You are on page 1of 230

Solenoid Valves Catalogue 2009

Main Contents

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Coil
General Description
The GEM-SOL coil is designed to be
mounted on the "operator" to set up a
solenoid valve.
The coil, including its magnetic circuit, is
encapsulated in high temperature resistant
nylon to withstand humidity and heavy
duty requirements.

Notes
The coil should not be energized without
being assembled on operator.
All GEM-SOL coils are designed to operate
at 10% of nominal voltage.
Our engineering department is able to design
coils to any special requirement, they can then
be produced in any quantity specified.
GEM-SOL coils are suitable to work at
100% ED, however when energizing AC8W or
DC10W coils for a long time, the temperature
developed may affect solenoid seals. Please
consult our technical sales department to get
further information on the use of lower power
coils or Viton seals.
For outdoor applications or when the coil is
exposed to high humidity, we recommend the use
of impregnated coils. Please contact our technical
sales department for specific requirements.

How to Order
Example : GEM-B-341

GEM-B

Is a GEM-SOL Coil 24V AC 5.5W 50 Hz with connector.


Available variations coils table

AC
50 Hz

60 Hz

DC
(W)

V
8 5.5 2.5 8 5.5 2.5 10 5.5 3.5
6
12
24
48
110
120
230
240
other : Please contact our technical sales
department for specific requirements.

1.1

Voltage
6
12
24
48
110
120
230
240
other

Connector

Power
1
2
3
4
5
6
7
8
9

AC8W 50Hz
AC8W 60Hz
DC10W
AC5.5W 50Hz
AC5.5W 60Hz
AC2.5W
DC5.5W
DC3.5W

1
2
3
4
5
6
7
8

without
with
with LED
with bi
color LED
flying leads coil
with 1/2" Hub
other

0
1
2
3
4
5
9

GEM-SOL Index
Technical Specifications
Power Consumption Table (AC)

Coil winding insulation:

H 180

Temp Range:

-20 C to 150 C

Duty cycle:

100% ED (Ambient temp -20 C to 70 C)

Protection:

IP65 with connector

Voltage range:

Standard industrial voltage 6 to 415VAC or DC

Voltage variation:

Nominal 10%, over voltage category II

Power consumption:

AC - see table

Type

Inrush

Holding

8W

26VA-13W

16VA-8W

5.5W

16VA-8W

12VA

2.5

2.5W

2.5W

DC 10W, 5.5W, 3.5W


Electric connection:

AMP pins, DIN 46242, 2 poles + 1 earth


2 flying leads, AWG18 300mm length

Junction box:

DIN 43650

Cable exit::

PG9 or 1/2" NPT

Assembly:

In any position

Fixing:

One nut G1/4" hexagonal 19mm

Weight:

100gr.

Dimensions

GEM-SOL with
Flying Leads

GEM-B-31
24V 50Hz 8W

1.2

SV-04-09

GEM-SOL Index

Technical Info

GEM-SOL Index

GEM-SOL Index
BACCARA

GEM-SOL Ex Coil
according to ATEX 94/9/EC (ATEX 100a)

II 2 G Ex mb II T6 IP65
General Description
The GEM-SOL Ex coil is designed to
be mounted on a GEM- SOL valve.
The coil meets the guidelines of ATEX
97/9/EC, EN 60079-0 and EN60079-18.
The coil uses a pulse wide modulation system
to reduce the power rating of the coil to about
1 (w) at holding.

Notes
This coil must be mounted on a GEM-SOL solenoid valve.
It can only be used with the media specified for
GEM-SOL valves. It is for use in:
Explosion Group II, Category 2G, and Temperature
Class T6.
This coil must be protected against direct and other
U.V. light.
The type of protection used is Encapsulation Ex mb,
by potting Epoxy.
Certification: DEMKO 08 ATEX 143928X
Use with DC GEM-SOL valves.
To order valves manufactured to your specific
requirements, please contact our technical sales
department.

How to Order
Example : GEM-BE-1-31
Is an Ex GEM-SOL coil 24V both AC and DC current.

GEM-BE

Type
1

Power (1)

Voltage
12
24
48
110
230

2
3
4
5
7

1W

(1) The power rating is an average value at holding.

1.5

Technical Info

GEM-SOL Index
Technical Specifications
Coil winding insulation:

Class H (180C)

Ambient temperature:

-20C to 50C

Explosion proof environment:

Per. ATEX 94/9/EC

Protection method:

Ex mb IIC T6 IP65

Coil duty cycle:

100%

Ingress protection level:

.. -21 .. -31 .. -41 .. -51 .. -61


Voltage [V]

12

24

48

110

230

Inrush current [mA]

720

400

200

88

40

Power inrush [W]

8.6

9.6

9.6

9.7

9.2

IP65

Holding current [mA] 66

36

20

Electrical connection:

2[m] PVC cable with


0.75 [mm2] conductors

Power hold [W]

0.9

0.9

0.9

0.9

Assembly:

In any position, fixing

II 2 G

0.8

with G1/4 hexagonal nut


300 [grf]

Weight:

Electrical specifications:
Voltage variation:

10% of nominal voltage

Voltage:

Both AC and DC

Inrush time:

50 [msec]

Holding power:

1[W] - average value

Dimensions

45

80.5
17

13.2

33

12

1.6

SV-04-09

GEM-SOL Index
BACCARA

GEM-SOL IP 68 COIL
General Description
The GEM-SOL IP 68 coil is designed to be
mounted on the "operator" to set up a
solenoid valve.
The coil meets the requirement of the
European Standards IEC 529 code IP68.

Notes
The coil should not be energized without
being assembled on operator.
Voltage rating is 10%.
For best results, the coil should be mounted
on sealed operators. Please consult with our
technical sales department.
Use with GEM-SOL valves suitable for the
coils power.
Suitable for infinite immersion up to 2m depth.
Please contact our technical sales department for
specific requirements.

How to Order
Example : GEM - BP - 31
Is an IP68 GEM-SOL coil 24V AC 8W 50Hz.

GEM-BP

Voltage
12
24

Power
2
3

AC8W 50Hz
AC8W 60Hz
DC10W
AC5.5W 50Hz
AC5.5W 60Hz
AC2.5W
DC5.5W
DC3.5W

1
2
3
4
5
6
7
8

1.7

Technical Info

GEM-SOL Index
Technical Specifications
Construction:

Housing encapsulated Polyurethane

Coil winding insulation:

H 180C

Ambient Temp Range:

-5C to 50C (no icing)

Duty cycle:

100% ED.

Protection:

IP-68 Infinite immersion up to 2m depth

Voltage range:

12, 24 AC and DC

Voltage variation:

10%, over voltage category II

Electric connection:

3x0.75 200cm, hook up wire

Assembly:

In any position

Fixing:

One nut G1/4" hexagonal 19mm

Power Consumption Table (AC)


Type

Inrush

Holding

8W

26VA-13W

16VA-8W

5.5W

16VA-8W

12VA

2.5W

2.5W

2.5W

Dimensions

1.8

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Operator 2/2, 3/2 Way


General Description
The operator is designed to be assembled on a valve
or a counterpart, to set up a solenoid valve.
According to the operator and valve construction, all
functional versions are possible: 2/2-3/2 way
normally closed or open.
The operator is mounted on all our solenoid valves.
It may be used with alternating or direct current.

Notes
Operator seat should be designed according
to our specifications.
Operator for DC is without shading ring and may
not be used for AC.
ADC operators and valves are suitable for use
with AC 8W or DC 10W. When an order of an
operator or a valve is without a coil, ADC
operators will be supplied.
When assembling coil, take care not to tighten
nut excessively.
Valves are inspected at general pressure of
12 bar. Higher pressures are available.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

2W NC

How to Order

2W NOa through base

3W NOa through base

3W

Example : GEM-O-2W1-N-341

Is a GEM-SOL Operator, 2W NC, NBR, 24V AC 5.5W 50 Hz with connector.

Example : GEM-O-1034-V-341
Is a GEM-SOL Operator, 1/8BSP, 3W NC,Orifice 2.0, Viton, 24V AC 5.5W 50 Hz with connector.

2W
GEM-O

2W

2W NC
2W NO(1)

3W
GEM-O

1/8"BSP
1/8"NPT

10
11

2W NO
3W NC
3W NO
3W NO(1)

NBR
Viton
EPDM
PTFE(3)
Kalrez(2)

1
2a

Function

Port

Voltage

Seals

Function

Orifice
2
3
4
4a

0.8
1.2
1.6
2.0
2.4
3.0

1
2
3
4
5
6

N
V
E
T
K

W/out coil
6
12
24
48
110
120
230
240
other

0
1
2
3
4
5
6
7
8
9

No coil
AC8W 50Hz
AC8W 60Hz
DC10W
AC5.5W 50Hz
AC5.5W 60Hz
AC2.5W
DC5.5W
DC3.5W

(1) Supply pressure through base.


(2) Kalrez O-ring is available only upon request.
When ordering Kalrez seals, please consult
with our technical sales department about
O-ring compound.
(3) For PTFE seals, the O-ring is Viton seal
as default.Please contact us if you require
a different O-ring.

1.9

Connector

Power
0
1
2
3
4
5
6
7
8

without
with
with LED
with bi
color LED
flying leads coil
with 1/2" Hub
surge protection
with LED
other

0
1
2
3
4
5
6
9

GEM-SOL Index
Technical Specifications
Function:

2/2-3/2 way NC or NO

Operator assembly:

Orifice size:

0.8 up to 3mm

hexagonal 22 to the

Pressure range(bars):

See solenoid valve performances

valve body and fixing coil

Flow factor Kv(l/min):

See solenoid valve performances

by one nut G1/4" hexagonal

Temperature range:

Fluid: According to seals.

19mm, of metal or plastic.

Ambient: -10 C to +50 C


Response Time:

16 to 36 ms complete cycle

Cycling rate:

1600c/min

Coil position:

By screwing M20X1

Any position, may be turned


360 on the operator

Coil data:

See technical coil data

Materials in contact
with fluid:

Operator:
Stainless steel
series AISI 300 & 400
Shading ring:
standard - copper
upon request - silver and aluminium
Orifice:
Stainless steel

Weight:

180g

Media:

Air, gas, water, fuel, oil etc

Threads on operator tube: G1/4" male - G1/8" or 1/8" NPT female


to connect exhaust, muffler, etc.

Dimensions

GEM-B-31
24V 50Hz 8W

63.5

5.70.1

2W/3W NC, NO

GEM-B-31
24V 50Hz 8W

Operator seating

2W/3W NO through base

1.10

SV-05-10

GEM-SOL Index

Technical Info

GEM-SOL Index

GEM-SOL Index

Technical Info

GEM-SOL Index

Technical Info

GEM-SOL Index

BACCARA

GEM-SOL Large Orifice Direct Operated


1/4" 2/2 Way NC, NO (Pressure & Vacuum)
General Description
These GEM-SOL 2/2 Way NC, NO solenoid valves are
recommended for heavy duty applications where
high performance is required.
These valves are recommended for vacuum
application, but can be used for air, water and
oil; please consult with us if you need the valves
to work with other fluids.

Notes
ADC valves are suitable to work
only with AC 8W or DC 10W coils.
Latch valves are available upon request.
Valves are without manual
override. (2/2 way NC valves).
When ordering PTFE seal, Viton
O-ring will be used.
To order valves manufactured to your
specific requirements, please contact
our technical sales department.

IN
P
(2)

OUT
A
(1)

How to Order
Example : GEM-A-2201aV-311
Is a GEM-SOL direct operated Brass, 1/4"BSP,
2W NC, 8.0 orifice, Viton, 24V AC 8W 50 Hz with connector.
Note: When ordering without coil, please define what current and pressure rating is needed (DC, AC or ADC).
When this information is not defined, an ADC valve will be supplied.

GEM-A

Body
Brass
St.st

2
3

Port
1/4" BSP
1/4" NPT

Function
20
21

2W NC
2W NO

1
2

Orifice
6.0
4.5
8.0(2)

8
9
a

(1) Kalrez O-ring is available only upon request.


When ordering Kalrez seals, please consult
with our technical sales department about
O-ring compound.

(2) Not available in NO valve.

1.15

Voltage

Seals
Viton
EPDM
Kalrez(1)
PTFE

V
E
K
T

W/out coil
6
12
24
48
110
120
230
240
other

Connector

Power
0
1
2
3
4
5
6
7
8
9

No coil
AC8W 50Hz
AC8W 60Hz
DC10W
AC5.5W 50Hz
AC5.5W 60Hz
DC 5.5W

0
1
2
3
4
5
7

without
with
with LED
with bi
color LED
flying leads coil
with 1/2" Hub
surge protection
with LED
other

0
1
2
3
4
5
6
9

GEM-SOL Index

Technical Specifications
Function:

2/2 Way NC, NO

Ports size:

1/4" BSP & NPT

Orifice:

4.5, 6.0, 8.0

Kv:

See table

AC/8W

4.5

Pressure range:

From -1 to.... see table

AC/5.5W

3.8

Temperature range:

Fluid: max 80 C

DC/10W

4.5

3.8

1.5

DC/5.5W

3.2

10

Max.Pressure (bar) 2W NC Table


Coil
Current/Power

Ambient: -10 C to 50 C
Manual Override:

None

Materials :

Main valve:

Flow factor Kv(L/min)

Orifice

4.5

Orifice

Orifice

3.8

2.5

6.0

8.0

Brass or Stainless steel 316


Solenoid Operator:
Stainless steel 300 & 400

series

Max.Pressure (bar) 2W NO Table

Seals:

Coil
Current/Power

Viton, EPDM, Kalrez or PTFE


Weight (with coil):

366 gr

Media:

Air, water, oil

Coil voltage:

All Baccara coils voltages 10%


AC 8W, 5.5W

Orifice

Orifice

4.5

6.0

ADC

AC/8W DC/10W

Flow factor Kv(L/min)

DC 10W, 5.5W
Protection class IP65 with connector

Dimensions
22

Mounting Bracket

30

40
61.2

1.16

SV-04-09

Technical Info

GEM-SOL Index

GEM-SOL Large Orifice Direct Operated


1/4 3/2 Way NC, NO (Pressure & Vacuum)

When ordering valves, please refer


to the Orifice table below.
Ex
NC
Ex

NO
In

DC

To order valves manufactured to your


specific requirements, please contact
our technical sales department.

In NC

Vacuum
Pump

Ex NO
P
(1)

Example : GEM-A22028V-331

Pressure Application

(1)

Pressure
3
4

Tank

Out
NC/NO

Pressure 1
Vacuum 2
(2)

A
(2)

Vacuum Application

(3)

No coil
AC8W 50Hz
AC8W 60Hz
DC10W

0
1
2
3

other

(1) See Notes : Orifice table


(2) Not available in NO
(3) Please refer to Notes : Orifice table
for current availability

1.17

GEM-SOL Index
Technical Specifications
Vacuum Application

Function:

3/2 Way NC, NO

Ports size:

1/4" BSP & NPT

Orifice:

Bottom orifice: 8.0mm, 6.0mm, 4.5mm

Function

Top orifice: 3mm, 4.5mm, 5mm (see Notes)

4.5

3W NC

-1

Kv(L/min):

See pressure range table

3W NO

Temperature range:

Fluid: max. 80 C

Flow factor Kv(L/min)

Orifice
6.0
-1

-1 to 1 -1 to 0.5
5

8.0
-1
NA
10

Ambient: -10 C to 50 C
Manual Override: None
Materials :

Main valve :

Pressure Application

Brass or Stainless steel 316

Function

Solenoid Operator:

3W NC

4.5

Orifice
6.0

8.0

2.8

1.6

0.5

Seals:

(for 3mm
3W NO top orifice)

1.5

NA

Viton or EPDM

Flow factor Kv(L/min)

10

Stainless steel 300 & 400 series

Weight (with coil):

366 gr

Media:

Air, water

Coil voltage:

All Baccara coils voltages 10%


AC 8W

DC 10W

Protection class IP65 with connector

Dimensions
Mounting Bracket

1/8 BSP/NPT

GEM-B-31
24V 50Hz 8W

30

9.5 TYPx2
61.2

40

1.18

SV-03-10

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Direct Operated TYPE HF (CNOMO)


3/2 Way NC, NO
General Description
GEM-SOL (CNOMO) solenoid valves are designed
to be mounted on a sub-base or on an appropriate
counterpart adapted to this valve type.
This version is suitable for mounting any number
of valves on the same sub-base plate. Any combination
of 3/2 way normally closed or normally open may be
grouped together.

Notes
Valves are inspected at general pressures
of 12 bar or less (see table).
Valves for higher pressures are available.
ADC valves are suitable to work only with
AC 8W or DC 10W coils.

GEM-H

Body
Mazak

Function
1

3W NC
3W NO

3
4

Orifice
0.8
1.2
1.6
2.0
2.4
3.0

Manual
Override

Seals
1
2
3
4
5
6

NBR
Viton
EPDM

N
V
E

None
90 turn
Push in

1.19

0
1
2

Voltage
W/out coil
6
12
24
48
110
120
230
240
other

Connector

Power
0
1
2
3
4
5
6
7
8
9

No coil
AC8W 50Hz
AC8W 60Hz
DC10W
AC5.5W 50Hz
AC5.5W 60Hz
AC2.5W
DC5.5W
DC3.5W

0
1
2
3
4
5
6
7
8

without
with
with LED
with bi
color LED
flying leads coil
with 1/2" Hub
surge protection
with LED
other

0
1
2
3
4
5
6
9

GEM-SOL Index
Technical Specifications
Functions:

3/2 Way NC & NO

Orifice:

See table

Kv:

See table

Pressure range:

See table

Temperature range:
Manual Override:
Materials :

Max.Pressure (bar) 3W NC Table


Coil
Current/Power

Orifice

0.8

1.2

1.6

2.0

2.4

3.0

ADC

23

20

15

10

5.5

Fluid: max 80 C

AC/8W DC/10W

35

30

17

14

10

Ambient: -10 C to 50 C

AC/5.5W

23

20

15

10

5.5

Brass 90 turn or

AC/2.5W DC/5.5W DC/3.5W

20

16

10

brass push-in

Flow factor Kv(L/min)

0.6

1.1

1.7

2.5

3.5

4.5

Main valve :

Max.Pressure (bar) 3W NO Table

Mazak
Solenoid Operator:

Coil
Current/Power

Orifice

0.8

1.2

1.6

2.0

2.4

3.0

ADC

25

20

15

11

NBR, Viton or EPDM

AC/8W DC/10W

30

22

17

12

10

Weight (with coil):

250 gr.

AC/5.5W DC/5.5W

25

20

15

11

Media:

Air

AC/2.5W DC/3.5W

20

18

12

Coil voltage:

All Baccara coils voltages 10%

1.4

2.2

3.0

3.5

Stainless steel 300 & 400 series


Seals:

Flow factor Kv(L/min) 0.6

AC 8W, 5.5 and 2.5 W &


DC 10W, 5.5 and 3.5W
Protection class IP65 with connector

Dimensions

port (2)

port (1)

1.20

SV-04-09

GEM-SOL Index
BACCARA

GEM-SOL Direct Operated TYPE V & VL


2/2 Way, 3/2 Way NC, NO
General Description
GEM-SOL solenoid valves are designed to be
mounted on a sub-base or on an appropriate
counterpart adapted to this valve type.
This version is suitable for mounting any number
of valves on the same sub-base plate. Any
combination of 2/2 or 3/2 way normally closed
or open may be grouped together.
The modular manifold design enables to achieve
any manifold length.

Notes
Valves are inspected at general pressures of 12 bar or
less (see tables).
Valves for higher pressures are available upon request.
Valves for pressure higher than 25 bar are less manual
override. (For valves with pressure higher than 12 bar,
please refer to section 5 on page 7.5).
Baccara manufactures two types of NO valves:
Supply pressure is through the base as in NC valves.
These valves can be combined in a standard manifold.
They are without manual override.
Supply pressure is through the tube. These valves
cannot be combined in a standard manifold. They are
with manual override.
When using a manifold with more than 8 stations it is
advisable to use two air supplies, one at each end.
ADC valves are suitable to work only with AC 8W
or DC 10W coils.
LATCH valves are available upon request.
When ordering pressure separation plug, please add
Part No.125110000 to your order.
To order valves manufactured to your specific requirements,
please contact our technical sales department.
Size:
Assembly:
Port size:
Material:

Any number of stations, built from three basic components:


Left End Section, Right End Section and Middle Section.
Push in and turn 90 clockwise
1/8" BSP or NPT
Mazak

How to Order Manifold Components: Example : GEM-V-102


Is a GEM-SOL 'V' type manifold 1/8" BSP right component.

GEM-V

Port
BSP
NPT

Component
10
11

Left
Right
Middle

1
2
3

1.21

Technical Info

GEM-SOL Index
Technical Specifications
Function:
Mounting:
Orifice:
Kv:
Pressure range:
Temperature
range:
Manual Override:

Materials :

Weight (with coil):


Media:
Coil voltage:

Max.Pressure (bar) 2W, 3W NC Table

2/2, 3/2 Way NC & NO


Vertical, on sub-base 2 screws M4
See table
See table
See table

Orifice

Coil
Current/Power

Fluid: max 80 C
Ambient: -10 C to 50 C
Plastic, brass screw or
brass finger knob. NOa are without
manual override
Main valve :
Mazak, Brass
Solenoid Operator:
Stainless steel 300 & 400 series
Seals:
NBR, Viton or EPDM
220 gr for Mazak valve
Air, water, oil
All Baccara coils voltages 10%
AC 8W, 5.5W and 2.5W &
DC 10W, 5.5 and 3.5W

0.8 1.2 1.6 2.0 2.4 3.0

ADC

23 20

15

10

AC/8W DC/10W

35 30

17

14 10

AC/5.5W

23 20

15

10

8 5.5

AC/2.5WDC/5.5WDC/3.5W

20 16

10

Flow factor Kv(L/min)

0.6 1.1 1.7 2.5 3.5 4.5

8 5.5
6

Max.Pressure (bar) 2W, 3W NO Table


Coil
Current/Power

ADC

*
*
AC/5.5W
DC/5.5W
*AC/2.5W DC/3.5W
AC/8W DC/10W

Orifice

0.8

1.2

1.6

2.0

2.4

3.0

25

20

15

11

30

22

17

12

10

25

20

15

11

20

18

12

1.4

2.2

3.0

3.5

Flow factor Kv(L/min) 0.6

* These are not applicable for NO through base valves

Protection class IP65

Dimensions
*Pressure separation plug can be ordered on request.

1.22

GEM-SOL Index
GEM-SOL Direct Operated TYPE V 2/2 Way, 3/2 Way NC, NO

2W NC

2W NO through base

3W NC/NO

3W NO through base

GEM-SOL Direct Operated TYPE VL 2/2 Way, 3/2 Way NC, NO


VL BASE

Ex (NC)
In (NO)

IN (NC)
Ex (NO)

2W NC (forge)

3W NC/NO
6.2
TYPx2

TYPE V

TYPE V

Mazak

Brass

24

24

(1)

(2)

4.5
TYPx2

A
GEM-SOL

64

GEM-SOL

A
62

62
10.25

TYPE VL
61.6

9.5
TYPX2

24

3W NO through base

24

2W/3W NC (forge)

Aluminium / Stainless Steel


24

Brass Forging

32

24
4

4.3
TYPX2

1/8 BSP/NPT

65.2

72.4

10.25

GEM-B-31
24V 50Hz 8W

17

15

GEM-B-31
24V 50Hz 8W

32

32

32

1.23

32

4.3
TYPX4

GEM-SOL Index
GEM-V - MANIFOLD
How to Order Table applying to all the valves being of identica
GEM-V

No.of
valves

No. of
stations

Port

Specify
quantity

Specify
quantity

1/8" BSP 10
1/8" NPT 11

Without
manifold

Body
Mazak
Brass
St. St.

Function
1
2
3

2W NC
2W NO
2W NO*
3W NC
3W NO
3W NO*

1
2
2a
3
4
4a

1
2
3
4
5
6

0.8
1.2
1.6
2.0
2.4
3.0

Manual
Override

Seals

Orifice

N
V
E

NBR
Viton
EPDM

None
Plastic
Slot
Knob
push
push
lock

*supply pressure through base

0
1
2
3
4
5

Example : GEM-V-6/6-10132V2-220
Is a GEM-SOL direct operated sub-base
'V' type, 1/8" BSP with Mazak body, 3WNC
1.2, Viton seals, slot M/O, 12V AC 8W 60Hz
without connector.

Voltage
W/out coil
6
12
24
48
110
120
230
240
other

0
1
2
3
4
5
6
7
8
9

Power
No coil
AC8W 50Hz
AC8W 60Hz
DC10W
AC5.5W 50Hz
AC5.5W 60Hz
AC 2.5W
DC 5.5W
DC 3.5W

Connector
0
1
2
3
4
5
6
7
8

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub
other

0
1
2
3
4
5
9

GEM-V

How to Order Table specifying individual valves with own indepe


GEM-V

No. of
stations

No.of
valves

Body

Port

Function

Manual
Override

Seals

Orifice

Voltage

Power

Connector

As above table

Specify
quantity

Specify
quantity

Specify
quantity

Specify
quantity 0

Specify
quantity

Specify
quantity

Example :
GEM-V-2/6-10132N0-221

Is a GEM-SOL direct operated sub-base Type V of which:


2/6 stations with 1/8" BSP Mazak body, 3W NC, 1.2 orifice, NBR seal
no manual override, 12V AC 8W 60Hz with

GEM-V-3/6-10142N0-221

3/6 stations with 1/8" BSP Mazak body, 3W NO, 1.2 orifice, NBR seal
no manual override, 12V AC 8W 60Hz with

GEM-V-1/6-10112N0-221

1/6 stations with 1/8" BSP Mazak body, 2W NC, 1.2 orifice, NBR seal
no manual override, 12V AC 8W 60Hz with

VALVES only
How to Order Table for GEM-V-Body
GEM-V-Body

Body

Port
1/8" BSP 10
1/8" NPT 11

Mazak
Brass
St. St.

Function
1
2
3

2W NC
2W NO
2W NO*
3W NC
3W NO
3W NO*

1
2
2a
3
4
4a

1
2
3
4
5
6

0.8
1.2
1.6
2.0
2.4
3.0

Manual
Override

Seals

Orifice

N
V
E

NBR
Viton
EPDM

0
1
2
3
4
5

None
Plastic
Slot
Knob
push
push
lock

*supply pressure through base

Example : GEM-V-Body-10132V2-220
Is a GEM-SOL direct operated 'V' type valve:
1/8" BSP with Mazak body, 3WNC, 1.2, Viton seals,
slot M/O, 12V AC 8W 60Hz without connector.

Voltage
W/out coil
6
12
24
48
110
120
230
240
other

Power

0
1
2
3
4
5
6
7
8
9

No coil
AC8W 50Hz
AC8W 60Hz
DC10W
AC5.5W 50Hz
AC5.5W 60Hz
AC 2.5W
DC 5.5W
DC 3.5W

Connector
0
1
2
3
4
5
6
7
8

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub
other

0
1
2
3
4
5
9

How to Order Table for GEM-VL


* Manifolds are not available for VL valves
GEM-VL

Port
1/8" BSP 10
1/8" NPT 11

Body
Brass

Function
2

2W NC
2W NO
2W NO*
3W NC
3W NO
3W NO*

1
2
2a
3
4
4a

Orifice
0.8
1.2
1.6
2.0
2.4
3.0

1
2
3
4
5
6

Manual
Override

Seals
NBR
Viton
EPDM

*supply pressure through base

N
V
E

None
Plastic
Slot
Knob
push
push
lock

Example :
GEM-VL-211N0-221
Is a GEM-SOL direct operated Type VL valve :
Brass body, 2W NC, 0.8 orifice, NBR seals, no manual override,
12V AC 8W 60Hz with connector.

1.24

0
1
2
3
4
5

Voltage
W/out coil
6
12
24
48
110
120
230
240
other

0
1
2
3
4
5
6
7
8
9

Power
No coil
AC8W 50Hz
AC8W 60Hz
DC10W
AC5.5W 50Hz
AC5.5W 60Hz
AC 2.5W
DC 5.5W
DC 3.5W

Connector
0
1
2
3
4
5
6
7
8

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub
other

0
1
2
3
4
5
9

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL LPG
1/4", 3/8", 1/2" 2/2 Way NC, NO
General Description
GEM-SOL LPG 2/2 way NC, NO direct operated
solenoid valves have been specially designed for
use in LP gas systems.
They can also be used for air, water and vacuum
systems where high flow at low pressure is required

Notes
To order valves manufactured to your
specific requirements, please contact
our technical sales department.
Latch valves are available upon request.

2W NC

GEM-L

Body
Brass
St. st

Port
2
3

1/4"BSP
1/4"NPT
3/8"BSP
3/8"NPT
1/2"BSP
1/2"NPT

Seals

Function
20
21
30
31
40
41

2W NC
2W NO

1
2

NBR
Viton
EPDM

1.25

2W NO

Voltage
N
V
E

W/out coil
6
12
24
48
110
120
230
240
other

Connector

Power
0
1
2
3
4
5
6
7
8
9

No coil
AC8W 50Hz
AC8W 60Hz
DC10W

0
1
2
3

without
with
with LED
with bi
color LED
flying leads coil
with 1/2" Hub
surge protection
with LED
other

0
1
2
3
4
5
6
9

GEM-SOL Index
Technical Specifications
Pressure and flow table NC, NO

Function:

2/2 Way NC

Ports size:

1/4", 3/8", 1/2" BSP & NPT

Pressure and flow:

See table

Temperature range:

Fluid: 80 C max.

Size
1/4"

Ambient: -10 C to 50 C
Materials in contact
with fluid:

Pressure (bar)
Orifice AC DC NO Kv(L/Min)
1.5 0.7 0.5
12
8

3/8"

1.5

0.7

0.5

16

1/2"

12

0.8

0.4

0.3

35

Main valve:
Brass - hot stamping
Stainless steel 316
Solenoid Operator:
Stainless steel 300 & 400 series
Seals:
NBR, Viton, EPDM

Coil Voltage:

All Baccara coils voltages 10%


AC 8W
DC 10W
Protection class IP65 with connector

Size

B1

1/4"-3/8" 58

82

85

22

32

62 1/4"-3/8"BSP/NPT 11

85

97

27

38

65

1/2"

69

1/2"BSP/NPT

Weight
with coil

M5x0.8 22

394g

13.5 M5x0.8 22

484g

Dimensions

2W NC

2W NO

1.26

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL LPG
3/4", 1" 2/2 Way NC
General Description
GEM-SOL LPG 2/2 way NC direct operated
solenoid valves have been specially designed for
use in LP gas systems.
They can also be used for air, water and vacuum
systems where high flow at low pressure is required

Notes
To order valves manufactured to your
specific requirements, please contact
our technical sales department.

