Professional Documents
Culture Documents
1]
Match the cutting tools with uses.
Cutting Tools:
1) File 2) Hacksaw 3) Chisel 4)Scraper
Uses: A] To Remove small amount of metal and finishing purposes
B] To remove large amount of metal up to 6mm
C] To cutting the metal o scribed line
D] To remove the metal on scribed line
E] To remove high spot by hand process for obtaining high degree of Accuracy
Ans: 1-A
2-C
3-B
4-D
2]
Match the cutting tools with uses.
Cutting Tools:
1) Drills 2) Reamer 3) Taps 4) Dies
Uses: A] For making hole on a job
B] To accurate finishing hole and to remove burrs
C] For cutting external threads on cylindrical job
D] For cutting internal threads in a hole
Ans: 1-A
2-B
3-D
4-C
3]
Match the marking tools with uses.
Marking Tools
1) Marking table 2) Try Square 3) Scriber 4) Divider
Uses: A] For placing the job and tools on it for marking
B] To draw a scribe line on metal, to indicate dimension
C] For marking parallel lines and checking right angles of job
D] To scribe circles, arcs and to find out center of round rod
Ans: 1- A
2C
3-B
4-D
4]
Match the marking tools with uses.
Marking Tools
1) Surface Plate 2) Universal Surface Gauge 3) Vernier height gauge 4) punches
Uses: A] To support the tools for marking and checking
B] To register mark to keep up the lines visible till the operation is over
C] For talking accurate measurement of height of a job or marking
D] For Scribe parallel line locating centre of round bar and for checking of height
Ans: 1 A
2- D
3- C
4-B
5] Match the marking tools with uses.
Marking Tools
1) Trammel 2) Bevel protractor 3) Combination set 4) Jenny Caliper
Uses: A] For draw a large circles, arcs two parallel lines and also used for laying out materials
for boilers, tanks, bridges towers etc.
B] To measurement of layout of angles
C] For measure the angles with different heads.
D] To scribe parallel lines and find centre of cylindrical round bar
Ans: 1-A
2-B
3-C
4-D
E] Different types of making wire edges and slots, holes, round, square in different
shapes and sizes and Made in this
Ans: 1-A
2-A
3-B
4- D
5-E
12] Match the forging and black smithy tools with uses.
Forging and black smithy tools
1) Shavel 2) Sprinker 3) Pocker 4) Tongs
Uses: A] For holding jobs in hot conditions and protect the hand from heat and prevent shear while
Beating on cold condition
B] To make clear way and to know the position of the heated jobs in the Furnace
C] To control the fire by filling it with water
D] To carry over the fuel into forge as well to remove the slag, ash etc from the fire
Ans: 1-D
2-C
3-B
4-A
13] Match the forging and black smithy tools with uses.
Forging and black smithy tools:
1) Anvil 2) Swage 3) Hardie 4) Drift
Uses: A] To enlarge the hole in hot metals
B] It is hole of Anvil, hot metals is kept on it and cut by striking at it
C] For finishing the round job
D] For hammering a hot job
Ans: 1-D
2-C
3-B
4-A
14] Match the forging and black smithy tools with uses.
Forging and black smithy tools:
1) Fuller 2) Flatter 3) Cone 4) Rake
Uses: A] used in conjunction with each other for making hollow V grooves and necks in round corner.
B] For finishing the surface of the plain job
C] to make round rings of different sizes in forging works
D] To pull the charged fuel over the job
Ans: 1- A
2-B
3-C
4-D
15] Match the Gas welding tools with uses:
1) Spark Lighter 2) Tip Cleaner 3) Cylinder Key 4) Wire brush
Uses: A] For lighting the gas released from welding torch
B] For opening and closing the gas Cylinders spindle valve.
C] For cleaning the hole in Nozzle and also used for removing slag from the job after welding
D] For cleaning the jobs before and after welding
Ans: 1- A
2- C
3- B
4- D
16]
Match the Gas welding equipments with uses:
Gas Welding Equipments:
1) Oxygen Cylinder 2) Acetylene Cylinder 3) Gas Regulator 4) Blow pipe
Uses:
A] it is black color and its valve has right hand thread
B] It is maroon color and its valve has left hand thread
C] To supply the gas to welding torch at a proper and reduced pressure
D] For gases supplied to the welding torch from cylinder
Ans: 1-A
2-B
3-C
4-D
17]
match the Welding Safety Equipments with used.
Welding Safety Equipments:
1) Welding torch 2) Welding goggles 3) Hand gloves 4) Apron
Uses: A] to mixed oxygen and acetylene gases desired proportion in it
B] For protects of eyes against and possible bad effect of the flame
C] For the protection of hand against any possible burn during welding
D] For protection body from spark while doing welding
Ans: 1-A
2-B
3-C
4-D
18]
Match the Arc welding equipments with uses:
Arc Welding Equipments:
1) Welding Cable 2) Cable connector 3) Earth Clamp 4) Electrode holder
Uses: A] To pass the current from welding machine to the electrode holder
B] To hold the electrode
C] For connecting the earth and cable to placed on the welded jobs while welding.
D] For joining two cable pieces or for connecting the cable to the welding machine.
Ans: 1-A
2-D
3-C
4-B
19]
Match the Arc welding equipments with uses:
Arc Welding Equipments:
1) Weld gauge
2) Welding electrode
3) Oxygen Cylinder
4) Acetylene Cylinder
Uses: A] used in Arc Welding
B] For measuring the depth of weld
C] Oxygen is store in a cylinder is called
D] Acetylene gas is store in a Cylinder is called
Ans: 1- B 2- A
3- C
4- D
20]
Match the drilling attachments with uses.
1) Drill Chuck
2) Drill Sleeve
3) Drill Drift
4) Drill bit
Uses: A] For making hole on a job
B] To remove the big drill or sleeve from spindle
C] To hold the shanks of different size from spindle of machine.
D] To hold the drills.
Ans: 1- D
2-C
3- B
4- A
21]
Match the tools with uses.
1) Counter boring 2) Counter sinking 3) spot facing
4) Reaming
Uses: A] making enlarging top of holes to round head screw to sit
B] Making cone shaped enlarging of hole months for counter shrunk screw to fit
C] Making accurate size of hole and finishing
D] Make level for sealing of washer keys.
