Professional Documents
Culture Documents
VPEG Sequence Control ST16 PDF
VPEG Sequence Control ST16 PDF
SEQUENCE CONTROL
(SEQUENCE TABLE)
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
The ST16 block has a sequence control function that handles a total of 64 I/O signals and 32
rules. The I/O signals can also be redistributed in the 8-signal unit.
The rule extension block (ST16E) is used for extending the rules of ST16 block. It connects
to an ST16 block and only allows connection to a step-type ST16 block. Hence, it cannot be
used/activated independently.
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
Action Signal
Rule Number
Condition Rule
Action Rule
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
THEN
Execute the next step label when the
corresponding rule condition status is true or
satisfied & after the manipulated output is
completed.
ELSE
Execute the next step label when the
corresponding rule status is false.
Data
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
Processing Timing
Scan Period
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
Invoking function
block
ACT.OFF
Sequence process execution
Executing
One-shot type
function block
Idle
One-Shot Processing Conceptual Diagram
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
False
Action change/interuption is
possible eventhough the
conditions rule are satisfied
True
Action rule
change
False
Output Only When Conditions Are Changed Conceptual Figure
Note:
Note
However, if non-latched output is specified for the action signal, the operation changes when the
condition is switched from true to false.
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
False
Action change/interuption is
not possible as long as the
condition remains satisfied.
True
Action rule
change
False
Output Each Time Conditions Are Satisfied Conceptual Figure
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
LAHH100.PV
LAH100.PV
LAL100.PV
LALL100.PV
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
Water injection
processing
(Step label A1)
Water drain
processing
(Step label A2)
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
Water injection
processing
(Step label A1)
Water drain
processing
(Step label A2)
In the above sequence table, rules number 01 & 02 are step A1. Rules
number 03 & up are step A2. Rules number o5 and beyond do not have any
Y/N pattern for the condition rule or action rule or move-destination step
label, so they are not subject to condition testing nor action execution.
Step A1 monitors the conditions for rules number 01 & 02 simultaneously.
Whichever the condition is satisfied will be executed. Executing the action of
rule 01 does not advance the step since there is no designation in the movedestination step label. After executing the action, A1 resumes monitoring
rules number 01& 02 again. When rule number 02 conditions become true,
the action of rule 02 is executed & the step advances to A2 as stated in the
move-destination step label.
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
56
16
48
24
40
32 (default)
32 (default)
40
24
48
16
56
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
Calculation Blocks
Faceplate Blocks
SFC Blocks
I/O data that can be processed in a sequence table are shown below.
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
1 to 99
SWCR[5]: 0 to 15
SWST[5]: 0,1
SWOP[5]: -15 to 15
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
PT YOKOGAWA INDONESIA
Training Center Technical Support Group
LABORATORY WORKS
Create a logic sequence from these control narratives:
Case 1
In a cascade loop, if the process variable of the slave controller is HighHigh alarm then the slave controller mode will have to switch to
CASCADE mode and the master controller mode will have to switch to
AUTO mode.
However, the operator is allowed to change the mode of slave controller
to MANUAL or AUTO mode even tough the process variable is still in
High-High alarm state.
Case 2
In a cascade loop, if the process variable of the slave controller is HighHigh alarm then the slave controller mode will have to switch to
CASCADE mode and the master controller mode will have to switch to
AUTO mode.
The control mode of the slave controller cannot be changed until the
alarm vanishes (process variable is in normal state).
PT YOKOGAWA INDONESIA
Training Center Technical Support Group