How to Order
Example : GEM-L-2501N-311
Is a GEM-SOL LPG, Brass, 3/4" BSP, 2WNC
NBR seals, 24V AC 40W Hz with connector.

GEM-L

Body
Brass
St. st

Port
2
3

3/4"BSP
3/4"NPT
1"BSP
1"NPT

Seals

Function
50
51
60
61

2W NC

NBR

1.27

Voltage
N

W/out coil
12
24
230

Connector

Power
0
2
3
7

No coil
AC40W 50Hz
DC36W

0
1
3

without
with
with LED
with bi
color LED
flying leads coil
with 1/2" Hub
surge protection
with LED
other

0
1
2
3
4
5
6
9

GEM-SOL Index
Technical Specifications
Function:

2/2 Way NC

Ports size:

3/4", 1" BSP & NPT

Pressure and flow:

See table

Temperature range:

Fluid: -10C - 80 C

Pressure and flow table

Ambient: -10 C to 50 C

Size

Orifice

3/4"

20

1"

25

(mm)

Pressure
(bar)

Kv(L/Min)

80

-1 to 1

125

Materials in contact :
Main valve :

with fluid

Brass - hot stamping, upon request


St.st.316
Solenoid Operator:
Stainless steel 300 & 400 series
Seals:
NBR
Coil voltage:

All Baccara coils voltages 10%


AC 40W
DC 38W
Protection class IP65 with connector

Dimensions
Size
3/4"
1"

90

55 119.5 17 3/4" BSP/NPT 87.7

100 65 128.5 21

1" BSP/NPT

92.7

weight
with coil

87.7
92.7

46
55

GEM-B-31
24V 50Hz 8W

B
F

1.28

SV-03-10

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Pilot Operated 1/4", 3/8", 1/2", 3/4", 1"


2/2 Way NC, NO
General Description
GEM-SOL Pilot Operated 2/2 way NC, NO solenoid
valves are recommended for applications where high flow
at high pressure is required.
The modular concept of the valve allows many
combinations and variations to meet different requirements
and fluid compatibility. The design is compact with high
flow rates, long life and low maintenance.

Typical Applications
Process systems
Water or sewage treatment
Industrial and irrigation applications
General purpose applications, such as oil,
gas systems, autoclaves etc.

Notes
The working pressure is 12 bar. On certain models,
valves for higher pressure up to 20 bar are available.
A minimum pressure of 0.3 or 0.5 is required.
Valves without tube are less manual override.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.
Latch valves are available upon request.
Available options:
Low power coils
Explosion-proof coils
A slow closing system to prevent a water
hammer effect.

NC

without tube

1.29

GEM-SOL Index

GEM-S

Body
Brass
St.st

GEM-S

Port
2
3

Body
Brass
St.st

1/4"BSP
1/4"NPT
3/8"BSP
3/8"NPT
1/2"BSP
1/2"NPT
3/4"BSP
3/4"NPT
1"BSP
1"NPT

Function
20
21
30
31
40
41
50
51
60
61

Port
2
3

1/2"BSP
1/2"NPT
3/4"BSP
3/4"NPT

1
2W NC
2W NO(2) 2
2a
2W NO
w/o tube(1)

NBR
Viton
EPDM

N
V
E

None
Slot
Knob

0
2
3

(1)option 2a is without manual override


(2)option available in GEM-S-

Function
40r
41r
50r
51r

Manual
Override

Seals

1
2W NC
2a
2W NO
w/o tube*

Manual
Override

Seals
NBR
Viton
EPDM

20...41

N
V
E

None
Slot
Knob

*option 2a is without manual override

1.30

0
2
3

Voltage
W/out coil
6
12
24
48
110
120
230
240
other

0
1
2
3
4
5
6
7
8
9

Voltage
W/out coil
6
12
24
48
110
120
230
240
other

0
1
2
3
4
5
6
7
8
9

Power
No coil
AC8W 50Hz
AC8W 60Hz
DC10W

Connector
0
1
2
3

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub

0
1
2
3
4
5

surge protection 6
with LED
other
9

Power
No coil
AC8W 50Hz
AC8W 60Hz
DC10W

Connector
0
1
2
3

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub

0
1
2
3
4
5

surge protection 6
with LED
other
9

GEM-SOL Index
Technical Specifications
Function:

2/2 Way NC & NO

Ports size:

1/4", 3/8", 1/2", 3/4", 1" BSP & NPT

Pressure and flow:

See table

Temperature range:

Fluid: -10C to 80 C

Size

Orifice
(mm) Pressure Kv(L/Min)

1/4"

Ambient: -10 C to 50 C
Manual Override:

Pressure and flow table NO/NC


GEM-S- -20...41

NC/NO - Brass screw


NOa - without manual override

12

3/8"

1/2"

12

0.5 - 20

16
35

Materials in contact :

with fluid

Pressure and flow table NO/NC


GEM-S- - r

Main valve :
Brass - hot stamping, upon request
dezinced brass (Cz132), St.st.316

Size

Orifice
(mm)

Solenoid Operator:

1/2"

16

3/4"

16

Stainless steel 300 & 400 series

Kv(L/Min)

Pressure

60

0.5 - 20

80

Seals:
NBR, Viton, EPDM
Coil voltage:

Pressure and flow table NO/NC


GEM-S- - 50...60

All Baccara coils voltages 10%


AC 8W

Orifice Kv Pressure range


Port
AC
DC
Connection (mm) (L/Min)

DC 10W
Protection class IP65 with connector

Weight
(gf)
*less coil

3/4"

20

130

0.3-15 0.3-15

1"

25

200

0.5-15 0.5-15 1050

760

* Coil weight approx. 110(gf), connector approx. 25 (gf)

Dimensions
Port Size

32 55

32

17

15

25

103

1" BSP/NPT 100 112.5 38.5 65

34

21

16 29.5 109.50

3/4" BSP/NPT 90

1.31

B
106

GEM-SOL Index

Port Size

1/4"- 3/8"

58

89

22

32

62 BSP/NPT

125

11

1/2"

70

95

27

38

70

1/2
BSP/NPT

135

13.5

weight
with coil

M5X0.5

22

466g

M5X0.8

22

562g

1/4-3/8

NO

NC / NOa
M5 DEEP 8
TYPx2

22

22

108.1

Manual
Override

18

1/2 or 3/4 BSP/NPT

70

35
44
67.6

GEM -

r 16mm orifice
NC / NOa

1.32

SV-05-10

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Pilot Operated Manifold


1/4", 3/8", 1/2" 2/2 Way NC, NO
General Description
GEM-SOL Pilot Operated 2/2 way NC, NO manifolds
are recommended for applications where high flow
at high pressure is required.
The modular concept of the valve allows many
combinations and variations to meet different requirements
and fluid compatibility. The design is compact with high
flow rates, long life and low maintenance.

Notes
The working pressure is 12 bar. On certain models,
valves for higher pressure up to 20 bar are available.
A minimum pressure of 0.3 or 0.5 bar is required.
Valves without tube are less manual override.
Latch valves are available upon request.
Available options:
Low power coils
Explosion-proof coils
A slow closing system to prevent a water
hammer effect.
Stations on the manifold are easily attached by 3 screws.
End stations are either with ports or plugged.
When using a manifold with more than 8 stations, it is
advisable to use two pressure supplies, one at each end.
Pressure separation plug can be ordered.
A combination of functions on the manifold is available.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

No. of
GEM-SM stations
specify
quantity

Body
Brass
St.st

2
3

Port
1/4"BSP
1/4"NPT
3/8"BSP
3/8"NPT
1/2"BSP
1/2"NPT

Seals

Function
20
21
30
31
40
41

1
2W NC
2
2W NO
2a
2W NO
w/o tube*

NBR
Viton
EPDM

*option 2a is without manual override

1.33

N
V
E

Manual
Override
None
Slot
Knob

0
2
3

Voltage
W/out coil
6
12
24
48
110
120
230
240
other

0
1
2
3
4
5
6
7
8
9

Power
No coil
AC8W 50Hz
AC8W 60Hz
DC10W

Connector
0
1
2
3

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub

0
1
2
3
4
5

surge protection 6
with LED
9
other

GEM-SOL Index
Technical Specifications
Pressure and flow table

Function:

2/2 Way NC & NO

Ports size:

1/4", 3/8", 1/2" BSP & NPT

Pressure and flow:

See table

Temperature range:

Fluid: -10C to 80 C

Orifice

1/4"

1/2"

Ambient: -10 C to 50 C
Manual Override:

Size

(mm)

Pressure

Kv(L/Min)

12
0.5 - 20

12

35

NC/NO - Brass screw


NOa - without manual override

Materials in contact :

Main valve :

with fluid

Brass - hot stamping


St.st.316
Solenoid Operator:
Stainless steel 300 & 400 series
Seals:
NBR, Viton, EPDM

Coil voltage:

All Baccara coils voltages 10%


AC 8W
DC 10W
Protection class IP65 with connector

1/4"

36+34xN 99

57

80

18

34

1/2"

40+40xN 112.8 67 83.9 20

40

Size

1/4
3/8
BSP/NPT BSP/NPT
1/2
3/4
BSP/NPT BSP/NPT

14

19

25

25

21

26

32

32

N - Number of stations

Dimensions

H
TYPx2

G
A

1.34

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Zero Differential Pressure


1/4", 3/8", 1/2", 3/4", 16mm 2/2 Way NC, NO
General Description
GEM-SOL Zero differential pressure 2/2 way NC and NO
solenoid valves are recommended for heavy duty
applications where high flow is required.
They can be operated with zero differential pressure
up to 14 bars.
The valves main advantage is in applications where
the pressure values can vary from a very low pressure
to a few bars and where high flow is needed.

Notes
Maximum pressure for use at nominal
voltage +10%. For further information,
please consult our engineers.
When switching from an AC coil to a DC
coil, the solenoid operator must be
changed.
Can be used in vacuum application
from -1 bar to maximum pressure (as in
pressure and flow table).

GEM-Z r

GEM-Z

Body
Brass
St.st.
Nylon (1)

Port
2
3
4

1/4"BSP
1/4"NPT
3/8"BSP
3/8"NPT
1/2"BSP
1/2"NPT
1/2"BSP
1/2"NPT
3/4BSP
3/4NPT(3)

Function
20
21
30
31
40
41
40r
41r
50r
51r

2W NC
2W NO(2)

1
2a

Seals
NBR
Viton
EPDM

1 : 3/8" & 1/2" only


2 : NO function without manual override
3 : 16mm orifice

1.35

Voltage
N
V
E

W/out coil
6
12
24
48
110
120
230
240
other

Power
0
1
2
3
4
5
6
7
8
9

No coil
AC8W 50Hz
AC8W 60Hz
DC10W

Connector
0
1
2
3

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub
surge protection
with LED
other

0
1
2
3
4
5
6
9

GEM-SOL Index
Technical Specifications
Pressure and flow table NC

Function:

2/2 Way NC & NO

Ports size:

1/4", 3/8", 1/2", 3/4" BSP & NPT

Pressure and flow:

See table

Temperature range:

Fluid: 80C max.


Ambient: -10 C to 50 C

Materials:

Main valve:
Brass, St.st. (1/4, 3/8, 1/2, 3/4)

Size

Orifice

1/4"

0-14

0-7

18

3/8"

12

0-14

0-8

50

1/2"

16

0-14

0-8

60

3/4"

16

0-14

0-8

80

(mm)

Pressure
AC
DC

Kv(L/Min)

Nylon (1/4, 3/8, 1/2)

Pressure and flow table NO

Solenoid operator:
Stainless steel 300 & 400 series

Size

Orifice

1/4"

0-8

0-8

18

3/8",1/2"

12

0-8

0-8

50

(mm)

Seals:
NBR, Viton, EPDM
Media:

Air, Inert gas, water

Coil voltage:

All Baccara coils voltages + 10%

Pressure
AC
DC

Kv(L/Min)

AC 8W, DC 10W

Dimensions
415g

3/8"

22 22 38 70 95 3/8" BSP/NPT

530g

1/2"

22 22 38 70 95 1/2" BSP/NPT

530g

1/2" or 3/8"

22 22 32 58 89 1/4" BSP/NPT

D E

95.4

1/4"

13

GEM-Z-4....
Nylon Valve Body

Weight
with coil

Size

70

42.5
67.4

GEM-Z- - r
16mm orifice - 1/2", 3/4"

1/2 or
3/4BSP/NPT

1.36

SV-05-10

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Zero Differential Pressure


3/4", 1" 2/2 Way NC
General Description
GEM-SOL Zero differential pressure 2/2 way NC
solenoid valves are recommended for heavy duty
applications where high flow is required.
They can be operated with differential pressure up
to 14 bar.
The valves' main advantage is in applications where
the pressure values can vary from a very low pressure
to a few bars and where high flow is needed.

Notes
Maximum pressure for use at nominal
voltage +10%.
When switching from an AC coil to a DC
coil, the solenoid operator must be
changed too.
Can be used in vacuum application
from -1 bar to maximum pressure (as in
pressure and flow table).
For further information, please consult
our engineers.

NO

NC

How to Order
Example : GEM-Z-2601N-231
Is a GEM-SOL Zero differential, Brass, 1" BSP, 2WNC,
NBR, 12V DC 36W with connector.

GEM-Z

Body
Brass
St. st.

Port
2
3

3/4"BSP
3/4"NPT
1" BSP
1" NPT

Function
50
51
60
61

2W NC
2W NOa

Seals
1
2

NBR
EPDM

1.37

Voltage
N
E

W/out coil
12
24
230

Power
0
2
3
7

No coil
AC40W 50Hz
DC36W

Connector
0
1
3

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub
surge protection
with LED
other

0
1
2
3
4
5
6
9

GEM-SOL Index

AC / DC

46

55

1.38

SV-03-10

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Pilot Operated 3/4", 1"


2/2 Way NC, NO
General Description
GEM-SOL pilot operated 2/2 way valves are
recommended for applications where high
flow and high pressure are required.
The flow adjustment screw enables restriction
of flow or emergency close-down.

Notes
A minimum differential pressure of 1 bar
is required for operation.
1" valves are with male threaded ports.
When assembling valve, take care not to
tighten pipe connections excessively.
Contact our technical sales department for
details on external pilot operation. This makes
it possible to separate between operating media
and the media in use.
Valves for low pressure 0.2 - 10 bar are available.

How to Order
Example : GEM-S-4501N-311
Is a GEM-SOL Pilot operated, nylon, 3/4" BSP,
2WNC, NBR seals, 24V AC 8W 50 Hz with connector.

GEM-S

Body
Nylon

Port
4

3/4"BSP
3/4"NPT
1"BSP
1"NPT

Function
50
51
60
61

2W NC
2W NO

Seals
1
2

NBR

1.39

Voltage
N

W/out coil
6
12
24
48
110
120
230
240
other

Power
0
1
2
3
4
5
6
7
8
9

No coil
AC8W 50Hz
AC8W 60Hz
DC10W

Connector
0
1
2
3

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub
surge protection
with LED
other

0
1
2
3
4
5
6
9

GEM-SOL Index
Technical Specifications
Pressure and flow table

Function:

2/2 Way NC, NO

Temperature range:

Fluid: 80 C max.

Size

Orifice

Pressure

Kv(L/Min)

Ambient: -10 C to 50 C

3/4"

25

1-10

136

1"

25

1-10

200

Materials :

Body and cover:


Glass reinforced Nylon
Diaphragm:
Reinforced NBR
Internal trim:
Stainless steel, Acetal, reinforced nylon

Manual override:

Brass screw
Flow adjusted by flow control handle.

Weight::

450 gr.

Media:

Air, water, inert gas

Mounting:

On pipe in any position

Coil Voltage:

All Baccara coils voltages 10%


AC 8W

DC 10W

Protection class IP65 with connector

Dimensions

1
BSP/NPT

3/4" BSP/NPT

1.40

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Pilot Operated 1/4", 3/8", 1/2"


3/2 Way NC, NO
General Description
GEM-SOL Pilot operated 3/2 way NC or NO
solenoid valves are designed for applications
where high flow is required.
They can be operated from a low pressure of
0.8 up to 12 bar.
They can be used for industrial and irrigation
control and automation systems. These valves
are suitable to work with air, water and oil; please
consult with us if you need the valves to work
with other fluids.

Notes
Supply piping must be at least the same size
as the port, and unrestricted. Install flow
controls in cylinder line only.
For pressure higher than 12 bar, please
consult our engineers.

How to Order
Example : GEM-S-2204V21-311
Is a GEM-SOL pilot operated Brass, 1/4" BSP,
NO, Viton, slot manual override with bracket,
24V AC 8W 50 Hz with connector.

GEM-S

Body
Brass

Port
2

1/4"BSP
1/4"NPT
3/8"BSP
3/8"NPT
1/2"BSP
1/2"NPT

Function
20
21
30
31
40
41

NC
NO

3
4

NO

Manual
Override

Seals
NBR
Viton
EPDM

N
V
E

None
Slot
Knob
Hydraulic

0
2
3
4*

Bracket
without
with

* for NC application

1.41

NC

0
1

Voltage
W/out coil
6
12
24
48
110
120
230
240
other

0
1
2
3
4
5
6
7
8
9

Power
No coil
AC8W 50Hz
AC8W 60Hz
DC10W

Connector
0
1
2
3

without
with
with LED
with bi color
LED
flying leads
coil

0
1
2
3

with 1/2" Hub

surge protection 6
with LED
9
other

GEM-SOL Index
Technical Specifications
Pressure and flow table
Size

Pressure

1/4"

Kv(L/Min)
18

0.8 -12

3/8", 1/2"

Dimensions
Size

50

Mounting Bracket
B

1/4"

124.5

58

25 32.5 1/4"

3/8", 1/2"

134

69

30 32.5 1/2"

Weight
with coil

M4x0.7
Deep 6
M5x0.8
Deep 7

32

540g

1/4"

15

38

758g

3/8", 1/2"

20

Size

25

11

14

20

25

32

30

13

22

25

33

40

1.42

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL General Purpose Pilot Operated


1/4", 3/8", 1/2" 3/2 Way
General Description
GEM-SOL 3/2 Way general purpose pilot operated
valves are recommended for applications where
high flow at high pressure is required.
They can be used in control and automation systems,
with different media fluids for the pilot and the line.
The typical applications are: industrial furnace, heating
equipment, burners, oil and gas, autoclaves, dental
equipment, instrumentation, car washers, machine
industries and irrigation.
Pilot pressure

Notes
Pilot pressure should be at least 1.5 bar.
To order valves manufactured to your
specific requirements, please contact our
technical sales department.

How to Order
Example : GEM-SE-2209N-331
Is a GEM-SOL general purpose pilot operated,
Brass 1/4" BSP 3W with NBR seals, 24V DC 10W with
connector.

GEM-SE

Port

Body
Brass

1/4"BSP
1/4"NPT
3/8"BSP
3/8"NPT
1/2"BSP
1/2"NPT

Function
20
21
30
31
40
41

general
purpose

Seals
NBR
Viton
EPDM

Bracket
N
V
E

1.43

without
with

0
1

Power

Voltage
W/out coil
6
12
24
48
110
120
230
240
other

0
1
2
3
4
5
6
7
8
9

No coil
AC8W 50Hz
AC8W 60Hz
DC10W
AC5.5W50Hz
AC5.5W60Hz
DC5.5W

Connector
0
1
2
3
4
5
7

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub

0
1
2
3
4
5

surge protection 6
with LED
other
9

GEM-SOL Index
Technical Specifications
Function:

3/2 Way general purpose

Ports size:

1/4", 3/8", 1/2" BSP & NPT

Pressure and flow:

See table

Temperature range:

Pressure and flow table NC


Size

Orifice

Fluid: max 80 C

1/4"

Ambient: -10 C to 50 C

3/8"

12

1/2"

12

Materials in contact
with fluid :

Pressure

Kv(L/Min)

12
0 - 10

16
35

Main valve :
10

Minimum
Pilot Pressure

Brass -hot stamping


Spring - AISI -302
Solenoid Operator:
Stainless steel 300 & 400 series
Seals:
NBR, Viton, EPDM

6
4
2
0
-1

Piston seal PU(1)


Media:

10

Line Pressure

Air, gas, water, fuel, oil etc


(1) other seals available upon request

Mounting Bracket
Size

1/4"

34

32

32.5

1/4"

3/8",1/2"

45

38

41

3/8", 1/2"

141.5 45.6
155

45.6

Size

M4 37.5

25

58

1/4"

15

M5

30

69

47

3/8", 1/2" 20

25 4.5 11

14

20

25

32

30

22

25

33

40

13

Dimensions

G Deep K

1.44

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL General Purpose Direct Operated


1/4", 3/8", 1/2", 3/4" 3/2 Way
General Description
GEM-SOL 3/2 Way general purpose direct operated
valves are recommended for applications where high
flow at high pressure is required.
They can be used in control and automation systems,
with different media fluids for the pilot and the line.
The typical applications are: industrial furnace, heating
equipment, burners, oil and gas, autoclaves, dental
equipment, instrumentation, car washers, machine
industries and irrigation.

Notes
For 3/8 to 3/4" valves: coils available
in DC 12, 24, 38W and in AC 24, 230
AC 36W 50Hz.
To order valves manufactured to your
specific requirements, please contact
our technical sales department.

How to Order
Example : GEM-X-2209N0-331
Is a GEM-SOL general purpose
direct operated, Brass 1/4" BSP 3W
general purpose with NBR seals,without
bracket, 24V DC 10W with connector.

GEM-X

Body
Brass

Port
2

1/4"BSP
1/4"NPT
3/8"BSP
3/8"NPT
1/2"BSP
1/2"NPT
3/4"BSP
3/4"NPT

1/4", 3/8", 1/2" 3W

Function
20
21
30
31
40
41
50
51

general
purpose

Seals
NBR
EPDM

N
E

Note:
(1) Bracket not available in 3/4"
(2) For 3/8" to 3/4" valves: coils available in DC 12, 24, 38W
and in AC 24, 230 AC 36W 50Hz
1/4" port - available in all voltages

1.45

Bracket(1)
without
with

0
1

3/4" 3W

Power (2)

Voltage
W/out coil
6
12
24
48
110
120
230
240
other

0
1
2
3
4
5
6
7
8
9

No coil
AC8W 50Hz
AC8W 60Hz
DC10W
DC38W
AC40W50Hz

Connector
0
1
2
3
5
4

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub

0
1
2
3

surge protection
with LED

other

4
5

GEM-SOL Index
Technical Specifications
Pressure and flow table NC

Function:

3/2 Way general purpose

Ports size:

1/4", 3/8", 1/2", 3/4" BSP & NPT

Size

Orifice

(mm)

Pressure

Pressure and flow:

See table

1/4"

-1 to 3

12

Temperature range:

Fluid: max 80 C

3/8"

12

-1 to 5

16

1/2"

12

-1 to 5

35

3/4"

19

-1 to 3

130

Ambient: -10 C to 50 C
Materials in contact
with fluid :

Kv(L/Min)

Main valve :
Brass -hot stamping
Solenoid operator:
Stainless Steel 300 & 400 series
Seals:
NBR, EPDM

Media:

Air, gas, water, fuel, oil etc

Mounting Bracket
Size

1/4"

15

3/8", 1/2" 20

25 4.5 11

14

20

25

32

30

22

25

33

40

13

Dimensions
Size
1/4"

118.5 58

3/8"-1/2" 147.8 69 30

41

M.4x0.7
Deep 6
M.5x0.8
Deep 7

32

32

45.9

38

45

59.7

25 32.5 1/4"
3/8"
1/2"

1/4", 3/8", 1/2" 3W


3/4" 3W

GEM-B-31
24V 50Hz 8W

GEM-B-31
24V 50Hz 8W

1.46

SV-05-10

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Low Pressure Pilot Operated


3/4", 1" 2/2 Way NC
General Description
GEM-SOL 2/2 way NC low pressure pilot operated
valves are recommended for applications where high
flow and varied pressure range are required.

Notes
1" valves are with male threaded ports.
When assembling valve, take care not to
tighten pipe connections excessively.
Valves are controlled by 3/2 way NO valve.

Pilot
pressure

How to Order
Example : GEM-Z-4501N-311
Line
pressure

Is a GEM-SOL Pilot operated, nylon, 3/4" BSP,


2WNC, NBR seals, 24V AC 8W 50 Hz with connector.

GEM-Z

Body
Nylon

Port
4

3/4"BSP
3/4"NPT
1"BSP
1"NPT

Function
50
51
60
61

2W NC

Seals
1

NBR

1.47

Voltage
N

W/out coil
6
12
24
48
110
120
230
240
other

Power
0
1
2
3
4
5
6
7
8
9

No coil
AC8W 50Hz
AC8W 60Hz
DC10W

Connector
0
1
2
3

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub

0
1
2
3
4
5

surge protection 6
with LED
other
9

GEM-SOL Index
Technical Specifications
Function:

2/2 Way NC

Temperature range:

Fluid: 80 C max.

Pressure and flow table

Ambient: -10 C to 50 C
Materials :

Body and cover:


Glass reinforced Nylon

Kv(L/Min)

25

Line
Pressure
0.2 to 10

25

0.2 to 10

200

Size

Orifice

3/4"
1"

136

* Pilot pressure should be at least


1 bar higher than line pressure

Diaphragm:
Reinforced NBR
Internal trim:
Stainless steel, Acetal, reinforced nylon
Manual override:

Brass screw
Flow adjusted by flow control handle.

Weight::

450 gr.

Media:

Air, water, inert gas

Mounting:

On pipe in any position

Coil Voltage:

All Baccara coils voltages 10%


AC 8W

DC 10W

Protection class IP65 with connector

115

Dimensions

65
95

1.48

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL High Pressure Pilot Operated


1/4", 3/8", 1/2", 3/4", 1" 2/2 Way NC, NO
General Description
GEM-SOL High Pressure pilot operated 2/2 Way NC and
NO solenoid valves are recommended for applications
where high flow at high pressure is required.
They can be used in control and automation systems.
The typical applications are: industrial furnace, heating
equipment, fog systems, burners, oil and gas, autoclaves,
dental equipment, instrumentation, car washers, machine
industries and irrigation.

Notes
A minimum pressure of 1 bar is required
for operation.
To order valves manufactured to your
specific requirements, please contact our
technical sales department.
Latch valves are available upon request.

How to Order
Example : GEM-HP-2201P-321
Is a GEM-SOL High pressure Pilot operated, Brass 1/4" BSP
2WNC, polyurethane seals, 24V AC 8W 60Hz with connector.

GEM-HP

Body
Brass
St.st

Function

Port
2
3

1/4"BSP
1/4"NPT
3/8"BSP
3/8"NPT
1/2"BSP
1/2"NPT
3/4"BSP
3/4"NPT
1"BSP
1"NPT

20
21
30
31
40
41
50
51
60
61

2W NC
2W NO

Seals
1
2

Polyurethane P
Viton
V
PTFE
T

1.49

Voltage
W/out coil
6
12
24
48
110
120
230
240
other

Connector

Power
0
1
2
3
4
5
6
7
8
9

No coil
AC8W 50Hz
AC8W 60Hz
DC10W

0
1
2
3

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub

0
1
2
3
4
5

surge protection 6
with LED
other
9

GEM-SOL Index
Technical Specifications
Pressure and flow table NC

Function:

2/2 Way NC and NO

Ports size:

1/4", 3/8", 1/2", 3/4", 1" BSP & NPT

Pressure and flow:

See table

Temperature range:

Fluid: max 80 C
Ambient: -10 C to 50 C

Materials in contact
with fluid :

Main valve :
Brass -hot stamping

Size

Orifice

1/4"

3/8"

(mm)

Pressure

Kv(L/Min)

12
16
1 - 60

1/2"

12

3/4"

19

130

1"

25

200

35

St.St. 316
Solenoid Operator:

Pressure and flow table NO

Stainless steel 300 & 400 series

Size

Orifice

1/4"

(mm)

Seals:
Polyurethane, Viton, PTFE
Coil voltage:

All Baccara coils voltages 10%


AC 8W

DC 10W

Protection class IP65 with connector

Pressure

Kv(L/Min)

12

3/8"

1/2"

12

3/4"

19

130

1"

25

200

16
1 - 30

35

Dimensions
Size

1/4"-3/8" 58

32

10.5

118

91.5

22

58.9

69

38

13

130

102.5

22

64.9

3/4"

90

55

17

140

73.1

1"

100

65

21

151

78.1

1/2"

A
B

1.50

SV-04-09

GEM-SOL Index

Technical Info

GEM-SOL Index

22

For taping screw


No. 4 x 1/2

1/4 BSP

10

22

40

66

19
30

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Chem-Sol 1/2"


2/2 Way NC
General Description
These GEM-SOL 2/2 way NC Chem-Sol
solenoid valves are recommended for use in
applications where corrosive fluid must be controlled,
such as in chemical process, water treatment, analysis
device etc.
They can be used in industrial and irrigation control
and automation systems.

Notes
Contact our technical department for more
information on valve and fluid compatibility.
To order valves manufactured to your
specific requirements, please contact
our technical department.
Specify if application is pressure or vacuum.
All valves are assembled with seal coil nut,
lower coil gasket and impregnated coil.
Options:
Supplied with mounting threads upon request.
Please specify when ordering.

vacuum

How to Order
Example : GEM-C-4011V-321
Is a GEM-SOL Chem-Sol, 1/2" BSP,
2WNC for vacuum, Viton seals, 24V AC
8W 60 Hz with connector.