Ans: 1- A
2- B
3-D
4- C
22]
match the lathe accessories with used
1) Chuck 2) Carrier
3) Catch plate
4) Face Plate
Uses: A] To grip the jobs is tightened in
and slots with the help of nut- bolts
B] To grip the jobs to be turned
C] To gripping bent types jobs
D] The jobs tied in this and fitted in the catch plate
Ans: 1- B
2- D
3- C
4- A
23] match the lathe accessories with used
1) Steady rest
2) mandrel 3) Lathe centre
4) Tail stock
Uses: A] To support a cylindrical lengthy job
B] For turning a job along its entire length and for speed up the production process
C] It is fitted with head stock, and tail stock to grip job.
D] For centre to centre turning of lengthy.
Ans: 1- A
2- B
3- C
4- D
24]
match the following fastener with used
1) Nut
2) Bolt
3) Rivet
4) Screw
Uses: A] To join small parts of machine
B] To join two metallic sheets.
C] For fastening purposes, it having a threaded hold in it.
D] For fastening purposes the cylindrical rod have threaded on one end and
head is another end
Ans: 1-C
2- D
3- B
4- A
25]
Match the following with uses.
1) Stud
2) Cotter
3) pin
4) Key
Uses: A] The piece of metal inserted on axial direction between hub and shaft and making
Them to rotate jointly
B] For locking jointly
C] To join two such parts of machine it having standard threads on both ends.
D] To join two parts of a machine like a key
Ans: 1- C
2- D
3- B
4-A
26]
Match the following with uses.
1) Jigs
2) Fixture
3) Template
4) Washer
Uses: A] To protect the threads of bolt or screw and helps loosening nut easily.
B] To hold the job and guide the tool
C] To hold the job during turning, milling and shaping operation
D] For marking similar jobs at a time and also used for checking.
Ans: 1- B
2- C
3- D
4A
27]
Match the following with uses.
1) Lubricator
2) Lubricant
3) Coolant
4) Lubrication
Uses: A] Increase tool life and protects job from rust
B] To lubricate the machine parts
C] Increase the machine life and protects the jobs from rust
D] The process of putting lubricant at the places of Friction between two different parts of a
machine
Ans: 1- B
2- C
3- D
4- B
28]
Match the following with uses.
1) Abrasive
2) Bond
3) Aluminum Oxide
4) Grinder
Uses: A] To making grinding wheel
B] To giving fine finish to surface of job
C] To blind Abrasive grains to making grinding wheel
D] Artificial abrasive.
Ans: 1- A
2- C
3- D
4- B
29]
Match the following with uses.
1) Welding transformer
2) Generator 3) Rectifier
4) Bearing
Uses:
A] To give support to the shafts while they are in motion
B] Convert the AC main supply into Ac welding supply
C] To convert AC into DC welding supply
D] To generate DC for Arc welding
Ans: 1- B
2- D
3- C
4- A
30]
Match the following with definitions.
1) Stress
2) Strain
3) Opaque
4) Conductivity
Uses: A] Change in length/Original length
B] Load / Area of cross section
C] We cannot see through metals.
D] The ability to carry the electrical current or heat.
Ans: 1- B
2- A
3C
4- D
31] Match the following with properties.
1) Toughness
2) Brittleness
3) Ductility
4) Malleability
Properties: A] Metal can draw into wires.
B] Metal can be hammered or rolled out without breaking or cracking.
C] It does not break or deform even after bending or twisting.
D] The metal breaks and disintegrates into pieces.
Ans: 1- C
2- D
3- A
4- B
32]
Match the following with Flames.
1) Equal quality of oxygen and acetylene gas
2) Percentage of Acetylene gas is less than Oxygen.
3) Percentage of Acetylene gas is more than Oxygen.
Flames:
A] Neutral Flames
B] Carburizing Flame
C] Oxidizing Flame
Ans: 1- A
2- C
3- B
33]
Match the following pulleys with machine.
1) Stepped pulley 2) V. Grooved pulley 3) Split Pulley
4) Cone Pulley
Uses: A] In electric motors and Automobiles
B] In drilling machine, lathe machine
C] In saw machine
D] In a set of two pulleys.
Ans:
1B
2- A
3C
4D
34]
Match the following with Products.
1) Blast Furnace produce 2) Cupola Furnace produce
3) Puddling Furnace Produce
Products:
A] Pig Iron
B] Cast Iron
C] Wrought Iron
Ans: 1- A
2- B
3- C
35]
Match the percentage of carbon contect with steels.
1) Low Carbon Steel
2) High carbon steel
3) Medium Carbon Steel
Percentage of Carbon:
A] 0.7 % to 1.5 %
B] 0.3 % to 0.7 %
C] 0.07 % to 0.25 %
Ans: 1- C
2A
3- B
36]
Match the following fits with definition.
1) Clearance fit
2) Transition Fit
3) Interference Fit
Defination: A] Shaft size is less than hole size
B] Shaft size is equal to hole size
C] Shaft size is bigger than whole size
Ans: 1- A
2- B
3- C
37]
Match the following Files with uses.
1) Straight file
2) Cross File
3) Draw File
4) File card.
Uses: A] The metal quickly cut.
B] The entire job becomes plain and smooth
C] Method is done to bring finishing on the job
D] To remove chips.
Ans: 1 A
2- B
3- C
4- D
38]
Which file is used to rapid removed of soft materials such as aluminum lead, wood and
leather?
1) Single cut file
2) Double cut file 3) Rasp Cut File
4) Curved cut File
39] Which file having 12 teeth per cm?
1) Rough File
2) Bastard File
3) Smooth File
4) Dead Smooth File.
40] Which blade is hardened to the full length between the pin holes?
1) Flexible blade
2) Spring back blade 3) All hard blade
4) Flexible Center blade
41] Wave set of blade pitch is
1) 0.8 mm
2) 1.0 mm
3) over 1.0 mm
4) Below 0.8 mm
53]
Match the instrument s with least count
1) Steel rule 2) Vernier Caliper 3) Micrometer
Least Count: A] 0.5 mm B] 0.01mm C] 0.02mm
Ans: 1 A
2C
3B
4) 1 Cm
D] 10mm
4D
54]
The tool which is used to support the job and to provide a vertical or angular plane for marking
1) Try Square
2) Scribing black 3) Angle plate
4) Surface Plate
55]
The slots are provided an angle plate for:
1) Accommodating bolts 2) Hanging with hooks
3) reducing weight
56]
The tool which is stated by size number
1) Surface plate
2) Angle plate
3) Marking table
4) V block
57]
Match the parts of combination set with their uses.
1) Square head
2) Centre head
3) Protractor Head
Uses of head:
A] Marking and measuring any angle
B] Checking the 45 degree and 50 degree angle
C] To find the centre of cylindrical job
Ans: 1 B
2-C
3A
58]
Match the Gauges with uses.
