Professional Documents
Culture Documents
18
B.
34
17
25
5. Complete the equation by correctly identifying the missing part of the calculation from
(A)
(B) 16.75
(C) 17.25
(D) 421.5
(F) 12 X 1.5
CHEMICAL
1.
The fluid property which matters for falling rain drops to acquire spherical shape is
a.
Pressure
b.
Height of descend
c.
Viscosity
d.
Surface tension
2.
[(
( )
b.
c.
Molten metals
d.
All a, b and c
3.
What is the overall transfer function (CR) of the following block diagram,
if G =G1. G2 .G3 and H = H1 .H2?
a.
1/1+GH
b.
G/1+GH
c.
H/1+GH
d.
G/1-GH
CHEMISTRY
1. A 0.1M aqueous solution of unknown white crystalline substance shows a precipitate when
treated with AgNO3 solution and turn a phenolphthalein solution pink the unknown substance
could be?
a.
NH4Cl
b.
K3PO4
c.
KNO3
d.
NaCl
2. The species Ar, K+ and Ca2+ are isoelectronic (have the same number of electrons)
In what order do their radii increase?
Smallest
Largest
Ar
Ca2+
K+
Ar
K+
Ca2+
Ca2+
K+
Ar
K+
Ar
Ca2+
Br2
b.
Na+
c.
NH3
d.
CN
CIVIL
1.
When a body is subjected to two equal and opposite forces, acting tangentially across the resisting
section, as a result of which the body tends to shear off across the section, the stress and strain
included is
2.
3.
a.
b.
c.
d.
Two fixed beams A and B are shown in the following figure. The ratio of maximum deflection of beam
A to maximum deflection of beam B is
a.
1/2
b.
c.
1/4
d.
1/3
1
2
/8
b.
400 kg / m
d.
800 kg / m
a.
200 kg / m
c.
600 kg / m
ELECTRICAL
1.
A wire of 0.14mm diameter and specific resistance 9.6 micro ohm-cm is 440 cm long. The resistance
of wire will be
a.
9.6
b.
11.3
c.
13.7
d.
27.4
2.
a.
c.
In a transformer, the magnetic coupling beteen the primary and secondary circuit can be increased
by
Increasing the number of turns
b. Using soft material for windings
Using the magnetic core of low
reluctance
d.
3.
The efficiency of a 430/200 V transformer at full load 0.8 p.f. lagging is 95%. The efficienc at full
load 0.8 p.f. leading will be
a.
99%
b.
95.0%
c.
95%
d.
90
ELECTRONICS
1.
Which of the following element does not have three valence electrons?
a. Boron
b.
Aluminum
c.
2.
3.
Gallium
d.
Phosphorous
In which of the following cases will the capacitor complete its discharge most rapidly?
a.
b.
c.
A 50 pF capacitor wih a 20 m V
charge discharging through a 200
milli-ohm resistance
d.
a.
b.
c.
d.
INSTRUMENT
1.
Two characteristics which fully define the input and output respectively of a BJT in Common Emitter
configuration are
A.
B.
C.
D.
Both a and b
2.
Which of the following acronyms pertains to an obsolete digital circuit technology wherein logic gates
are built using only transistors and resistors?
A.
RTL
B.
RTD
C.
RTT
D.
RTC
3.
In this network, what are the state variables for state-variable representation?
A.
B.
C.
D.
MECHATRONICS
1.
A rigid beam is supported by a pin at end A and by a roller at end B. The length of the beam is 5m. A
vertically downward force of 6kN acts exactly at the center of the beam. What are the vertical reactions at
supports A and B?
a.
b.
c.
d.
2.
3.
a.
ON condition
b.
Off Condition
c.
No such switch
d.
None of above
a.
b.
Active region
c.
Saturation region
d.
Not all
MECHANICAL
1.
2.
A fluid that can be considered to be both incompressible and friction less is called:
a.
A laminar fluid
b.
A Turbulent Fluid
c.
A Eulerian Fluid
d.
An Ideal Fluid
a.
b.
g/2
c.
d.
2g
3.
An engine absorbs heat at a temperature of 727 C and exhausts heat at a temperature of 527 C. If the engine
operates at maximum possible efficiency, for 2000 joules of heat input the amount of work the engine
performs is most nearly.
a.
400 J
b.
1450 J
c.
1600 J
d.
2000 J