GEM-C

Port
1/2" BSP
1/2" NPT

Function
40
41

2W NC

Flow direction

Pressure
Vacuum
Pressure

1
2

Seals
Viton
EPDM

1.53

Voltage
V
E

W/out coil
6
12
24
48
110
120
230
240
other

Connector

Power
0
1
2
3
4
5
6
7
8
9

No coil
AC8W 50Hz
AC8W 60Hz
DC10W
AC5.5W50Hz
AC5.5W60Hz

0
1
2
3
4
5

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub
surge
protection
with LED

0
1
2
3

other

4
5
6

GEM-SOL Index
Technical Specifications
Function:

2/2 Way NC

Ports size:

1/2" BSP & NPT

Orifice:

8mm

Kv:

18 L/min

Pressure:

See table

Temperature range:

Fluid: 5 C to max 50 C

Pressure Table - NC
Flow direction
not restricted

Flow direction
restricted

AC 8W

0 to 0.7 bar

Min.dp 0.3 bar

Vacuum Type Table - NC

Ambient: -10 C to 50 C
Materials:

Coil

Coil

Flow direction
not restricted

Flow direction
restricted

PVC

AC 8W

-1 to 0.5

-1 to 0.5

Diaphragm:

AC5.5W

-0.5 to 0.5

-0.8 to 0.5

DC10W

-0.4 to 0.5

-0.6 to 0.5

Main valve:

Viton, EPDM
Coil Voltage:

All Baccara coils voltages from -5% to +10%


AC 8W, 5.5W
DC 10W
Protection class IP65 with plug attached

Dimensions
22

M 4x0.7 Deep 10
TYPx2

87

22

(optional)

1/2" BSP Deep 15


both sides

32

62

1.54

SV-03-11

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Chem-Sol 3/4"


2/2 Way NC
General Description
These GEM-SOL 2/2 way NC Chem-Sol
solenoid valves are recommended for use in
applications where corrosive fluid must be controlled,
such as chemical process, water treatment, analysis
device etc.
They can be used for industrial and irrigation control
and automation systems.

Notes
Contact our technical department to
get details on valve and fluid compatibility.
To order valves manufactured to your
specific requirements, please contact
our technical department.
Specify if application is pressure or vacuum.

vacuum

How to Order
Example : GEM-C-5011V-311

Flow direction

Is a GEM-SOL Chem-Sol, 3/4" BSP,


2WNC for vacuum, Viton seals, 24V AC
18W with connector.

GEM-C

Port
3/4" BSP
3/4" NPT

Function
50
51

2W NC

Pressure
1

Vacuum
Pressure

Seals
1
2

Viton
EPDM

1.55

Voltage
V
E

W/out coil
24
110
230
other

Connector

Power
0
3
5
7
9

No coil
AC 18W
DC 38W

0
1
3

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub

0
1
2
3
4
5

surge
protection
with LED

other

GEM-SOL Index
Technical Specifications
Pressure Table - NC

Function:

2/2 Way NC

Ports size:

3/4" BSP & NPT

Orifice:

14mm

Kv:

40 L/min

Pressure:

See table

Temperature range:

Fluid: 5 C to max 50 C

Flow direction
not restricted

AC / DC

0 to 3 bar

Flow direction
restricted

Vacuum Type Table - NC

Ambient: 5 C to 50 C
Materials:

Coil

Coil

Flow direction
not restricted

Flow direction
restricted

AC / DC

-1 to 0.5

-1 to 0.5

Main valve:
PVC
Diaphragm:
Viton, EPDM

Coil Voltage:

All Baccara coils voltages from -5% to +10%


AC - inrush 65VA at 50 Hz
holding 32VA (18W) at 50Hz
DC -38W
Protection class IP65 with plug attached

Dimensions
55

18.5 TYPX2

106.5

46

NPT

3/4" BSP/NPT
Both sides
42
83

NPT

36

BSP

77

1.56

SV-03-10

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Pinch Valve


2/2 Way, NC
General Description
These GEM-SOL 2/2 way NC Pinch valve solenoid
valves are recommended for use in applications where
corrosive or contaminated fluid must be controlled.
They can be used for industrial, laboratories and
irrigation control and analysis devices.

Notes
The valve performances are a function of the
tube dimensions and hardness.
Please consult our technical sales department.
Maximum tube diameter: 9.5mm.
Valves are DC designated.
For AC, use rectifier connector.

GEM-P

Tube

Function

Voltage

Note:
(1)

1.57

Power

(1)

Connector

GEM-SOL Index
Technical Specifications
Function:

2/2 Way NC

Tubes:

6x4, 8x5, 9.5x6.5

Pressure range:

1 bar

Temperature range:

Fluid: according to tube specifications


Ambient: -10 to 50 C

Materials :

Valve:
Aluminium
Solenoid:
See GEM-SOL operator

Coil voltage:

All Baccara coils voltages 10%


DC10W,
DC14W - max 70% duty cycle, ton = 7 [min] max.
Protection class IP68 with plug attached

16

Dimensions
A

GEM-P-1

6.5

10

GEM-P-2..3

9.5

6.5

10

M4x0.7 DEEP 0.5

16

75

45.6

C
B
A

28

1.58

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Pinch Valve


3/2 Way
General Description
These GEM-SOL 3/2 way Pinch valve solenoid
valves are recommended for use in applications where
corrosive or contaminated fluid must be controlled.
They can be used for industrial, laboratories and
irrigation control and analysis devices.

Notes
The valve performances are a function of the
tube dimensions and hardness.
Please consult our technical sales department.
Valves are DC designated.
For AC, use rectifier connector.

How to Order
Example : GEM-P-13-381
Is a GEM-SOL Pinch valve for 6x4 silicon
tube, 3W, 24V DC 14W with connector.

GEM-P

Tube
6x4

Function
1

3W

Voltage
3

6
12
24
48
110
120
230
240
other

Power
1
2
3
4
5
6
7
8
9

1.59

DC14W

Connector
8

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub

0
1
2
3

surge protection
with LED
other

4
5

GEM-SOL Index
Technical Specifications
Function:

3/2 Way

Tubes:

6x4

Pressure range:

1 bar

Temperature range:

Fluid: according to tube specifications


Ambient: -10 to 50 C

Materials in contact:

Valve:
Aluminium
Solenoid:
See GEM-SOL operator

Coil voltage:

All Baccara coils voltages 10%


DC10W,
DC14W - max 70% duty cycle, ton = 7 [min] max.
Protection class IP68 with plug attached

Dimensions

1.60

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

Long Distance Operating Solenoid


LDOS
General Description
The Long Distance Operating Solenoid makes
it possible to activate a solenoid valve by using
a small section conductor at a distance of up to
5 kms from the voltage source.
The valves' main advantage is the reduction in
conduit cost.
Allows use of a lower power source.
This device is supplied with GEM-SOL 3/2 Way
NC, NO heavy duty solenoid valve.
Specially suited for irrigation control.

Notes
This solenoid is designed to operate only
with a Baccara valve.
To order valves manufactured to your
specific requirements, please contact our
technical sales department.

How to Order
Example : LDOS - 21034N0-11
Is a LDOS Brass, 1/8" BSP, 3WNC, 2.0 orifice,
NBR, no manual override, 24V AC with connector.

LDOS

Body
Brass
St.st

Port
2
3

1/8"BSP
1/8"NPT
1/4"BSP
1/4"NPT

Function
10
11
20
21

3W NC
3W NO

3
4

Orifice
1.6
2.0
2.4

Manual
Override

Seals
3
4
5

NBR
Viton
EPDM

1.61

N
V
E

None

Voltage
24V AC
12V DC

1
2

Connector
without
with

0
1

GEM-SOL Index
Technical Specifications
Voltage :

12V DC or 24V AC + 10% - 20%

Current :

Holding 15mA

Power:

0.3W

Delay Time:

See table

Connection:

DIN 43650 Connecting box

Ambient temp:

-10 C to 60C

Pressure Table
Function
3WNC

3WNO
Protection class IP65 with connector

Orifice

Pressure

1.6

16

2.0

10

2.4

1.6

16

2.0

12

2.4

Conduit
Delay time (Sec)
Distance
at a nominal voltage (Km) Section (mm)
2.4
0.5
4-5
4.8
1.0
7.5

1.5

Dimensions
22

2X M5x0.8
DEEP 8

22

37

68

(For illustrative purposes only)

8.3

81.2

81.5

GEM-SOL
VALVE

19
93.5

1.62

SV-04-09

GEM-SOL Index
BACCARA

GEM-SOL Long Distance Operator (LDO)


2/2, 3/2 Way, NC, NO
General Description
The Long Distance Operator makes it possible
to activate a solenoid valve by using a small
section conductor at a distance of up to
5 km from the voltage source.
The valves' main advantage is the reduction in
conduit cost.
Allows use of a lower power source.
This device is supplied with GEM-SOL 2/2 or 3/2 Way
NC, NO solenoid valve.
Specially suited for irrigation control.

Notes
This solenoid is designed to operate only
with a Baccara valve.
No manual override should be designated.
To order valves manufactured to your
specific requirements, please contact our
technical sales department.

How to Order
Example : GEM-LDO-9-GEM-A-21035NO
The GEM-LDO is attached to a GEM-SOL direct operated Brass,
1/8 BSP, 3W NC, 2.4 orifice, NBR with no manual override.
GEM-LDO

Voltage
24 VAC & 9
12-24 VDC

Please refer to the


How to Order
definitions of the product
that the GEM-LDO is
attached to.

1.63

Technical Info

GEM-SOL Index
Technical Specifications

-10C to 60C

Lead wire length - 28 cm


PVC coated. AWG 18 UL 1007

Epoxy

Voltage

Conduit
Distance
section (mm2)
(km)

12 / 24

12

24

Delay Time (sec)


On
Off
3

0.5

12

0.5

Dimensions

91

86

39

92

92

1.64

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Inline
1/8", 1/4" 2/2 Way NC , NO
General Description
This GEM-SOL solenoid valve is designed to be
mounted "IN LINE".
It is used mainly as a safety device on fuel systems
for motor vehicles. It can also be used in water, air
or oil systems.

Notes
Valves are inspected at general pressures
of 12 bar or less (see table). Valves for
higher pressures are available.
ADC valves are suitable to work only with
AC 8W or DC 10W coils.
Latch valves are available upon request.
Valves with 6mm orifice are DC only.
To order valves manufactured to your
specific requirements, please contact our
technical sales department.

GEM-I

Body
Hex.Brass 4
"Inline"
5
mounting

Port
1/8"BSP
1/8"NPT
1/4"BSP
1/4"NPT

Function
10
11
20
21

2W NC
2W NO

1
2

Orifice
0.8
1.2
1.6
2.0
2.4
3.0
4.0 *
6.0 *

For NO, the maximum


orifice size is 3mm

OUT

IN

IN

OUT

NO

NC

Voltage

Seals
1
2
3
4
5
6
7
8

NBR
Viton
EPDM

N
V
E

W/out coil
6
12
24
48
110
120
230
240
other

0
1
2
3
4
5
6
7
8
9

Power
0
No coil
AC8W 50Hz 1
AC8W 60Hz 2
3
DC10W
AC5.5W 50Hz 4
AC5.5W 60Hz 5
7
DC5.5W

Connector
without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub

1.65

4
5

surge protection 6
with LED
other

* Hex body

0
1
2
3

GEM-SOL Index
Technical Specifications
Max.Pressure (bar) 2W NC Table

Function:

2/2 Way NC & NO

Ports size:

1/8" and 1/4" BSP & NPT

Orifice:

See table

Kv:

See table

Pressure range:
Temperature range:
Materials :

Orifice

Coil
Current/Power

0.8

1.6

2.4

3.0

4.0

6.0

ADC

40

30

17

10

1.1

See table

AC/8W DC/10W

45

37

20

12

1.8

Fluid: max 80 C

AC 5.5

40

32

16

0.5

Ambient: -10 C to 50 C

DC 5.5

35

30

12

0.5

Main valve :

Flow factor Kv(L/min) 0.5

1.7

3.5

4.5

Brass
Solenoid Operator:
Stainless steel 300 & 400 series

Max.Pressure (bar) 2W NO Table


Orifice

Coil
Current/Power

Seals:
NBR, Viton or EPDM
Weight (with coil):

228 gr

Media:

Air, water, oil

Coil voltage:

All Baccara coils voltages 10%

0.8

1.6

2.4

3.0

ADC

32

27

13

AC/8W DC/10W

35

32

18

12

Flow factor Kv(L/min) 0.5

1.6

3.2

3.8

Size (G)

1/8"

20

16

68

1/4"

23

18

88

AC 8W, 5.5W and 2.5W &


DC 10W, 5.5W and 3.5W
Protection class IP65 with connector

Dimensions

Dimensions

61

31

1/8

1/8

38

49

1.66

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Direct Operated 2/2 Way NC


for Air conditioning systems
General Description
GEM-SOL 2/2 Way NC solenoid valves are
recommended for heavy duty applications where
high performance is required.
This valve series is specially designed for use with
refrigeration fluids in air conditioning systems.

Notes
ADC valves are suitable to work with
AC 8W or DC 10W coils.
To order valves manufactured to your
specific requirements, please contact our
technical sales department.

GEM-R

Body
Brass

Port
2

1/2"NF
Flare
5/8"NF
Flare
5/8" NF
O-ring

Function
1

2W NC

O-ring type

Orifice
2.4

Seals
5

N
NBR
Neoprene C

2
4

1.67

Flare type

Voltage
W/out coil
6
12
24
48
110
120
230
240
other

0
1
2
3
4
5
6
7
8
9

Connector

Power
No coil
AC8W 50Hz
AC8W 60Hz
DC10W

0
1
2
3

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub

0
1
2
3
4
5

surge protection 6
with LED
other
9

GEM-SOL Index
Technical Specifications
Function:

2/2 Way NC

Orifice:

See table

Kv:

See table

Pressure range:

See table

Temperature range:

Fluid: max 80 C

Max.Pressure (bar) 2W NC Table


Coil
Current/Power

Ambient: -10C to 50C


Materials :

Orifice
2.4

AC/8W DC/10W

30

Flow factor Kv(L/min)

3.5

Main valve :
Brass
Solenoid Operator:
Stainless steel 300 & 400 series
Seals:
NBR : for R-134a
NEOPRENE : for R12 & R22

Media:

Refrigeration fluids

Coil voltage:

All Baccara coils voltages 10%


AC 8W

DC 10W

Protection class IP65 with connector

Dimensions

O-ring type

Flare type

1.68

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Direct Operated Type NAMUR


3/2 Way NC
General Description
These GEM-SOL solenoid valves with NAMUR
plate are designed to be mounted on an appropriate
counterpart adapted to this valve type.
A close circuit system is also available for use
in contaminated installations.

Notes
Valves are inspected at general pressures
of 12 bar or less (see table). Valves for higher
pressure are available.
ADC valves are suitable to work only with
AC 8W or DC 10W coils.

GEM-N

Body
Alum.

Function
5

3WNC

Orifice
1.6
2.4

Manual
Override

Seals
3
5

NBR
Viton

N
V

None
Plastic
Slot
Knob

1.69

0
1
2
3

Voltage
W/out coil
6
12
24
48
110
120
230
240
other

0
1
2
3
4
5
6
7
8
9

Power
No coil
AC8W 50Hz
AC8W 60Hz
DC10W
AC5.5W50Hz
AC5.5W60Hz
AC2.5W
DC5.5W
DC3.5W

Connector
0
1
2
3
4
5
6
7
8

0
without
1
with
with LED
2
with bi color 3
LED
flying leads 4
coil
with 1/2" Hub 5
Ex proof
6
other
9

GEM-SOL Index
Technical Specifications
Function:

3/2 way NC

Orifice:

See table

Kv:

See table

Pressure range:

See table

Temperature range:

Fluid: max 80 C

Max.Pressure (bar) 2W NC Table


Coil
Current/Power

Orifice

1.6

2.4

ADC

15

AC/8W DC/10W

17

10

Ambient: -10C to 50C

AC/5.5W

15

Manual Override:

Plastic or Brass

AC/2.5W DC/5.5/3.5W

10

Materials :

Main valve :

Flow factor Kv(L/min)

1.7

3.5

Aluminium
Solenoid Operator:
Stainless steel 300 & 400 series
Seals:
NBR, Viton
Media:

Air

Coil voltage:

All Baccara coils voltages 10%


AC 8W, 5.5 and 2.5W &
DC 10W, 5.5 and 3.5W
Protection class IP65

Dimensions

1.70

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL External Pilot Operated


3/4", 1" 2/2 Way, NC
General Description
GEM-SOL 2/2 way, NC external pilot operated
valves are recommended for applications where
high flow and varied pressure range are required.

Notes
1" valves are with male threaded ports.
When assembling valve, take care not to
tighten pipe connections excessively.
Valves are controlled by external
3/2 way valve.

How to Order
Example : GEM-E-4501N
Is a GEM-SOL external pilot operated
nylon, 3/4" BSP, 2W NC with NBR seals.

GEM-E

Body
Nylon

Port
4

3/4" BSP
3/4"NPT
1" BSP
1"NPT

Function
50
51
60
61

2W NC

Seals
1

1.71

NBR

GEM-SOL Index
Technical Specifications
Functions:

2/2 Way NC

Temperature range:

Fluid: max 80 C

Pressure and flow table

Ambient: -10 to 50 C
Materials in contact:

Body and cover:


Glass reinforced nylon

Kv(L/Min)

25

Pressure
(bar)
0.2-10

25

0.2-10

200

Size

Orifice
(mm)

3/4"
1"

136

Note: Pilot pressure should be at least 1 bar


higher than process fluid.

Diaphragm:
Reinforced NBR
Internal trim:
Stainless steel, Acetal, reinforced nylon
Manual override:

Brass screw
Flow adjusted by flow control handle

Weight:

450 gr.

Media:

Air, water, inert gas

Mounting:

On pipe in any position

Dimensions

1.72

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL External Pilot Operated


1/4", 3/8", 1/2" 2/2, 3/2 Way, NO
General Description
GEM-SOL 2/2 way, NO external pilot operated
valves are recommended for applications where
high flow at high pressure is required.
They can be used in control and automation
systems.
The typical applications are: industrial furnace,
heating equipment, burners, oil and gas, autoclaves,
dental equipment, instrumentation, car washers,
machine industries and irrigation.
2W NO

Notes
Pilot pressure should be at least 1 bar
higher than process fluid.
To order valves manufactured to your
specific requirements, please contact
our technical sales department.
3/8 is not available for 3/2 way NO.
St.st. valves are available only in 2W.

3W NO

How to Order
Example : GEM-E-2202N-0
Is a GEM-SOL external pilot operated
Brass, 1/4" BSP, 2W NO with NBR seals, without
mounting bracket.

GEM-E

Port

Body (1)
Brass
St. St.

2
3

1/4" BSP
1/4" NPT
3/8" BSP
3/8" NPT
1/2" BSP
1/2" BSP

Function
20
21
30
31
40
41

2W NO
3W NO

2
4

(1) 3W NO - brass only


(2) Mounting bracket only
availabe for 3W NO

1.73

Seals
NBR

Bracket (2)
N

without
with

0
1

GEM-SOL Index
Technical Specifications
Pressure and flow table

Functions:

2/2, 3/2 Way NO

Ports size:

1/4", 3/8", 1/2" BSP & NPT

Pressure & flow:

See table

Temperature range:

Fluid: max 80 C
Ambient: -10 to 50 C

Materials in contact
with fluid:

Size

Orifice
(mm)

1/4"

3/8"

1/2"

12

Pressure
(bar)

Kv(L/Min)
12

0.5 - 10

16
35

Note: Pilot pressure should be at least 1 bar


higher than process fluid.

Main valve:
Brass - hot stamping or St.st
Seals:
NBR

Media:

Air, gas, water, fuel, oil etc

2W NO
Size

Mounting Bracket
A

Size

1/4"-3/8 58

36

1/4-3/8" BSP/NPT

1/4"

1/2" BSP/NPT

3/8", 1/2"

1/2"

69 47.5

15

25 4.5 11

14

20

25

32

20

30

22

25

33

40

13

3W NO
Size

1/4"

58

61

1/2"

69

77.5

1/4" BSP/NPT

1/8"BSP/NPT 25

1/8" BSP/NPT

1/8"BSP/NPT 30

32

M4 7

25

38

M5 9

30

Dimensions

2W NO

22

22

M5 DEEP 8
TYP x 2

3W NO

1/8 BSP
or NPT

1.74

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL External Pilot Operated


3/4", 1" 2/2 Way, NO
General Description
GEM-SOL 2/2 way, NO external pilot operated
valves are recommended for applications where
high flow at high pressure is required.
They can be used in control and automation
systems.
The typical applications are: industrial furnace,
heating equipment, burners, oil and gas, autoclaves,
dental equipment, instrumentation, car washers,
machine industries and irrigation.

Notes
Pilot

Pilot pressure should be at least 1 bar


higher than process fluid.
To order valves manufactured to your
specific requirements, please contact
our technical sales department.

Flow

How to Order
Example : GEM-E-2502N
Is a GEM-SOL external pilot operated
Brass, 3/4" BSP, 2W NO with NBR seals.

GEM-E

Body
Brass
St.st

Port
2
3

3/4" BSP
3/4"NPT
1" BSP
1" NPT

Function
50
51
60
61

2W NO

Seals
2

1.75

NBR
Viton
EPDM

N
V
E

GEM-SOL Index
Technical Specifications
Pressure and flow table

Functions:

2/2 Way NO

Ports size:

3/4", 1" BSP & NPT

Size

Orifice
(mm)

Pressure & flow:

See table

3/4"

20

Temperature range:

Fluid: max 80 C

1"

Ambient: -10 to 50 C

Kv(L/Min)
125

0.3 - 10

200

Note: Pilot pressure should be at least 1 bar


higher than process fluid.

Materials in contact
with fluid:

25

Pressure
(bar)

Main valve:
Brass - hot stamping
Stainless steel - AISI 316
Seals:
NBR, Viton, EPDM

Media:

Air, gas, water, fuel, oil etc

2W NO
Size

3/4"

90

59 3/4" BSP/NPT 1/8"BSP/NPT 55

17

1"

100 64

1" BSP/NPT 1/8"BSP/NPT 65

21

Dimensions

1.76

SV-04-09

GEM-SOL Index
BACCARA

GEM-SOL Digital Dual & Global


Timer Condensers

How to Order
Example : GEM-T-21-51
Is a GEM-SOL digital Dual timer condendser timer with
1/4" NPT port, 110V AC coil and connector.
T : Dual Timer
T1 : Global Timer

GEM-T
Port

GEM-T1

w/out valve
1/8"BSP
1/8"NPT
1/4"BSP
1/4"NPT
3/8"BSP
3/8"NPT
1/2"BSP
1/2"NPT
3/4"BSP
3/4"NPT

Voltage
00
10
11
20
21
30
31
40
41
50
51

No coil
24VAC
48VAC
110VAC
120VAC
230VAC
240VAC
other

Connector
0
3
4
5
6
7
8
9

without
with
with LED

1.77

0
1
2

Technical Info

GEM-SOL Index
Technical Specifications
Valve Specifications

See table

Voltage Supply:

24 to 240 VAC

Valve

50 or 60 Hz
Digital Dual Condenser Timer (T):
Time ranges:

Off 0 - 99.59 [min]


On 0 - 59 sec.

Digital Global Condenser Timer (T1):


Time ranges:

Off 0 - 24 hr

Valve size

GEM-SOL
Valve Type

Orifice

Kv(l/min)

1/8"

GEM-I

3.8

1/4"

GEM-I

3.8

3/8"

GEM-S

16

1/2"

GEM-S

12

35

3/4"

GEM-S

25

136

On 0 - 24 hr
Electric connection:

AMP pins, DIN 46242,

TIME ADJUSTMENT
Press SET for 2 seconds
Press ADJ to adjust ON time
Press SET
Press ADJ to adjust OFF-time seconds
Press SET
Press ADJ to adjust OFF-time minutes
Press SET

2 poles + 1 earth
Ambient temperature:

-10C to 50C

Weight:

64gr.

Protection class IP65 when installed


with a connector to coil.

DIGITAL DISPLAY
Count down ON and OFF times.
Manual override: Press keys for 2 secs.

Dimensions

1.78

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Proportional 2/2 Way NC


Direct Operated Valve
General Description
This valve is a 2/2 Way normally closed direct
operating solenoid valve and is based on the
GEM-SOL solenoid valve. It is used as a control
valve in process control, medical systems etc.

Working Principle
The Solenoid Operator is used to create a magnetic
force. The balance between this force and the
returning spring at any current, is used to control
the plunger stroke which determines the valve opening.
The magnetic force is direct associated to the current
passing in the coil.
The fluid enters the valve below the seat. The fluid
pressure together with the magnetic force acts against
the return spring. Setting this spring will change the
minimum current needed to open the valve, and by that,
the minimum flow.

Notes

IN

OUT

Flow

Because this is a specialized valve, we recommend


that you contact our engineering department in the
planning phase.

How to Order
Example : GEM-PR-21015N0-1
Is a GEM-SOL Proportional direct operating,
Brass, 1/8" BSP 2WNC, 2.4 orifice, NBR,
without manual override, with connector.
GEM-PR

Body
Brass
St.st
Alum.

Port
2
3
5

1/8"BSP
1/8"NPT
1/4"BSP
1/4"NPT

Function
10
11
20
21

2WNC

Input Control

Orifice
0.8
1.2
1.6
2.0
2.4
3.0
4.0

Manual
Override

Seals
1
2
3
4
5
6
7

NBR

Viton

EPDM

E
Polyurethane P
PTFE

1.79

None

Connector
without
with

0
1

GEM-SOL Index
Technical Specifications
Function:
Ports size:
Orifice:
(2)
Kv :
Pressure range:
Temperature range:
Materials in contact
with fluids

Weight (with coil):


Media:
Mounting:

2/2 Way NC
1/8" and 1/4" BSP & NPT
See table
See table
Vacuum to maximum pressure
~ see table
Fluid: -10C to 80C
Ambient: -10 C to 55 C
Main valve :
Aluminum, Brass,
Stainless steel 316
Solenoid Operator:
Stainless St. 300/400 series
Seals:
NBR, Viton, EPDM, Polyurethane,
PTFE
Guide Rings: PTFE
250 gr (aluminum base)
Neutral gases, water, oil
2
Max. Viscosity 21mm /s
In any position, preferably upright

Maximum Working Pressure (bar)


Orifice Size (mm)

0.8

1.2

1.6

2.0

2.4

3.0

4.0

Pressure rating [bar]

16

12

10

3.5

Kv (l/min)

0.6

1.1

1.7

2.5

3.5

4.5

(3)

Electrical Specification:
The Control Parameter is the current in the Coil!
Operating Current:
100-500 [mA]
Standard voltage 24 VDC(=)
Protection Class:
IP65 with connector
Coil terminal:
Per DIN 43650-a, or
2 flying leads 18AWG
300mm length.

Dimensions
Mounting Bracket

BRASS / St.St.

ALUMINUM

1.80

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Pilot Operated for Dust Collectors


3/4", 1", 1-1/2", 2" 2/2 Way
General Description
GEM-SOL Pilot Operated 2/2 way solenoid valves for
dust collectors have L-type form, high flow, fast opening,
to clean bag filters by applying a jet of air.
The modular concept of the valve allows many
combinations and variations to meet different requirements.
The design is compact with high flow rates,
long life and low maintenance.

Notes
A minimum differential pressure
of 0.3 bar is required for operation.
To order valves manufactured to
your specific requirements,
please contact our technical
sales department.

3/4", 1"

1-1/2", 2"

IN

IN

How to Order
Example : GEM-D-1501N0-311

GEM-D

Body
Al

Function

Port
5

3/4"BSP
3/4"NPT
1" BSP
1" NPT
1-1/2"BSP
1-1/2"NPT
2"BSP
2"NPT

50
51
60
61
70
71
80
81

2W NC

OUT

OUT

Is a GEM-SOL Pilot operated Al.


3/4"BSP, 2W NC, NBR seals,
without manual override, 24V AC 8W 50Hz
with connector.

Manual
Override

Seals
N

NBR

1.81

None

Voltage
W/out coil
6
12
24
48
110
120
230
240
other

0
1
2
3
4
5
6
7
8
9

Connector

Power
No coil
AC8W 50Hz
AC8W 60Hz
DC10W

0
1
2
3

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub
surge
protection
with LED
other

0
1
2
3
4
5
6
9

GEM-SOL Index
Technical Specifications
Valve specification NC Type

Function:

2/2 way NC

Ports size:

3/4", 1", 1-1/2", 2" BSP & NPT

Pressure and flow:

See table

Temperature range:

Fluid: -10C to 80C


Ambient: -15C to 50C

Materials in contact
with fluid :

Orifice Kv Pressure range Weight


(gf)
(mm) (L/Min)
AC/DC
*less coil

Port
Connection

Main valve :
Aluminium

3/4"

20

130

0.3-15

300

1"

25

200

0.5-15

330

1-1/2"

40

540

0.5-10

1230

2"

50

690

0.5-10

1860

* Coil weight approx. 110(gf), connector approx. 25 (gf)

Solenoid Operator:
Stainless steel 300 & 400 series
Seals:
Diaphragm: reinforced elastomer
NBR
Media:

Air

Coil voltage:

All Baccara coils voltages 10%


AC 8W

DC 10W

Protection class IP65 with connector

Dimensions

Size

Size

3/4"

73.5

55

123

31

36

46.2

3/4 BSP/NPT

1-1/2"

1"

82.2

65

126 28.25 40

46.2

1 BSP/NPT

2"

100 150.6

30

77

46.2 1-1/2" BSP/NPT

151.5 120 166.4

38

92

46.2

126

2 BSP/NPT

G TYPX2

B
E

G TYPX2
A

1.82

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL External Pilot Operated for Dust Collectors


3/4", 1", 1-1/2", 2" 2/2 Way
General Description
GEM-SOL External Pilot Operated 2/2 way solenoid valves for
dust collectors have L-type form, high flow, fast opening,
to clean bag filters by applying a jet of air.
The modular concept of the valve allows many
combinations and variations to meet different requirements.
The design is compact with high flow rates,
long life and low maintenance.

Notes
A minimum differential pressure
of 0.3 bar is required for operation.
To order valves manufactured to
your specific requirements,
please contact our technical
sales department.

IN

OUT

How to Order
Example : GEM-E-1501N
Is a GEM-SOL External Pilot operated Al.
3/4"BSP, 2W NC, NBR seals.