1) Drill Gauge
2) Drill Point Gauge
3) Centre Gauge
4) Feeler Gauge
Uses: A] To measure the size of drill
B] To check the lip angle of drill bit after grinding
C] To determined size of small gauge and clearance
D] To Cutting tool for the cutting V threads.
Ans: 1 A
2B
3D
4
59]
The file used for general purpose filing is called
1) Square File
2) Flat File
3) Mill file
4) Hand file
60]
Pig Iron is refined to produce cast iron in Furnace called
1) Blast Furnace
2) Cupola Furnance
3) Puddling Furnace
4) Bessemer Method
61]
Pig iron is refined in a puddling Furnace and the product is known as:
1) Pig Iron
2) Cast Iron
3) Wrought Iron
4) Steel
62]
The File which is used for Round purpose is called.
1) Flat File
2) Triangle file
3) Round file
4) Square File
63]
The file is pushed and pulled over the job. This every two actions are called.
1) One Stroke of File 2) Two stroke of file
3) Three stroke of files
4) Four Stroke of file
64]
The type of file which is commonly used in lathe work is called
1) Warding file
2) Needle file
3) Mill file
4) Piller file
65]
The act of joining slip Gauges is termed as:
1) Grouting
2) Creeping
3) Seaming
4) Wringing
66]
If in a micrometer, Zero on barrel and thimble are coinciding but still thee is gap between the
face Anvils the error is known as:
1) Positive error
2) Negative error
3) Zero error
4) Normal error
67]
The hammers with head made of lead, copper are called:
1) Soft hammer
2) Hard hammer
3) Mallet
4) Sledge hammer
68]
The tool is used to finish drilled hole is called:
1) Reamer
2) File
3) Hacksaw
4) Drill
69]
While drilling a large hole, a small size hole is first drilled the hole is known as:
1) Latest hole
2) Minor hole
3) Pilot hole
4) Drilled hole
70]
Back portion of the drill cutting edge is known as:
1) Shank
2) Flutes
3) Dead Centre
4) Heel
71]
Last pointed end of the drill is called:
1) Lip
2) Dead Centre
3) Shank
4) Heel
72]
Cutting inside thread is called
1) Tapping
2) Reaming
3) Dyeing
4) Drilling
73]
Cutting outside thread is called
1) Tapping
2) Reaming
3) Dyeing
4) Drilling
74]
The top surface which joints the two sides of a thread is known as:
1) Root
2) Crest
3) Pitch
4) Lead
75]
The bottom surface which joints the two sides of thread is known as:
1) Crest
2) Root
3) Lead
4) Pitch
76]
The included angle between the sides of thread measured in an axial plane is known as:
1) Angle of thread 2) Pitch of thread
3) Depth of thread
4) Form of thread
77]
The surface of the thread which connects crest and the root is known as:
1) Flank or side
2) Crest
3) Root
4) Pitch
78]
The property due to which any metal can cut other metal is called:
1) Hardness
2) Brittleness
3) Toughness
4) Ductility
79]
An alloy of copper and zinc is called:
1) Brass
2) Bronze
80]
An alloy of copper and tin is called:
1) Brass
2) Bell metal
3) Lead
4) Gold
3) Bronze
4) 2 and 3
81]
An alloy of copper, tin and zinc is called:
1) Brass Metal
2) Bronze Metal
3) Gun Metal
4) Soft Metal
82]
Brittleness in the metal when hot is called
1) Hot Shortness 2) Hot highest
3) Hot weakness
4) Hot Minus
83]
A key with head is called
1) Gib Head key 2) Wood ruff key
3) Feather Key
84]
Joining of two metals together without melting is known as:
1) Riveting
2) Welding
3) Soldering
4) Round Key
4) Brazing
85]
The mutual connection between two joining parts is called:
1) Fit
2) Limit
3) Loose
4) Tolerance
86]
The difference between upper limit and lower limit is called:
1) Tolerance
2) Allowance
3) Bilateral tolerance
4) UNMATERAL tolerance
87]
It is an intentional difference in the size of mating part is called:
1) Tolerance
2) Interference
3) Allowance
4) Transition
88]
The device for guiding the tool s called
1) Fixture
2) Jigs
3) Clamp
4) Leg vice
89]
A shaft at centre of wheel is called
1) Axel
2) Housing
4) Square rod
3) Cylindrical rod
90]
The maximum dia of work which can accommodate when held between centres in lathe is
known:
1) Swing diameter
2) Core diameter 3) Major diameter
4) Length of bed
91]
Double helical gears are called:
1) Herring bone gear
2) spur gear
3) Bevel Gear
4) Worm gear
92]
The process of increasing cross section of a bar at the expanded of its length by forging is
called:
1) Upsetting
2) Drawing out
3) Drifting
4) Jumping
93]
Front end of Anvil is called
1) Face
2) Base
3) Beak
94]
The square hole of the tail end of Anvil is called:
1) Base
2) Face
3) Hardie Hole
4) Hardie
4) Punch Hole
95]
Before welding the joining parts of the assembly is kept at square specific distance is called:
1) Root Gap
2) Blow Hole
3) Porosity
96]
Any change that occurs during welding in shape and size of joining pieces is known as:
1) Distartion
2) porosity
3) Root Gap
4) Blow hole
97]
A group of pin hole in the weld is called:
1) Porosity
2) Distartion
3) Root Gap
4) Blow Hole
98]
A large hole in the weld is called:
1) Blow hole
2) Punch Hole
4) Face
3) Hardie hole
99]
The distance between adjacent teeth is known as:
1) Pitch of the blades
2) All bard blade
3) flexible blade
4) Flank
4) Welder
4) Wireman
3) Good person
4) Austenite
104]
the distance, which the cutting edge of tool passes over the material in a minute while
Machining is known as:
1) R.P.M.
