Professional Documents
Culture Documents
Samsung b1930n Monitor PDF
Samsung b1930n Monitor PDF
Model
: B1930N
ODM Vendor : INNOLUX
[ Important ! ]
SVC P/G was separated per ODM Vendor for
downloading the MCU code and EDID file.
So SVC P/G should be used according to ODM vendor.
The 10th digit is ODM vendor code.
Example LS19HANKBUTRU
U: INNOLUX, H: QISTA, G: TPV
SERVICE
TFT-LCD Monitor
Manual
Contents
1. Precautions
2. Product specifications
3. Disassembly and reassembly
4. Troubleshooting
5. Exploded View & Parts List
6. Wiring Diagram
7. Schematic Diagram
B1930N
Refer to the service manual in the GSPN (see the rear cover) for the more information.
Web Site
http://service.samsungportal.com
http://latin.samsungportal.com
CIS
Europe
http://cis.samsungportal.com
http://europe.samsungportal.com
China
Asia
http://china.samsungportal.com
http://asia.samsungportal.com
Mideast &Africa
http://mea.samsungportal.com
56
3-1 Disassembly
Caution: 1. Turn the monitor of before beginning the disassembly process.
2. When disassembling the monitor, do not use any metal tools except for the provided jig.
3. Disassemble the monitor carefully as directed in the following procedures.
Description
Photo
2.
3.
11
Screws
12
7.
Description
Photo
13
Screws
14
15
Memo
16
4 Troubleshooting
4. Troubleshooting
4-1 Troubleshooting
1. Check the power state and the cable connections.
Check the connections of the power and signal cables.
Check whether the function button operates normally.
2. Check TEST GOOD OSD
- The Purpose and Function of the self-test
A self-test has been added to easily recognized whether the monitor has fault or not and
consequently to minimize customer claims for non-malfunctions of the product.
- How to perform a self-test
Press the menu button in the DPMS state, and determine whether the monitor is normal or not.
No screen
Focus fault
Screen trembling
Notes:
1. Set custom mode as follows before beginning a repair.
Resolution: 1360 x 768
H-frequency: 47.7 KHz
V-frequency: 60 Hz
2. If the screen is blank, check whether the power cord is connected correctly.
3. The circuits to check:
When the raster does not appear: The Function PCB, Main PCB, I/P PBA
When 5V is generated but a blank screen is displayed: Main PCB
When 5V is not generated: I/P PBA
4. *Press the MENU button and hold down the
return the monitor to default mode.
17
4 Troubleshooting
Symptom
Major checkpoints
- W hen turning on the Power button after connecting the power cable, the LED
at the front of the monitor does not operate.
- W hen turning on the Power button after connecting the power cable, the LED
at the front of the monitor does not operate.
- Check the IP board power fuse and the IP board output power.
- Check the connections for the IP board and the Main board inside the monitor.
- Check the Main board power part and also check whether there is any
abnormal output at any of the other output terminals.
Diagnostics
NG
Replace the IP board.
NG
ok
Check and replace the Main board.
Caution
18
4 Troubleshooting
Attached PDF
DC-DC
19
4 Troubleshooting
D iagnostics
NG
Is X1 oscillating correctly?
OK
D o the R G B inputs appear at
R 114,
R115 and R 116?
OK
NG
NG
OK
Is D C 5V m easured at pins 1, 2, and
3
of the C N103?
OK
NG
Check the +5V_Panel signal
and the BL_EN signal.
C aution
20
4 Troubleshooting
HSYNC VSCIN
U105 Pin 16 17
LVDS Connector
CN103
Is X101
oscillating correctly?
Attached PDF.
21
4 Troubleshooting
22
4 Troubleshooting
23
Remarks
4 Troubleshooting
4-5 Adjustment
4-5-1 Service Adjustment Conditions
1. Precautions before a Service Adjustment
1) Check whether the devices for the service adjustment are operating normally.
2) Secure a space that is sufficiently wide for disassembling the monitor.
3) Prepare a soft mat on which the monitor will be disassembled.
2. Entering Service Mode
Entering:
Menu
Exiting:
Power OFF
Brightness 0
Contrast 0
Parallel
24
4 Troubleshooting
1. Checking the MCU code version and checksum after entering SVC Mode.
2. Entering SVC Mode
- Adjust the Brightness and Contrast values to 0.
- Hold down the Enter button for five (5) seconds.
- The SVC Function OSD is displayed.
- To exit the SVC Function, turn the power off.
3. Safe Mode
- When the input signal is higher than the supported frequency of the product, safe mode gives users some
time (one minute) to change the video card settings to the Recommended Mode settings.
25
4 Troubleshooting
2. Press the button to change the setting to On or Off.
After replacing the panel, move the panel item and hold down the Menu button for five (5) seconds.
The Ch. No is incremented by 1 and then both the on time and cycle are set to 0.
26
4 Troubleshooting
1) Equipment set-up: Equipment (VGA Cable, Parallel Cable, Samsungs DDC Manager)
Hardware setup: Connect LCD to PC Print Port as below:
VGA Cable
Print Port
VGA
(D-Sub)
27
4 Troubleshooting
2) Write EDID: Click Model button to show the Change Model Window.
Then Select a Model which you want to write EDID (Detailed Model as Table 1)
28
4 Troubleshooting
2) Write EDID: Select File- Auto Write to enable EDID Writing.