GEM-E

Body
Al

Port
5

3/4"BSP
3/4"NPT
1" BSP
1" NPT
1-1/2"BSP
1-1/2"NPT
2"BSP
2"NPT

Function
50
51
60
61
70
71
80
81

2W NC

Seals
N

NBR

1.83

GEM-SOL Index
Technical Specifications
Function:

2/2 way NC

Ports size:

3/4", 1", 1-1/2", 2" BSP & NPT

Pressure and flow:

See table

Temperature range:

Fluid: -10C to 80C

Valve specification NC Type


Weight
Orifice Kv
Port
Pressure range[bar] (gf)
Connection (mm) (L/Min)
*less coil

Ambient: -15C to 50C


Materials in contact
with fluid :

3/4"

20

130

0.3-15

300

1"

25

200

0.5-15

330

1-1/2"

40

540

0.5-10

1230

2"

50

690

0.5-10

1860

Main valve :
Aluminium
Solenoid Operator:
Stainless steel 300 & 400 series
Seals:
Diaphragm: reinforced elastomer
NBR

Media:

Air

Dimensions
Size

1-1/2"

126

30

77 1-1/2" BSP/NPT 79.3

151.5 120 114.9

38

92

2 BSP/NPT

95.1

2"

100 99.1

G TYPx2

E
A

1.84

SV-04-09

Technical Info

GEM-SOL Index
BACCARA

GEM-SOL Direct Operated Universal


1/8", 1/4"
General Description
GEM-SOL 3/2 way universal solenoid valves
are recommended for heavy duty
applications where high performance
is required. They can be used as NC, NO
selecting or diverting functions.
The valves are used in industrial and
irrigation control and automation systems.
These valves are suitable to work with
air, water and oil; please consult with us if you
need the valves to work with other fluids.

Notes
Valves are inspected at general pressures
of 12 bar or less (see table). Valves for
higher pressures are available.
ADC valves are suitable to work only with
AC 8W or DC 10W coils.
To use diverting function with DC, use
special order code.
Latch valves are available upon request.
To order valves manufactured to your
specific requirements, please contact our
technical sales department.

How to Order
Example : GEM-U-21095N-311

NC IN
Selector IN 1

OUT

Is a GEM-SOL direct operated Brass, 1/8"BSP,


universal function, 2.4 orifice, NBR,
24V AC 8W 50 Hz with connector.

EX NO
Diverting OUT 2

Diverting IN

2
NO IN
Selector IN 2

GEM-U

Body
Brass

Port
2

1/8" BSP
1/8" NPT
1/4" BSP
1/4" NPT

Function
10
11
20
21

divertor (1) 5
general
9
purpose

Orifice
1.6
2.0
2.4
3.0

3
4
5
6

(1) use only for DC

1.85

Voltage

Seals
NBR
Viton
EPDM

N
V
E

W/out coil
6
12
24
48
110
120
230
240
other

0
1
2
3
4
5
6
7
8
9

EX NC
Diverting OUT 1

Power
No coil
AC8W 50Hz
AC8W 60Hz
DC10W
AC5.5W 50Hz
AC5.5W 60Hz

Connector
0
1
2
3
4
5

without
with
with LED
with bi color
LED
flying leads
coil
with 1/2" Hub

0
1
2
3
4
5

GEM-SOL Index
Technical Specifications
Function:

Max.pressure (bar) 3W universal function table

3/2 way NC & NO

Coil
Current/Power

selecting & diverting

Orifice

1.6

2.0

2.4 3.0

AC/8W

14

6.5

Ports size:

1/8" and 1/4" BSP & NPT

Orifice:

See table

Kv:

See table

AC/5.5W

11

5.5

Pressure range:

See table

* DC 10W

10

5.5

Temperature range:

Fluid: max 80 C

Flow factor Kv(L/min)

1.7

2.5

Ambient: -10 C to 50 C

* not applicable for diverting function

Materials :

3.5 4.5

Main valve :
Brass

Max.pressure (bar) 3W diverting function table

Solenoid Operator:
Stainless steel 300 & 400 series

Coil
Current/Power

Orifice

1.6

2.0

2.4

3.0

Seals:

DC 10W

12

10

5.5

NBR, Viton, EPDM

Flow factor Kv(L/min) 1.7

2.5

3.5

4.5

Weight (with coil):

336 gr

Media:

Air, water, oil

Coil voltage:

All Baccara coils voltages

10%

AC 8W, 5.5W & DC 10W


Protection class IP65 with connector

Dimensions

82.3

46.5

44

38.5

1.86

1/8" or 1/4" BSP


TYP x 3

SV-04-09

Main Contents

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Coil
General Description
G80 coils are designed to withstand industrial
ambient conditions.
The coils are constructed according to
EN 60204.1 and used on G80 operators.

Notes
The coil should not be energized without
being mounted on operator.
The coils are designed to operate at 10%
of rated voltage.
The coils are suitable to operate at 100% duty
cycle, however when using high power coils for
a long time, the temperature developed may affect
solenoid seals. Viton seals or lower power coils
are advised.
For outdoor or high humidity application, please
consult our technical sales department.

How to Order

G80-B

Voltage

Power

Connector

Example : G80-B-331
6
12
24
110
230

Is a G80 Coil 24V DC 6.5W with connector.


Available variations coils table

AC

DC

50 Hz 60 Hz
V 7.5 4
6
12
24
110
230

3 6.5 3

Please contact our technical sales


department for specific requirements.

2.1

1
2
3
5
7

AC7.5W 50Hz
AC6W 60Hz
DC 6.5W
AC4W 50Hz
AC3W 60Hz
DC 3W

1
2
3
4
5
7

without
with
with bi
color LED
with LED and
surge
protection
flying leads
coil
other

0
1
2
3
4
9

GEVA-80 Index
Technical Specifications
Electrical specifications
Standard voltages:

24, 110, 230V AC (50 or 60 Hz): 6, 12, 24 DC

Variation in voltage:

Over voltage category II 10% Nominal voltage

Duty cycle:

100%

Ambient temperature:

-20 C to 70 C

Isolation class:

F 155

Protection grade:

IP65 (with connector) - dust and splash proof

Coil terminal:

AMP 6.3x0.8 DIN 43650, 2 poles + 1 earth

Connector:

DIN 43650, fixture: M3 screws, 2 positions at 180

Assembly:

On a valve, 4 positions at 90

Fixing:

On a G80 operator with M8x0.75 nut

Weight:

Approx 51gr.

Power Ratings
High
50Hz

60Hz

Inrush power (VA)

12.5

Holding (VA)

8.8

Rated powerDC (W)

Low
DC

50Hz

60Hz

10.5

7.5

6.5

4.2

DC

6.5

Dimensions

16
+0.05
0

6.4 0.1

23.1

29.5

1.5

8.15

22

9.15 0.05

18

11

37

2.2

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Wide Coil


General Description
G80 wide coils are designed to withstand
industrial ambient conditions.
The coils are constructed according to
EN 60204.1 and used on G80 operators.

Notes
The coil should not be energized without
being mounted on operator.
The coils are designed to operate at 10%
of rated voltage.
The coils are suitable to operate at 100% duty
cycle, however when using high power coils for
a long time, the temperature developed may affect
solenoid seals. Viton seals or lower power coils
are advised.
For outdoor or high humidity application, please
consult our technical sales department.

How to Order

G80-BW

Voltage

Power

Connector

Example : G80-BW-331
6
12
24
110
230

Is a G80 wide coil 24V DC 4.5W


with connector.

2.3

1
2
3
5
7

AC5W 50Hz
AC4W 60Hz
DC 4.5W
AC3W 50Hz
AC2W 60Hz
DC 2.5W

1
2
3
4
5
7

without
with
with bi
color LED
with LED and
surge
protection
other

0
1
2
3

GEVA-80 Index
Technical Specifications
Electrical specifications
Standard voltages:

24, 110, 230V AC (50 or 60 Hz): 6, 12, 24 DC

Variation in voltage:

Over voltage category II 10% Nominal voltage

Duty cycle:

100%

Coil temperature:

-20 C to 70 C ambient

Isolation class:

F 155

Protection grade:

IP65 (with connector) - dust and splash proof

Coil terminal:

AMP 6.3x0.8 DIN 4624.2, 2 poles + 1 earth

Connector:

DIN 46242, fixture: M3 screws, 2 positions at 180

Assembly:

On a valve, 4 positions at 90

Fixing:

On a G80 operator with M8x0.75 nut

Power Ratings
High
50Hz

60Hz

Inrush power (VA)

Holding (VA)

Low
DC

50Hz

60Hz

7.5

5.5

4.5

4.2

2.5

Rated power DC (W)

4.5

DC

2.5

Dimensions

15

30

0.8 0.03

18.8 0.1

6 0.1
0
9 -0.4

29.5

16

8
9
+0.4
12 -0.2

22

14

48

2.4

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Operator
General Description
The operator is designed to be assembled on a valve
or a counterpart to set up a solenoid valve.
According to the operator and valve construction,
various functions are available.
The G80 operators may be used with alternate or
direct current.

Notes
Operator cavity should be designed according
to our specifications, see drawing on the next
page.
Operator for DC is without shading ring and
may not be used for AC.
When assembling coil, take care not to tighten
nut excessively.
Valves are inspected at general pressure of up
to 10 bar. Higher pressures are available, please
consult our technical sales department.
For applications where abnormal conditions exist
and for fluids other than air, water or inert gases,
please consult our technical sales department.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

2W NOa
thru base

How to Order

3W NOa
thru base

3W

2W

Example : G80-O-2W210-N-341
Is a GEVA 80 Operator, Brass tube, 2W NC, DC,
NBR, 24V DC 6.5W with connector.

Example : G80-O-002302-N-341
Is a GEVA 80 Operator, M5, Brass tube, 3W NC, DC,
1.2 orifice, NBR seals, 24V DC 6.5W with connector

2W
G80-O

2W

Tube
Brass
St.st

3W
G80-O

Port

Function
2
3

Tube

00 Brass
M5
#10UNF
01 St.st
1/8 BSP(2) 10

2W NC
2WNOa

1
2a

Function
2
3

Current
DC
AC

0
1

Current

3 DC
3W NC
4 AC
3W NO
3W NOa 4a

0
1

Voltage

Seals
NBR
Viton
EPDM
Kalrez(1)

Orifice
None(2W)
1
1.2
1.6

2.5

0
1
2
3

N
V
E
K

W/out coil
6
12
24
110
230

0
1
2
3
5
7

Power
No coil
AC7.5W 50Hz
AC 6W 60Hz
DC 6.5W
AC 4W 50Hz
AC 3W 60Hz
DC 3W

Connector
0
1
2
3
4
5
7

(1) Kalrez O-ring is available only upon request.


When ordering Kalrez seals, please consult
with our technical sales department about
O-ring compound.
Available only in 2W NC.
(2) Option available with use of an adaptor.

without
with
with bi color
LED
with LED and
surge
protection
other

0
1
2
3
9

GEVA-80 Index
Technical Specifications
Threads on
operator tube:

Function:

2/2, 3/2 Way NC or NO

Orifice size:

1, 1.2, 1.6mm

Pressure range(bars):

Standard up to 10

female to connect exhaust,

Flow factor Kv(l/min):

See solenoid valve performances

muffler etc.

Temperature range:

Fluid: max 80 C

Operator assembly:

M8x0.75 male - M5 or #10UNF

Insert operator into

Ambient: -10 C to 50 C

cavity. Fix the coil with

Response time:

5 - 12 msec

one M8 nut.

Cycling rate:

2000 cycles per minute

Materials in contact
with fluid :

Coil data:

See technical coil data

Standard voltage:

See "coil"

Operator :
Brass or Stainless steel
series AISI 300 & 400
Shading ring:
copper
Orifice:
Stainless steel

Weight:

18 gr (without coil)

Media:

Air, inert gases and water

Dimensions
Operator seating

2.6

SV-01-10

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Operator M12


General Description
The operator is designed to be assembled on a valve
or a counterpart to set up a solenoid valve.
According to the operator and valve construction,
various functions are available.
The G80 operators may be used with alternate or
direct current.

Notes
Operator cavity should be designed according
to our specifications, see drawing on the next
page.
Operator for DC is without shading ring and
may not be used for AC.
When assembling coil, take care not to tighten
nut excessively.
Valves are inspected at general pressure of up
to 10 bar. Higher pressures are available, please
consult our technical sales department.
For applications where abnormal conditions exist
and for fluids other than air, water or inert gases,
please consult our technical sales department.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

2W

3W

How to Order
Example : G80-OM-2W210-N-331
Is a GEVA 80 operator M12, Brass tube, 2WNC, DC,
NBR seals, 24V DC 6.5W with connector

2W NOa

Example : G80-OM-002302-N-331

3W NOa

Is a GEVA 80 operator M12, M5, Brass tube, 3WNC, DC,


1.2 orifice, NBR seals, 24V DC 6.5W with connector

2W
G80-OM

2W

Tube
Brass
St.st

Function
2
3

2W NC
2W NO

1
2a

Current
DC
AC

NBR
Viton
EPDM
Teflon
Kalrez(1)

0
1

3W
G80-OM

Voltage

Seals
N
V
E
T
K

(1) 2W NC only

Port
None (2W) 00
M5
#10UNF 01

Tube
Brass
St.st

Function
2
3

3W NC
3W NO
3W NO

3
4
4a

Current
DC
AC

Orifice

0
1

1
1.2
1.6

2.7

1
2
3

W/out coil
6
12
24
110
230

0
1
2
3
5
7

Power
No coil
0
AC7.5W 50Hz 1
AC6W 60Hz 2
DC 6.5W
3
AC 4W 50Hz 4
AC 3W 60Hz 5
DC 3W
7

Connector
without
with
with bi color
LED
with LED
and surge
protection
flying leads
coil
other

0
1
2
3
4
9

GEVA-80 Index
Technical Specifications
Function:

2/2, 3/2 Way NC or NO

Threads on

Orifice size:

1, 1.2, 1.6mm

operator tube:

Pressure range(bars):

Standard up to 10

female to connect exhaust,

Flow factor Kv(l/min):

See solenoid valve performances

muffler etc.

Temperature range:

Fluid: Max. 80C

Operator assembly:

M8x0.75 male - M5 or #10UNF

Insert operator into

Ambient: -10C to 50C

cavity. Fix the coil with

Response time:

5 - 12 msec

one M8 nut.

Cycling rate:

2000 cycles per minute

Materials in contact
with fluid :

Coil data:

See technical coil data

Standard voltage:

See "coil"

Operator :
Brass or Stainless steel
series AISI 300 & 400
Shading ring:
copper
Orifice:
Stainless steel

Weight:

18 gr (without coil)

Media:

Air, inert gases and water

Dimensions
Operator seating

Spring

2.8

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Operator 3/4" UNEF


General Description
The operator is designed to be assembled on a valve
or a counterpart to set up a solenoid valve.
According to the operator and valve construction,
various functions are available.
The G80 operators may be used with alternate or
direct current.

Notes
Operator cavity should be designed according
to our specifications, see drawing on the next
page.
Operator for DC is without shading ring and
may not be used for AC.
When assembling coil, take care not to tighten
nut excessively.
Valves are inspected at general pressure of up
to 10 bar. Higher pressures are available, please
consult our technical sales department.
For applications where abnormal conditions exist
and for fluids other than air, water or inert gases,
please consult our technical sales department.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.
2W

How to Order

3W

Example : G80-OU-2W210-N-331
Is a GEVA 80 3/4" UNEF operator, Brass tube,
2WNC, DC, NBR seals, 24V DC 6.5W with connector.

Example : G80-OU-003302-N-331
Is a GEVA 80 3/4" UNEF operator, M5 port, St.st tube,
3WNC, DC,1.2 orifice, NBR seals, 24V DC 6.5W with connector.

2W
G80-OU

2W

Tube
Brass
St.st

2
3

Function
2W NC
2W NO

1
2a

Current
DC
AC

0
1

NBR
Viton
EPDM

3W
G80-OU

Port
M5
#10UNF

Tube
00 Brass
01 St.st

2
3

Function
3W NC
3W NO
3W NO
through
base

3
4
4a

Current
DC
AC

0
1

Voltage

Seals

Orifice
1
1.2
1.6

2.9

1
2
3

N
V
E

W/out coil
6
12
24
110
230

0
1
2
3
5
7

Power
No coil
AC7.5W 50Hz
AC 6W 60Hz
DC 6.5W
AC 4W 50Hz
AC 3W 60Hz
DC 3W

Connector
0
1
2
3
4
5
7

without
with
with bi color
LED
with LED
and surge
protection
other

0
1
2
3

GEVA-80 Index
Technical Specifications
Function:

2/2, 3/2 Way NC or NO

Threads on

Orifice size:

1, 1.2, 1.6mm

operator tube:

Pressure range(bars):

Standard up to 10

female to connect exhaust,

Flow factor Kv(l/min):

See solenoid valve performances

muffler etc.

Temperature range:

Fluid: Max 80 C

Coil data:

See technical coil data

Ambient: -10 C to 50 C

Standard voltage:

See "coil"

Response time:

5 - 12 msec

Cycling rate:

2000 cycles per minute

M8x0.75 male - M5 or #10UNF

Materials in contact
with fluid :

Operator :
Brass or Stainless steel
series AISI 300 & 400
Shading ring:
copper
Orifice:
Stainless steel

Weight:

18 gr (without coil)

Media:

Air, inert gases and water

Dimensions

Operator seating

2.10

SV-01-10

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Latch Operator 2W, 3W


General Description
The operator is designed to be assembled on a valve
or a counterpart to set up a solenoid valve.
According to the operator and valve construction,
various functions are available.
The G80 Latch operators may be used with direct current.

Notes
Operator cavity should be designed according
to our specifications, see drawing on the
previous page.
These operators are compatible with all G80 valves
at 12 and 24V DC. Use "L" as the power indicator.
When assembling coil, take care not to tighten
nut excessively.
Valves are inspected at general pressure of up
to 10 bar. Higher pressures are available, please
consult our technical sales department.
For applications where abnormal conditions exist
and for fluids other than air, water or inert gases,
please consult our technical sales department.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

How to Order
Example : G80-OL-002302N-3L1
Is a GEVA 80 latch operator, M5 port, Brass tube, 3WNC, 1.2 orif
24V DC Latch with connector

G80-OL

Type

Port

"O"ring Nil
type
M12
M
3/4 UNEF U

00
M5
#10UNF 01
1/8"BSP 10

Tube
Brass
St.st

2
3

Function

Orifice

1
3
4

None(2W)
1
1.2
1.6

2W NC
3W NC
3W NO

2.11

Voltage

Seals
0
1
2
3

NBR
Viton
EPDM

N
V
E

W/out coil
6
12
24

0
1
2
3

Power
No coil
Latch

Connector
0
L

without
with

0
1

GEVA-80 Index
Technical Specifications
Function:

2/2, 3/2 Way NC or NO

Threads on

Orifice size:

1, 1.2, 1.6mm

operator tube:

Pressure range(bars):

Standard up to 10

Flow factor Kv(l/min):

See solenoid valve performances

Temperature range:

Fluid: Max 80 C

M8x0.75 male - M5 or #10UNF


female to connect exhaust,
muffler etc.

Operator assembly:

Insert operator into cavity,

Ambient: -10 C to 50 C

tighten it by the flange and

Materials in contact
with fluid :

the two M3 screws. Fix the


Operator :

coil with one M8 nut.

Brass or Stainless steel


series AISI 300 & 400
Orifice:

Coil data:

See technical coil data

Standard voltage:

See "coil"

Operation:

See engineering &

Stainless steel
Weight:

18 gr (without coil)

Media:

Air, inert gases and water

technical information
section.

38.9

29.5

Dimensions

22

17

28

2.12

SV-01-10

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Direct Operated


2/2 Way NC, NO
General Description
These valves are based on the GEVA 80 operator
with 8mm diameter plunger. Due to its relatively low
power consumption, the valve can be directly operated
from an electronic controller.
The valves are used mainly in pneumatic applications
as a pilot valve, but can be used for gas, water and
light oils.

Notes
Valves are 100% inspected at 10 bar. Valves for
higher pressure are available upon special request.
See table for maximum pressures.
Valves for pressure higher than 12 bar are less
manual override.
The valves are AC or DC designated.
The coil can be mounted in 4 positions, at 90 apart.
The coil plug can rotate 2 positions at 180.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

2
1
NC

G80-A

Body (1)
Al
Brass
St.st

1
2
3

Port
M5
#10UNF
1/8"BSP
1/8"NPT

Function
00
01
10
11

2W NC
2WNO

1
2

Orifice
1
1.2
1.6
2(2)
2.4(2)
3.0(2)

1
2
3
4
5
6

Manual
override

Seals
NBR
Viton
EPDM
Kalrez(3)

(1) For St.st tube, add "s".


(2) NC only
(3) Kalrez O-ring is available only upon request.
When ordering Kalrez seals, please consult
with our technical sales department about
O-ring compound.

2.13

N
V
E
K

None
plastic

0
1

NO

Voltage
W/out coil
6
12
24
110
230
other

0
1
2
3
5
7
9

Power
No coil
0
AC7.5W50Hz 1
AC6W60Hz 2
DC6.5W
3
AC4W50Hz 4
AC3W60Hz 5
DC3W
7

Connector
without
with
with bi
color LED
with LED
& surge
protection
other

0
1
2
3
9

GEVA-80 Index
Technical Specifications
Max. Pressure (Bar) 2W NC Table

Function:

2/2 Way NC or NO

Port size:

G1/8" BSP or NPT,#10UNF, M5

Pressure and flow:


Media:
Temperature range:

Pressure rating according to both

Coil
Current/Power

Orifice (mm)
1

1.2

1.6

2.4

3.0

orifice size and power rating

AC - 7.5W

40

35

35

12

10

Fluid and gases with viscosity less

AC - 4W

40

30

15

than 3 E

DC - 6.5W

40

35

20

12

10

DC - 3W

40

30

15

2.5

0.5

0.65

1.2

1.6

Fluid: -10 C to 80 C (with no


freezing)

Flow factor Kv(L/min)

Ambient: -10 C to 50 C
Materials (in contact
with media) :

Max. Pressure (Bar) 2W NO Table

Tube :
Brass or AISI 303 for St.st valves
Plunger & upper pole:

Coil
Current/Power

Orifice (mm)
1.2 1.6

430 FR

AC - 4W

15

10

Seals:

DC - 3W

15

10

0.4

0.7

NBR, Viton, EPDM, Kalrez

Flow factor Kv(L/min)

Base:
Al-6061, AISI 303 or Brass
Responded time:

5 - 12msec

Weight:

50 gr (aluminium valve)

Electrical specifications
Standard voltages:

24, 110, 230V AC

Duty cycle:

100%

6, 12, 24V DC

Variation in voltage:

10% nominal voltage


Protection class IP65 with connector

Dimensions
2X M3 DEEP 6

2.14

Port

M5/10 UNF

5.5

51.5

1/8"

10

58.5

SV-04-09

GEVA-80 Index

Technical Info

GEVA 80 Direct Operated


2/2 Way NC, NO

(1)

(1) For St.st tube, add "s".


other

2.15

GEVA-80 Index

Flow factor Kv(L/min) 0.65

1.2

1.6

Max. Pressure (Bar) 2W NO Table

Flow factor Kv(L/min)

0.4

0.7

PA 6.6

2.16

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Compact Direct Operated


2/2 Way NC
General Description
These valves are based on the GEVA 80 operator with 8mm
diameter plunger. Due to its relatively low power consumption
the valve can be directly operated from an electronic controller
The valves are used mainly in pneumatic applications as a
pilot valve but can be used for gas, water and light oils.

Notes
Valves are 100% inspected at 10 bar. Valves for higher
pressure are available upon special request. See table for
maximum pressures.
The valves are AC or DC designated.
The coil plug can rotate 2 positions at 180 .
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

Inline

Angle

How to Order
Flow

Example : G80-A-A1011V-020

Flow

Is a GEVA 80 Compact direct operated valve,


angle type base, 1/8" BSP, 2WNC, 1mm orifice,
Viton seals, without coil, AC 6W 60Hz and without connector.

G80-A

Body(1)
Inline
Angle

G
A

Function

Port
1/8" BSP
1/8" NPT
1/4" BSP
1/4" NPT

10
11
20
21

2W NC

Orifice
1
1.2
1.6
2
2.4

Seals
1
2
3
4
5

NBR
Viton
EPDM

(1) For St.st tube add "s"

2.17

Voltage
N
V
E

W/out coil
6
12
24
110
230
other

0
1
2
3
5
7
9

Power
0
No coil
AC7.5W50Hz 1
AC6W60Hz 2
3
DC6.5W
AC4W50Hz 4
AC3W60Hz 5
7
DC3W

Connector
without
with
with bi-color
LED
with LED
and surge
protection
other

0
1
2
3
9

GEVA-80 Index
Technical Specifications
Function:

2/2 Way NC

Port size:

G1/8" BSP or NPT

Pressure and flow:

Pressure rating according to both

Media:

Max. Pressure (Bar)

2W NC Table

Coil
Current/Power

Orifice (mm)
1.2
1.6
2

2.4

orifice size and power rating

AC - 7.5W

40

35

35

12

10

(see electrical specifications)

AC - 4W

40

30

15

DC - 6.5W

40

35

20

12

10

DC - 3W

40

30

15

0.5

0.65

1.2

1.6

Fluid and gases with viscosity less


than 3 E

Temperature range:

Fluid: -10 C to 80 C (with no

Flow factor Kv(L/min)

freezing)
Ambient: -10 C to 50 C
Materials (in contact
with media) :

Tube :
Brass
Plunger & upper pole:
430 FR
Seals:
NBR, Viton, EPDM

Responded time:

5 - 12(msec)

Weight:

52gr.

Electrical specifications
Standard voltages:

24, 110, 230V AC 6, 12, 24V DC

Duty cycle:

100%

Variation in voltage:

10% nominal voltage


Protection class IP65 with connector

Dimensions

24

2.18

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Direct Operated Type HF (CNOMO)


2/2 Way NC, NO
General Description
Geva 80 (CNOMO) solenoid valves are designed to be
mounted on a sub-base or on an appropriate counterpart
adapted to this valve type.
This unit is suitable for use as a pilot for air valves. Also
this version is suitable for mounting any number of
valves on the same sub-base plate.
This system allows a wide program of control or automation
in minimum space and maximum rationalization.

Notes
Valves are 100% inspected at 10 bar. Valves
for higher pressure are available upon special request.
See table for maximum pressures.
Valves for pressure higher than 12 bar are less
manual override.
The valves are AC or DC designated.
The coil can be mounted in 4 positions at 90 apart.
The coil plug can rotate 2 positions at 180.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

How to Order
Example : G80-H-1s12N1-331
Is a GEVA 80 direct operated HF valve, aluminium base
with St.st tube, 2WNC, 1.2mm orifice, NBR seals,
with manual override, 24V DC 6.5W, with connector.

G80-H

Body (1)
Al.

Function
2W NC

Orifice
1
1.2
1.6

Manual
Override

Seals
1
2
3

NBR
Viton
EPDM

N
V
E

None
with

G80-HW
(1) For St.st tube add "s"

2.19

0
1

Voltage
W/out coil
6
12
24
110
230
other

0
1
2
3
5
7
9

Power

Connector

No coil
0
AC7.5W50Hz 1
AC6W60Hz 2
DC6.5W
3
AC4W50Hz 4
AC3W60Hz 5
DC3W
7

without
0
with
1
with bi-color 2
LED
3
with LED
and surge
protection
9
other

GEVA-80 Index
Technical Specifications
Function:

2/2 Way NC

Pressure and flow:

Pressure rating according to both

Max. Pressure (Bar) 2W NC Table


Coil
Current/Power

Orifice
1.0

1.2

1.6

(see electrical specifications)

AC - 7.5W

40

35

35

Media:

Air

AC - 4W

40

30

15

Temperature range:

Fluid: -10 C to 80 C (with no

DC - 6.5W

42

35

20

DC - 3W

40

30

15

0.5

0.65

1.2

orifice size and power rating

freezing)
Ambient: -10 C to 50 C

Flow factor Kv(L/min)

Materials (in contact


with media) :

Tube :
Brass or AISI 303 for St.st valves
Plunger & upper pole:
430 FR
Seals:
NBR, Viton, EPDM
Base:
AI-6061, AISI 303 or Brass

Responded time:

5 - 12(msec)

Weight:

50gr.

Electrical specifications
Standard voltages:

24, 110, 230V AC 6, 12, 24V DC

Duty cycle:

100%

Variation in voltage:

10% nominal voltage


Protection class IP65 with connector

Dimensions
W

G80 - H

20

70

56.5

G80 - HW

25

75

61.5

Valve

2.20

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Direct Operated


3/2 Way NC, NO
General Description
These valves are based on the GEVA 80 operator
with 8mm diameter plunger. Due to its relatively low
power consumption, the valve can be directly operated
from an electronic controller.
The valves are used mainly in pneumatic applications as
a pilot valve, but can be used for gas, water and
light oils.

Notes
Valves are 100% inspected at 10 bar. Valves for
higher pressure are available upon special request.
See table for maximum pressures.
Valves for pressure higher than 12 bar are less
manual override.
The valves are AC or DC designated.
The coil can be mounted in 4 positions at
90 apart.
The coil plug can rotate 2 positions at 180.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.
When ordering a latch valve please contact
our technical sales department.
1/8" adaptor available.

NC Ex

NO In

NC Out
NO

Ex NO
In NC

How to Order
Example : G80-A-11032V1-331
Is a GEVA 80 direct operated valve, aluminium base,
1/8"BSP, 3W NC, 1.2mm orifice with Viton seals,
plastic manual override, 24V DC 6.5W with connector.

G80-A

Body(1)

Port

1
2
3

M5
10UNF
1/8"BSP
1/8"NPT

Alum.
Brass
St.st

Function
00
01
10
11

3W NC
3WNO

3
4

Orifice
1
1.2
1.6

Manual
override

Seals
1
2
3

NBR
Viton
EPDM

(1) For St.st tube add "s"

2.21

N
V
E

None
plastic

0
1

Voltage
W/out coil
6
12
24
110
230
other

0
1
2
3
5
7
9

Power
No coil
AC7.5W50Hz
AC6W60Hz
DC6.5W
AC4W50Hz
AC3W60Hz
DC3W
Latch

Connector
0
1
2
3
4
5
7
L

without
with
with bi
color LED
with LED
& surge
protection
other

0
1
2
3

GEVA-80 Index
Technical Specifications
Function:

3/2 Way NC or NO

Port size:

G1/8" BSP or NPT, M5, #10UNF

Pressure and flow:

Media:

Max. Pressure (Bar)


Coil
Current/Power

Pressure rating according to both

Orifice (mm)
1.2
1.6

orifice size and power rating

AC - 7.5W

15

12

10.5

(see electrical specifications)

AC - 4W

12

10

Fluid and gases with viscosity less

DC - 6.5W

15

12

10.5

DC - 3W

12

10

0.5

0.65

than 3 E
Temperature range:

3W NC Table

Fluid: -10 C to 80 C (with no

Flow factor Kv(L/min)

freezing)
Ambient: -10 C to 50 C
Materials (in contact
with media) :

Max. Pressure (Bar)

Tube :

3W NO Table

Brass or AISI 303 for St.st valves

Coil
Current/Power

Plunger & upper pole:

AC - 7.5W

12

430 FR

AC - 4W

10

DC - 6.5W

12

DC - 3W

10

0.4

0.7

Seals:
NBR, Viton, EPDM
Base:

Flow factor Kv(L/min)

Al-6061, AISI 303 or Brass


Responded time:

5 - 12msec

Weight:

50gr. (aluminium valve)

Orifice (mm)
1.2
1.6

Electrical specifications
Standard voltages:

24, 110, 230V AC 6, 12, 24V DC

Duty cycle:

100%

Variation in voltage:

10% nominal voltage


Protection class IP65 with connector

Dimensions
2X M3 DEEP 6

M5/10 UNF

5.5

51.5

1/8"

10

58.5

PORT

2.22

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Direct Operated


3/2 Way NC, NO
General Description
These valves are based on the GEVA 80 operator
with 8mm diameter plunger. Due to its relatively low
power consumption, the valve can be directly operated
from an electronic controller.
The valves are mainly in pneumatic applications as
a pilot valve, but can be used for gas, water and
light oils.

