Professional Documents
Culture Documents
Dgca Paper-2-Oct-2010
Dgca Paper-2-Oct-2010
c) no nozzle obstruction
d) all of the above
10) MTCS regarding a/c tie down
a) In manila rope 1 inch of slackness should be provided
b) Tie down is not always necessary in case of light a/c
c) Dacron rope shrinks when wet
d) All of the above
11) MTCS regarding jacking
a) Four jacking points are provided to jack the a/c
b) Parking brake should be applied
c) Raise the a/c at least 6 inch from the ground
d) All of the above
12) MTCS regarding common screw driver
a) Common screw driver fill at least 90% of the screw slot
b) The common screw driver is used only where slotted head screws or
fasteners are found on a/c
c) Both a and b
d) none
13) MTCS
a) Brazing requires less heat than welding
b) Brazed joint is not so great as welded joints
c) Brazing is not used for structural repairs on a/c
d) All of the above
14) MTCS regarding welding
a) welding is the process of joining metal by fusing the materials while they are
in a plastic or molten state
d) both b and c
20) In straight and level flight
a) lift equals drag and drag is the resistance of the air to objects moving through
it
b) thrust equals weight and thrust is derived from jet propulsion or from a
propeller and engine combination
c) lift equals weight but thrust equals drag
d) all are correct
21) Variable delivery pump in hydraulic system
a) has a fluid output that is varied to meet the the pressure demands of the
system
b) forces a unvarying quantity of fluid through the outlet port
c) as in 1 and has a pump compensator within the pump
d) as in 2and has a hydraulic module controller
22) Frequency range used for space propagation
a) 30 MHz
b) Above 30 MHz
c) 20khz to 40 kHz
23) Angle of attack is the
a) Angle between the chord line and the relative wind
b) Angle between the chord line and the longitudinal axis
c) Angle between the longitudinal axis and the mean camber line
24) Primary control surfaces
a) Aileron rudder and trailing edge flap
b) Ailerons rudder and leading edge flap
c) Ailerons rudder and elevator
d) Rudder elevator and vortex generator
b) Buna n
c) Neoprene
d) Both a and b
37) Corrosion is the deterioration of metal by
a) Chemical attack
b) Electrochemical attack
c) Both a and b
38) Corrosion appearance in Al and Mg alloys
a) Appears as surface pitting and etching
b) Grey powdery deposit
c) White powdery deposit
d) All of the above
39) The agents which are responsible for direct chemical attack are
a) Residual flux deposit
b) Spilled battery acids or fumes
c) Caustic solutions entrapped
d) All of the above
40) NF thread specifies
a) 12 threads per inch
b) 14 threads per inch
c) Same as UNF thread
41) A/c bolts are manufactured in
a) class 3 fit
b) class 4 fit
c) free fit
d) loose fit
b) Rockwell
c) Barcol
d) Both b and c
48) The hardness testing gives
a) Result of heat treatment
b) The state of a metal prior to heat treatment
c) Gives details of tensile strength,wear resistance
d) All of the above
49) The electric current is
a) The flow of electrons from positive point to a negative point
b) The flow of electrons from negative point to a positive point
c) The current flows because of same electric pressure between the two points
50) Resistance depends upon
a) Shape of cross-section,length,area
b) Area,length,material
c) Length, shape of cross-section, temperature
51) Common method of identifying ferrous metals
a) AISI
b) SAE
c) Spark test
d) All of the above
52) SAE 44XX indicates
a) Nickel steel
b) Molybdenum steel
c) Chromium steel
d) None
10
12
13
c) The a/c and fuel truck are held at common electrical potential by a
conducting wire
d) Both b and c
74) When a p n junction diode is connected with a single wire
a) There is a steady current flow through the wire
b) No steady current flows
c) Current may flow but depends upon resistance
d) None
75) Types of corrosion
a) Direct chemical attack
b) Electrochemical attack
c) As in 1 and 2 but affects internal surface only
d) As 1 and 2 affects both internally and externally
76) Universal gates are
a) NAND and NOR
b) AND and OR
c) NOR and XOR
d) None
77) Convert 29 into binary
a) 10100
b) 11101
c) 10011
d) 10010
78) Decimal equivalent of F8E6
a) 63718
b) 69218
c) 61216
14
d) 65432
79) MTCS
a) Turbofan requires shorter runway than turbojet
b) Turbine engines are economic at higher altitudes
c) Turbojet has more turbine stages than turbo shaft
d) All of the above
80) Lead acid battery MTCS
a) Positive plate is made up of lead peroxide and negative plate made of spongy
lead
b) Electrolyte is dilute sulphuric acid and water
c) At discharge state both plates form lead sulphate and water level of
electrolyte increases
d) All of the above
81) In a/c air-conditioning and cooling cycle system the type of turbine
used
a) Axial flow
b) Inward flow
c) Outward flow
82) Jo bolt is
a) Internally threaded three piece rivet
b) Externally threaded three piece rivet
c) Internally threaded four piece rivet
83) The type of welding used in stainless steel
a) Seam welding
b) Spot welding
c) Butt welding
d) Gas welding
15
b) 1/32 inch
c) 1/16 inch
d) 1/8 inch
88) Identify the given figure
16
a) Drive punch
b) Speed handle
c) Extension bar
a) Outside caliper
b) Inside caliper
c) Hermaphrodite caliper
90) Identify the given figure
a) Centre punch
b) Starting punch
c) Hollow punch
91) Identify the given hammer
a) Ball peen
b) Straight peen
c) Cross peen
17
b) Flute
c) Margin
a) .2956
b) .2944
c) .2765
d) .2987
94) Voltage drop across R3,R2 and R1 is in the order of
18
a) 2 amperes
b) 3 amperes
c) A amperes
96) The punch which is used for driving out damaged rivets
a) Prick punch
b) Drive punch
c) Centre punch
ANSWER SHEET
SL
NO
ANSWE
R
REFERENC
E
9A-529
9A -532
19
9A-532
9A-538
9A 534
9A-143
9A-500
9A-501
9A-501
10
9A-511
11
9A524,525
12
9A-529
13
15A-261
14
15A-247
15
15A-43
16
15A 31,32
17
15A-32
18
15A-34
19
15A-35
20
15A-34
21
15A318,319
22
15A-520
23
15A-31
20
24
15A-40
25
15A-252
26
15A-309
27
12A-30
28
12A-28
29
12A-28
30
12A-66
31
9A-100
32
9A-102
33
9A-121
34
9A-151
35
9A-151
36
9A-165
37
9A-171
38
9A-171
39
9A-171
40
9A-121
41
9A-121
42
9A-123
43
9A-127
44
9A-132
21
45
9A-143
46
9A-205
47
9A-218
9A-218
49
9A-271
50
9A-273
51
9A-195
52
9A-195
53
9A-201
54
9A-201
55
9A-203
56
9A-205
57
9A-273
58
9A-290
59
9A-294
60
9A-307
61
9A-314
62
9A-314
63
9A-332
64
65
9A-344
9A367,368,3
69
48
22
66
9A-366
67
9A-417
68
9A-473
69
9A-477
70
9A-479
71
9A-498
72
9A-498
73
9A-499
74
9A-370
75
9A-171
76
77
78
79
80
9A
307,308
81
82
9A-124
83
15A
WELDIND
84
9A-57
85
9A-102
86
9A-340
23
87
9A-542
88
9A-533
89
9A-544
90
9A-531
91
9A-529
92
9A-538
93
9A-546
94
95
96
9A-531
24