2) Feed
3) Machine Speed
4) Cutting Speed
105] The process of applying oxide on aluminium is known as:
1) Oxidizing
2) Anodizing
3) Galvanizing
4) Cyninding
4) Flux
107] the portion behind the cutting edge is grinded at a special angle it is known as:
1) Rake angle
2) Lip angle
3) cutting angle
4) Clearance angle
108] steel which contain 0.8 % to 2.1% of carbon is called:
1) Hypo eutectoid steel
2) Eutectoid steel 3) Hyper eutectoid steel 4) Carbon
109] the art of cutting the corners of metallic sheet for making cuboid shaped job is called:
1) Seaming
2) Punching
3) Notching
4) Piercing
4) Swazing
4) Tapped Nut
112] A minimum measurement that can correctly read with a vernier caliper is called:
1) Zero reading
2) Least count
3) Main scale Reading
4) Actual reading minus zero error
113] an angle which is less than 90 degree is called:
1) Shluse angle
2) Acute angle
3) Right angle
114] a plug Gauge which has its Go and No Go sizes on the same end is known as:
1) Single ended plug gauge
2) Double ended plug Gauge
3) Progressive plug Gauge
4) Continuous plug Gauge
115] the cutting tool used to finish and enlarge a hole is known as:
1) Drill
2) Tap
3) Die
4) Reamer
116] the grooves provided on the entire length of the body of a twist drill are called:
1) Lips
2) Margins
3) Flutes
4) Webs
117] a hole which is not made through full depth of component is known as:
1) Core hole
2) Pin hole
3) Blind Hole
4) Bore Hole
118] the relief angle given behind the cutting lips is called:
1) Lip clearance angle
2) Helix angle
3) Rake angle
4) counter Sinking
120] the distance a drill advances into job is one complete revolution is known as:
1) R.P.M.
2) Cutting speed
3) Feed
4) Machine speed
121] the distance through which a screw advances axially in one turn is called:
1) Pitch of thread
2) Lead of thread 3) Depth of thread
4) Diameter of thread
122] a drilled hole after tapping is called:
1) Core hole
2) chain hole
3) Tapped hole
4) Reamed hole
123] in a gear, the pitch diameter divided by the number of teeth is called:
1) Module
2) Pitch
3) Addendum
4) Dedendum
124] the height from the pitch circle of a gear to the tip of the tooth is called:
1) Addendum
2) Dedemdum
3) Centre distance
4) Crest
125] the sum of addendum and dedendum of the tooth of gear is called:
1) Whole depth
2) Tooth depth
3) Working depth
4) Root depth
126] the depth of the tooth space a gear below the pitch circle is called:
1) Addendum
2) Dedendum
3) Centre distance
4) crest
127] the measure size of the dimension of a component is called:
1) Basic size
2) Nominal size
3) Allowed size
4) Actual size
128] In case hardening process ammonia gas is introduced on steel the process is known as:
1) Cyaniding
2) Nitriding
3) Carburizing
4) Anodising
129] during heat treatment when carbon is dissolved to form solid solution it is known as:
1) Ferrite
2) Pearlite
3) Austenite
4) Cementide
130] the process of increasing carbon percentage on the surface of low-carbon steel is known as:
1) Hardening
2) Nitriding
3) Carburizing
4) Tempering
131] the process of reduction of the iron ore to pig iron is known as:
1) Swazing
2) Smelting
3) Seeming
4) Scraping
132] the process of heating steel to about 40 degree above the upper critical temperature and
cooling it in
still air to room temperature is known as:
1) Hardening
2) Annealing
3) Normalising
4) Tempering
133] the thickness of sheet metal is indicated by a series of numbers, which is called as:
1) Number size
2) Standard wire gauge 3) Standard size
4) None of the above
134] the type of the hammer which both the faces are flat and which is used for heavy work in
smithy shop is called:
1) Bell pane hammer
2) Cross pane hammer
3) Claw hammer
4) Sledge hammer
135] Smooth side of a leather belt is called:
1) Flesh side
2) Hair Side
3) Right side
4) Left side
4) Stepped pulley
4) Stepped pulley
3) Cone Pulley
138] Ability of one material to penetrate into another without Fracture is called:
1) Toughness
2) Hardness
3) Brittleness
4) Malleability
139] Characteristic of metal by which they become Fluid through the Application of heat is called:
1) Fusibility
2) Tencity
3) Conductivity
4) Malleability
140] Oil in water Emulsion is called:
1) Cooling liquid
2) Cutting emulsions
3) Viscosity
3) Viscosity
142] the factor ultimate strength/ allowable unit stress is called as:
1) Stress
2) Strain
3) Factor of safety 4) Modulus of Elasticity
143] Jenny Caliper is also called:
1) Odd leg caliper
2) Hermaphrodite caliper 3) Venier Caliper
144] Curved cut file is also called is:
1) Single cut file
2) Second cut file
145] Wing nut is also called:
1) Cup nut
2) Ring Nut
4) 1 & 2
3) Rasp cut
4) Vexin File
3) Square Nut
4) Fly Nut
3) Margin
4) Shank
3) spiral drill
4) Shell Reamer
3) Minor dia
4) Crest
3) Root
4) Crest
4) Marking instrument
4) Warding file
3) Plug gauge
4) Ring gauge
3) Steady rest
4) Mandrel12.
3) Mandrel
4) Lather centre
3) Grooving
4) Corrugating
3) Worm thread
4) Knuckle thread
3) collet chuck
4) Universal chuck
3) Worm gear
3) Stainless steel
4) Venadium steel
4) Trepanning
167] The process of cooling steel piece in oil or water after heating its upper critical point is called:
1) Hardening
2) Tempering
3) Quenching
4) Annealing
168] the process of joining the various parts of the machine is called:
1) Riveting
2) Fastening
3) Brazing
4) Welding
169] the process of joining two metallic sheets is called:
1) Fastening
2) Riveting
3) Soldering
4) Blanking
170] the process of zinc coated on the Iron is called:
1) Anodizing
2) Galvanizing
3) Tining
4) Painting
171] the process of Tin solution CC at the Iron is called:
1) Galvanising
2) Tinning
3) Painting
172] Steel rule is made of:
1) Cast iron
2) Zinc
3) Brass
173] File is made of:
1) H.S.S.
2) H.C.S.
3) Cast Iron
4) Electroplating
4) Stainless steel
4) Special tool steal
3) Pig Iron
4) Cast Iron
3) pig Iron
4) Cast iron
3) H.C.S.
4) H.S.S.