Notes
Valves are 100% inspected at 10 bar. Valves for
higher pressure are available upon special request.
See table for maximum pressures.
Valves for pressure higher than 12 bar are less
manual override.
The valves are AC or DC designated.
The coil plug can rotate 2 positions at 180.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.
When ordering a latch valve please contact
our technical sales department.

NC EX

NO IN
3

NO EX

How to Order

NC/NO
OUT

Example : G80-A-41032V0-020

NC IN

Is a GEVA 80 direct operated valve, plastic base,


1/8" BSP, 3W NC, 1.2mm orifice with Viton seals,
without manual override without coil, AC 6W 60Hz and
without connector.

G80-A

Body (1)
Plastic

Port
1/8"BSP 10
1/8"NPT 11

Function
3W NC
3WNO

3
4

Orifice
1.2
1.6

2
3

Manual
override

Seals
NBR
Viton
EPDM

(1) For St.st tube add "s"

2.23

N
V
E

None
plastic

0
1

Voltage
W/out coil
6
12
24
110
230
other

0
1
2
3
5
7
9

Power
0
No coil
AC7.5W50Hz1
AC6W60Hz 2
3
DC6.5W
AC4W50Hz 4
AC3W60Hz 5
7
DC3W
L
Latch

Connector
without
with
with bi
color LED
with LED
& surge
protection
flying leads
coil
other

0
1
2
3
4
9

GEVA-80 Index
Technical Specifications
3/2 Way NC or NO

Max. Pressure (Bar)

Port size:

G1/8" BSP or NPT

Pressure and flow:

Pressure rating according to both

Coil
Current/Power

Function:

Media:

Orifice (mm)
1.2
1.6
1

orifice size and power rating

AC - 7.5W

15

12

10.5

(see electrical specifications)

AC - 4W

12

10

DC - 6.5W

15

12

10.5

DC - 3W

12

10

LATCH

15

12

10.5

0.65

Fluid and gases with viscosity less


than 3 E

Temperature range:

3W NC Table

Fluid: -10 C to 80 C (with no


freezing)
Ambient: -10 C to 50 C

Flow factor Kv(L/min) 0.5

Tube :

Max. Pressure (Bar)

Materials (in contact


with media) :

Brass or AISI 303

Coil
Current/Power

Plunger & upper pole:

Orifice (mm)
1.2
1.6

430 FR

AC - 7.5W

12

Seals:

AC - 4W

10

DC - 6.5W

12

DC - 3W

10

Flow factor Kv(L/min)

0.4

0.7

NBR, Viton, EPDM


Base:
NY 66
Responded time:

3W NO Table

5 - 12msec

Electrical specifications
Standard voltages:

24, 110, 230V AC 6, 12, 24V DC and Latch

Duty cycle:

100%

Variation in voltage:

10% nominal voltage


Protection class IP65 with connector

Dimensions

Manual
Override

2.24

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Compact Direct Operated


3/2 Way NC, NO

General Description
These valves are based on the GEVA 80 operator with 8mm
diameter plunger. Due to its relatively low power consumption
the valve can be directly operated from an electronic controller
The valves are mainly in pneumatic applications as a pilot valve
but can be used for gas, water and light oils.

Notes
Valves are 100% inspected at 10 bar. Valves for higher
pressure are available upon special request.
Angle
See table for maximum pressures.
NC EX
NO IN
The valves are AC or DC designated.
The coil plug can rotate 2 positions at 180.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.
Options:
Adaptor
Aluminium coil nut

Inline
NC EX

NO IN

NC IN
NC/NO
OUT

How to Order

NC IN

NC/NO
OUT
NO EX

NO EX

Example : G80-A-A1031V-020
Is a GEVA 80 Compact direct operated valve,
angle type base, 1/8" BSP, 3WNC, 1mm orifice,
Viton seals, without coil, AC 6W 60Hz and without connector.

G80-A

Body(1)
Inline
Angle

G
A

Port(2)
1/8" BSP
1/8" NPT
1/4" BSP
1/4" NPT

10
11
20
21

Function
3W NC
3W NO

3
4

Orifice
1
1.2
1.6

1
2
3

Voltage

Seals
NBR
Viton
EPDM

(1) For St.st tube add "s"


(2) 1/4" ports on base only

2.25

N
V
E

W/out coil
6
12
24
110
230
other

0
1
2
3
5
7
9

Power
0
No coil
AC7.5W50Hz 1
AC6W60Hz 2
3
DC6.5W
AC4W50Hz 4
AC3W60Hz 5
7
DC3W

Connector
without
with
with bi-color
LED
with LED
and surge
protection
flying leads
coil
other

0
1
2
3

4
9

GEVA-80 Index
Technical Specifications
Function:

3/2 Way NC, NO

Port size:

G1/8" BSP or NPT, M5, #10UNF

Pressure and flow:

Media:

Max. Pressure (Bar) 3W NC Table


Coil
Current/Power

Pressure rating according to both

1.2

1.6

orifice size and power rating

AC - 7.5W

15

12

10.5

(see electrical specifications)

AC - 4W

12

10

Fluid and gases with viscosity less

DC - 6.5W

15

12

10.5

DC - 3W

12

10

0.5

0.65

than 3 E
Temperature range:

Orifice (mm)
1

Fluid: -10 C to 80 C (with no

Flow factor Kv(L/min)

freezing)
Ambient: -10 C to 50 C

Max. Pressure (Bar) 3W NO Table

Materials (in contact


with media) :

Coil
Current/Power

Tube :
Brass

Orifice (mm)
1.2
1.6

AC - 7.5W

12

430 FR

AC - 4W

10

Seals :

DC - 6.5W

12

NBR, Viton, EPDM, Kalrez

DC - 3W

10

0.4

0.7

Plunger & upper pole :

Responded time:

5 - 12(msec)

Weight:

52gr.

Flow factor Kv(L/min)

Electrical specifications
Standard voltages:

24, 110, 230V AC 6, 12, 24V DC

Duty cycle:

100%

Variation in voltage:

10% nominal voltage


Protection class IP65 with connector

Dimensions
or #10UNF

22

or #10UNF

2.26

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Direct Operated Type HF (CNOMO)


3/2 Way NC
General Description
Geva 80 (CNOMO) solenoid valves are designed to be
mounted on a sub-base or on an appropriate counterpart
adapted to this valve type.
This unit is suitable for use as a pilot for air valves. Also
this version is suitable for mounting any number of valves
on the same sub-base plate.
This system allows a wide program of control or automation
in minimum space and maximum rationalization.

Notes
Valves are 100% inspected at 10 bar. Valves
for higher pressure are available upon special request.
See table for maximum pressures.
Valves for pressure higher than 12 bar are less
manual override.
The valves are AC or DC designated.
The coil can be mounted in 4 positions at 90 apart.
The coil plug can rotate 2 positions at 180.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.
Options:
Adaptor
Aluminium coil nut

How to Order
Example : G80-H-132N1-331
Is a GEVA 80 direct operated HF valve,
3WNC, 1.2mm orifice, NBR seals, with manual
override, 24V DC 6.5W, with connector.
Body (1)

G80-H
Al.

G80-HW

Function

Orifice

3W NC

1.2
1.6

2
3

Manual
Override

Seals
NBR
Viton
EPDM
Kalrez

N
V
E
K

None
with

(1) For St.st tube add "s"

2.27

0
1

Voltage
W/out coil
6
12
24
110
230
other

0
1
2
3
5
7
9

Power
No coil
AC7.5W50Hz
AC6W60Hz
DC6.5W
AC4W50Hz
AC3W60Hz
DC3W

Connector
0
1
2
3
4
5
7

without
with
with bi-color
LED
with LED
and surge
protection
other

0
1
2
3

GEVA-80 Index
Technical Specifications
Max. Pressure (Bar) 3W NC Table

Function:

3/2 Way NC

Pressure and flow:

Pressure rating according to both

Coil
Current/Power

Orifice
1.2

1.6

(see electrical specifications)

AC - 7.5W

12

10.5

Media:

Air

AC - 4W

10

Temperature range:

Fluid: -10 C to 80 C (with no

DC - 6.5W

12

10.5

DC - 3W

10

orifice size and power rating

freezing)
Ambient: -10 C to 50 C

Flow factor Kv(L/min) 0.65

Materials (in contact


with media) :

Tube :
Brass or AISI 303 for St.st valves
Plunger & upper pole:
430 FR
Seals:
NBR, Viton, EPDM, Kalrez
Base:
AI-6061, AISI 303 or Brass

Responded time:

5 - 12(msec)

Weight:

50gr.

Electrical specifications
Standard voltages:

24, 110, 230V AC 6, 12, 24V DC

Duty cycle:

100%

Variation in voltage:

10% nominal voltage


Protection class IP65 with connector

Dimensions
W

G80 - H

20

70

56.5

G80 - HW

25

75

61.5

Valve

2.28

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Added-on Manifold,


Direct operated solenoid valves
General Description
These valves are based on the GEVA 80 operator
with 8mm diameter plunger. Due to its relatively low
power consumption, the valve can be directly operated
from an electronic controller.
With these units, you can assemble your own manifold by
adding segments.
The valves are used mainly in pneumatic applications as
a pilot valve, but can be used for gas, water and light oils.

Notes
Valves are 100% inspected at 10 bar. Valves for
higher pressure are available upon special request.
See table for maximum pressures.
Valves for pressure higher than 12 bar are less
manual override.
The valves are AC or DC designated.
The coil can be mounted in 2 positions at
180 apart.
The coil plug can rotate 2 positions at 180.
Each two units are joined together by two specific
screws. For the "first" stand a different kit of screws
is used.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

EX

OUT
IN

"

G80-C Stations
Specify
number
00-nn

Body (1)
Mazak

Port
1/8"BSP 10
1/8"NPT 11

Function
2W NC
3WNC

1
3

Orifice
1.2
1.6

2
3

Manual
override

Seals
NBR
Viton
EPDM

(1) For St.st tube add "s"

2.29

N
V
E

plastic

Voltage
W/out coil
6
12
24
110
230
other

0
1
2
3
5
7
9

Power
No coil
AC7.5W50Hz
AC6W60Hz
DC6.5W
AC4W50Hz
AC3W60Hz
DC3W

Connector
0
1
2
3
4
5
7

without
with
with bi
color LED
with LED
& surge
protection
other

0
1
2
3
9

GEVA-80 Index
Technical Specifications
Max. Pressure (Bar) 2W, 3W NC Table

Function:

2/2W & 3/2W NC

Port size:

G1/8" BSP or NPT

Pressure and flow:

Pressure rating according to both

Media:

Coil
Current/Power

orifice size and power rating

AC - 7.5W

15

12

10.5

(see electrical specifications)

AC - 4W

12

10

DC - 6.5W

15

12

10.5

DC - 3W

12

10

0.5

0.65

Fluid and gases with viscosity less


than 3 E

Temperature range:

Orifice (mm)
1
1.2 1.6

Fluid: -10 C to 80 C (with no

Flow factor Kv(L/min)

freezing)
Ambient: -10 C to 50 C
Materials (in contact
with media) :

Tube :

Responded time:

5 - 12msec

Weight:

63gr. (aluminium valve)

Brass or AISI 303 for St.st valves


Plunger & upper pole:
430 FR

Electrical specifications:

Seals:

Standard voltages:

24, 110, 230V AC


6, 12, 24V DC

Mazak

Duty cycle:

100%

Protection class IP65 with connector

Variation in voltage:

10% nominal voltage

NBR, Viton, EPDM


Base:

Dimensions

60.2

M4x0.7
DEEP 5
TYPx2

1.2

1.2

1.2

21.5

BSP
1/8

BSP
1/8

BSP
1/8

4.5
14

(1)

10.3

65

78.3

M5x0.8

PUSH

PUSH

1/8" BSP/NPT
DEEP 7
BOTH ENDS

7.3

18.2

PUSH

12

11.5

23 TYP

1/8" BSP/NPT
DEEP 7

23 x Stations

(1) Thread #10-32TPI UNF


is an available option

2.30

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Direct Operated


solenoid valves manifold
General Description
These valves are based on the GEVA 80 operator
with 8mm diameter plunger. Due to its relatively low
power consumption, the valves can be directly operated
from an electronic controller.
These manifolds are a convenient solution for control
panels.
The valves are used mainly in pneumatic
applications as a pilot valve, but can be
used for gas, water and light oils.

Notes
Valves are 100% inspected at 10 bar. Valves for
higher pressure are available upon special request.
See table for maximum pressures.
Valves for pressure higher than 12 bar are less
manual override.
The valves are AC or DC designated.
The coil can be mounted in 2 positions at
180 apart.
The coil plug can rotate 2 positions at 180.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

How to Order
Example : G80-M-081s1033N-311
Is a GEVA 80 8 station manifold, aluminium body with St.st. tube
1/8" BSP, 3W NC, 1.6mm orifice with NBR seals,
24V AC 7.5W 50Hz, with connector.

G80-M

#
Stations
Specify
00-12

Body (1)
Alum.
Brass
St.st

1
2
3

Port
M5
10UNF
1/8"BSP
1/8"NPT

Function
00
01
10
11

2WNC
3W NC
Specify

1
3
9

Orifice
1.2
1.6

(1) For St.st tube add "s"

2.31

2
3

Voltage

Seals
NBR
Viton
EPDM
Kalrez

N
V
E
K

W/out coil
6
12
24
110
230
other

0
1
2
3
5
7
9

Power
No coil
AC7.5W50Hz
AC6W60Hz
DC6.5W
AC4W50Hz
AC3W60Hz
DC3W

Connector
0
1
2
3
4
5
7

without
with
with bi
color LED
with LED
& surge
protection
other

0
1
2
3

GEVA-80 Index
Technical Specifications
Max. Pressure (Bar)2W, 3W NC Table

Function:

2/2, 3/2 Way NC

Port size:

G1/8" BSP or NPT, M5, #10UNF

Pressure and flow:

Pressure rating according to both

Media:

Orifice (mm)
1.2
1.6

orifice size and power rating

AC - 7.5W

12

10.5

(see electrical specifications)

AC - 4W

10

DC - 6.5W

12

10.5

DC - 3W

10

0.65

Fluid and gases with viscosity less


than 3 E

Temperature range:

Coil
Current/Power

Fluid: -10 C to 80 C (with no

Flow factor Kv(L/min)

freezing)
Ambient: -10 C to 50 C
Materials (in contact
with media) :

Tube :
Brass or AISI 303 for St.st valves
Plunger & upper pole:
430 FR
Seals:
NBR, Viton, EPDM, Kalrez
Base:
Al-6061, AISI 303 or Brass

Responded time:

5 - 12msec

Weight:

50gr. (aluminium valve)

Electrical specifications
Standard voltages:

24, 110, 230V AC 6, 12, 24V DC

Duty cycle:

100%

Variation in voltage:

10% nominal voltage


Protection class IP65 with connector

Dimensions

Station
2
3
4
5
6
7
8
9
10
11
12

2.32

Station
L(mm)
60
83
106
129
152
175
198
221
244
257
270

X(mm)
53
76
99
122
145
168
191
214
237
250
263

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Direct Operated


General Purpose 3/2 Way
General Description
These valves are based on the GEVA 80 operator
with 8mm diameter plunger. Due to its relatively low
power consumption, the valve can be directly operated
from an electronic controller.
The valve concept enables the usage of the same valve
in various functions.
Thanks to the concept, larger orifices than in other
valves of this family are available.
The valves are used mainly in pneumatic applications
as a pilot valve, but can be used for gas, water and
light oils.

Notes
Valves are 100% inspected at 10 bar. Valves for
higher pressure are available upon special request.
See table for maximum pressures.
Valves for pressure higher than 12 bar are less
manual override.
The valves are AC or DC designated.
The coil can be mounted in 4 positions at
90 apart.
The coil plug can rotate 2 positions at 180 .
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

How to Order
Example : G80-X-11094V0-330
Is a GEVA 80 direct operated general purpose valve,
aluminium base, 1/8, 3W, 2mm orifice with Viton seals,
without manual override, 24V DC 6.5W 60Hz and without connector.

G80-X

Body
Alum.

(1)

Port
1/8"BSP
1/8"NPT

Function
10
11

general
purpose

Orifice
1.2
1.6
2
2.4

Seals
2
3
4
5

NBR
Viton
EPDM
Kalrez

(1) For St.st tube add "s"

2.33

Manual
override
N None
V
E
K

Voltage
W/out coil
6
12
24
110
230
other

0
1
2
3
5
7
9

Power
No coil
AC7.5W50Hz
AC6W60Hz
DC6.5W
AC4W50Hz
AC3W60Hz
DC3W

Connector
0
1
2
3
4
5
7

without
with
with bi
color LED
with LED
& surge
protection
other

0
1
2
3

GEVA-80 Index
Technical Specifications
Function:

3/2 Way NC,NO diverter or selector

Port size:

G1/8" BSP or NPT

Pressure and flow:

Max. Pressure (Bar)

1.2

orifice size and power rating

AC - 7.5W

12

3.5

(see electrical specifications)

DC - 6.5W

12

3.5

0.65

1.2

1.6

2.0

Pressure rating according to both

Media:

3W NC Table

Coil
Current/Power

Fluid and gases with viscosity less

Flow factor Kv(L/min)

Orifice (mm)
1.6
2

2.4

than 3 E
Temperature range:

Fluid: -10C to 80C (with no


freezing)
Ambient: -10 C to 50 C

Materials (in contact


with media) :

Tube :
Brass
Plunger & upper pole:
430 FR
Seals:
NBR, Viton, EPDM, Kalrez
Base:
Al-6061

Responded time:

5 - 12msec

Electrical specifications
Standard voltages:

24, 110, 230V AC 6, 12, 24V DC

Duty cycle:

100%

Variation in voltage:

10% nominal voltage


Protection class IP65 with connector

Dimensions

14

M3 DEEP 6
TYP x 2

31.75

22

1/8 BSP
TYP x 3

9.85

20

40

19.15

78.7

15

2.34

SV-05-10

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Direct Operated


General Purpose Manifold
General Description
These manifold valves are based on the GEVA 80
operator with 8mm diameter plunger. Due to its relatively
low power consumption, the valves can be directly operated
from an electronic controller.
The valve concept enables the usage of the same valve
in various functions.
Thanks to the concept, larger orifices than in other valves
of this family, are available.
The valves are used mainly in pneumatic applications as
a pilot valve, but can be used for gas, water and
light oils.

Notes
Valves are 100% inspected at 10 bar. Valves for
higher pressure are available upon special request.
See table for maximum pressures.
Valves for pressure higher than 12 bar are less
manual override.
The valves are AC or DC designated.
The coil can be mounted in 2 positions at
90 apart.
The coil plug can rotate 2 positions at 180.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

How to Order
Example : G80-MX-0611094V0-330
Is a GEVA 80 6 station direct operated general purpose
manifold, aluminium base, 1/8" BSP, 3W , 2mm orifice
with Viton seals, without manual override, 24V DC coil,
6.5W and without connector.
#
G80-MX Stations
Specify
00-12

Body (1)
Alum.

Port
1/8"BSP 10
1/8"NPT 11

Function Orifice
general 9
purpose

1.2
1.6
2
2.4

2
3
4
5

(1) For St.st tube add "s"

2.35

Manual
override

Seals
NBR
Viton
EPDM
Kalrez

N
V
E
K

None

Voltage
W/out coil
6
12
24
110
230
other

0
1
2
3
5
7
9

Power
No coil
0
AC7.5W50Hz 1
AC6W60Hz 2
DC6.5W
3
AC4W50Hz 4
AC3W60Hz 5
DC3W
7

Connector
without
with
with bi
color LED
with LED
& surge
protection
other

0
1
2
3

GEVA-80 Index
Technical Specifications
Function:

3/2 Way NC,NO diverter or selector

Port size:

G1/8" BSP or NPT

Pressure and flow:

Media:

Max. Pressure (Bar)

3W NC Table

Coil
Current/Power

1.2

1.6

2.4

orifice size and power rating

AC - 7.5W

12

3.5

(see electrical specifications)

DC - 6.5W

12

3.5

0.65

1.2

1.6

2.0

Pressure rating according to both

Fluid and gases with viscosity less

Flow factor Kv(L/min)

Orifice (mm)

than 3 E
Temperature range:

Fluid: -10 C to 80 C (with no


freezing)
Ambient: -10 C to 50 C

Materials (in contact


with media) :

Tube :
Brass
Plunger & upper pole:
430 FR
Seals:
NBR, Viton, EPDM, Kalrez
Base:
Al-6061

Responded time:

5 - 12msec

Electrical specifications
Standard voltages:

24, 110, 230V AC

6, 12, 24V DC

Duty cycle:

100%

Variation in voltage:

10% nominal voltage


Protection class IP65 with connector

Dimensions

"X"

12

1/8 BSP
TYP

23

29
40

9.85

78.7

14.875

M4 DEEP 6
TYP x 2

8.275
"L"

19.875

31.75

Station
2
3
4
5
6

2.36

Station
L(mm)
70
93
116
139
162

X(mm)
58
81
104
127
150

SV-05-10

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Pilot Operated


1/4", 3/8", 1/2", 3/4", 1" 2/2 Way NC, NO

Flow

3/4", 1"

1/4", 3/8", 1/2"

How to Order
Example : G80-S-2201V0-321
Is a GEVA 80 pilot operated valve, Brass, 1/4"BSP,
2WNC, Viton seals, without manual override,
24V AC 6W 60Hz, with connector.
(1)

Port

Brass
2
Nylon (2) 4

1/4" BSP
1/4" NPT
3/8" BSP
3/8" NPT
1/2" BSP
1/2" NPT
3/4" BSP
3/4" NPT
1" BSP
1" NPT

Body

G80-S

(1) For St.st tube add "s"


(2) 3/8" & 1/2" only

Function
20
21
30
31
40
41
50
51
60
61

2W NC
2W NO

1
2

Manual
Override

Seals
NBR
Viton
EPDM
Kalrez

N
V
E
K

None

2.37

Voltage
W/out coil
6
12
24
110
230
other

0
1
2
3
5
7
9

Power
No coil
AC7.5W50Hz
AC6W60Hz
DC6.5W
AC4W50Hz
AC3W60Hz
DC3W

Connector
0
1
2
3
4
5
7

without
0
1
with
with bi-color 2
LED
3
with LED
and surge
protection
9
other

GEVA-80 Index
Technical Specifications
Pressure and flow table

Function:

2/2 Way NC, NO

Ports size:

1/4", 3/8", 1/2", 3/4",1" BSP & NPT

Size

Orifice
(mm)

Pressure and flow:

See table

1/4"

Temperature range:

Fluid: max 80 C
Ambient: -10 C to 50 C

Materials in contact
with fluid :

Main valve :

3/8"

1/2"

12

Kv
(L/Min)

Pressure

12
0.5-10

16
35

Valve Specification NC Type

Brass - hot stamping, upon request

Port

dezinced brass (Cz132)

Orifice

Kv

Connection (mm) (L/min)

or Nylon 66
Solenoid operator:

Pressure Range Weight


(gf)
AC
DC

*less coil

3/4"

20

130

0.3-12 0.3-12

690

1"

25

200

0.5-12 0.5-12

980

Brass and Stainless steel


400 series
Valve Specification NO Type

Seals: NBR, Viton, EPDM, Kalrez

Port

Electrical specifications

Orifice

Kv

Connection (mm) (L/min)

Standard voltages:

24, 110, 230V AC 6, 12, 24V DC

Duty cycle:

100%

Variation in voltage:

10% nominal voltage

Pressure Range Weight


(gf)
AC
DC

*less coil

3/4"

20

130

0.3-10 0.3-10

690

1"

25

200

0.5-10 0.5-10

980

* Coil weight approx.110(gf), connector approx.25(gf)

Protection class IP65 with connector

Size

1/4"-3/8"

58

86

22

32

65

1/4"-3/8"BSP/NPT

125

11

M5X0.8

22

1/2"

70

90

27

38

68

1/2" BSP/NPT

135

13.5

M5X0.8*

22*

Dimensions
* Not available in plastic

Port Size

3/4"BSP/NPT

90

96.3

32

55

3/4"

17

15

25

103

65

1"

21

16

29.5

109.50

1" BSP/NPT

100 102.8 38.5

49.2

C
C
D

D
E

2.38

L
A

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Pilot Operated 16mm


1/2", 3/4" 2/2 Way NC, NO
General Description
Geva 80 pilot operated 2/2 way NC, NO solenoid valves
are recommended for applications where high flow at
high pressure is required. They can be used in control
and automation systems.
The typical applications are: industrial furnace, heating
equipment, burners, oil and gas, autoclaves, dental
equipment, instrumentation, car washers, machine
industries and irrigation.

Notes
The working pressure is 12 bar.
A minimum pressure of 0.5 bar is required
for operation.
To order valves manufactured to your
specific requirements, please contact our
technical sales department.

How to Order
Example : G80-S-240r1V0-321

Flow Direction

Is a GEVA 80 pilot operated 16mm valve, Brass,


1/2"BSP, 2WNC, Viton seals, without manual override,
24V AC 6W 60Hz, with connector.

G80-S

Body
Brass

(1)

Port

1/2" BSP
1/2" NPT
3/4" BSP
3/4" NPT

Function
40r
41r
50r
51r

2W NC
2W NO

1
2

Manual
Override

Seals
NBR
Viton
EPDM
Kalrez

N
V
E
K

None

(1) For St.st tube add "s"

2.39

Voltage
W/out coil
6
12
24
110
230
other

0
1
2
3
5
7
9

Power
No coil
AC7.5W50Hz
AC6W60Hz
DC6.5W
AC4W50Hz
AC3W60Hz
DC3W

Connector
0
1
2
3
4
5
7

without
0
with
1
with bi-color 2
LED
3
with LED
and surge
protection
9
other

GEVA-80 Index
Technical Specifications
Pressure and flow table

Function:

2/2 way NC, NO

Ports size:

1/2", 3/4" BSP & NPT

Pressure and flow:

See table

Temperature range:

Fluid: max 80 C
Ambient: -10 C to 50 C

Size

Orifice
(mm)

1/2"

16

3/4"

16

Pressure

0.5 - 10

Kv
(L/Min)

60
80

Materials in contact
with fluid :

Main valve :
Brass - hot stamping, upon request
dezinced brass (Cz132)
Solenoid Operator:
Brass and Stainless steel 400 series
Seals:
NBR, Viton, EPDM, Kalrez

Electrical specifications:
Standard voltages:

24, 110, 230V AC

6, 12, 24V DC

Duty cycle:

100%

Variation in voltage:

10% nominal voltage


Protection class IP65 with connector

Dimensions

2.40

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Inline Pilot Operated


3/4", 1", 1-1/2", 2" 2/2 Way NC, NO

Flow

G80-S

Port
3/4"BSPT
3/4"NPT
1"BSPT
1"NPT
1-1/2"BSP
1-1/2"NPT
2"BSP
2"NPT

(1) 3/4, 1, 1-1/2, 2 valves


(2) 3/4, 1 valves

Function
50
51
60
61
70
71
80
81

2WNC
2WNO

Flow
control

Seals
1
2

PVC

with(1)
without(2)

2.41

Voltage
5
6

6
12
24
110
230

Power
1
2
3
5
7

AC7.5W50Hz
AC6W 60Hz
DC 6.5W
AC4W50Hz
AC3W60Hz
DC3W
Latch

Connector
1
2
3
4
5
7
L

without
with
with bi color
LED
with LED &
surge
protection
other

0
1
2
3
9

GEVA-80 Index
Technical Specifications
Flow and Orifice table

Function:

3/4", 1", 1-1/2", 2"

Connection:

Female BSPT or NPT thread

Size

Orifice
(mm)

Kv
(L/Min)

3/4"

27

140

1"

27

200

1-1/2"

55

520

2"

55

600

10Kg./cm2

Pressure range:

0.3 -

Max. Fluid Temp:

50C

Solenoid:

Geva 80
2WNC or 2WNO
solenoids
all voltages

Materials:

Body & Cover:


Reinforced Nylon
Spring:
AISI 302
Diaphragm:
PVC
Seals:
NBR, EPDM
Screws:
AISI 304
Solenoid:
Brass and St.st

Dimensions
A

3/4"

108

110

81

1"

114

110

81

1-1/2"

180

160

126

190

170

126

Size

with flow control

without flow control

2.42

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 External Pilot Operated


1/4", 3/8", 1/2" 2/2 Way NC
General Description
Geva 80 external pilot operated 2/2 way NC valves
are recommended for applications where high flow at
high pressure is required. They can be used in control
and automation systems, with different media fluids for
the pilot and the line.
The typical applications are: industrial furnace, heating
equipment, burners, oil and gas, autoclaves, dental
equipment, instrumentation, car washers, machine
industries and irrigation.

Notes

Pilot pressure

Pilot pressure should be at least 1 bar higher than


process fluid.
Stainless steel valves are available only in 3/8"
and 1/2".
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

Flow

How to Order
Example : G80-SE-2201N-321
Is a GEVA 80 external pilot operated valve, Brass,
1/4"BSP, 2WNC, NBR seals, 24V AC 6W 60Hz, with connector.