29
4 Troubleshooting
2) Write EDID: It will auto write when you enter a S/N which is 15 chars, Pic as below:
30
4 Troubleshooting
3) Finished: Successful EDID written when it shows PASS logo as below:
31
4 Troubleshooting
Pa
VGA Cable
rallel Cable
Print Port
VGA
(D-Sub)
32
4 Troubleshooting
2) Program process: Open the Attached Mstar ISP Tool for Samsungs DDC Manager (Version
4.3.9.5 E) . Run it. Click Connect ' button, It will select flash memory type automatically
33
4 Troubleshooting
2) Program process: Click Read ' button, then select the MCU Code
34
4 Troubleshooting
2) Program process: Sometimes, if you program error, please try again with no worry
3) Finished
35
F001A
M0215
M0014
R001A
SB03A
FB01A
P001A
SB04A
Code No.
Qty
SA/SNA
F001A
BN81-04556A
SA
FB01A
BN81-04582A
A/S-BOARD P-FUNCTION;LE23CK-612,79451150
SA
M0014
BN81-04824A
SA
M0215
BN07-00610A
LCD-PANEL;M185B1-L02,CM18B12,6bit Hi-FRC
SA
P001A
BN81-04567A
SA
R001A
BN81-04550A
SA
SB03A
BN81-04589A
SA
SB04A
BN81-04553A
SA
Remark
5-1
Location No.
Code No.
Qty
SA/SNA Remark
0.1
M0215
BN07-00610A
LCD-PANEL;M185B1-L02,CM18B12,6bit Hi-FRC
SA
SA
0.1
R001A
BN81-04550A
A/S-ASSY COVER
P-REAR;LE18CG,71405E18CG0
0.1
SB04A
BN81-04553A
A/S-ASSY STAND
P-BASE;LE18CG,71402E18CG0
SA
0.1
F001A
BN81-04556A
A/S-ASSY COVER
P-FRONT;LE18CG,71403E18CG
SA
0.1
M9892
BN81-04560A
A/S-CUSHION
BOTTOM;LE18CG,50610E18CG01R
SNA
0.1
M9892
BN81-04561A
A/S-CUSHION TOP;LE18CG,50610E18CG00R
SNA
0.1
P001A
BN81-04567A
SA
0.1
FL06
BN81-04573A
SA
0.1
M9891
BN81-04581A
A/S-CARTON;LE18CG,B1930N,50602E18CG00R
SNA
0.1
FB01A
BN81-04582A
A/S-BOARD P-FUNCTION;LE23CK-612,79451150
SA
SA
0.1
SB03A
BN81-04589A
A/S-ASSY STAND
P-BAR;LE20CN,71401E20CN00
0.1
EC18
BN81-04591A
SA
0.1
EC13
BN81-04688A
SA
SA
0.1
EC11
BN81-04704A
A/S-POWER CORD;16A250V,BLK
1.5M,45307080
0.1
ACCE1
BN81-04820A
A/S-ACCESSORY;FOR
EU,B1930N,703061000302
SA
0.1
M0014
BN81-04824A
SA
5-2
6 Wiring Diagram
6 Wiring Diagram
6-1 Wiring Diagram Main Board
.
Panel
Lamp wire for Panel
CN501
1 VCC5V
3 VCC5V
4 GND
5 GND
6 ON/OFF
C
N
8
0
1
C
N
1
0
1
7 BRIGHTNESS
10 PWR_Ctrl
CN103
Power
conn
1 VCC5V
1 5V_Panel
16 RXCLK+
2 VCC5V
2 5V_Panel
17 RXCLK-
5 GND
3 5V_Panel
18 GND
6 GND
4 5V_Panel
19 RX2+
20 RX221 GND
22 RX1+
7 ON/OFF
5 5V_Panel
8 BRIGHTNESS
6 GND
9 PWR_Ctrl
7 GND
9
23 RX124 GND
10
25 RX0+
11
26 RX027 GND
8 GND
Power ASS'Y
12 GND
CN502
13 RX3+
28
14 RX3-
29
15 GND
30
AC Power
1 RED+
Main ASS'Y
2 GREEN+&SOG
3 BLUE+
4
5 GND
6 RED7 GREEN-
1 Key-Power
8 BLUE-
2 Touch-SDA
3 Touch-SCL
# CHK-DSUB
4 Key-ATTN
5 PWR_Ctrl
# DDC-SDA-VGA
6 GND
# H-sync
7 NC
# V-sync
8 NC
# DDC-SCL-VGA
CN104
Keypad Control
39
CN102
VGA Input
6 Wiring Diagram
IP Board
Keypad Connector
(Connector to Keypad)
RGB Connector
(Connector to PC)
40
6 Wiring Diagram
CN101
Functions
Supplies 5V from the power board to the main board and transmits the PWM output
from the power board to the inverter.
CN801
*When a problem occurs: The No Power and Blank Screen errors may occur.
CN501 ~ CN502
Transmits the lamp current (6mA ~ 7mA) generated in the inverter to the lamp of the
panel.
*When a problem occurs: The Blank Screen error may occur.
CN104
CN105
Transmits the LVDS signals from the main board to the panel.
*When a problem occurs: The Blank screen and No Power errors may occur.
6-4 Cables
Use LVDS 30P FFC cable
Code
Photo
41
6 Wiring Diagram
Memo
42