3) Cast Iron
4) Tungsten steel
3) Tool steel
4) Bronze
3) Cast Iron
4) Phosphorus bronze
3) Mild steel
4) Tool steel
4) Mild steel
2) Cast Iron
3) Mild steel
3) bronze
4) Tool steel
3) Cast Iron
4) Forged steel
4) Mild steel
3) Cast Iron
4) Tungston Steel
3)Tungston Steel
4) Chromium Steel
4) Mild steel
4) Alloy steel
3) Cast Iron
4) Zinc
3) Mild steel
4) Mild steel
2)Bell Bronze
3) Stainless steel
4) Manganese Steel
3) Stainless steel
4) Manganese Steel
4) Alloy Steel
3) 5 to 10 degree
4) 12 to 15 degree
3) 90 degree
4) 120 degree
205] V Block is used to hold round bars it has a vee groove which is usually:
1) 30 degree
2) 60 degree
3) 90 degree
4) 120 degree
206] V Blocks are available in grade of:
1) 0 &1
2) 1 & 2
3) A1 & A2
4) A & B
4) 125 cm
4) 0.08 mm
4) 0.10 mm
4) 0.20 mm
4) 25
215] The value of each Vernier scale division of vernier bevel protractor is:
1) 1 degree
2) 5 minute
3) 1 degree 55minute
4) 2 degree
216] The value of each main scale division of vernier bevel protractor is:
1) 1 degree
2) 5 minutes
3) 1 degree 55 second
4)1/2 degree
4) 5 degree
4) 0.02 mm
3) 0.001 mm
4) 0.0001 mm
3) 50 HRC
4) 63 HRC
222] For general use in workshop, slip gauge of which grade are used:
1) Grade I
2) Grade II
3) Grade 0
4) None of the above
223] The point angle of twist drill for general purposes is:
1) 135 degree
2) 118 degree
3) 90 degree
4) 60 degree
224] The lip clearance angle of Twist drill for general purpose should be
1) 3 to 5 degree
2) 4 to 6 degree
3) 8 to 12 degree 4) 12 to 15 degree
225] The angle of drill grinding gauges is:
1) 59 degree
2) 118 degree
3) 121 degree
4) 124 degree
4) 70 degree
227] The most suitable pitch of the hacksaw blade for cutting thin section tubes is:
1) 0.8 mm
2) 1.0 mm
3) 1.4 mm
4) 1.8 mm
228] The suitable pitch of hacksaw for cutting solid brass is:
1) 1.8 mm
2) 1.4 mm
3) 1.0 mm
4) 0.8 mm
4) MT -4 Taper
4) 1 : 96
3) 60 degree
3) Length of spindle
3) Size number
15.
4) 29 degree
4) None of the
4) Length X width
4) size of the
4) stainless steel
4) None of the above
4) Angle
4) None of the above
282] To measure the machined or field surface, which one of the following instrument can be used:
1) Gauge
2) Dial Test indicator
3) Sine bar
4) Vernier Caliper
283] Washer help to:
1) improve appearance
2) Distribute force over a larger area
3) Distribute force to the bolt
4) Cover the clearance hole of the workpiece
284] The relationship existing between the lateral strain and the axial strain is expressed by:
1) Poisson's ratio
2) Hook's law
3) Young's Modulus
4) None
285] Rackwell test is done to measure:
1) Hardness
2) Hook saw
3) Length
4) Ductility
286] The heat treatment generally carried out of soften the metal is:
1) Normalising
2) Annealing
3) Hardening
4) Carburising
287] A double cut file has rows if teeth the same as a single cut file and in addition
has a second row of teeth which are cut.
1) Across the first row
2) Diagonally to the first row
3) Parallel to the first row
4) On the edge of the file
288] Which of the following is a part of file?
1) Heel
2) Face
3) Tang
4) all of these
289] Centre punch has as included angle of:
1) 90 degree
2) 118 degree
3) 60 degree
4) 120 degree
29]
The best example for semi liquid lubricant is:
1) Grease
2) Graphite
3) Castor oil
4) Lord oil
291] what is the ratio of 10 feet to 30 inches?
1) 4 : 1
2) 1 : 4
3) 1 : 3
4) 3 : 1
292] Which tool is used to measure the tolerance between surface plate and a surface being
checked for flatness?
1) Depth Gauge
2) Surface Gauge 3) Thickness Gauge
4) Dial Test indicator
293] Universal dividing head is used for indexing work o:
1) Lathe
2) Milling machine 3) Drilling machine
4) Slotting machine
294] best example for gravity feed lubrication is:
1) Grease Gun
2) Ring lubricator 3) A and B
4) Wick feed lubricator
295] A lathe having swing over bed at 220 mm can accommodate a component of diameter:
1) 110 mm
2) 220 mm
3) 95 mm
4) 440 mm
296] how many seconds are there in angle of 6 degree?
1) 21600 sec
2) 1800 sec
3) 2160 sec
4) 18000 sec
297] Internal dia is measured by:
1) Vernier caliper 2) Ring Gauge
3) Outside micrometer
4) Inside micrometer
298] The best example for splash lubrication:
1) Ring lubricator 2) Wick feed lubricator
3) Grease gun
4) Pump lubricator
299] Angle of square thread is:
1) 45 degree
2) 90 degree
3) 60 degree
4) 80 degree
300] Drilling jig is a device for:
1) Holding the job 2) Grinding the job 3) Burning the job 4) Holding the job and grinding the tool
301] The machine element while control the sequence of operation is auto drive lathe is:
1) Cam
2) Bears
3) Belt & Pulley
4) Screw rod
302] In grinding chatter marks can be avoided by:
1) Proper balancing of the wheel
2) using excess of coolant
3) Using rubber sheets
4) Reducing RPM of wheel
303] Best example for driving fit is:
1) Ball bearing one shaft
2) Tyre on the rail wheel
3) Pulley with key on the shaft
4) Cart rim o the wooden wheel
4) Radius of job
3) Annealing
4) Cad plating
3) To increase carbon
4) None of these
3) Centimetre
4) Metre
3) 0.001 mm
4) 1.0 mm
3) Threads
4) parallelism
4) Radius
330] The temperature at which oil stop flowing and start Freezing:
1) Emulsification
2) Acidity
3) pour point
4) Flush Point
2) Return stroke
4) Depends on direction of force.
3) Hexane and Butadiene 4) None of these
3) 40 degree K
4) 40 degree K
3) 10 8 metres
4) 10 5 meters
3) Specific gravity
4) Viscocity
2) Convection
4) Conduction, Convection and radiation
3) Nut
339] The coolant generally used while machining with carbide tools is:
1) Kerosene
2) Water
3) Soluble Oil
340] If a piece of steel is reheated to a temperature of 200 degree to 250 degree Celcius
immediately after quenching the process is known as:
1) Tempering
2) Hardening
3) Annealing
4) Normalising
341] Snap gauge:
1) It is used to check the actual size of the finished job as to whether it lies within the prescribed limit
2) it is a solid cylindrical metal Piece, used to check the size of hole.
3) It is used to check the concentricity of the round jobs.
4) None of these
4) Broaching machine
4) Hydro fluoric acid
4) Dry
4) 8
4) Flux
4) Square Nut
360] Which one of the following key is used in change gears in a lathe?
1) Gib Head key
2) Feather key
3) Wood ruff key
4) Saddle Key
361] Which one is the correct Formula for speed ratio of pulley?
1) D(n = d X n
2) D ( d = N X n
3) D ( N = d X n
4) d X N = D X n
4) Push fit]
40 - 0.05
d)
40
+ 0.0
- 0.03
- 0.2
Which one of the following thread groups is only for transmitting motion ?