G80-SE

Body (1)

Port

2
3

1/4" BSP
1/4" NPT
3/8" BSP
3/8" NPT
1/2" BSP
1/2" NPT

Brass
St.st

Function
20
21
30
31
40
41

2W NC

Voltage

Seals
NBR
Viton
EPDM

N
V
E

6
12
24
110
230

(1) For St.st tube add "s"

2.43

1
2
3
5
7

Power
AC7.5W50Hz 1
AC6W60Hz 2
DC6.5W
3
AC4W50Hz 4
AC3W60Hz 5
DC3W
7

Connector
without
with
with bi-color
LED
with LED
and surge
protection
other

0
1
2
3

GEVA-80 Index
Technical Specifications
Pressure and flow table

Function:

2/2 Way NC

Ports size:

1/4", 3/8", 1/2" BSP & NPT

Pressure and flow:

See table

Temperature range:

Fluid: max 80 C

Size
1/4"

Ambient: -10 C to 50 C
Materials in contact
with fluid :

Orifice Pressure
Kv
(mm)
(bar) (L/Min)
8

3/8"

12

1/2"

12

12
1-10

25
35

Main valve :
Brass - hot stamping or St.st 316
Seals:
NBR, Viton, EPDM

Media:

Air, gas, water, fuel, oil etc

Solenoid & Coil:

Geva 80, 3W NO Solenoid voltages

Port
Size

1/4"

58

32

72.7 11.2

3/8", 1/2" 69

38

80.5

13

22

78.2 86.15

22

1/4"BSP/NPT

27.6

83.7 93.45

22

3/8",1/2"BSP/NPT

Dimensions

2.44

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Zero Differential Pressure


1/8", 1/4" 2/2 Way NC
General Description
Geva 80 Zero differential pressure 2/2 way NC solenoid
valves are recommended for heavy duty applications
where high flow is required.
They can be operated with differential pressure up to
8 bar.
The valves' main advantage is in applications where the
pressure values can vary from a very low pressure to a
few bars and where high flow is needed.

Notes
Maximum pressure for use at nominal voltage + 10%.
For further information, please consult our engineers.
When switching from an AC coil to a DC coil, the
solenoid operator must be changed too.

How to Order
Example : G80-Z-2201N-231
Is a GEVA 80 Zero differential Brass 1/4" BSP,
2WNC, NBR seals, 12V DC 6.5W with connector.

G80-Z

Body
Brass

(1)
2

Port
1/8"BSP
1/8"NPT
1/4"BSP
1/4"NPT

Function
10
11
20
21

2WNC

Seals
1

NBR
EPDM
Kalrez

(1) For St.st tube add "s"

2.45

Voltage
N
E
K

W/out coil
6
12
24
110
230
other

Power
0
1
2
3
5
7
9

No coil
AC7.5W50Hz
AC6W 60Hz
DC 6.5W

Connector
0
1
2
3

without
with
with bi color
LED
with LED &
surge
protection

0
1
2
3

GEVA-80 Index
Technical Specifications
Function:

2/2 Way NC

Port size:

1/8", 1/4" BSP & NPT

Pressure and flow:

See table

Temperature range:

Fluid: max 80 C

Pressure and flow table NC


Size

Orifice (mm)

1/8", 1/4"

Pressure
AC
DC
0-10

0-6

Kv (L/Min)
10

Ambient: -10 C to 50C


Materials

Main Valve:
Brass
Solenoid operator:
Brass, Stainless steel 303
& 400 series
Seals:
NBR, EPDM, Kalrez

Media:

Air, Inert gas, Water

Coil voltage:

All Baccara coils voltages + 10%


AC 7.5W DC 6.5W
Protection class IP65 with connector

Dimensions

2.46

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 Proportional 2/2 Way NC


Direct Operated Valve
General Description
This valve is a 2/2 Way normally closed direct
operating solenoid valve and is based on the
GEVA 80 solenoid valve. It is used as a control
valve in process control, medical systems etc.

Working Principle
The Solenoid Operator is used to create a magnetic
force. The balance between this force and the
returning spring at any current, is used to control
the plunger stroke which determines the valve opening.
The magnetic force is direct associated to the current
passing in the coil.
The fluid enters the valve below the seat. The fluid
pressure together with the magnetic force acts against
the return spring. Setting this spring will change the
minimum current needed to open the valve, and by that,
the minimum flow.

Notes

Out

In

Flow

Because this is a specialized valve, we recommend


that you contact our engineering department in the
planning phase.

How to Order
Example : G80-PR-21015N0-1
Is a GEVA 80 Proportional direct operating,
Brass, 1/8" BSP 2WNC, 2.4 orifice, NBR,
without manual override, with connector.

G80-PR

Body (1)
Alum.
Brass
St.st

1
2
3

Port
M5
10 UNF
1/8"BSP
1/8"NPT

Function
00
01
10
11

2WNC

Input Control

Orifice
1
1.2
1.6
2.0
2.4
3.0
other

Manual
Override

Seals
1
2
3
4
5
6
9

NBR
Viton
EPDM

(1) For St.st tube add "s"

2.47

N
V
E

None

Connector
without
with

0
1

GEVA-80 Index
Technical Specifications
Function:
Ports size:
Orifice:
(2)
Kv :
Pressure range:
Temperature range:
Materials in contact
with fluids

Weight (with coil):


Media:
Mounting:

2/2 Way NC
Maximum Working Pressure (bar)
M5 and 1/8" BSP & NPT
Orifice Size (mm)
1
1.2 1.6
2.0
See table
(3)
Pressure
rating
[bar]
10
8
6
5
See table
Vacuum - see table
Kv (l/min)
0.5
0.65 1.0
1.6
Fluid: -10C to 80C
Ambient: -10 C to 55 C
Main valve :
Aluminum, Brass,
Stainless steel
Solenoid Operator:
Stainless St. 300/400 series
Seals:
NBR, Viton or EPDM (other on request)
Guide Rings: PTFE
50 gr (aluminum base)
Neutral gases, water, oil
2
Max. Viscosity 21mm /s
In any position, preferably upright

2.4

3.0

2.5

2.0

2.8

Electrical Specification:
The Control Parameter is the current in the Coil!
Operating Current:
100-500 [mA]
Standard voltage 24 VDC(=)
Protection Class:
IP65 with connector
Coil terminal:
Per DIN 43650-b, or
2 flying leads 18AWG
300mm length.

Dimensions
2X M3 DEEP 6

2.48

PORT

M5/10 UNF

5.5

51.5

1/8

10

58.5

SV-04-09

Technical Info

GEVA-80 Index
BACCARA

GEVA 80 CHEM-SOL 1/8"


2/2 Way NC, NO
General Description
These GEVA 80 2/2 way NC, NO Chem-Sol
solenoid valves are recommended for use in
applications where corrosive fluid must be
controlled, such as chemical process, water
treatment, analysis device etc.
They can be used for industrial and irrigation
control and automation systems.
NC

NO

Notes
Contact our technical department to get
details on valve and fluid compatibility.
To order valves manufactured to your
specific requirements, please contact
our technical department.

Flow direction

How to Order
Example : G80-CS-41012V-321
Is a GEVA-80 Chem-Sol, 1/8"BSP, 2W NC,
Pressure, Viton, 24V AC 6W 60Hz with connector.

G80-CS Body
PVC

Port

Function

1/8"BSP 10 2W NC
1/8"NPT 11 2W NO

1
2

Pressure
Vacuum 1
Pressure 2

Seals
Viton
EPDM

2.49

Voltage
V
E

W/out coil
6
12
24
110
230
other

0
1
2
3
5
7
9

Power
0
No coil
AC7.5W 50Hz 1
AC6W 60Hz 2
3
DC6.5W
AC4W 50Hz 4
AC3W 60Hz 5
7
DC 3W

Connector
without
with
with bi color
LED

0
1
2

3
with LED &
surge protection
9
other

GEVA-80 Index
Technical Specifications
Functions:

2/2 Way NC or NO

Ports size:

1/8" BSP & NPT

Orifice:

4mm

Kv:

4 L/min

Pressure range:

-1 to 1 (for other, please consult with us)

Temperature range:

Fluid: -15 C to max 90 C


Ambient: -10 C to 50 C

Materials in contact
with fluid:

Main valve :
PVC
Diaphragm:
Viton, EPDM
Protection class IP65 with plug attached

Dimensions
14

1/8 BSP
TYPx2

26.2

59.8

2.50

7.5 TYPx2

57

22

14

FOR TAPPING SCREWS No. 3

SV-4-09

Main Contents

BACCARA

Section Three

GEVA 65

G65-B

Coil

3.1 - 3.2

G65-O

Operator

3.3 - 3.4

G65-A

Direct Operated 2/2W NC

3.5 - 3.6

G65-A

Direct Operated 3/2W NC

3.7 - 3.8

G65-M

Direct Operated Solenoid Valves Manifold

3.9 - 3.10

G65-PR

Proportional Direct Operated 2/2W NC

3.11-3.12

Technical Info

GEVA-65 Index
BACCARA

GEVA 65 COIL
General Description
G65 coils are designed to withstand industrial
ambient conditions. The coils are constructed
according to EN 60204.1 and used on G65
operators.
The coil includes part of the magnetic circuit
and moulded with high temperatures, with
resistance thermoplastic to withstand heavyduty requirements.

Notes
The coil should not be energized without
being assembled on operator.
The coils are designed to operate at 10% of
rated voltage.
The coils are suitable to operate at 100% duty
cycle, however when using high power coils for
a long time, the temperature developed may affect
solenoid seals. Viton seals or lower power coils
are advised.
For outdoor applications or when the coil is
exposed to high humidity, please contact our
technical department.

How to Order

G65-B

Voltage

Power

Connector

Example : G65-B-331
Is a G65 Coil 24V DC 2.9W
with connector.

12
24
110
230

3.1

2
3
5
7

AC3.8VA 50Hz
DC 2.9W

1
3

without
with

0
1

GEVA-65 Index
Technical Specifications
Electrical specifications
Standard voltages:

24,110, 230V AC (50 or 60 Hz) 12, 24V DC

Variation in voltage:

Over voltage category II 10% nominal voltage

Duty cycle:

100%

Coil temperature:

-20 C to 70 C ambient

Isolation class:

F 155

Protection grade:

IP65 (with connector) - dust and splash proof

Coil terminal:

AMP 6.3x0.8 DIN 43650, 2 poles + 1 earth

Connector:

Din 43650, fixture: M3 screws, 2 positions at 180

Assembly:

On a valve, 4 positions at 90

Fixing:

On a G65 operator with MF6x0.75 nut

Weight:

Approx 51 gr.

Power Ratings
50 Hz

DC

Inrush power (VA)


Holding (VA)

3.8

Rated power DC (W)

2.9

Dimensions
6

M2.5

18.5

27

2x2

3x0.8

7.4
3.4
22.5
25.5

16.5

8.5

10.5

11
36.5

3.2

SV-04-10

Technical Info

GEVA-65 Index
BACCARA

GEVA 65 OPERATOR
General Description
The operator is designed to be assembled on a valve
or a counterpart to set up a solenoid valve.
According to the operator and valve construction,
various functions are available.
The G65 operators may be used with alternate or
direct current.

Notes
Operator cavity should be designed according
to our specifications, see drawing on the
next page.
Operator for DC is without shading ring and may
not be used for AC.
When assembling coil take care not to tighten
nut excessively.
Valves are inspected at general pressure of
up to 10 bar. Higher pressures are available,
please consult our technical sales department.
For applications where abnormal conditions exist
and for fluids other than air, water or inert gases,
please consult our technical sales department.
To order valves manufactured to your specific
requirements, please consult our technical sales
department.

2W

3W

How to Order
Example : G65-O-2103-N-331
Is a G65 operator, Brass tube, 2WNC, DC, 1.2 orifice,
NBR seals, 24V DC 2.9W with connector.

Example : G65-O-3303-N-331
Is a G65 operator, St.st tube, 3WNC, DC, 1.2 orifice,
NBR seals, 24V DC 2.9W with connector.
2W

G65-O

Tube
Brass
St.st

Function
2
3

2WNC

Current
DC
AC

0
1

Orifice
0.8
1
1.2

1
2
3

3W

G65-O

Tube
Brass
St.st

Function
2
3

3WNC

Current
DC
AC

0
1

Orifice
0.8
1
1.2

Voltage

Seals

1
2
3

3.3

NBR
Viton
EPDM

N
V
E

W/out coil
12
24
110
230

0
2
3
5
7

Connector

Power
AC3.8VA50Hz
DC 2.9W

1
3

without
with

0
1

GEVA-65 Index
Technical Specifications
Function:

2/2, 3/2 Way NC

Threads on

Orifice size:

0.8, 1, 1.2mm

operator tube:

M6x0.75

Pressure range(bars):

Standard up to 10

Operator assembly:

Insert operator into

Flow factor Kv(l/min):

See solenoid valve performances

cavity, tighten it by the

Temperature range:

Fluid: max 80 C

flange and the two M2.5

Ambient: -10 C to 50 C

screws. Fix the coil with

Response time:

5 - 12 msec

one M6x 0.75 nut.

Cycling rate:

2000 cycles per minute

Materials in contact
with fluid :

Coil data:

See technical coil data

Standard voltage:

See "coil"

Operator :
Brass or Stainless steel
series AISI 300 & 400
Shading ring:
Copper
Orifice:
Stainless steel

Weight:

15 gr (without coil)

Media:

Air, inert gases and water

Dimensions

1.7+0.05

Operator seating

3.4

SV-04-09

Technical Info

GEVA-65 Index
BACCARA

GEVA 65 Direct operated


2/2 Way NC
General Description
These valves are based on the Geva 65 operator with
6.5mm plunger.
Due to its relatively low power consumption, the valve
can be directly operated from an electronic controller.
The valves are used mainly in pneumatic applications as a
pilot valve, but can be used for gas, water and light oils.

Notes
Valves are 100% inspected at 10 bar. Valves for
higher pressure are available upon special request.
See table for maximum pressures.
The valves are AC or DC designated.
The coil can be mounted in 4 positions, at 90 apart.
The coil plug can rotate 2 positions at 180 .
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

IN
OUT

How to Order
Example : G65-A-10012V0-010
Is a Geva 65 Direct operated valve, Aluminium base,
M5, 2W NC, orifice 1mm with Viton seals, without manual
override, without coil, AC 3.8VA 50Hz without connector.

G65-A

Body (1)
Alum.
Brass
St.st

1
2
3

Port
M5
10UNF

Function
00
01

2WNC

Orifice
0.8
1
1.2
1.6
2.0

Manual
override

Seals
1
2
3
4
5

NBR
VITON
EPDM

(1) For St.st tube add "s"

3.5

N
V
E

None

Voltage
w/out coil
12
24
110
230

Power

0 AC3.8VA50Hz 1
3
2 DC 2.9W
3
5
7

Connector
without
with
other

0
1
9

GEVA-65 Index
Technical Specifications
Function:

2/2 Way NC

Port size:

M5

Pressure and flow:

Media:

Max. Pressure (Bar) 2W NC Table


Coil
Current/Power

0.8

Orifice (mm)
1.0
1.2 1.6

orifice size and power rating

AC - 3.8VA

30

25

20

12

(see electrical specifications)

DC - 2.9W

30

25

20

Flow factor Kv(L/min)

0.4

0.5

0.65

1.2

1.6

Pressure rating according to both

Fluid and gases with viscosity less


than 3 E

Temperature range:

Fluid: -10 C to 80 C (with no


freezing)
Ambient: -10 C to 50 C

Materials (in contact


with media) :

Tube:
Brass, AISI 303
Plunger & upper pole:
430 FR
Seals:
NBR, Viton, EPDM
Base:
Al-6061, Brass, AISI 303

Responded time:

5 - 12(msec)

Weight:

30gm (aluminium valve)

Electrical specifications
Standard voltages:

24, 110, 230V AC 12, 24V DC

Duty cycle:

100%

Variation in voltage:

10% nominal voltage


Protection class IP65 with connector

Dimensions
M3 DEEP 6
TYP x 2

15

3.6

SV-04-09

Technical Info

GEVA-65 Index
BACCARA

GEVA 65 Direct operated


3/2 Way NC
General Description
These valves are based on the Geva 65 operator with
6.5mm plunger.
Due to its relatively low power consumption, the valve
can be directly operated from an electronic controller.
The valves are used mainly in pneumatic applications as a
pilot valve, but can be used for gas, water and light oils.

Notes
Valves are 100% inspected at 10 bar. Valves for
higher pressure are available upon special request.
See table for maximum pressures.
Valves for pressure higher than 12 bar are less
manual override.
The valves are AC or DC designated.
The coil can be mounted in 4 positions, at 90 apart.
The coil plug can rotate 2 positions at 180 .
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

How to Order
Example : G65-A-10032V0-010
Is a Geva 65 Direct operated valve, Aluminium base,
M5, 3W NC, orifice 1mm with Viton seals, without manual
override, without coil, AC 3.8VA 50Hz without connector.

G65-A

Body
Alum.
Brass
St.st

Port
1
2
3

M5
10UNF

Function
00
01

3WNC

Orifice
0.8
1
1.2

Seals
1
2
3

NBR
Viton
EPDM

3.7

N
V
E

Manual
override
None

Voltage
w/out coil
12
24
110
230

0
2
3
5
7

Power
AC3.8VA50Hz 1
DC 2.9W
3

Connector
without
with
other

0
1
9

GEVA-65 Index
Technical Specifications
Max. Pressure (Bar) 3W NC Table

Function:

3/2 Way NC

Port size:

M5

Pressure and flow:

Pressure rating according to both

Media:

Coil
Current/Power

Orifice (mm)
0.8
1.0
1.2

orifice size and power rating

AC - 3.8VA

10

8.5

5.5

(see electrical specifications)

DC - 2.9W

10

8.5

5.5

Flow factor Kv(L/min)

0.4

0.5

0.65

Fluid and gases with viscosity less


than 3 E

Temperature range:

Fluid: -10 C to 80 C (with no


freezing)
Ambient: -10 C to 50 C

Materials (in contact


with media) :

Tube:
Brass
Plunger & upper pole:
430 FR
Seals:
NBR, Viton, EPDM
Base:
Al-6061 or Brass

Responded time:

5 - 12(msec)

Weight:

30gm (aluminium valve)

Electrical specifications
Standard voltages:

24, 110, 230V AC 12, 24V DC

Duty cycle:

100%

Variation in voltage:

10% nominal voltage


Protection class IP65 with connector

Dimensions
M3 DEEP 6
TYP x 2

3.8

SV-04-09

Technical Info

GEVA-65 Index
BACCARA

GEVA 65 Direct operated


solenoid valves manifold
General Description
These valves are based on the Geva 65 operator with
6.5mm plunger.
Due to its relatively low power consumption, the valves
can be directly operated from an electronic controller.
These manifolds are a convenient solution for control
panels.
The valves are used mainly in pneumatic applications as a
pilot valve, but can be used for gas, water and light oils.

Notes
Valves are 100% inspected at 10 bar. Valves for
higher pressure are available upon special request.
See table for maximum pressures.
The valves are AC or DC designated.
The coil can be mounted in 2 positions, at 180 apart.
The coil plug can rotate 2 positions at 180 .
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

How to Order
Example : G65-M-0810133N-311
Is a Geva 65 8 station manifold, Aluminium body,
10UNF, 3W NC, orifice 1.2mm with NBR seals,
24V AC 3.8VA 50Hz with connector.

G65-M

#
Stations
Specify
00 - 12

Body
Alum.

Port
1

M5
10UNF

Function
00
01

2WNC
3WNC

1
3

Orifice
0.8
1
1.2

3.9

Voltage

Seals
1
2
3

NBR
Viton
EPDM

N
V
E

w/out coil
12
24
110
230

0
2
3
5
7

Power

Connector

AC3.8VA50Hz 1 without
3 with
DC 2.9W
other

0
1
9

GEVA-65 Index
Technical Specifications
Max. Pressure (Bar) 2W, 3W NC Table

Function:

2/2, 3/2 Way NC

Port size:

M5 or 10UNF

Pressure and flow:

Pressure rating according to both

Coil
Current/Power

orifice size and power rating


(see electrical specifications)
Media:

Fluid and gases with viscosity less

Orifice (mm)
0.8 1.0
1.2

AC - 3.8VA

10

8.5

5.5

DC - 2.9W

10

8.5

5.5

Flow factor Kv(L/min)

0.4

0.5

0.65

than 3 E
Temperature range:

Fluid: -10 C to 80 C (with no


freezing)
Ambient: -10 C to 50 C

Materials (in contact


with media) :

Tube :
Brass
Plunger & upper pole:
430 FR
Seals:
NBR, Viton, EPDM
Base:
Al-6061

Responded time:

5 - 12msec

Electrical specifications
Standard voltages:

24, 110, 230V AC 12, 24V DC

Duty cycle:

100%

Variation in voltage:

10% nominal voltage


Protection class IP65 with connector

Dimensions

Station
2
3
4
5
6
7
8
9
10
11
12

3.10

Station
L(mm)
42
59
76
93
110
127
144
161
178
195
212

X(mm)
49
66
83
100
117
134
151
168
185
202
219

SV-04-09

Technical Info

GEVA-65 Index
BACCARA

GEVA 65 Proportional 2/2 Way NC


Direct Operated Valve
General Description
This valve is a 2/2 Way normally closed, direct
operating solenoid valve and is based on the
GEVA 65 solenoid valve. It is used as a control
valve in process control, medical systems etc.

Working Principle
The solenoid operator is used to create a magnetic
force. The balance between this force and the
returning spring at any current, is used to control
the plunger stroke which determines the valve opening.
The magnetic force is direct associated to the current
passing in the coil.
The fluid enters the valve below the seat. The fluid
pressure together with the magnetic force acts against
the return spring. Setting this spring will change the
minimum current needed to open the valve, and by that,
the minimum flow.

Notes

Out
In

Flow

Because this is a specialized valve, we recommend


that you contact our engineering department in the
planning phase.

How to Order
Example : G65-PR-2s1014N0-1
Is a GEVA 65 Proportional direct operating,
brass with Stainless steel tube, 1/8" BSP 2WNC,
1.6 orifice, NBR, without manual override, with connector.

G65-PR

Body (1)
Alum.
Brass
St.st

1
2
3

Port
M5
10 UNF
1/8"BSP
1/8"NPT

Function
00
01
10
11

2WNC

Orifice
0.8
1
1.2
1.6

Input Control

Manual
Override

Seals
1
2
3
4

NBR
Viton
EPDM

(1) For St.st tube add "s"

3.11

N
V
E

None

Connector
without
with

0
1

GEVA-65 Index
Technical Specifications
Function:
Ports size:
Orifice:
Kv(2):
Pressure range:
Temperature range:

2/2 Way NC
Maximum Working Pressure (bar)
M5 and 1/8" BSP & NPT
Orifice Size (mm)
0.8
1
1.2
1.6
See table
(3)
Pressure
rating
[bar]
10
8
6
4
See table
Vacuum - see table
Kv (l/min)
0.4
0.5 0.65 1.2
Fluid: -10 C to 80 C
Ambient: -10 C to 55 C
(1) From technical vacuum to max.rating
Materials in contact
Main valve :
with fluids
Aluminum, Brass,
Flow regulation :
Stainless steel
With Control unit P.W.M 500[Hz], measured at
Solenoid Operator:
constant
P (delta P).
Stainless St. 300/400 series
Hysteresis
<5% of F.S.
Seals:
Repeatability
<3% of F.S.
NBR, Viton or EPDM (other on request)
Sensitivity
<2% of F.S.
Guide Rings: PTFE
Weight (with coil):
50 gr (aluminum base)
Media:
Neutral gases, water, oil
2
Guidelines for selection GEM-PR valve
Max. Viscosity 21mm /s
1. The pressure drop ( P) on the valve should be
Mounting:
In any position, preferably upright
30-50% or higher, of the total pressure drop in the
system.
2. Special consideration should be taken in choosing
Electrical Specification:
the right Kv of the valve as this factor determines
The Control Parameter is the current in the Coil!
the flow and pressure drop of the valve.
Operating Current:
max 150 [mA]
3. To achieve better regulation performance when
Standard voltage 24 VDC(=)
working without a control unit, the maximum
Protection Class:
IP65 with connector
pressure should be 1.2 times the working pressure.
Coil terminal:
Per DIN 43650-b, or
The maximum pressure can be adjusted using
2 flying leads 18AWG
the upper screw.
300mm length.
4. Inlet pressure should be kept constant during
operation.

12

M3x0.5
DEEP 5
TYPx2

15
22.1

50.6

63

52.9

15

Dimensions

M5x0.8
DEEP 7
TYPx2
16

3.12

SV-03-11

Main Contents

Technical Info

GEVA-60 Index
BACCARA

GEVA 60 1/8" Latch Solenoid Valve,


Pulse Operated 3/2 Way 2 or 3 wires
General Description
This valve has been designed to meet the high
standards required in electronic control irrigation
systems.
These systems, which can receive energy from
a limited source such as a battery, require a
valve capable of quick response time, long life,
resistance to extreme surrounding conditions and
lower power consumption.
The mechanical structure of the valve enables easy
and simple maintenance and is a result of vast
experience in this field.
The valve is made up of two separate parts:
electro-mechanical operator and mechanical valve.
The electro-mechanical operator is housed in a
sealed plastic structure.
The mechanical valve is made of high standard
anti-corrosive materials.
The valve has a knob on the bottom for manual
operation and to indicate valve position.

Up

Assembly notes
Valve assembly : valve must be assembled in upright
position only, with coil facing upwards and valve below.
Cable exiting from the coil must always face downwards.
Tube assembly : only as marked on valve body.
Filtering : the fluid must be filtered at level of 120 mesh
at least.

How to Order
Example : G60-41031
Is a Geva 60 1/8" Latch solenoid valve,
plastic, 1/8"BSP 24V DC with 2 wires

G60

Base
Brass
Plastic

Port
2
4

1/8" BSP
1/8" NPT

Electric
Connector

Voltage
10
11

12V DC
24V DC

2
3

4.1

2 wires
3 wires

1
2

GEVA-60 Index
Technical Specifications
GEVA 60 Electrical wiring 3 wires

18V+50%
30V +50%

Dimensions

C(F) V2(V)

4.2

2&3 wires

"GEVA 60" 12V 4700

18

2&3 wires

"GEVA 60" 24V 2200

30

SV-10-09

Technical Info

GEVA-60 Index
BACCARA

GEVA 60 Manifold Installation


General Description
The GEVA 60 manifold installation provides a
turn key solution.
Available with various types of GEVA 60
solenoid voltages.

How to Order
Example : G60-M-521021
Is a 5 station Geva 60 manifold with brass base,
1/8"BSP, 12V DC solenoids with 2 wires electric connection.

G60-M

#
stations
3
4
5
6
7
8
9
10
11
12

3
4
5
6
7
8
9
10
11
12

Base
Brass
Plastic

Port
2
4

1/8" BSP
1/8" NPT

Electric
Connector

Voltage
10
11

4.3

12V DC
24V DC

2
3

2 wires
3 wires

1
2

GEVA-60 Index
Technical Specifications
# stations

210

280

350

420

490

560

630

700

10

770

11

840

12

910

Dimensions

4.4

SV-10-09

Main Contents

BACCARA

Section Five

GEVA 75
G75-O

Solenoid Operator 2/2W, 3/2W

5.1 - 5.2

G75-O

Latch Solenoid Operator 2/2W, 3/2W

5.3 - 5.4

G75-A

1/8" Solenoid Valve

5.5 - 5.6

GALIT

Galit Pilot Operated Solenoid Valve 3/2W

5.7 - 5.8

G75-H

Hydraulic Relay 3/2W (Discontinued)

5.9 - 5.10

G75-S

Inline Electric Valve 3/4", 1", 1-1/2", 2" 2/2W

5.11 - 5.12

G75-S

Inline Hydraulic Valve 3/4", 1", 1-1/2", 2" 2/2W

5.13 - 5.14

G75-S

Pilot Operated 3/8", 1/2", 2/2W

5.15 - 5.16

G75-M

Manifold Installation

5.17 - 5.18

G75-C

Irrigation Controllers

5.19 - 5.20

G75-C

Irrigation Window Controllers

5.21 - 5.22

G75-C

Multi-Zone DC & AC Irrigation Controller

5.23 - 5.24

G75-S

Inline Hydraulic Valve 3/4", 1", 1-1/2", 2" Line pilot

5.25

G-75-S

Inline Hydraulic Valve 1-1/2", 2" External pilot 3/2W

5.26

G75-S

Inline Hydraulic Valve 1-1/2", 2" Level float valve

5.27

G75-S

Inline Hydraulic Valve 1-1/2", 2" Level float valve with shut off solenoid

5.28

G75-S

Inline Hydraulic NC Valve 1-1/2", 2" External solenoid 3/2W NO

5.29

G75-S

Inline Hydraulic NO Valve 1-1/2", 2" External solenoid 3/2W NC

5.30

G75-S

Inline Hydraulic NC Valve 3/4", 1", 1-1/2", 2" Manual selector

5.31

G75-SM

Inline Hydraulic NC Valve 1-1/2", 2" External solenoid

5.32

3/2W NO and a Manual selector


G75-SR

Inline Hydraulic NC Valve 3/4", 1",1-1/2", 2" Pressure relief

5.33

G75-PR

Inline Valve 1-1/2", 2" Electrical and Hydraulic pressure reducing

5.34

G75-PR

Inline Valve 1" Electrical and Hydraulic pressure reducing

5.35 - 5.36

G75-Z

Inline Hydraulic Valves 3/4", 1",1-1/2",2" 2/2W, Zero pressure

5.37 - 5.38

G75-DP

Digital Differential Pressure Gauge Switch (DDPGS)

5.39 - 5.40

G75-LDO

Long Distance Operator (LDO) 2/2, 3/2W

5.41 - 5.42

Technical Info

GEVA-75 Index
BACCARA

GEVA 75 Solenoid Operator


2/2, 3/2 Way NC, NO
General Description
The 2/2, 3/2 Way, NC, NO operator is compatible with
the 3/4-20 UNF operator seat.
Polyurethane encapsulated construction and exclusion of air
assures complete sealing for the coil and lead wires entry.
Wet metal parts are made of passivated Stainless
steel for maximum corrosion protection.
An efficient design makes it possible to achieve high
pressures with a low inrush and holding current and
wide voltage tolerance.

Notes
Coils for other voltages are available, please
contact our technical sales department.
Available with brass adaptor upon request.

How to Order
Example : G75-O-2W1-1
Is a Geva 75 Operator, 2WNC, 24V AC.

Example : G75-O-1032-1
Is a Geva 75 Operator, 1/8 BSP, 3WNC,
1.2 orifice, 24V AC.

