W/230V lamp on usys. Turn on the
set the lamp should glow and pot PP120 should regulate it. I found CL007, CL015 and TL003
shorted
(Navneet)
Grundig Video Model: GV400 / GV440
Blue screen, no sound (ok on scart) or snow on screen, no sound, no service mode
and menu text fluctuates, channels can not be tuned
The tuner was faulty
(Anonymous)
Philips TV (L6 Series Chassis)
Vertical lines are not straight when picture is very bright or has white text content
Replace resistor 3420 in the beam current circuit (12k or 15k) replaced with an 18k
(Etienne)
Severe field cramp at bottom of the picture, but very stretched picture at the top
C608 (4.7uF, 63v.) in field stage o/c
(I.g.d.)
Sony TV Model: KVM2511 (AE1 Chassis)
Crackling audio
Check for failure of IC101 (KA2914A) (TA7680AP equiv)
(Anonymous)
Itt TV Model: ITT 3362 (Pico 2/ST3 Chassis)