Square, Acme, buttress Threads
Unified, Acme, Square, Threads
Withworth, Acme, Square, Threads
ISO metric, Modified square, Acme threads
Gib adjustments for the ram are to be done?
Once in a week
b)
Once in a month
Once in a year
d)
Once in a five years.
379]
a)
c)
Shaping Machine
Broaching
380]
a)
b)
c)
d)
1: 20
1:50
1: 100
1:19:002 to
1:20: 047
Ans : 1-D
2-A 3-B 4-C
384] The tool used to get ' Good Finish' for a hole:
1) Drill
2) End Mill
3) Reamer
385] Match the following metals with melting points:
a)
Mild steel
A.
659
b)
Metric tapers
B.
1085
c)
Pin tapers
C.
1150
d)
Key and key way D.
1500 to
tapers
Ans : 1-D
2-A 3-B 4-C
385]
a)
b)
c)
d)
Ans : 1-A
2-C
3-D
4-B
4) Tap
2) Private
3) Co-operative Society
4) Elasticity
4) 440 V
4) Mulit-National Co.
4) 4
4) All the above
4) 270
3) Wood Discs
3) Depth
4) Internal thread
3) Internal diameter
4) External diameter
3) Small items
3) V tool
4) Pump
4) Square file
3) Longest side
4) Vertex
3) Sealing
4) Both B & C
3) Aircraft
3) Ampere
3) By sliding block
4) Walt
4) Tempering
419] Malleability is the property by means which the metal can be:
1) Rolled
2) Milled
3) Machined
4) None of these
4) Force
3) Stress
421]
The pitch diameter of an external threads can be measured by using:
1) Screw thread micrometer 2) Screw Pitch gauge 3) Thread ring gauge 4) All of these
422] The two most common bearing lubricants are:
1) Lubrex 57 and 68
2) Lubrex 58 and 67
3) Lubrex 47 and 38 4) None of the above
423] Which one of the following is a non-conventional machining process?
1) Honing
2) Reaming
3) Electro Chemical Machining 4) Spraying
424] which one of the following represents centre line in drawing practice?
1)
2)
3)
4) None of the above
Ans: 1
425] Spur gear can be manufactured by which of the following methods:
1) Milling
2) Hobbing
3) Shaping
4) All of these
426] Bonding is the term associated with:
1) Lapping compound 2) Milling cutter
3) Grinding Wheel 4) Twist drill
3) Pitch diameter
4) Pitch
4) Sine bar
2) It floats on water
4) It does not mix with water
3) .03135
4) .046875
3) Cos J/ Sin J
4) 1/secJ
3) Good shape
4) 0.000005 meter
4) Woodruff
4) Repeatable in measurement
*449] write the correct Trigonometric expression for Opposite Side/ adjacent side.
1) Cos
2) Sine
3) Tan
4) Secant
450] In an interference fit the shaft should be:
1) Oversize than the bore
2) Equalize than the bore
3) Undersize than the bore
4) under or oversize then the bore
450] Carbide tipped tool used for turning hard material is provided.
1) Side rake angle 2) back rake angle
3) positive rake angle
451]
the plastics which are formed is to shape by the application of heat and pressure without any
chemical change are known as:
1) Thermo setting plastics 2) Thermo plastic 3) Instruments
452] couplings are used to connect the shaft, when the shafts are:
1) The joined permanently
2) to be disconnected often
3) in misalignment
4) To be disconnected often and to compensate a
Misalignment between two shafts.
453] The cutting angle for chisel for chipping of Mild steel.
1) 45
2) 30
3) 55
4) 68
454] The Jig is made from a single block of steel to the smaller work piece is called..
1) Channel jig
2) Sandwich jig
3) box jig
4) Solid jig
455] A block Spirit level is used for checking the
1) Horizontal level only
2) Vertical level only
3) Horizontal & Vertical only
4) Angular alignment only
456] The value of one thimble scale division in a metric micrometer is
1) 1 mm
2) 0.5 mm
3) 0.02 mm
4) 0.01 mm
457] Which type of fir tis used in the inner race with shaft while mounting a ball bearing>
1) Precision slide
2) Large Clearance
3) Loose running 4) Interference
458] Which screw is used to connect the collar and shaft in a position?
1) Hexagonal socket set screw
2) Square head screw
3) Hexagonal head screw
4) Pan head screw
459] The main purposes of screw pitch gauge is..
1) To check the minor diameter of screw thread 2) to check the limits of screw thread
3) to check the distance between adjacent crest,
4) to check the major diameter of screw thread.
of screw thread
460] The soft material particles get clogged in the grinding wheel while grinding. This is called
1) Truing
2) Loading
3) Glazing
4) Dressing
461] Normal hardening temperature of less than 0.83 % carbon plain carbon steel is..
1) below the upper critical range
2) above the upper critical range
3) below the lower critical range
4) above the lower critical range
462] The measuring stylus of a mechanical surface indicator is made of..
1) Tool steel
2) Carbide
3) Diamond
4) Cast alloy
463] If the dimension of a component is finished within the limits of size, then it will be.
1) Minimum size
2) Basic size
3) Acceptable size 4) Rejected size
464] What will happen if the spindle thread are worn out in agate valve?
1) Value hard to turn
2) Loud noise when turn the valve
3) Water flow around the stuffing box
4) Valve will not close or open when the spindle turns
465] Why the woodruff keys are used on small tapered shafts with assembly?
1) It takes heavy load
2) It takes the shear stress
3) It is easy to fit and self align with key way of hub
4) It is less expensive
Advantages of:
466] what are the Advantage of Surface plate?
1) To measure the smoothness of the job 2) To check or mark angle of job with helps of sine bar
3) To measure right angle of job
4) To check the jobs produced in less time to
5) To measure a job with a dial test indicator
467] what are the advantage of surface gauge?
1) To draw lines parallel to its base
2) To find out the centre of cylindrical and square rods
3) To draw lines parallel to plain arm of a job 4) To properly Focus the job on the lathe.
5) To draw parallel line like height gauges on normal job
468] what are the advantages of Gauges.
1) Their use saves time as a number of jobs can be check in little time
2) Semi skilled technicians can also help in production by using these gauges.
3) There is no need of Employee for inspection and examination at production stage.
4) There is a little possibility of defects in the jobs
5) Rate of Production is increased
469] what are the advantages of slip gauge or Gauge block?
1) To verify Micrometer and Vernier caliper
2) To set adjustable gauge such as snap gauges.