2WNC

2W

G75-O

2W

Function
2WNC

Voltage
24V AC
12V AC
12V DC
24V DC
110V AC (1)

3W

G75-O

Port
1/8"BSP
1/8"NPT

Function
10
11

3WNC
3WNO

3
4

Orifice
1
1.2
1.6

1
2
3

(1) 110V AC - available in 2/2W only

5.1

1
3
4
5
7

3WNC/3WNO

GEVA-75 Index
Technical Specifications
Voltage:

Solenoid
2W 50 Hz

Current:

2W 60 Hz
3W 50 or 60 Hz

Voltage Inrush [A]


0.3
+10%
0.2
n-20% 0.125

DC

Working Pressure 2W NC

Holding[A]
0.19

Orifice

0.14
0.125

up to 2.0

Pressure (bar)

12

4.5W

Electric connection:

Lead wires 35 cm, 18 Awg

Protection:

IP66

Ambient Temp:

Max 60 C

Fluid Temp:

Max 80 C

Working Pressure 3W NC
Orifice

Materials
Housing:

Reinforced Nylon 66

Plunger and Pole:

Passivated AISI430F

Rubber Seal:

EPDM

Encapsulate:

Polyurethane

1.0

1.2

1.6

AC Pressure (bar) 16

11

DC Pressure (bar) 12

Working Pressure 3W NO
Orifice

1.0

1.2

1.6

Pressure (bar)

16

12

3/4" 20TPI UNEF

2+0.2

10

5.5

6.5

12

Max2.0

Operation seating

Dimensions

1/2" NPT

30
CABLE LENGTH
350 (mm)
BLACK WIRE

1/8" BSP/NPT
30

47

1.2
SOLENOID ON

1.2

54
9

SOLENOID ON

CABLE LENGTH
350 (mm)
BLACK/RED

58

1.2
SOLENOID ON

110V with 1/2 NPT

3/4"-UNEF-20TPI
3/4"-20 UNEF-2B
PLUNGER STROKE 1+- 0.1

24

3/4"-20 UNEF-2B
PLUNGER STROKE 1+- 0.1

3WNC/3WNO

33.5
29.8

2WNC

CABLE LENGTH
350 (mm)
BLACK WIRE

5.2

SV-04-09

Technical Info

GEVA-75 Index
BACCARA

GEVA 75 Latch Solenoid Operator


2/2, 3/2 Way NC, NO
General Description
The 2/2, 3/2 Way, NC, NO operator is compatible with
the 3/4-20 UNF operator seat.
Polyurethane encapsulated construction and exclusion of air
assures complete sealing for the coil and lead wires
entry. Wet metal parts are made of passivated Stainless
steel, for maximum corrosion protection.
The two wire operator consists of one coil with exit of two
lead wires. Electrical operation by reversing the current, by
use of transistors or relays.
The three wire operator consists of one coil and an
integrated electrical circuit.

Notes
Two wires: to pull the plunger up, connect the black
wire (-) and the green to the (+).
Three wires: to pull the plunger up, pulse is given to
the red wire (-). To release the plunger, a pulse is
given to the black wire (-).
To avoid damage to the electronic circuit, operate
the three wires solenoid only by a controller.
Available with brass adaptor upon request.
Coils for other voltages are available, please
contact our technical sales department.

2WNC

3WNC/3WNO

2W

G75-O

2W

Voltage
VDC

Function
2WNC

B
C
D
6

3W

G75-O

Port
1/8"BSP
1/8"NPT

Function
10
11

3WNC
3WNO

Orifice
3
4

1
1.2
1.6

Wires

1
2
3

5.3

two
three

null
a

GEVA-75 Index
Technical Specifications
Working Pressure 2W NC
Orifice

up to 2.0

Pressure (bar)

12

Working Pressure 3W NC
Orifice

1.0

1.2

1.6

Pressure (bar)

16

11

Working Pressure 3W NO
Orifice

1.0

1.2

1.6

Pressure (bar) 16

12

Various Controllers Adaption Table


Controller Type
Baccara
Talgil
Motorola
Alextronix
Q.T.
Rainbird
Miracle
Galcon
Other

3/4" 20TPI UNEF

2+0.2

10

5.5

6.5

12

Max2.0

Operation seating

C[F]

Please consult

Dimensions

30
1/8" BSP/NPT

1.2

47

SOLENOID ON

58

CABLE LENGTH
350 (mm)
BLACK/GREEN

3/4"-20 UNEF-2B
PLUNGER STROKE 1 0.1

3WNC/3WNO

2WNC

5.4

SV-10-09

Technical Info

GEVA-75 Index
BACCARA

GEVA 75 1/8" Solenoid Valves


General Description
GEVA 75 1/8" solenoid valves are based
on GEVA 75 operators mounted on a plastic base.
These bases are available with or without flange,
manual override as standard.
For AC / DC in a latch configuration, manual
override will be supplied upon request.

Applications
They are specially designed for irrigation
control sytems.

Notes
Available with brass adaptor upon request.
For other availabe voltages and to order
valves manufactured to your specific
requirements, please contact our technical
sales department.

How to Order
Example : G75-A-110302-1
Is a GEVA 75 with flange, 1/8" BSP
3WNC, no manual override,
1.2 orifice, 24V AC coil.

G75-A

Type
with flange
1
without flange 2
Brass
3

(2)

Port
1/8" BSP
1/4" BSP (2)
1/8" NPT
1/4" NPT (2)

Manual (1)
Override

Function
10
20
11
21

2WNC
3WNC
3WNO

1
3
4

(1) When ordering a latch valve, manual override


will be supplied only when specifically requested.
(2) Brass only
(3) For Latch only
(4) Only available in 2/2W - see dimensions details on page 5.2

5.5

None
Plastic

0
1

(1)

Voltage

Orifice
1
1.2
1.6

1
2
3

Wires
1
3
4
5
6
7
B
C
D

two
three

null
a(3)

GEVA-75 Index
Technical Specifications
Max. Pressure

Ports size:

1/8" BSP or NPT

Materials:

Base & manual override:

Function

Orifice

AC

DC

DC latch

2WNC

up to 2.0

12

12

12

16

12

16

1.2

11

11

Reinforced Nylon
Seals:

Pressure bar

3WNC

EPDM

1.6

16

16

16

See solenoid specifications

1.2

12

12

12

Pressure:

See table

1.6

Mounting:

Flange or by two taping screws No.6

Voltage:

12, 24, 110, 230 AC

Solenoid:

3WNO

12, 24 DC
9-12, 24 V Latch
Protection class IP66

Dimensions
59

65

1/8

70

77

22

3W

For taping screw


No. 6

15

2WNC

M6 THRU
TYPx2

37

15

25

15

M5 x0.8 DEEP 8
TYPx2

7.3

20

22
CABLE LENGTH
350 (mm)

30

30
A

Manual
Override

1/8" BSP/NPT
BOTH ENDS

25

1/8" BSP/NPT
BOTH ENDS

1/8" or 1/4"
BSP/NPT
TYPx2

32

48.3

Brass

35.8

Plastic

5.6

SV-11-10

Technical Info

GEVA-75 Index
BACCARA

GALIT Pilot Operated Solenoid Valve


3/2 Way NC, NO
General Description
GALIT Pilot operated 3/2 Way NC, NO
solenoid valves were specially designed
to control medium and large valves.
These valves are controlled by various
options of AC, DC and Latch G75 coils.
Although being compact, the valves enable
large flow pass.

Notes
Minimum pilot pressure of 1 bar is required.

Mounting Bracket

GALIT

Mounting
Bracket

Voltage

Port

Wires

1/8"BSP

10

without

two

1/8"NPT

11

with

three

4
5
6
B
C
D

(1) For latch only

5.7

null
a(1)

GEVA-75 Index
Technical Specifications
Functions:

3/2 Way NC or NO

Ports size:

1/8" BSP or NPT

Orifice:

5mm

Pressure range:

1 - 10 bar

Temperature range:

Ambient : -10 - 50 C
Fluid : 5 - 50

Materials:

Main Valve:
Reinforced Nylon
Seals:
NBR
Solenoid:
See solenoid specifications

Media:

Water

Coil Voltage:

All G75 coil voltages


Protection class IP66

Dimensions
IN
1/8" BSP / NPT

151

AUTO

EX N.O

OPEN

CLOSE

OUT

IN N.C

33

56

IN N.O
EX N.C

5.8

SV-10-09

Technical Info

GEVA-75 Index
BACCARA

GEVA 75 Inline Electric Valve


3/4", 1", 1-1/2", 2" 2/2 Way, NC
General Description
GEVA 75 control valves provide high hydraulic
performances in fluid control.
Both the efficient design and the advanced
technology plastics they are made of, make
the valves strong, with very low maintenance.

Notes
Made of advanced technology plastics,
synthetic elastomers, Stainless steel and
plastics resistant to corrosion.
They work in a wide range of pressures.
Manual override in all the valves with
internal draining.
Progressive opening and shut off that
prevents water hammer.
Very low head loss with high flows.
Easy maintenance. Total access to the
internal parts from the cover of the valve.
Wide range of possibilities such as electric
valves, pressure regulating etc.

Applications
Electric remote control
Farm and gardening irrigation
Advanced computerized irrigation
Level control
Filtration systems
Fertilization systems
Environmental control

How to Order
Example : G75-S-50151
Is a GEVA 75 3/4" BSPT inline electric
hydraulic valve, 2WNC, with flow control,
24V AC.

G75-S

Port
3/4" BSP
3/4" NPT
1" BSPT
1" NPT
1" slip in
1-1/2" BSPT
1-1/2" NPT
2" BSPT
2" NPT

Manual
Override

Function
50
51
60
61
62
70
71
80
81

2WNC

None
Plastic
Handle

Flow control
0
1
2

(1) 3/4, 1, 1-1/2, 2 valves


(2) 3/4, 1 valves
(3) For latch only
(4) Only available in 2/2W - see dimensions details on page 5.2

5.11

with(1)
without(2)

5
6

Voltage
24VAC
12VAC
12VDC
24VDC
24Latch(23)
110VAC (4)
6 Latch (4)
12 Latch (9)
16 Latch (12)

Wires (3)
1
3
4
5
6
7
B
C
D

two
three

null
a

GEVA-75 Index
Technical Specifications
Size:

3/4", 1", 1-1/2 & 2

Connection:

Female BSPT or NPT thread

Head loss for fully open valve

1 PVC - slip in pipe


2

Pressure range: 0.3 - 10Kg/cm


Max.Fluid Temp: 50
Geva 75

1"

Solenoid:

H
(kg/cm2)

3/4
"

0.3 - 10bar (1-1/2-2)

2WNC solenoids, all voltages

RECOMMENDED WORKING ZONE

AC, DC and latch (1 PVC valve)


Materials:

Body & Cover:


Reinforced Nylon
PVC (1 PVC valve)
Spring :
AISI 302
Diaphragm:
PVC
Seals:
Buna - N
Screws:
AISI 304

Q (m3/h)

H
(kg/cm2)

Dimensions
Size

2"

1-1

/2"

Head loss for fully open valve

RECOMMENDED
WORKING ZONE

Weight

3/4"

105 110 105

81

230g

1"

112 110 112

81

230g

1-1/2"

180 160 126 127

740g

2"

190 170 126 127

790g

Q (m3/h)

3/4" & 1"

112

1" PVC slip in

81

127

With flow control


1-1/2" & 2" With Integrated Solenoid

Without flow control

5.12

SV-04-09

GEVA-75 Index
BACCARA

GEVA 75 Inline Hydraulic Valve


3/4", 1", 1-1/2", 2" 2/2 Way, NO
General Description
GEVA 75 control valves provide high hydraulic
performances in fluid control.
Both the efficient design and the advanced
technology plastics they are made of, make
the valves strong, with very low maintenance.

Notes
Made of advanced technology plastics,
synthetic elastomers, Stainless steel and
plastics resistant to corrosion.
They work in a wide range of pressures.
Progressive opening and shut off that
prevents water hammer.
Very low head loss with high flows.
Easy maintenance. Total access to the
internal parts from the cover of the valve.
Wide range of possibilities such as electric
valves, pressure regulating etc.
A "drill" body can be ordered upon special
request.

Applications
Electric remote control
Farm and gardening irrigation
Advanced computerized irrigation
Level control
Filtration systems
Fertilization systems
Environmental control

How to Order
Example : G75-S-5015
Is a GEVA 75 3/4" BSPT inline hydraulic
valve, 2WNC, with flow control.

G75-S

Port
3/4" BSP
3/4" NPT
1" BSPT
1" NPT
1" slip in
1-1/2" BSPT
1-1/2" NPT
2" BSPT
2" NPT

Function
50
51
60
61
62
70
71
80
81

2WNO

Flow control
with
without (1)

5
6

(1) 3/4", 1" valves only

5.13

Technical Info

GEVA-75 Index
Technical Specifications
Size:

3/4", 1", 1-1/2" & 2"

Connection:

Female BSPT or NPT thread

Head loss for fully open valve

1" PVC - slip in pipe


2

Pressure range: 0.3 - 10Kg/cm


0.3 - 10bar

Body & Cover:

1"

Materials:

3/4
"

H
(kg/cm2)

Max.Fluid Temp: 50
Reinforced Nylon

RECOMMENDED WORKING ZONE

PVC (1" PVC valve)


Spring :
AISI 302
Q (m3/h)

Diaphragm:
PVC

Head loss for fully open valve

Seals:
Buna - N
Screws:

H
(kg/cm2)

Dimensions
Size

RECOMMENDED
WORKING ZONE

Weight

3/4"

105 110

77

81

52.5 1/8" NPT/BSP

230g

1"

112 110

84

81

48.5 1/8" NPT/BSP

230g

180 160 998 127

92 1/4" NPT/BSP

740g

190 170

94 1/4" NPT/BSP

790g

1-1/2"
2"

2"

1-1

/2"

AISI 304

98

127

Q (m3/h)

3/4" & 1"

1" PVC slip in

1/8" BSP
Thread

84

(G)

E
127

81

With flow control


1-1/2" & 2" With Integrated Solenoid

Thread
(G)
A

Without flow control

5.14

Thread
(G)

SV-10-09

Technical Info

GEVA-75 Index
BACCARA

GEVA 75 Pilot Operated


3/8", 1/2" 2/2 Way NC
General Description
GEVA 75 Pilot operated 2/2 Way NC
solenoid valves are recommended for
applications where high flow at high
pressure is required. They can be used
in control and automation systems
The typical applications are:
industrial furnace, heating equipment,
burners, oil and gas, autoclaves, dental
equipment, instrumentation, car washers,
machine industries and irrigation.

Notes
The working pressure is 12 bar.
A minimum pressure of 0.5 bar
is required for operation.
To order valves manufactured to your
specific requirements, please contact
our technical sales department.

How to Order
Example : G75-S-4401N-1
Is a GEVA 75 Pilot operated 1/2" BSP,
2WNC, NBR seals, 24V AC.

G75-S

Body
Nylon

Port
4

3/8"BSP
3/8"NPT
1/2"BSP
1/2"NPT

Function
30
31
40
41

2WNC

Seals
1

(1) For latch only


(2) Only available in 2/2W - see dimensions details on page 5.2

5.15

NBR
EPDM

Wires(1)

Voltage
N
E

1
2
3
4
5
6
7
B
C
D

two
three

null
a

GEVA-75 Index
Technical Specifications
Functions:

2/2 Way NC

Ports size:

3/8", 1/2" BSP or NPT

Orifice:

12mm

Pressure and flow:

0.5 -12 bar Kv 35 L/min

Temperature range:

Fluid : max 80 C
Ambient : -10 C to 50 C

Solenoid:

Geva 75
2WNC solenoids, all voltages

Materials:

Body & cover:


Reinforced Nylon
Spring:
AISI 302
Diaphragm:
NBR, EPDM
Seals:
NBR, EPDM
Screws:
AISI 304
Protection class IP65

Dimensions

5.16

SV-04-09

Technical Info

GEVA-75 Index
BACCARA

GEVA 75 Manifold Installation


General Description
The GEVA 75 manifold installation provides a
turn-key solution.
Available with various types of GEVA 75
solenoids, functions and voltages.

Pilot Operated

G75

How to Order
Example : G75-M-541031
Is a 5 station Geva 75 manifold 3W NO,1/8"BSP,
direct operating 1.6 orifice, 24V AC solenoids.
GEM-SOL

G75-M

#
stations

Type
G75
1
GEM-SOL 2
Pilot Op.
3

3
4
5
6
7
8
9
10
11
12

3
4
5
6
7
8
9
10
11
12

Function
without
sol
2WNC
3WNC
3WNO
Pilot (1)
operated NC
Pilot (1)
operated NO

Orifice (2)

Port
0

1/8"BSP
1/8"NPT

1
3
4
5
6

(1) Only available for Pilot Operated


(2) GEM-SOL orifices are :
3/2 Way NO - 1.6
3/2 Way NO - 2.4
G75 orifices are :
3/2 Way NO/NC - 1.2
(3) For Latch only
(4) Only available in 2/2W - see dimensions details on page 5.2.
Please consult with our technical sales department.

5.17

10
11

1
1.2
1.6
Pilot operated(1)

Wires (3)

Voltage
1
2
3
5

1
3
4
5
6
7
B
C
D

two
three

null
a

GEVA-75 Index
Technical Specifications
Direct Operated

Hose Nipple
Tube

Hose Nipple
Tube

Pilot Operated

#
stations

10

11

12

261

348

435

522

609

696

783

870

957

1044

130.5

174

217.7

261

304.5

348

391.5

435

478.5

522

5.18

SV-04-09

Technical Info

GEVA-75 Index
BACCARA

GEVA 75 Irrigation Controllers


General Description
Stand-alone battery driven irrigation controller
timer with a G75 2WNC 9VDC latch coil
connected. Powered by a single 9V battery.
Can operate any valve equipped with
R
3/4" UNEF solenoid cavity (Richdel type).

Notes
Dust and water tight.
Various mounting options, on valve and wall.
High quality alkaline battery included.
Three automatic irrigation controllers, plus
manual operation.
Please consult our technical sales department
for further information on compatibility with
various coils.
Options:
Solar Panel

How to Order Table


1)Example : G75-C-2-50-60

G75 One Valve

G75 Two Valves

Is a Geva 75 Two Valves controller :


Valve 1 : 3/4" BSP, Valve 2 : 1" BSP

2) Example : G75-C-4-60-50-70-80-00
Is a Geva 75 Four Valves controller :
Master Valve : 1" BSP, Valve 1 : 3/4" BSP, Valve 2 : 1-1/2" BSP,
Valve 3 : 2" BSP, Valve 4 : No Valve

3) Example : G75-C-2-60-G75-A-110102
Is a Geva 75 Two Valves controller :
Valve 1 : 1" BSP
Valve 2 : G-75-A with flange, 1/8"BSP, 2WNC, No manual override, 1.2 orifice

G75-C

Type of
Controller
One Valve
Two Valves
Four Valves

1
2
4

Valve

Valve
No valve
1/2"BSP
1/2"NPT
3/4"BSP
1"BSP
1" NPT
1-1/2" BSP
1-1/2" NPT
2" BSP
2" NPT

00
40
41
50
60
61
70
71
80
81

G75-A *

No valve
1/2"BSP
1/2"NPT
3/4"BSP
1"BSP
1" NPT
1-1/2" BSP
1-1/2" NPT
2" BSP
2" NPT

Valve
No valve
1/2"BSP
1/2"NPT
3/4"BSP
1"BSP
1" NPT
1-1/2" BSP
1-1/2" NPT
2" BSP
2" NPT

00
40
41
50
60
61
70
71
80
81

G75-A *

Valve
00
40
41
50
60
61
70
71
80
81

G75-A *

G75-A *

* G75-A
Type
with flange
1
without flange 2
Brass
3

Port
1/8" BSP
1/4" BSP (1)
1/8" NPT
1/4" NPT (1)

Manual
Override
-

Function
10
20
11
21

2WNC
3WNC
3WNO

1
3
4

Orifice
1
1.2
1.6

No valve
1/2"BSP
1/2"NPT
3/4"BSP
1"BSP
1" NPT
1-1/2" BSP
1-1/2" NPT
2" BSP
2" NPT

1
2
3

(1) BRASS only

5.19

G75 Four Valves

Valve
00
40
41
50
60
61
70
71
80
81

No valve
1/2"BSP
1/2"NPT
3/4"BSP
1"BSP
1" NPT
1-1/2" BSP
1-1/2" NPT
2" BSP
2" NPT
G75-A *

00
40
41
50
60
61
70
71
80
81

GEVA-75 Index
Technical Specifications
Mechanical

Electrical

Software

Mounting Options

Option

Wall Mounting

One Valve

Vertical Mounting

Horizontal Mounting

Two Valves

Four Valves

Once daily, at the


same time

Up to three starts
per day

Up to three starts
per day

Once daily, on
selected days

Starts select

Starts select

Day select

Day select

Season adjustment
10% - 200%

Season adjustment
10% - 200%

Off

Off

Three starts per


day

Solar Panel

Off

Master Valve will be


opened for each
command

5.20

SV-10-09

Technical Info

GEVA-75 Index
BACCARA

GEVA 75 Irrigation Window Controllers


General Description
Stand-alone battery driven irrigation controller
timer with a G75 2WNC 9VDC latch coil
connected. Powered by a single 9V battery.
Can operate any valve equipped with
R
3/4" UNEF solenoid cavity (Richdel type).
G75 Window

Notes
Dust and water tight.
Various mounting options, on valve and wall.
High quality alkaline battery included.
Three automatic irrigation controllers, plus
manual operation.
Please consult our technical sales department
for further information on compatibility with
various coils.
Options:
Solar Panel

G75 Window+

How to Order Table: G75 Window


Example : G75-C-1W-50

How to Order Table: G75 Window+


Example : G75-C-1W+-GEM-A-21045N0

Is a Geva 75 Window controller with 3/4BSP valve.

Is a Geva 75 Window+ controller with :


GEM-A brass valve, 1/8" BSP, 3WNO, 2.4 orifice,
NBR, no manual override.

G75-C-1W

Valve
No valve
3/4"BSP
1"BSP
1" NPT
1-1/2" BSP
1-1/2" NPT
2" BSP
2" NPT

00
50
60
61
70
71
80
81

G75-C-1W+

Refer to How to Order


Section of GEM-SOL
valves.
Consult with us to
discuss your specific
requirements.

G75-A *

This controller will only operate with G75 operators.

* G75-A
Type

Port

10
with flange
1 1/8" BSP
(1) 20
without flange 2 1/4" BSP
11
Brass
3 1/8" NPT
1/4" NPT (1) 21

Valve

Manual
Override

Function
2WNC
3WNC
3WNO

1
3
4

Orifice
1
1.2
1.6

1
2
3

(1) BRASS only

5.21

GEVA-75 Index
Technical Specifications
Mechanical

Electrical

Software

Mounting Options

Option

Wall Mounting

Vertical Mounting

Horizontal Mounting

Solar Panel

Window +

Window
Set start and end
hours

Set start and end


hours

Set On time (1
second to 12 hours)

Set On time (1
second to 12 hours)

Set Off time (1 min


to 12 hours)

Set Off time (1 min


to 12 hours)

Day select

Day select

Off

Off
High-powered

5.22

SV-04-09

Technical Info

GEVA-75 Index
BACCARA

GEVA 75 Multi-Zone DC & AC Irrigation Controller


General Description
The Geva 75 multi-zone DC irrigation controller is a new
generation of irrigation controllers, with a user friendly menu
driven interactive software. It is a stand alone battery power
driven 4 to 8 zones irrigation controller. Powered by a single
9V battery. Enables to operate G75 9V latch coils or equivalent
Geva 75 multi-zone AC is a 24V AC , 4 to 8 zones irrigation
controller with an integrated backup battery.
Also enables to operate G75 9V latch coils or equivalent.

Notes
For indoor or outdoor use.
High quality alkaline battery included.
Large graphics LCD provides easy reading.
Menu driven interactive software.
Built-in multi-lingual menu: English, Spanish, Italian,
French, Portuguese and Hebrew.
Weekly or daily scheduled programming.
Two factory preset programs included.
Master valve output, manual irrigation, system
test procedure and rain sensor input included.

How to Order
Example : G75-C-81
Is a Geva 75 8 zones DC irrigation controller.

G75-C

Type
8 zones

Voltage
8

9V DC
24V AC*

1
2

* AC controller

Adaptor for outdoors

Adaptor for indoors

5.23

GEVA-75 Index
Technical Specifications
Mechanical specifications

Software features
Scheduling timer options:
Program A: 7 day weekly day schedule
Program B: Days, interval scheduling
Program C: Factory preset 7 day weekly
schedule
Program D: Factory preset days, interval
scheduling.
Unit off.
Manual operation.
System analysis:
Sequential operation of the valves.
Up to four starts per valve per day. Valves
will then open in sequence.
Irrigation duration in minutes and hours
(1 min -12 hrs with 10 min default).
Season adjustment for irrigation duration
10% - 200% in 10% increments.
Rain sensor ON/OFF option.
Real time weekly clock (D:HH:MM).
User menu language selection.

Mounting : Indoor or outdoor, wall mount or 3/4"


to 2" pipe mount (horizontal or vertical).
Dust and water tight; electronic enclosure
equivalent to IP67. Terminal and battery
compartment equivalent to IP65.
Operating temperature: - 10 to 60 C
Six keys keypad.
Electrical specifications
Integrated Lithium memory backup battery.
Screw in terminals.
Low battery indicator.
Power saving LCD display.
Waterproof
AC:
Power supply : 230/50 to 24/50V AC 20VA
830 mA transformer or 115/60 to 24/60V
830 mA transformer.
DC:
Power supply : One 9V alkaline battery. Use
top quality to ensure one year independent
operation.

Dimensions

5.24

SV-04-09

GEVA-75 Index
BACCARA

GEVA 75 Inline Hydraulic Valve


3/4", 1", 1-1/2", 2" Line pilot
General Description
GEVA 75 control valves, 3/4", 1", 1-1/2" and 2" provide
high hydraulic performances in fluid control.
Both the efficient design and the sophisticated plastics
they are made of, make the GEVA 75 valves strong,
with very low maintenance.

Notes
Supplied with solenoid but without accessories.

Applications
Electric remote control
Farm and gardening irrigation
Advanced computerized irrigation
Level control
Filtration systems
Fertilization systems
Environmental control

How to Order
Example : G75-S-704H51
Is a GEVA 75 1-1/2"BSP inline hydraulic valve,
2WNC with flow control, with 3WNO solenoid,
24V AC

G75-S

Port
3/4"BSP
3/4"NPT
1"BSP
1"NPT
1-1/2"BSP
1-1/2"NPT
2" BSP
2" NPT

Function
50
51
60
61
70
71
80
81

3WNO

4H

Flow control
with

(1) When ordering a latch valve, manual override


will be supplied only when specifically requested.
(2) For latch only.

SV-04-09

5.25

Wires(1)

Voltage
1
3
4
5
6
7
B
C
D

two
three

null
a(2)

GEVA-75 Index
BACCARA

GEVA 75 Inline Hydraulic Valve


1-1/2", 2" External pilot 3W
General Description
GEVA 75 control valves, 1-1/2" and 2" provide high
hydraulic performances in fluid control.
Both the efficient design and the sophisticated plastics
they are made of, make the GEVA 75 valves strong,
with very low maintenance.

Notes
Pilot pressure should be higher than line pressure.

Applications
Electric remote control
Farm and gardening irrigation
Advanced computerized irrigation
Level control
Filtration systems
Fertilization systems
Environmental control
Low pressure
For contaminated water

How to Order
Example : G75-S-70451
Is a GEVA 75 1-1/2"BSP inline hydraulic valve,
2WNC with flow control, with 3WNO, 24V AC solenoid.

G75-S

Port
1-1/2"BSP
1-1/2"NPT
2" BSP
2" NPT

Function
70
71
80
81

3WNC

Flow control
4

with

(1) When ordering a latch valve, manual override


will be supplied only when specifically requested.

Wires(1)

Voltage
1
3
4
5
6
B
C
D

two
three

null
a (2)

(2) For latch only.

5.26

SV-04-09

GEVA-75 Index
BACCARA

GEVA 75 Inline Hydraulic Valve


1-1/2", 2" Level float valve
General Description
GEVA 75 control valves, 1-1/2" and 2" provide high
hydraulic performances in fluid control.
Both the efficient design and the sophisticated plastics
they are made of, make the GEVA 75 valves strong,
with very low maintenance.

Applications
Electric remote control
Farm and gardening irrigation
Advanced computerized irrigation
Level control
Filtration systems
Fertilization systems
Environmental control

Solenoid and accessories for demonstration only

How to Order
Example : G75-S-70150
Is a GEVA 75 1-1/2"BSP inline hydraulic valve,
2WNC with flow control.

G75-L

Port
1-1/2"BSP
1-1/2"NPT
2" BSP
2" NPT

SV-04-09

Function
70
71
80
81

2WNC

Flow control
1

with

5.27

Voltage
No coil
hydraulic

GEVA-75 Index
BACCARA

GEVA 75 Inline Hydraulic Valve 1-1/2", 2"


Level float valve with shut off solenoid
General Description
GEVA 75 control valves, 1-1/2" and 2" provide high
hydraulic performances in fluid control.
Both the efficient design and the sophisticated plastics
they are made of, make the GEVA 75 valves strong,
with very low maintenance.

Applications
Electric remote control
Farm and gardening irrigation
Advanced computerized irrigation
Level control
Filtration systems
Fertilization systems
Environmental control

How to Order
Example : G75-S-70150
Is a GEVA 75 1-1/2"BSP inline hydraulic valve,
2WNC with flow control.

G75-L

Port
1-1/2"BSP
1-1/2"NPT
2" BSP
2" NPT

Function
70
71
80
81

2WNC

Flow control
1

with

(1) When ordering a latch valve, manual override


will be supplied only when specifically requested.

Wires(1)

Voltage
1
3
4
5
6
B
C
D

two
three

null
a (2)

(2) For latch only.

5.28

SV-04-09

GEVA-75 Index
BACCARA

GEVA 75 Inline Hydraulic NC Valve


1-1/2", 2" External solenoid 3W NO
General Description
GEVA 75 control valves, 1-1/2" and 2" provide high
hydraulic performances in fluid control.
Both the efficient design and the sophisticated plastics
they are made of, make the GEVA 75 valves strong,
with very low maintenance.

Solenoid and accessories for demonstration only

Applications
Electric remote control
Farm and gardening irrigation
Advanced computerized irrigation
Level control
Filtration systems
Fertilization systems
Environmental control

How to Order
Example : G75-S-70150
Is a GEVA 75 1-1/2"BSP inline hydraulic valve,
2WNC with flow control.

G75-S

Port
1-1/2"BSP
1-1/2"NPT
2" BSP
2" NPT

Function
70
71
80
81

2WNC

Flow control
1

with

(1) When ordering a latch valve, manual override


will be supplied only when specifically requested.
(2) For latch only.

SV-04-09

5.29

Wires (1)

Voltage
1
3
4
5
6
B
C
D

two
three

null
a(2)

GEVA-75 Index
BACCARA

GEVA 75 Inline Hydraulic NO Valve


1-1/2", 2" External solenoid 3W NC
General Description
GEVA 75 control valves, 1-1/2" and 2" provide high
hydraulic performances in fluid control.
Both the efficient design and the sophisticated plastics
they are made of, make the GEVA 75 valves strong,
with very low maintenance.

Notes
The valve is identical to 2W NC valve,
2W NO function is a result of the solenoid.
Solenoid and accessories for demonstration only

Applications
Electric remote control
Farm and gardening irrigation
Advanced computerized irrigation
Level control
Filtration systems
Fertilization systems
Environmental control

How to Order
Example : G75-S-70250
Is a GEVA 75 1-1/2"BSP inline hydraulic valve,
2WNO with flow control.

G75-S

Port
1-1/2"BSP
1-1/2"NPT
2" BSP
2" NPT

Function
70
71
80
81

2WNO

Flow control
2

with

(1) When ordering a latch valve, manual override


will be supplied only when specifically requested.

Wires(1)

Voltage
1
3
4
5
6
B
C
D

two
three

null
a (2)

(2) For latch only.

5.30

SV-04-09

GEVA-75 Index
BACCARA

GEVA 75 Inline Hydraulic NC Valve


3/4",1",1-1/2", 2" Manual selector
General Description
GEVA 75 control valves, 3/4", 1", 1-1/2" and 2" provide high
hydraulic performances in fluid control.
Both the efficient design and the sophisticated
plastics they are made of, make the GEVA 75
valves strong, with very low maintenance.

Applications
Electric remote control
Farm and gardening irrigation
Advanced computerized irrigation
Level control
Filtration systems
Fertilization systems
Environmental control

How to Order
Example : G75-SM-70150
Is a GEVA 75 1-1/2"BSP inline hydraulic
valve 2WNC with flow control and a
manual selector.

G75-SM

Port
3/4"BSPT
3/4"NPT
1"BSPT
1"NPT
1-1/2"BSPT
1-1/2"NPT
2" BSPT
2" NPT

SV-04-09

Function
50
51
60
61
70
71
80
81

2WNC

Flow control
1

with

Voltage
No coil
hydraulic

5.31

GEVA-75 Index
BACCARA

GEVA 75 Inline Hydraulic NC Valve 1-1/2", 2"


External solenoid 3W NO and a Manual selector
General Description
GEVA 75 control valves, 1-1/2" and 2" provide high
hydraulic performances in fluid control.
Both the efficient design and the sophisticated
plastics they are made of, make the GEVA 75
valves strong, with very low maintenance.

Applications
Electric remote control
Farm and gardening irrigation
Advanced computerized irrigation
Level control
Filtration systems
Fertilization systems
Environmental control

How to Order
Example : G75-SM-70150
Is a GEVA 75 1-1/2"BSP inline hydraulic
valve 2WNC with flow control and a
manual selector.

G75-SM

Port
1-1/2"BSPT
1-1/2"NPT
2" BSPT
2" NPT

Function
70
71
80
81

2WNC

Flow control
1

with

Voltage
No coil
hydraulic

5.32

SV-04-09

GEVA-75 Index
BACCARA

GEVA 75 Inline Hydraulic NC Valve


3/4", 1", 1-1/2", 2" Pressure relief
General Description
GEVA 75 control valves, 3/4",1",1-1/2" and 2" provide
high hydraulic performances in fluid control.
Both the efficient design and the sophisticated
plastics they are made of, make the GEVA 75
valves strong, with very low maintenance.

Applications
Electric remote control
Farm and gardening irrigation
Advanced computerized irrigation
Level control
Filtration systems
Fertilization systems
Environmental control

How to Order
Example : G75-SR-701503
Is a GEVA 75 1-1/2"BSP inline hydraulic
valve 2WNC with flow control set to 3-6 bar.

G75-SR

Port
3/4" BSPT
3/4" NPT
1" BSPT
1" NPT
1-1/2" BSPT
1-1/2" NPT
2" BSPT
2" NPT

SV-04-09

Function
50
51
60
61
70
71
80
81

2WNC

Flow control
1

with
without

5
6

Set pressure
(bar)

Voltage
No coil
hydraulic

5.33

1-3
2-5
3-6
4-7

1
2
3
4

GEVA-75 Index
BACCARA

GEVA 75 Inline Valve 1-1/2", 2" Electrical and


Hydraulic pressure reducing
General Description
GEVA 75 control valves, 1-1/2" and 2" provide high
hydraulic performances in fluid control.
These valves, together with the XR100 3 way pressure
reducing, provide compact, efficient and accurate
high flow pressure reducers.

Notes
Supplied assembled with a solenoid and accessories.
A finger filter has been installed at the pilot pressure
supply. Clean when necessary.
The XR100 has a three positions manual override:
AUTO: for automatic operation (valve is open when
solenoid is energized)
MANUAL: valve is kept open
CLOSE: valve is kept closed.
Pilot pressure must be equal or higher to line
pressure.

How to Order

Port

G75-PR

Function

Flow control

Voltage

Example : G75-PR-70151
Is a GEVA 75 1-1/2"BSP electric
pressure reducing valve 2WNC with
flow control, with a 24 VAC solenoid.

1-1/2"BSPT
1-1/2"NPT
2" BSPT
2" NPT

5.34

70
71
80
81

2WNC

with

without
24V AC
9-12VDC Latch
12V AC
12V DC
24V DC

0
1
2
3
4
5

SV-04-09

GEVA-75 Index
BACCARA

GEVA 75 Inline Valve 1" Electrical and Hydraulic


pressure reducing
General Description
GEVA 75 1" control valves provide high hydraulic
performances in fluid control.
These valves, together with the XR100 3 way pressure
reducing, provide compact, efficient and accurate
high flow pressure reducers.

Notes
Supplied assembled with a solenoid and accessories.
A finger filter has been installed at the pilot pressure
supply. Clean when necessary.
The XR100 has a three positions manual override:
AUTO: for automatic operation (valve is open when
solenoid is energized)
MANUAL: valve is kept open
CLOSE: valve is kept closed.
A minimum pressure differential of 1 bar is required.

How to Order

Port

G75-PR

Function

Flow control

Voltage

Example : G75-PR-60161
Is a GEVA 75 1" BSP electric
pressure reducing valve 2WNC without
flow control, with a 24 VAC solenoid.

SV-04-09

1"BSPT
1"NPT

5.35

60
61

2WNC

without

without
24V AC
9-12VDC Latch
12V AC
12V DC
24V DC

0
1
2
3
4
5

5.36

GEVA-75 Index
BACCARA

GEVA 75 Inline Hydraulic Valves 3/4", 1",


1-1/2 ", 2" 2/2 Way NC, Zero pressure
General Description
GEVA 75 control valves 3/4" - 2" provide high hydraulic
performances in fluid control.
Both the efficient design and the advanced technology
plastics they are made of, make the valves strong,
with very low maintenance.

Notes
Made from synthetic elastomers, Stainless steel
and plastics resistant to corrosion.
They work in a wide range of pressures.
Manual override in all the valves with internal
draining.
Minimum pilot pressure 1.5 bar above line
pressure.
Very low head loss with high flows.
Easy maintenance. Total access to the internal
parts from the cover of the valve.

Applications
Electric remote control
Drain systems
Close systems

How to Order
Example : G75-Z-60151
Is a GEVA 75 1" BSP inline electric valve, 2WNC
with flow control, 24V AC for zero differential pressure.
Function

Port

G75-Z

3/4"BSPT
3/4"NPT
1" BSPT
1" NPT
1-1/2" BSPT
1-1/2" NPT
2" BSPT
2" NPT

50
51
60
61
70
71
80
81

2WNC

Flow control
with
without (1)

5
6

(1) 3/4", 1" valves only

5.37

Technical Info

GEVA-75 Index
Technical Specifications
Size:

3/4", 1", 1-1/2", 2"

Connection:

Female BSPT

Head loss for fully open valve

or NPT thread
Line: 0-6 bar

50C

Materials:

Body & Cover:

H
(kg/cm2)

2"

above line pressure


Max.Fluid Temp:

1-1
/2"

Pilot: 1.5 bar

1"

3/4
"

Pressure range:

RECOMMENDED
WORKING ZONE

Reinforced Nylon
Spring :
AISI 302
Q (m3/h)

Diaphragm:
PVC
Seals:
Buna - N
Screws:

Dimensions

AISI 304

Size

Weight

3/4"

117 110

81

230g

1"

124 110

81

230g

1-1/2"

180 160 126 740g

2"

190 170 126 740g

With flow control

Without flow control

5.38

SV-04-09

Technical Info

GEVA-75 Index
BACCARA

Digital Differential Pressure Gauge Switch (D.D.P.G.S.)


General Description
The Baccara Digital Differential Pressure Gauge Switch
combines a gauge and a switch in one unit, which allows
the user to program a wide range of monitoring and
switching parameters to suit specific applications.
It is specially designed for filter flushing systems.
With its LCD display, user friendly interface for
setting the working parameters and the IP66
environmental protection, this unit gives a reliable
and easy to use solution for automatic filters.
With the aid of the latch solenoid driver it is
possible to upgrade a simple manual filter
to an automatic one.

Note
See instruction manual for further information
H pressure must be higher than L pressure.
Maximum H pressure 200 psi/14 bar.
This unit can be used as a manometer up to
99 psi or 7 bar.
Please consult our technical sales department
for special applications.

How to Order

Example: G75-DP-1BD
Is a digital differential pressure gauge switch
with a mounting bracket and a solenoid
driver.

G75-DP

Type
Stand
alone

Accessories
1

Mounting
Bracket
Latch Solenoid
Driver

B
D

5.39

GEVA-75 Index
Technical Specifications
Mechanical specifications

Disconnect low pressure before high pressure


Connect the tubes from the unit so that
they point downwards

Programmable Settings
Manual Operation
PSI or BAR display
Time interval between pressure
measurements
Electrical specifications

Contact closed time

Power supply 9 - 24 VDC or 12-24VAC

Time interval between contact closure

Low power detect

Zero calibration

Dry contact (N.O.) 0.5A at 24VAC


Internal memory to retain Set-up Data

Display

at power down.

The LCD display shows the actual Differential


Pressure (DIF) and the pressure differential

Mounting

trigger setting (SET) continuously when power

2 ft/60 cm cable + 4 wires

is connected. When the switch contacts are

RED + BLK - power supply

closed, this is indicated by displaying On.

GRN / WHT N.O. contact


Pressure ports 1/8 BSP/NPT (male)

Display resolution:

High pressure port is marked by the letter "H"

1 PSI in the range 0-99psi.

on the housing

0.1 BAR in the range 0.0-7.0 BAR.

Connect high pressure before low pressure

Dimensions

43

60

57.7

41

1/8 BSP
TYPX2

89.5

M5
TYPX2

25

.8

58.8
(60)

5.40

SV-04-09

Technical Info

GEVA-75 Index
BACCARA

GEVA 75 Long Distance Operator (LDO)


2/2, 3/2 Way NC, NO
General Description
The Long Distance Operator makes it possible
to activate a solenoid valve by using a small
section conductor at a distance of up to 5 km
from the voltage source.
The valves' main advantage is the reduction
in conduit cost.
Allows use of a lower power source.
The device is supplied with G75 2/2 or 3/2 Way
NC, NO solenoid valve.
Specially suited for irrigation control.

Notes
This solenoid is designed to operate only
with a Baccara valve.
To order valves manufactured to your specific
requirements, please contact our technical sales
department

How to Order
Example : G75-LDO-11021
Is a Geva 75 LDO 2WNC, 1/8"BSP, 1.2mm orifice,
24V AC Long Distance Operator.

G75-LDO

Function
2WNC
3WNC
3WNO

Port
1
3
4

None
1/8"BSP
1/8"NPT

Orifice
00
10
11

None(for 2W)
1
1.2
1.6

Voltage
0
1
2
3

24V AC &
12-24 V DC

5.41

GEVA-75 Index
Technical Specifications
Voltage:

12 - 24V DC or 24V AC

Current:

Holding 4 mA

Power:

12V - 50mW

Working Pressure 2W NC
Orifice
Pressure (bar)

24V - 100mW
Protection:

IP67

Ambient Temp:

Max 60 C

Weight :

80 gm

Lead Connection 28cm:

up to 2.0
12

Working Pressure 3W NC
Orifice

1.0

1.2

1.6

Pressure (bar)

16

11

Red / Black - power supply


Green / Black - coil

Materials

Working Pressure 3W NO

Housing:

PP

Encapsulate:

Epoxy

Voltage

Conduit
Distance
section (mm2)
(km)

Orifice

1.0

1.2

1.6

Pressure (bar)

16

12

Delay Time (sec)


On
Off

12 / 24

0.5

12

0.5

12

24

0.5

Dimensions

79

83

50

87

63.2

94

38.5

50.5

2W

3W

5.42

SV-04-09

Main Contents

Technical Info

GC Pressure Operated Valves Index


BACCARA

Globe Cylinder Operated


1/4", 3/8", 1/2", 3/4", 1" 2/2 Way NC
General Description
GC Globe Cylinder operated 2/2 way NC valves are
recommended for applications where high flow is required.
They can be used in control and automation systems at
vacuum or pressure.Typical applications are irrigation
and industrial air, water and vacuum systems.

Notes
Minimum pilot pressure 3 bar.
See graph of pilot pressure vs. line pressure.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

Pilot
Pressure

How to Order
Example : GC-2160-1N
Is a GC Globe cylinder with brass body,
1" BSP 2WNC with NBR seals.

GC

Body
Brass
St.st

Flow
under seat

Type
2
3

Globe

Port
1

1/4" BSP
1/4" NPT
3/8" BSP
3/8" NPT
1/2" BSP
1/2" NPT
3/4"BSP
3/4"NPT
1" BSP
1" NPT

Function
20
21
30
31
40
41
50
51
60
61

6.1

2W NC
2W NC
bidirectional

Seals
1
1a

NBR / PU
EPDM
Viton
PTFE

N
E
V
T

Flow
above seat

GC Pressure Operated Valves Index


Technical Specifications
Functions:

2/2 Way NC

Ports size:

1/4", 3/8", 1/2", 3/4", 1" BSP & NPT

Pressure and flow:

See table

Temperature range:

Fluid: 60 C

Line Pressure

1/4"

Vacuum-10 Bar

3/8", 1/2"

12

Vacuum-10 Bar

3/4"

20

Vacuum-10 Bar

1"

25

Vacuum-10 Bar

Ambient: -10 C to 50 C
Materials in contact
Main valve :
Brass, St.st 316

Seals:

NBR / PU, Viton, EPDM and PTFE

Pilot pressure

with fluid :

Orifice
(mm)

Size

1"

3/4"
1/4"

1/2"

2
1
0
-1

10

10

Line pressure
Flow above seat

12

1/4" BSP

62

58

50

32

23

1/8"BSP

3/8",1/2"BSP

78

69

65

38

27

1/8"BSP

3/4"BSP

86

89

69

55

34

1/8"BSP

1"BSP

110

100

89

65

36

1/8"BSP

Pilot pressure

10
8
6
4

1/4" - 1"

2
0
-1

Line pressure
Flow under seat

Dimensions

E
C

6.2

SV-04-09

Technical Info

GC Pressure Operated Valves Index


BACCARA

Globe Cylinder Operated Stackable Manifold


1/4", 3/8", 1/2", 3/4", 1" 2/2 Way NC/NO
General Description
GC Globe Cylinder operated stackable manifold 2/2 way
NC/NO valves are recommended for applications where high
flow is required. They can be used in control and automation
systems at vacuum or pressure.
Typical applications are irrigation and industrial air, water an
vacuum systems.

Notes
Minimum pilot pressure 3 bar.
See graph of pilot pressure vs. line pressure.
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

outlets

NC

NO

How to Order
Example : GC-SM-02260-1N
Is a GC Globe cylinder operated stackable,
2 station, brass body, 1" BSP, 2WNC, NBR seals. with brass
body, 1" BSP 2WNC with NBR seals.

GC-SM

No.of
stations
specify quantity

Body
Brass
St.st

Port
2
3

1/4" BSP
1/4" NPT
3/8" BSP
3/8" NPT
1/2" BSP
1/2" NPT
3/4"BSP
3/4"NPT
1" BSP
1" NPT

Function
20
21
30
31
40
41
50
51
60
61

6.3

2W NC
2W NC
bidirectional
2W NO

1
1a
2

Seals
NBR
EPDM
Viton

N
E
V

GC Pressure Operated Valves Index


Technical Specifications
Functions:

2/2 Way NC/NO

Ports size:

1/4", 3/8", 1/2", 3/4", 1" BSP & NPT

Pressure and flow:

See table

Temperature range:

Fluid: 60 C

Line Pressure

1/4"

Vacuum-10 Bar

3/8", 1/2"

12

Vacuum-10 Bar

3/4"

20

Vacuum-10 Bar

1"

25

Vacuum-10 Bar

Ambient: -10 C to 50 C
Materials in contact
with fluid :

Orifice
(mm)

Size

Main valve :
Brass, St.st 316

Seals:

Pilot pressure

NBR, Viton, EPDM

1"

3/4"
1/4"

1/2"

2
1
0
-1

1/4" BSP

62

58

50

32

23 1/8"BSP

3/8",1/2"BSP

78

69

65

38

27 1/8"BSP

12

86

89

69

55

34 1/8"BSP

10

110 100

89

65

36 1/8"BSP

1"BSP

10

10

Line pressure
Flow above seat

Pilot pressure

3/4"BSP

8
6
4

1/4" - 1"

2
0
-1

Line pressure
Flow under seat

Dimensions
A
27+40xN

M6 TYPx4
DEEP 12

13.5+40xN

40

N - Number of stations

1/8 BSP

7.5

1/2 BSP

28

13

19.4

43.9

1/2 BSP
TYP x N

10

63.75

6.4

17

40
A

SV-04-09

Technical Info

GC Pressure Operated Valves Index


BACCARA

Globe Cylinder Operated 3/8", 1/2", 3/4", 1"


2/2 Way NC for Steam
General Description
GC Globe Cylinder operated 2/2 way NC valves are recommended
for applications where high flow is required. They can be used
in control and automation systems at vacuum or pressure.
Typical applications are irrigation and industrial air, water an
vacuum systems.

Notes
Minimum pilot pressure 3 bar.
See graph of pilot pressure vs. line pressure.
Stainless steel valves are available only in 3/8"
and 1/2".
To order valves manufactured to your specific
requirements, please contact our technical
sales department.

How to Order
Example : GC-2160-1T
Is a GC Globe cylinder with brass
body, 1" BSP 2WNC with PTFE seals.

GC

Body
Brass
St.st

Type
2
3

Globe

Port
1

3/8" BSP
3/8" NPT
1/2" BSP
1/2" NPT
3/4"BSP
3/4"NPT
1" BSP
1" NPT

Function
30
31
40
41
50
51
60
61

6.5

2W NC

Seals
1

PTFE

GC Pressure Operated Valves Index


Technical Specifications
Functions:

2/2 Way NC

Ports size:

3/8", 1/2", 3/4", 1" BSP & NPT

Pressure and flow:

See table

Temperature range:

Fluid: 150 C

Line Pressure

3/8", 1/2"

27

Vacuum-10 Bar

3/4"

20

Vacuum-10 Bar

1"

25

Vacuum-10 Bar

Ambient: -10 C to 50 C
Materials in contact
with fluid :

Orifice
(mm)

Size

Main valve :
Brass, St.st 316

12

PTFE

10

Pilot pressure

Diaphragm:

8
6
4
2
0
-1

10

Line pressure
Size

3/8",1/2"

69

38

78

64.5

26.5

27

22

3/8",1/2"

1/8"

3/4"

90

55

85.5

68.5

33.5

33

3/4"

1/8"

1"

100

65

110

89

36

40

1"

1/8"

Dimensions

6.6

SV-04-09

Technical Info

GC Pressure Operated Valves Index


BACCARA

Globe Cylinder Operated


3/4", 1", 1-1/2", 2" 2/2 Way NC
General Description
GC Globe Cylinder operated 2/2 way NC valves are recommended
for applications where high flow is required. They can be used
in control and automation systems at vacuum or pressure.
Typical applications are irrigation and industrial air, water an
vacuum systems.

Notes
Minimum pilot pressure 3 bar.
See graph of pilot pressure vs. line pressure.
To order valves manufactured to your specific requirements,
please contact our technical sales department.

How to Order
Example : GC-4160-1N
Is a GC Globe cylinder with nylon
body, 1" BSP 2WNC with NBR seals.

GC

Body
Nylon

Type
4

Globe

Port
1

3/4" BSP
3/4" NPT
1" BSP
1" NPT
1-1/2"BSP
1-1/2"NPT
2" BSP
2" NPT

Function
50
51
60
61
70
71
80
81

6.7

2W NC

Seals
1

NBR
EPDM
Viton
Polyurethane

N
E
V
P

GC Pressure Operated Valves Index


Technical Specifications
Functions:

2/2 Way NC

Ports size:

3/4", 1", 1-1/2", 2" BSP & NPT

Pressure and flow:

See table

3/4", 1"

27

Vacuum-10 Bar

Temperature range:

Fluid: max 60 C

1-1/2, 2"

55

Vacuum-10 Bar

Orifice
(mm)

Size

Line Pressure

Ambient: -10 C to 50 C
Materials in contact
with fluid :

Main valve :
Reinforced Nylon 6, St.st 303
Diaphragm:

12
Pilot pressure

NBR, Viton, EPDM or Polyurethane

10
8
6
4
2
0
-1

BSP/NPT

Size

3/4"

110

108

81

3/4"

1/8" BSP/NPT

1"

110

108

81

1"

1/8" BSP/NPT

1-1/2" 160

174

127 1-1/2"

1/8" BSP/NPT

185

127

1/8" BSP/NPT

2"

170

2"

10

Line pressure

Dimensions

6.8

SV-04-09

Technical Info

GC Pressure Operated Valves Index


BACCARA

Cylinder Operated General Purpose


1/4", 3/8", 1/2" 3/2 Way

Pilot
Pressure

NO IN

OUT

NC EX

DIVERTOR
IN

How to Order
NO
EX

Example : GC-2209N
Is a GC cylinder with brass
body, 1/4" BSP 3W with NBR seals.

GC

Body
Brass

Port
2

1/4" BSP
1/4" NPT
3/8" BSP
3/8" NPT
1/2"BSP
1/2"NPT

Function
20
21
30
31
40
41

General
Purpose

Seals
9

6.9

NBR
Viton
EPDM

N
V
E

NC
IN

GC Pressure Operated Valves Index


Technical Specifications
Functions:

3/2 Way

Ports size:

1/4", 3/8", 1/2" BSP & NPT

Pressure and flow:

See table

Temperature range:

Fluid: max 60 C

Size

Orifice
(mm)

1/4"

Vacuum-10 Bar

3/8", 1/2"

12

Vacuum-10 Bar

Line Pressure

Ambient: -10 C to 50 C
Materials in contact
with fluid :

Main valve :
Brass
Minimum Pilot pressure

Seals Seat:
NBR, Viton, EPDM

12
10
8
6
4
2
0
-1

10

Line pressure

1/4"

60

90

34

1/8"

3/8", 1/2"

70

100

45

1/8"

Dimensions

6.10

SV-04-09

Technical Info

GC Pressure Operated Valves Index


BACCARA

Globe Cylinder Operated General Purpose


3/4", 1", 1-1/2", 2" 3/2 Way

NC Ex
NO In

How to Order
Example : GC-4160-9P

NC In

NO Out

Is a GC Globe cylinder with nylon body,


1" BSP 3W with polyurethane seals.

NO Ex

Divertor In

GC

Body
Nylon

Type
4

Globe

Port
1

3/4" BSP
3/4" NPT
1" BSP
1" NPT
1-1/2"BSP
1-1/2"NPT
2" BSP
2" NPT

Function
50
51
60
61
70
71
80
81

6.11

General
Purpose

Seals
9

Polyurethane

GC Pressure Operated Valves Index


Technical Specifications
Functions:

3/2 Way

Ports size:

3/4", 1", 1-1/2", 2" BSP & NPT

Pressure and flow:

See table

Temperature range:

Fluid: max 60 C

Size

Orifice
(mm)

3/4", 1"

27

Vacuum-5 Bar

1-1/2", 2"

55

Vacuum-5 Bar

Line Pressure

Ambient: -10 C to 50 C
Materials in contact
with fluid :

Main valve :
Reinforced Nylon 6
Seal Seat:
Polyurethane
Pilot pressure
[Bar]

10
8
6
4
2
0

BSP/NPT

Size

3/4"

110

142

81

3/4"

1/8" BSP/NPT

1"

110

142

81

1"

1/8" BSP/NPT

1-1/2" 160

264

126

1-1/2"

1/8" BSP/NPT

274

126

2"

1/8" BSP/NPT

2"

170

Line pressure
[Bar]

Dimensions
E BSP

E BSP

D BSP
NPT

D BSP
NPT
A

6.12

SV-04-09

Technical Info

GC Pressure Operated Valves Index


BACCARA

Cylinder Operated Pinch Valve


2/2, 3/2 Way
General Description
These Cylinder operated 2/2, 3/2 way Pinch Valves are
recommended for use in applications where corrosive
or contaminated fluid must be controlled.
They can be used for industrial, laboratories and
irrigation control and analysis devices.

Notes
The valve performances are a function of the tube dimensions
and hardness.
Please consult our technical sales department.
Maximum tube diameter: 9.5mm (2/2 way valves only)

Pilot Pressure
Pilot Pressure

2/2 Way

How to Order
Example : GC-P-11
Is a Pinch Valve for 6x4 silicon tube, 2W.

GC-P

Tube

Function

6x4

2W

8x5 *

3W

9.5x6.5 *

* 2W only

6.13

3/2 Way

GC Pressure Operated Valves Index


Technical Specifications
Functions:

2/2, 3/2 Way

Tubes:

6x4, also 8x5, 9.5x6.5 for 2/2W only

Pressure range:

Fluid: according to tube specifications


Pilot: 3 - 8 bar

Temperature range:

Fluid: according to tube specifications


Ambient: -10 C to 50 C

Materials:

Valve :
Aluminium

Dimensions

28

44

50

28

28
25.4
M5

25.4

28

M5

2/2 Way

3/2 Way

6.14

SV-04-09

Main Contents

Accessories Idex

DIN 43650 Connectors


DIN 43650-A for GEM-SOL coils
Description
Housing:
Contacts:
Number of poles:
Contact spacing:
Cable entry:
Gasket:
Fixing screw:
Earth position:
Protection class:
Max. conductor section:
Standard circuits (housing black-grey):
Standard circuits (transparent housing):
LED colour (transparent):

Circuit Versions

LED + Diode
DC only

LED AC/DC
1

K
black - grey - transparent
screw with conductor protection
2 or 3 +
18 mm
PG9 - PG11 - 1/2 NPTF
NBR profile (other types on request)
M3 x 32
H 12 (opposite to cable entry)
IP 65 (mated)
1,5 mm2
See How to Order coding.
See How to Order coding.
amber

1+

LED + Varistor
AC/DC

Bridge rectifier
+ LED+Varistor
AC/DC

2xLED + 2xVaristor
AC/DC
1-

1+

2+

2-

2-

12/24/48
120/230[V]

12/24/48[V]

DIN 43650-B for GEVA-80 coils


Description
Housing:
Contacts:
Number of poles:
Contact spacing:
Cable entry:
Gasket:
Fixing screw:
Earth position:
Protection class:
Max. conductor section:
Standard circuits (housing black-grey):
Standard circuits (transparent housing):
LED colour (transparent):

Circuit Versions

12/24/48
120/230[V]

K
black - grey - transparent
screw with conductor protection
2 or +
11 mm
PG7 - PG9
NBR profile (other types on request)
M3 x 32
H 12 (opposite to cable entry)
IP 65 (mated)
1,5 mm2
See How to Order coding.
See How to Order coding.
amber

LED + Diode
DC only

LED AC/DC

LED + Varistor
AC/DC

1+

2-

12/24/48
120/230[V]

12/24/48[V]

12/24/48
120/230[V]

12/24/48
120/230[V]

7.1

3+

12/24/48
120/230[V]

40

40

23

Accessories Index

DIN 43650-C for GEVA-65 coils


Description
Housing:
Contacts:
Number of poles:
Contact spacing:
Cable entry:
Gasket:
Fixing screw:
Earth position:
Protection class:
Max. conductor section:
Standard circuits (housing black-grey):
Standard circuits (transparent housing):
LED colour (transparent):
Circuit Versions

black - grey - transparent


screw with conductor protection
2 or 3 +
8 mm
PG7
NBR flat (other types on request)
M2.5 x 28
H 6 (next to cable entry)
IP 65 (mated)
0,75 mm2
See How to Order coding.
See How to Order coding.
amber

LED + Diode
DC only

LED AC/DC
1+

2-

12/24/48[V]

LED + Varistor
AC/DC

12/24/48
120/230[V]

26.8

18.8

DIN 43650 Connectors

12/24/48
120/230[V]

TECHNICAL DATA
Description
No. of contacts
Cable entry

Standard

Value

2 or 3 +
P67
PG9
PG11
1/2NPTF

cable OD 4-6mm
cable OD 6-8mm
cable OD 8-10mm
cable OD 8-10mm

Fixing system
Termination
Max. contact screw torque VDE 0627
Contact surface
Contact material
Conductor cross section
Housing material
Flammability
Insert material
Insert material
Protection class (mated) IEC 60 529
Operating temperature
Nominal current
Max. contact current
IEC 60 512-3
Rated voltage
IEC 60 664
Rated impulse voltage IEC 60 664
Overvoltage category
IEC 60 664
Contact resistance
IEC 60 512-2
Insulation resistance
Pollution degree
IEC 60 664

7.2

SV-05-10

Main Contents

Engineering & Technical Info Index

Engineering & Technical Info Index

Engineering & Technical Info Index

Engineering & Technical Info Index

Engineering & Technical Info Index

Engineering & Technical Info Index

Engineering & Technical Info Index

Engineering & Technical Info Index

Engineering & Technical Info Index

Engineering & Technical Info Index

Engineering & Technical Info Index

Engineering & Technical Info Index

Engineering & Technical Info Index

You might also like