3) To use sine bar
4) for exact Marking of job
5) To make solid snap gauge and caliper
6) to verify Measurement of a job with help of comparator
470] what are the advantage of Heat Treatment?
1) Hard metal can be softened
2) Soft metal can be hardened
3) Metallic job can be made machinable
4) Inner Structure of Metal can be changed
5) The mechanical Properties of metal such as Tensile Strength and compressive Strength can be
decreased or increased
471] what is the Advantage of anti Corrosive Treatment?
Ans: These treatments improve life and out-look of a job
472] what are the advantages of Threads?
1) To join two parts of a machine like nut bolt and stud
2) To get mechanical levers for lifting Weight such as chain pulleys jockey etc.
3) To accuracy in precision instruments like micrometer
4) For transferring the mechanical power
5) For speed control purpose
473] what are the advantage of cutting Fluid (Coolant)
1) If acts as a lubricants the tool and job 2) It increases the working life of a tool
3) It improves the job finish
4) It does not allow the chips to stick at the tool
5) It increases cutting speed
6) It protects the cutting edges of tool against any possible
damage
at a high temperature
474] what are the advantages of Grinding?
1) Jobs can be made true to the given measurement
2) A fine finish can be given to the job
3) Unnecessary metal cutting is avoiding
4) Production time is saved
5) Production cost is reduced and overall production is increase.
518] During Arc Welding, the correct angle of the electrode with the welding line is
a. 90
b. 40-50
c. 70-80
d. 45
519] The current range for a M.S. Electrode 4 mm is:
a. 150 to 250 amps b. 70 to 110 amps
c. 130 to 170 amps d. 60 to 90 amps
520] Stag entrapping in a weld is called:
a. Under cut
b. Porosity
c. slag inclusion
521] Standard drill angle is equivalent is:
a. 125
b. 106
522] High surface finish is obtained by:
a. Turning
b. Milling
d. incomplete penetration
c. 118
d. 90
c. Grinding
d. Lapping
523] If the weld metal fails to reach the root of the joint the defect is called:
a. Slag inclution
b. Incomplete penetration
c. Undercut
d. Porisity
524] The shaft angle are centre drilled for:
a. supporting jobs between centres
c. Reducing the weight
525] Hexagonal Nut having No. of faces:
a. 16
b. 4
d. 6
d. C Clamp
529] A body recovering original dimension when the applied load is removed is known as:
a. Brittle
b. Plastic
c. Annealed
d. Elastic
530] What is meant by NC in manufacturing?
a. Nitric Chloride
b. Nitro Carbide
c. Numerical Control
d. Number Code
d. Light weight
532] Broaching is a:
a. Inspection process
c. Administrative Process
533] The material used for grinding wheel
a. Boric Oxide
b. Brass Oxide
534] SWG means:
a. Safety Welding Gloves
c. Servicing wire Gauge
b. Photographic Process
d. Manufacturing Process
c. Aluminium Oxide
d. Iron Ore
d. Shaper
c. Lathe spindle
d. Tail Stock
d. Seven colours
540]
When the taper is expressed as a 1:10 ration and length of the job is 100 mm then the offset is
equal to:
a. 5mm
b. 10 mm
c. 25 mm
d. 1 mm
541] A Nut is to be made for a screw of M10 X 1.5 what should be size of drilled hole?
a. 10 mm
b. 9.5 mm
c. 9.0 mm
d. 8.5 mm
542] Which one of the following is used for removing a broken tap?
a. Tap Nut
b. Tap Wrench
c. Tap Extractor
d. Tap Disposer
543] Parallels and V-blocks made in two grades:
a . Grade A and B
b. Grade C and D
c. Grade A and D
d. Grade C and B
544] If steel is heated to a suitable temperature and then slowly cooled the steel will be:
a. Soft weak and ductile
b. Hard and brittle
543] If steel is heated to a suitable temperature and then rapidly cooled ( quenched ) the steel will
be:
a. Soft weak and ductile
b. Hard and brittle
544] A.C.P. Means:
a. Adjustable Cement pipe
c.Alternative Channel pipe
c. Leather
d. Card board
d. Internal thread
b. On irregular jobs
d. If smooth file is not available
b. Inspection room
d. Neither 'a' nor 'b'
d. Electric goods
c. Chuck Nut
d. Castle Nut
d. Sandwich jig
c. Gear
d. Drives
c. Dressing
d. Finishing
c. 1.0 to 1.2%
d. 1.2 to 1.4%
c. 0.60 to 0.75%
d. 0.20 to 0.30%
c. 0.6 to 0.7 %
d. 0.15 to 0.3 %
c. Good person
620] This calipers is used while marking the centre of a round bar:
a. Outside caliper b. Vernier caliper
c. Jenny Caliper
621] While marking curved lines, use the:
a. Offset scriber
b. Jenny caliper
c. Divider
c. V threads
624] while fixing the fitter's vice on the bench, the normal height would be:
a. Equal to the operators shoulder
b. 400 mm from the ground level
c. 40 inches from the ground level.
625] The flat chiesel has a slight convexity on the cutting edge because
a. To control the temper b. To move along the line freely c. To resist blows on deep cutting
626] To know the length of hacksaw blade measure it from:
A. End to end
b. One pin hole to other pin hole
c. The centre of the two pin holes
627] To determining the length of a file, it may be measured from:
a. tip to shoulder
b. Tip to tang
c. Tip to inner heel
628] Draw filing is done:
a. to keep up the accuracy b. before wing smooth file
c. Charcoal
When the taper shank of the drill is larger than the machine spindle the device to hold the drill
is a:
a. Drill sleeve.
b. Taper socket
c. Drill drift
d. Chuck and key
645] The suitable cutting fluid for precision grinding is:
a. Soluble oil
b. Synthetic soluble oil
c. Neat oil
646] The Morse taper provided on drills ranges between:
a. MT 1 TO MT 5 b. MT 1 TO MT 4
c. MT 0 TO MT 5
d. Thread rollers
650] You have to file on aluminium block to a smooth finish which one of the following cut of type is
most suitable
a. Double cut
b. Curved cut
c. Rasp cut
d. Single cut
651] In micrometer, graduations is marked on:
a. Anvil
b. thimble
c. Spindle
652] Which one of the following chisel is to be used for chipping the grooves?
a. Flat chisel
b. Cross cut chisel
c. Half round nose-chisel d. Web chisel
653] What coolant is suitable for drilling cast iron?
a. Kerosene
b. Water soap emulsion'
c. No coolant
654] Which one of the following is an artificial abrassive?
a. Emery
b. Diamond
c. Corrundum
d. Soluble oil
d. Silicon carbide
655] Which one of the following cutting fluids is used during grinding mild steel?
a. Mineral oil
b. Non synthetic cutting oil
c. soluble oil
d. paraffin
656] Mushroom headed chisel should:
a. While cutting on keyways
b. Always for safety
c. When reducing the metal rapidly
d. None of these
657] The magnifying glass is used:
a. While chipping b. While grinding c. While reading accurate measurements d. While drilling
c. Screws
c. Prevent oxidation
673.
A lathe carrier used for turning in between centres. Which one of the following accessories is
used along with it ?
a. Collet check
674.
d. None
b. Rake angle
c. Clearance angle
b. Running fit
c. Driving fit
d. Force fit
b. Araldite bonding
c. Riveting
d. Soldering
b. Strain
c. Yield point
d. Factor of safety
b. Tempering
c. Annealing
d. Corburising
b. Drift
c.Face plate
d. Chuck
c. 32oC
d. 100oC
c. Aluminium coating
d. Painting
a. 0oC
686.
c. Taper
a. Collect
685.
b. Square
a. Nitriding
684.
d. Vegetable
a. Stress
683.
c. Soluble oil
a. Two shafts
682.
b. Kerosene
d. Roots
a. Push fit
680.
c. Crests
b.Flanks
The angle of inclination of the thread to the imaginary perpendicular line is called :
a. Helix angle
678.
d. 3 jaw chuck
a. Parallel
677.
c.Driving plate
You have to cut threads on aluminium. Which of the following coolants you will use?
a. Lord oil
676.
b. Steady rest
In a threaded assembly the contact between the male and female threads take place on the:
a. Pitch
675.
d. Nails
b. 212oC
Anodising process on
a. Zinc coating
b. Tin coating
687.
a. 2000oC
688.
b. 3200oC
b. Side by side
c. Both a and b
d. 6000oC
c. 5000oC
In one complete revolution of the bull gear wheel the ram gets:
d. None of these
691.
a. Parallel motion
692.
c. Drilling m/c
d. Shaping m/c
b. Micrometer
c. Vernier
a. Square
695.
b. Lathe m/c
a. 3 wire method
694.
c. Perpendicular motion
a. Boring m/c
693.
b. Inclined motion
b. Vee
c. Acme
d. None of these
696.
a. Temerature of threads
697.
In which of following operation on the lathe the spindle speed will be minimum:
a. Taper turning
698.
b. Length jobs
d. None of these
In turning operation:
a. Tool rotates
701.
d. Thread cutting
a. Holding parts
700.
c. Fine finishing
a. Combination set
699.
b. Partening off
b. Job rotates c. Both tool and job rotates d. Both fool and job do not rotates
d. Slotting operation
a. H.S.S.
b. Carbon Steel
d. Carbide tools
703.
a.
Turning
704.
Which is the following type of bonding is generally used in manufacture of grinding wheel?
a.
Vetrified
705.
a.
b.
b.
Miling
c.
Rubber
Grinding
d.
c.
Shellac
b.
c.
Wear of bond
d.
706
a.
b.
c.
d.
715]
d.
716]
Abrasive is a very:
a.
Soft
717]
a.
Al2O2
718
a.
Jigs
719]
Which one of the following is used for marking quickly on a number of job:
a.
Surface plate b.
720
a.
700oC
727.
Male part is less than female part (shaft size is lesser than hole size):
a. Clearance fit
728.
b.
Al3O3
c.
Fixture
Template
300oC
c.
c.
c.
b. Interference fit
Mild
Al2O3
Rivet
Scraper
3000oC
c. transition fit
d.
Liquid substance
d.
Al1O1
d.
d.
d.
Divider
Divider
200oC
d. None of these
b. Square head
c. Protractor head
d. None of these
b. Extension tap
c. Hand tap
d. Intermediate tap
a. Morse taper
731.
b.
c.
Which tap is come in sets 1st tap, 2nd tap, 3rd tap?
a. Machine tap
730.
b.
Hard
Which one of the following part of the combination set is used for marking and measuring 45 o
to 90o angles?
a. Centre head
729.
b.
c .Metric taper
d. A and C
a. Clearnance angle
d. None of these
732.
c. 40 to 65 T.P.I
742.
743.
744.
745.
746.
747.
748.
d. Carpenter shop
How many teeths are cut per inch in the bastard file:
a. 20 to 30 T.P.I
741.
c.Fitter shop
d. 35 to 40 T.P.I.
749.
780.
a. Limiting friction
b. Liquid friction
c. Sliding friction
d. Gas friction
e. Rolling friction
f. Boundary friction
782.
a. Case hardening
783.
784.
785.
Necking
b.
Fullering
c.
Finishing
d.
Setting stock
786.
787.
788.
g. Solid friction
d. Induction hardening
789.
790.
b. Hard solders
a. Hydrochloric acid
b. Zinc chloride
c. Ammonium chloride
d. Resin
792.
e. Paste
793.
b. Hydrogen gas
c. Coal gas
794.
795.
c. Carburising flame
796.
b. Lap joint
d. Corner joint
e. Edge joint
797.
b. Horizontal position
d. Over head position
798.
799.
800.
801.
b. Straight polarity
805.
806.
807.
808
809.
810.
811.
812.
813.
814.
815
816.
817.
a. Ordinary centre
d. Ball centre
818.
b. Half centre
e. Pipe centre
c. Tipped centre
f. Revolving centre
819.
820.
821.
822.
823.
824.
825.
Name the different types of machine screws used in heady duty assembly.
Ans. a. Hexagon head screws
b. Hexagon socket head cap screws.
c. Square head countersink head screws
840.
841.
842.
843.
844.
845.
846.
847.
848.
b. Strap wrench
b. Block level
849.
850.
851.
Ans.
a. Natural adhesive
852.
Ans.
a. Fixed type
853.
Ans.
854.
b. Synthetic adhesive
b. Removable type
b. Sulphur grouting
a. Jib cranes
856.
b. Travelling crane
c. Gantry crane
a. Dot clutch
b. Cone clutch
c. Air clutch
d. Centrifugal clutch
857.
858.
Ans.
Ans.
c. Hydraulic press
b. Use of punch
862.
863.
Name the different methods bending rods and pipe in a bench vice:
Ans. a. Bending using bending jaw
b. Bending with Fixture
c. Bending with bending die
864.
Name the different methods used for checking minor diameter of external threads:
c. Rockwell method(HR)
d. Shore method
866.
a. Forced feed
867.
c. Splash method
a. Straight filing
868.
b. Gravity feed
b. Cross filing
c. Draw filing
a. By hand
b. By lathe
d. By milling
c. By casting